Search Documents

By S. Bhattacharaya, S. Aich, B. K. Nandi

"At present scenario, there has been an increasing demand in the usage of blend coal in power sector; regardless of how, specific knowledge on burning and ignition characteristics and their interactive effects is stingy. In this work a detailed investigation was therefore taken up to study in detail the combustion characteristics of selected coal samples and their blends. Certain parameters were believed to have significant effects on combustion characteristics of individual coal and their blend. Major parameters identified for this purpose included proximate analysis, combustion conditions, heating rate, reaction regions, blending ratios, ignition condition, reactivity (or reaction rate) and burnout temperatures. With the help of these parameters, thermal features and reaction kinetics of the individual and blended samples were investigated through a qualitative and quantitative thermo-gravimetric analysis of two different individual coals and their blend carried out in an oxygen atmosphere from ambient to 800 0C at a constant heating rate of 10 K/min. A significant difference in terms of rate of mass loss with temperature correlated from Arrhenius expression along with coal-coal blend interactions and deviation from their expected behaviour, have been observed between the kinetics of individual and blend samples, the latter showing better ignition performance and comprehensive combustion phase. It was also found that particles having the lowest percentages of volatile matter and ash could possibly be blended with particles having high ash and volatile matter to meet the required burning condition which can be effective in terms of cost savings, improved fuel economy, reduced undesirable exhaust emissions and improved safety of coal burning equipment. Experimental results further indicated that individual samples and coal blend samples have different combustion features in terms of residue left, peak temperatures and activation energies. Thermodynamic activation parameters such as activation energy, pre-exponential factor and order of reaction were computed from the thermal data using the modified form of non-isothermal methods. INTRODUCTION Coal has been the most significant source of energy for India and would remain so at least for the next few decades. About 60-65% of the electricity produced in India is from coal fired power plants. Indian coal is of drift origin and of high ash content. Ash content of the coal burnt in power plants in India is in the range of 30-45%, most of it being Run-of-Mine coal. Most of the power plants in India source their coal from number of mines, most common being multiple sourcing. Usually coal from each source [1] is burnt separately. For various reasons mostly associated with logistics, burning of blended coal is rarely practiced. Blending of coal is practised mainly for improving the quality of available coal and meets the shortage of coal supply. Blending technique is generally practised in power industries to reduce the cost of power generation along with mitigating combustion performance or slagging problem ensuring consistency in as fired coal quality and also for environmental compliance. Blending good quality imported coal can improve coal quality and helps in preserving indigenous coal resources for longer period [2]. Use of blended coal shall reduce load on all boiler components (Mill, CHP, Boiler, AHP) & reduce O&M cost and increase the availability. The main purpose of blending is to get a blended as fired coal having ash, volatile matter and gross calorific value close to design coal and the two coals are to be blended in such ratio proportions that resultant coal blend have desired ash, volatile matter and gross calorific value [3]. For a coal to be blended certain parameters have to be considered to get compatibility with respect to combustibility ( Burn ability) of coal, grindability ( HGI), ash fusion behavior, swelling characteristics of coal, need to be checked"

Jan 1, 2017

By V. G. Hill

The term bauxite was first used by O.P.A.P. Dufrenoy in 1845 for an ore which was discovered by Pierre Berthier in 1821 near the village of Les Beaux de Provence near Arles in southern France. His data suggested that this mineral was an alumina hydrate with two molecules of water. However, it was subsequently shown by thermal analysis that the mineral was a fortuitous mixture of the mono-hydrate and the tri-hydrate. Diaspore had been previously discovered in 1801 and gibbsite in 1822. The term was however retained as a rock name. The name of the village was changed to Les Baux around 1885; Sainte Claire Deville suggested that the mineral name should reflect this, and it was changed to bauxite (Bracewell, 1962, Rkgnier, 1988). Mining of bauxite began around 1860 in the Auriol region in the Bouches du Rhine area in the south of France. This ore was transported toMarseilles by carts and was processed in the Salindres plant, which at that time was the only plant producing alumina using the Deville process and aluminum by the chemical process. During that period white bauxite (low iron content) was particularly sought after for the production of aluminum sulfate, refractory bricks, and quick setting cement. Export of bauxite from France began in 1880 and was initially delivered to Chemische Fabrik, Goldschmischen near Breslau, and to Guilini's Ludwigshafen plant in Germany in 1885. These companies produced alum and aluminum sulfate (RCg- nier, 1988). The next bauxite mining operation was in Antrim County in Northern Ireland in 1873. This was first used for the manufacture of alumina refractory bricks and quick setting cement (Bracewell, 1962). It is important to emphasize that initially almost all of the bauxite which was produced came from France and was mainly used for non-metallurgical purposes. At that time even the production of alumina was mainly for use as a mordant in textile dying. However, with the development of the Hall-Héroult process, the alumina which was available was increasingly used for smelting to aluminum. In spite of this the demand for non-metallurgical bauxite continued to increase and a set of applications were developed. These include refractories, abrasives (including the recently developed proppants), high alumina cements, aluminum chemicals, activated bauxite, and alumina. It became increasingly evident that the high alumina-low alkali raw materials have special advantages. The question however was one of cost benefit. Chin (1989) has pointed out that the non-metallurgical operations have been traditionally grafted on a bauxite/alumina/aluminum industry tree. In this context the non-metallurgical alumina produced was, with few exceptions, regarded as either coproduct or byproduct i.e.: Bauxite Trunk Sector Alumina Trunk Sector Aluminum Trunk Sector

Jan 1, 1994

By Michael F. Tucker

Dealing successfully with intercultural issues is critical for success on an international assignment. This is true not only for employees but for the accompanying spouses and children as well. This paper presents a set of research-based competencies required for successful life and work in another country, such as open-mindedness, flexibility, and respect for the beliefs of others. Best practices for training employees and their families bound for international assignments are also presented.

Jan 1, 2001

By Suresh P. Babu, Joseph W. Leonard, Richard Muter, D. P. Sen

OUTLOOK FOR COAL UTILIZATION In 1975, about 650 million tons of bituminous coal and lignite mined in the United States was used to meet 55% of the primary energy input for electric power generation and 26% of the total industrial consumption.1 Even though this amounts to only 21% of the total energy requirements, it is believed that with the declining natural gas resources and uncertainty of liquid fuel imports, coal will assume a more dominant role in suppplying our future energy needs. A regional breakdown of the coal reserves of the United States along with their characteristics is shown in Table I. At present the United Stares Energy Research and Development Administration (ERDA) and the US Bureau of Mines (USBM) are financing extensive research programs in advanced mining methods and energy conversion processes. The increased demand for wal which may result from these research programs may also create large-scale environmental protection problems. As more and more coal is mined the production of undesirable coal fines and dust also increases proportionally. The USBM and the Environmental Protection Agency (EPA) research in this field includes development in the areas of instrumentation for qualitative and quantitative analysis of wal dust, protective devices, and dust collectors. Dust control by water sprays, steam, and foam are also being investigated. Other aspects of safety in mining include developing methane drainage techniques prior to coal mining, fire and explosion prevention, and neutralization and disposal of acid mine waters. It is the belief of coal technologists that when the emphasis shifts to coal as the primary source of energy. the existing methods of mining and preparation of coal must be improved considerably to supply large quantities of quality coal for energy conversion. It is the objective of the present large-scale research financed by ERDA to produce substitute fuels from coal. Large-scale gasification pilot plants are being constructed by Bituminous Coal Research, Consolidation Coal Co., Institute of Gas Technology, and the Pittsburgh Energy Research Center to produce coal gas of natural gas standards at 1,000 psig. The processes being adopted by these pilot plants are oriented towards recovering most of the sulfur from coal by absorbing H2S and its subsequent conversion to elemental sulfur. The environmental protection standards will be strictly followed in using the results of these pilot plants to construct large-scale coal gasification plants in the latter part of the 1970's. With the increasing awareness of the need for air pollution control, considerable research is being done to minimize sulfur dioxide emission from thermal power plants. Utilization of limestone and dolomite scrubbing systems and caustic treatment of stack gases have proved to reduce sulfur and nitric oxide emissions by about 90 to 96%.3 Currently, about 22 scrubbers are in use in the United States to reduce sulfur in stack gas emission. In the long-term, it appears that optimal combinations will be developed involving both advanced coal preparation technology and wet scrubbing. The sulfur compounds are converted either to elemental sulfur of sulfuric acid. Besides the sulfur compounds, the major byproduct of the coal utilization industry is the large amount of coal ash. The Coal Research Bureau at West Virginia University has developed a practical use for coal ash as a structural material. The coal industry will undergo revolutionary changes when coal becomes the primary source of energy. New coal mining and preparation processes will be introduced to meet the ever-increasing per capita energy requirements. 2. BENEFICATION Introduction Coal preparation, like the beneficiation of ores, is also aimed at the separation of values from associated waste. Even though the unit operations involved when enriching ores and coal are similar, there are certain characteristics unique to coal preparation. Unlike the scattered and concentrated veins of underground minera1 ores, coal is distributed uniformly and very much in abundance in the coal mines. Coal occurs as the metamorphosed sedimentary deposits of vegetable matter, while metal and mineral deposits occur in great varieties of forms, structures, and origin-from igneous to sedimentary and metamorphic. The mined coal, being much more friable than mineral ores, is subjected to less intensive size reduction operations. Ores are usually ground to a very fine size for subsequent concentration, while coal is crushed to a coarser size, since considerably less liberation is needed to achieve the desired degree of separation. Since mineral matter is to a great extent discretely distributed in coal, concentration is mainly achieved by taking advantage of differences in specific gravity between clean coal and associated waste. In general, about 90% of coal is concentrated using specific gravity separation and about 10% by froth flotation. In contrast, these operations are frequently reversed in the beneficiation of ores. In coal preparation almost all fractions separated during various stages are made use of. while large amounts of gangue material are rejected in the concentration of ores. Hence, coal generally has a much lower ratio of concentration than ores. Since ore deposits are frequently more variable and mineralogically complex than coal, beneficiation of ore may require more plant flexibility and point-to-point quality control. This characteristic difference between the mineral ores and coal is attributed to the generally used one-step processing in coal as compared to the multiple-step processing of ores. Dewatering to enhance the energy content of coal is usually considered a major unit operation. Even though thickening and filtration are common for dewatering ore concentrates and cleaned coal, vibrating centrifuges and disk filters find unique application in the coal industry for achieving these types of solid-fluid separation. In coal preparation, thermal drying is carried out in separate units at the mine. While ore concentrates are usually dried at the smelter. Although the drying of ores is seldom considered dangerous, volatile matter and combustible dust are reasons why the thermal drying of coal can be hazardous. Open air storage of ores and mined coal results in partial oxidation. Unlike the oxidation of ores, the oxidation of the pyritic and carbonaceous constituents of coal together with the heat of condensation of moisture contribute to spontaneous heating and the subsequent combustion of coal in storage. Among the other significant difference between concentration of ores and coal are the weight and capacity of processing equipment. Coal processing employs less cumbersome, higher capacity units while the beneficiation of ores usually requires much more massive and frequently lower capacity equipment. Properties of Coal Which Influence Design The widely varying and heterogeneous composition of coal, due to metamorphism, determines the preparation design and uses of the resulting products. Petrography serves as a useful system of classification to identify the coal types present and their distribution. Early

Jan 1, 1985

Controlled-blasting experiments in small development drifts were conducted at CANMET's Experimental Mine in 1992 and 1993. The objective of these experiments was to develop suitable controlled-blasting techniques for small development headings that are drilled by jackleg with 32-mm-diam holes. The experimentation was also aimed at providing insight into blast-damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rock-mass structural data. The drift faces were approximately 2.4 by 2.4 m (7.9 x 7.9 ft) in size with 36 to 43 holes drilled to a depth of 2.4 m (7.9 ft). Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO was used as the main explosive and decoupled 19-mm (0.75 in.) diam semigelatin dynamite charges were used in the perimeter holes. Smooth-blasting techniques and presplitting were tested in the underground mine. All of the blasts were monitored with a multichannel blast-vibration monitor, to which was attached sets of high frequency geophones and accelerometers. These experiments demonstrated the efficiency of controlled-blasting techniques for the reduction of blast damage and also demonstrated the need to improve the safety and efficiency of using explosives.

Jan 1, 1997

By J. A. Herbst

Mineral liberation modeling can be traced back to the early work 0fA.M. Gaudin up through more recent population balance modeling by R.p. King, J.A. Herbst and G.T. Adel. A more micro-scopic look was taken at the University of Utah in the form of the J.E. Sepulveda and J.D. Miller Pargen model which permits the creation of an arbitrary shape, multiphase particle made up of discrete grains. Recent work on image analysis and tomographic analysis by J.D. Miller and C.L. Lin have laid the experimental ground work for model validation, but until now it hasn't been possible to include the necessary physics of the particle stressing process to allow the development of a 'ffirstprinciples"mode1 which does not presuppose a "mode” of liberation (e.g., random or by detachment). Recent developments in discrete grain breakage (DGB) modeling now make a generalized physics based model feasible. This paper describes current work that is being done to develop a physics based discrete grain liberation (DGL) model. Two-dimensional and three dimensional simulation results exploring the effects of particle size, phase properties and loading type are presented. Relationships between energy based liberation efficiency, degree of random liberation and material properties are identified.

Jan 1, 2005

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976

By F. L. Wilke

The prototype of an expert system, designed to assist layout planning of face operations, is presented. By specific combination of knowledge-based and conventional EDP techniques it has been possible to extend the known Kepner-Tregoe method up to the determination of mature layout solutions in difficult planning cases. It has been proven that the presented strategy - which can be applied to any kind of problem with similar structure - is apt to provide efficient EDP support for handling complex mining problems. Such support goes far beyond the purely numeric evaluation of envisaged alternatives.

Jan 1, 1989

By Rolando V. Cuaño

For geostatistical applications, heterogeneous spatial phenomena are better modeled as mixtures of populations. However, the modeling of the constituent populations can become complex. The alternative mixture model offers a simplified approach to the w modeling problem. The model is applied and tested on the Walker Lake data set. Compared to the univariate ordinary kriging model, the alternative model generates less biased block estimates.

Jan 1, 1996

By D. Hulse

"The science of “optimal economic pit design” has been highly refined in the last decades. Even with the proliferation of optimizing and heuristic algorithms exploiting ever faster computers, the most common input is a single block model and a single set of cost assumptions, each of which is an estimate and prone to errors. An analysis of price assumptions produces a suite of nested economic shells, each with its own quantities of ore, waste, grade, and profit, but due to irregularities in the mineralized body, the growth of these shells can be erratic. To control the impact of the errors of the model and cost assumptions when choosing the pit shell for design, graphs of pit shells characteristics, such as stripping ratio, cost per unit of product and profit/ton, can be analyzed to consider points with higher stability, or robust pits. Selection of robust shells for a pit limit and for push backs can help to understand the impact to profit and risk. The robust shells also guide the preferred solution sets for final pit and cutoff optimization. INTRODUCTION “An open pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface.” Optimum Design of Open-Pit Mines, Lerchs, H. and Grossmann, I. Transactions C.I.M. Volume LXVIII 1965. Traditionally an analysis of economic pit shells and sensitivity was performed by varying the input metal price. This was done with both floating cone algorithms as well as early versions of the Lerchs-Grossmann (L-G) algorithm. This gave an indication of the pit sensitivity to price but since other variables also change, some with metal price (perhaps steel and equipment), and some independently (fuel and tires) the understanding of these different pits was restricted. In addition, a run of the program could take hours, making a detailed analysis of small changes unwieldy. The L-G algorithm was programmed by a variety of people and sold as part of commercial mining packages, however it was first and most successfully commercialized by Jeff Whittle in 1984. When Whittle’s 3-D™ was expanded to 4-D the parameterization of the economic inputs was considered and the ability to run a suite of “pit shells” became automatic. The competing NPV Scheduler™ program sold by DataMine™ offers similar pit shell analysis capabilities."

Jan 1, 2018

By N. Demirel

Estimating productivity of a walking dragline is of paramount concern to mining engineers and mine planners. Risk based evaluation of the dragline productivity is a valuable tool to estimate the dragline?s long-term performances and availabilities, to develop preventive maintenance plans, and to make future projections about the machine?s performance. This paper aims to provide mining professionals with an overview of risk assessment methodology for productivity of two walking draglines, PAGE 736 and MARION 7820, which have been operating in Tunçbilek open cast coal mine of Turkish Coal Enterprises (TKI) in Turkey. The study encompasses three main stages as: (i) acquiring of monthly maintenance records, operating hours, mechanical and electrical failure hours between 1998 and 2009; (ii) reliability modeling using mean time between failure data; (iii) determining hazard rate and consequences to compute risk associated with dragline productivity. The results showed that that Page 736 (20 yd3) is seemed to be more reliable and less likely to fail when compared with Marion 7820 (40 yd3). The operating hours without failure range from 41 to 51 hours with 50 percent reliability.

Jan 1, 2011

By Thomas E. Newman

This paper is a case study using new laser-terrain-mapping technology by EagleScan, Inc., for creating topographic maps. Holnam, Inc., has used this technology to create maps and volumetric calculations of several mines in the United States. The information is superior to conventional methods through accuracy, manpower, time, and cost. Holnam, Inc., was the first cement manufacturer to use the Digital Airborne Topographic Imaging System (DATIS?). The technology uses the DATIS? to produce high-resolution terrain maps and volumetric assessments of any area. DATIS? is a mapping instrument that integrates (1) a Light Detection and Ranging (LIDAR) instrument to measure terrain elevation using laser light, (2) a large-format digital camera, (3) a relative position Global Positioning System (GPS) to measure aircraft position, and (4) an Inertial Measurement Unit (IMU) to measure aircraft attitude. The DATIS? can measure up to 220,000 elevation samples per mil. The system continually collects data on the aircraft's position and measures the time for each laser pulse transmission to return from the ground, giving each sample a GPS reference. The system can operate at night, in overcast sky, and during high-wind conditions and can measure terrain below vegetation cover, unlike standard aerial photography used for traditional surveying and mapping. Surveyed ground-control panels are no longer necessary with this new technology, and only one ground GPS base station located within 60 mi from the aircraft position is required. A computer elevation-point data file is created with the x, y, z coordinates of each laser elevation sample. With this file, CAD engineering programs can create topographic maps that rival products using conventional aerial mapping techniques. Volumetric measurements of stockpiles and pits are also available due to the high density of points collected from an area. This new technology radically changes the turnaround time for map users, giving a product in the format used by today's cartographers. The time line from flight to maps is measured in days instead of weeks.

Jan 1, 1999

By J. M. Rios

This paper exposes the reasons that led the Empresa Nacional Minera del Sahara, S.A. (ENMINSA) to the selection of a conveyor belt system for the transport of phosphate rock over a distance of 100 kilometers. ENMINSA was created in 1962, with the main objetive of the exploitation of phosphate rock deposits in the Spanish province of Sahara, in North West Africa. Poor grade outcrops were known previously. A detailed geological research carried over the province led ENMINSA to the discovery of deposits not exposed, and of much higher grade. The sector known as Bu-Craa was chosen as the most promising, and was explored by means of drill holing and shafting. The important amount of information obtained permitted a detailed evaluation of the capacity and grade of the rich ore contained in the Bu-Craa area. Simultaneously with the systematic reconnaissance of the Bu-Craa deposits, ENMINSA developped the study of the technical and economical problems required for the beneficiation of the rock, which comprised five main groups of projects: rock exploitation; beneficiation plant; rock transport from the mine site to the Atlantic coast; storage, handling and loading facilities by the sea- side, and power plant. Once determined the location of the marine loading facilities, which to date are in an advanced stage of construction (figs. 1 and 2), the studies conductive to the selection of the best transport system from the mine to the ocean, along 100 kms. distance were undertaken.

Jan 1, 1968

By Michael F. Jeglic

Dust control methods are practiced throughout the mining industry in order to protect the health and safety of its workers, the integrity of the environment, and to guard against the loss of valuable product. The use of water is often the best and most economical method of controlling dust. Increasingly, chemical agents are being chosen over more traditional mechanical means of controlling dust. Some chemicals are used alone, and many are used to enhance the dust controlling properties of water. This paper describes the various types of chemicals available and their applicability to specific problems encountered by industry.

Jan 1, 1986

By Martin B. Hudson, John Yao, Matthew R. Crow, Yiming Sun, John T. Waggoner, Roozbeh Geraili Mikola

"The Wilshire Grand redevelopment project in downtown Los Angeles includes construction of a new 73-story tower. Construction required excavation up to 93 feet deep (28 m). The south side of the excavation, up to 57 feet deep (17 m), required placement of shoring within about 6 to 10 feet (1.8 to 3.0 m) horizontally away from a 400-foot-long (122 m) section of one of the existing Los Angeles Metro Red Line twin subway tunnels. These tunnels were constructed using a 22-foot-diameter (6.7 m) digger shield, and were initially supported with expanded, precast concrete segments, with final cast-in-place reinforced concrete lining. The temporary shoring system for the deep excavation consisted of soldier piles generally spaced at 8 feet (2.4 m) on center with multiple levels of tieback anchors extending above the subway tunnels. The lowest level of bracing consisted of rakers supporting walers attached to the soldier beams because installation of tieback anchors at that level would conflict with the tunnels. Numerical analyses were performed to predict tunnel movement caused by the excavation and its effects on the train operations. This paper describes the numerical modeling, tunnel and geotechnical instrumentation and monitoring program, and comparison of the computed and observed tunnel responses to the deep excavation and tower construction. With increasing urban redevelopment in major cities, the project is a valuable case history for excavation adjacent to existing tunnels. INTRODUCTION The Wilshire Grand redevelopment project includes the demolition of a 16-story hotel built in the early 1950s and the construction of a new 73-story tower in downtown Los Angeles (LA) that will be the tallest building in the western United States. The project site is situated on approximately 2.7 acres (1.1 Ha) of land bounded by Figueroa Street to the east, Wilshire Boulevard to the north, Francisco Street to the west, and 7th Street to the south (see Figure 1a). The new tower is being constructed by Turner Construction for Hanjin International Corporation. Construction of the basement and foundation of the new tower required excavation up to 93 feet (28 m) deep. Shoring was designed by Cefali & Associates and installed by Malcolm Drilling Company. Along 7th Street, an excavation up to 57 feet (17 m) deep required shoring to be installed within about 6 to 10 feet (1.8 to 3.0 m) horizontally from an existing 400-foot long (122 m) section of one of the LA Metro Red Line subway tunnels (see Figure 1b). The tunnels, extending from the 7th/Metro Station to the Westlake-MacArthur Station, were constructed in the late 1980s and early 1990s with an excavated diameter of approximately 22 feet (6.7 m). They were initially supported with expanded, precast concrete segments with a final cast-in-place reinforced concrete lining. The existing hotel was demolished in 2012 and 2013, with shoring installation and excavation for the new basement occurring as the demolition occurred. At the time of writing, January 2016, the structure of the building adjacent to the tunnels is largely complete."

Jan 1, 2016

By Robert A. Bauer

Two basic types of subsidence occur in Illinois: pit and sag / trough. Pits develop over mines less than 165 feet deep and where relatively incompetent strata are found over the mines. Sag subsidence is found over mines as shallow as 75 feet and more generally over mines of greater depths. The percentage of subsidence and angles of draw associated with sag subsidence appear to be controlled by the rock properties at each specific site. The percentage of subsidence and angles of draw are smaller where the sites are not affected by geologic structures. An investigation to determine if a time factor based on the time interval from the date of mining to the subsidence events has shown that simple correlations with time, percent extraction, average pillar stresses, and pillar dimensions is not evident in Illinois.

Jan 1, 1982

By G. Petrakis

The selection of suitable species of plants for the rehabilitation of mining disturbed lands is one of the most crucial decisions to be made concerning the success of planting revegetation. Native plant species are best suited for use in the work of reintroducing vegetation in rehabilitated areas. By using such species an increase in the success rate of rehabilitation is attained not only as regards yield due to their better growth ability (they are adapted to local climatic conditions), but also because of a better adjustment to and better visual harmonization with the surrounding unspoiled areas.

Jan 1, 2002

By Theodore H. Eyde

The porphyry copper province of the southwestern United States and northern Mexico, is the largest copper producing region in the world. Most of the deposits occur in Arizona which now produces over 54% of the newly mined copper in the United" States. As the many recent discoveries are brought into production, Arizona's share of the nation's copper production will increase. The term "porphyry copper" as used in this paper includes all deposits of generally low grade disseminated copper mineralization amenable to bulk mining techniques. Therefore, copper deposits such as Pima-Mission, Twin Buttes, and Vekol where the copper mineralization occurs principally in the intruded rocks will be considered as "porphyry copper" deposits. Most of the deposits have been discovered since World War II, consequently, the southwest, and particularly southern Arizona is perhaps the most intensively explored area for copper deposits on earth. Most of the major natural resource companies in the United States and Canada maintain exploration offices in southern Arizona. To illustrate the success of exploration efforts, the location of porphyry copper deposits either known or producing prior to World War II are shown on figure 1 and the deposits discovered since World War II which are either in production or in the exploration and development stage are shown on figure 2.

Jan 1, 1973

By F. J. Murrell

No other region of the world is enjoying the tremendous growth of power use that is currently being experienced in Asia. Fortunately for those of us in the coal industry -particularly in Asia -the preponderance of the power plants being planned or under construction designed to use coal as the power plant fuel. This has produced a significant increase in the demand for steam coal, which has in turn encouraged many of us in the industry to develop new coal mines. One country that has enjoyed very substantial growth in coal production is Indonesia. This developing country of 195,000,000 people who live on the nearly 13,000 islands of Indonesia have emerged very quickly to become the third largest exporter of steam coal, following only Australia and South Africa. Almost all coal in Indonesia is mined by surface mining methods. This paper will examine the surface mining of coal in Indonesia, as it continues to be an important part of the supply equation for coal in Asia.

Jan 1, 1996

By D. S. Bird

The Kennecott Utah Copper Modernization Project, initiated in 1986, was directed to provide an expansion and modernization of mining and process facilities at the property's Bingham Canyon Mine and ore concentrators. Major components in the project included installation of an in-pit ore crusher, transfer conveying system, and construction of a new copper ore concentrator with a design capacity basis of 70,000 tonnes/day. The Copperton Concentrator was commissioned in February 1988. A principal feature of the plant is the grinding circuit, comprised of three identical lines, each consisting of a 10.37 m (diameter) by 4.57 m (length) Semi-Autogenous Grinding (SAG) mill and two 5.54 m (diameter) by 8.62 m (length) ball mills. The SAG mills are driven by two variable-speed 9,000 kW DC motors coupled through a clutch-pinion gear-ring gear assembly. The ball mills are driven by 4,125 kW synchronous motors coupled through a typical clutch-pinion gear-ring gear system. The expansion and particularly the Copperton Concentrator performance was so successful that by early 1989, management began examining options to further expand production capacity. With regards to the concentrator, numerous alternatives were considered, ranging from installation of a grinding line similar to one of the existing lines, to a "super" line consisting of a 12.8 meter (diameter) SAG mill and a 20,000 kW motor with a capacity of 50,000 tonnes per day. The technical and economic analysis of the various scenarios indicated that one "large" 11.0 meter (diameter) by 4.88 meter (length) SAG mill with a production capacity of 32,000 tonnes per day and a 12,000 kW drive would be optimum. The key question to be answered in the project was whether to continue with the pinion-ring gear combination, or install a gearless drive. The following paper outlines many of the items that were evaluated in the mill selection process followed by actual plant performance, and a discussion of ongoing plant continuous improvement projects.

Jan 1, 1995