Search Documents

By Karl Gugel, Dante Garcia, Peter Czel, Eduardo Nunez, Joshua Morales, Boris Sullcahuaman

Real-time operational excellence is achieved through the seamless integration of various components. Key aspects include precise instrumentation, real-time data collection, data analytics, and an efficient optimization platform. Additionally, to ensure success, the real-time optimization platform must be incorporated into the site’s internal process control system (Nunez, 2022). This paper provides an overview of practical lessons and best practices for autogenous (AG), semi-autogenous (SAG), and ball mill (BM) grinding. It highlights the implementation of advanced instrumentation, specifically vibration sensors on the rotating mill shell. The paper also delves into the application of advanced analytics necessary for generating new measurements that accurately represent real-time grinding activity in the mill. These Advanced Analytics Measurements (AAM) are compared with well-known grinding curves to determine the optimal grinding point. The discussion focuses on key industry opportunities using real-time mill shell vibration results to derive new correlations and optimize the grinding process.

Feb 1, 2025

By R. E. Snow

The analysis of ground water inflow and discharge from underground mines has received increased attention in recent years due to environmental issues which must be addressed under current state regulations for coal mining and processing operations. In particular, coal operators must assess the probable hydrologic consequences associated with mining activities, and must plan for mine water handling during operation and following completion of mining. The prediction of ground water inflow rates with future mine development allows preparation for potential operational problem and identification of inflow reduction methods. Similarly, evaluation of mine discharge rates is necessary to address potential long-term acid mine drainage (AND) concerns. As part of mine discharge analyses, methods. to control seepage and AMD can be considered. The objective of this paper is to discuss the practical applications of mine inflow and discharge analysis, describe the typical flow components, outline the procedures necessary to perform the analysis, and illustrate the modeling procedures and potential results of mine inflow and discharge predictions.

Jan 1, 1990

By Ravi Sahu

"In the global mining industry, there are those who seem resigned to the fact that the mining industry has always operated according to certain time-tested principles that don’t involve jumping on every new technological trend. Others expect that mines will soon have autonomous electric vehicles running around the clock. The truth lies somewhere in the middle. In business, as in life, that is usually the best path to follow.The instant access to people and information provided by 21st-century technology continues to push businesses in all industries toward greater efficiency and unheard-of levels of modernization. And in the world of mining, the embrace of advanced technology is all about managing risk.However, even in this age of digital information overload, some mine sites still require employees to physically download data from individual trucks to monitor payload data and inspect road conditions using a clipboard. What’s more baffling is that other mine sites still have no way of tracking tons moved at all.This isn’t due to a lack of innovation in the industry. Quite to the contrary, there is an abundance of new technology available that provides real-time monitoring of vehicle movements and tracks road conditions without the intervention of people. So why are owners reluctant to embrace advances in mining tech?Gauging the value of changeSurvey data has traditionally been captured by ground laser scans and LIDAR systems. A mine site surveyor would drive around the pit with a truck-mounted scanner to generate a point cloud. This process would be completed every few days and would take an entire day.The many cons of this method far outweigh the pros. First, it provides no visual data. If an operation has moved beyond the roller wheel and tape measure, visual pit models and LIDAR scans are typically completed once every six to 12 months by an aerial flyover, but such sporadic information gathering isn’t likely to result in the most actionable data. Moreover, given the high cost (in terms of both money and time), the numerous safety and liability issues, and the lack of flexibility in scheduling, manual processes are more trouble than they are worth.Overall, while miners are excellent operators who value innovation, their employers often try to outsource it or acquire innovators instead of investing in existing technology that can improve current operations. It is a never-ending dilemma:"

Jan 5, 2018

By W. Zhang

"The adsorption of collector on bornite has been studied in situ in aqueous solutions by applying an atomic force microscopy (AFM). The AFM images show that xanthate, such as potassium ethyl xanthate (KEX) and potassium amyl xanthate (PAX), adsorbs strongly on bornite mainly in the form of insoluble metal xanthate, which binds strongly with the mineral surface without being removed by flushing with ethanol alcohol. This adsorption mechanism is very similar to the one obtained with chalcocite/xanthate system. However, the result also clearly shows that the adsorption of xanthate on bornite is totally different from its adsorption on chalcopyrite, during which oily dixanthogen is the main adsorption product on chalcopyrite surface. The obtained AFM images also showed that the adsorption increases with increasing the collector’s concentration. When Cytec Aerofloat 238, a dialkyl dithiophosphate collector, is used, it adsorb on bornite mainly in the form of an oily substance, which can be rinsed off mineral surface by flushing with ethanol alcohol. AFM images also show that the adsorption of Cytec Aerofloat 238 increases with increasing the adsorption time. INTRODUCTION The adsorption of collector on mineral surface is vital for a successful flotation process to achieve a satisfying recovery. Historically, many works have been carried out to clarify the adsorption mechanism of collectors on sulfides. (Gaudin and Schuhmann, 1936, Poling and Leja, 1963; Allison et al., 1972, Fuerstenau, 1982; Leja, 1982; Woods, 1984) Compared to other copper minerals such as chalcopyrite and chalcocite, much less work has been done to study the adsorption collector on bornite. Allison et al. (1972) studied the reaction products of various sulfide minerals with xanthate solutions and reported that the measured rest potential of bornite in 6.25×10-4 M KEX solution at pH 7 was +60 mV and the reaction product of PAX on bornite was cuprous alkyl xanthate. Mielczarski and Suoninen (1984a, 1984b) applied the XPS and studied the adsorption of potassium ethyl xanthate on cuprous sulfide. It was reported that there was a relatively rapid formation of a well-oriented monolayer of xanthate ions followed by a slow growth of disordered cuprous xanthate molecules on top of this layer. Buckley et al. (1984) investigated the surface oxidation of bornite by linear potential sweep voltammetry and X-ray Photoelectron Spectroscopy and proposed the adsorption products on bornite depended on the solution potential. Zachwieja et al. (1987) studied the electrochemical flotation of the bornite-ethylxanthate system and reported that KEX reacted with bornite through an electrochemical oxidation reaction forming cuprous xanthate between -0.4 and -0.2v (SCE). Hangone et al. (2005) studied the flotation of a bornite-rich copper sulfide ore using thio collectors and their mixtures and reported that the highest copper recoveries were obtained with the diethyl dithiophosphate (di C2-DTP)."

Jan 1, 2016

By E. D. Goddard

There are similarities, and differences, in the surfactants used in cosmetics and detergents. In both applications anionic surfactants constitute the major category. Their main function is to clean, i.e. remove grease and particulate matter from fibrous or hard surface substrates. Cationic surfactants are used for conditioning substrates. Nonionic surfactants can function as a substrate cleanser but are seldom used as such in cosmetics; however, selected non-ionics are often employed as a primary emulsifier. Several specialized nonionic surfactants are used as a secondary surfactant in formulations to promote foaming and emulsification. Specific examples and modes of action of surfactants will be presented.

Jan 1, 1988

By X. Nie

A new one-step process was developed to completely eliminate iron and directly obtain pure Ni, Co, and Cu chloride catholyte from nickel rich matte by low temperature (400 0c) chlorination roasting of Ni, Co, and Cu with HCl and leaching with water (PH 7). The effects of roasting temperature, time, oxygen potential and HCI addition and leaching temperature, pH, H2S04 addition and residue sulphur on the recovery of metals and purity of leaching solution were investigated. More than 99 % of Ni and Co and 95 % of Cu in the matte was directly extracted into the solution while 99.995 % of Fe remained in the residue. The iron concentration in the leaching solution was less than 3.6 X 10-5 mol/L.

Jan 1, 1994

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By J. Iannicelli

Spray drying is the principal drying method used in the production of over six million tons annually of beneficiated kaolin in Georgia. Thirty-three dryers in the Georgia Kaolin belt comprise the highest concentration of large tonnage spray dryers in the world. The steady growth of spray drying in the U.S. kaolin industry is paced by advances in design and development of large spray dryers which have led to large scale new applications in mining and related industries.

Jan 1, 1982

By A. G. Belova

With the federal climate change legislation in progress, there is a need for demonstration-stage technologies aimed at providing clean energy from coal. Our research aims to experimentally illustrate the feasibility of capturing CO2 on a novel sorbent system from a gaseous stream. The gas is then released resulting in a regenerated sorbent and a pressurized stream of pure CO2 to be used for storage. The proposed sorbent is a ceramic honey-comb structured monolith coated with CaO supported on a high-surface area alumina. CaO is a natural acceptor of CO2 and our design ensures the physical stability and chemical reactivity of CaO over a large number of CO2 capture/release cycles. Furthermore, the use of the monolith ensures a uniform flow through the reactor, minimizes pressure drop across the reactor, and maximizes the surface reactive area. In this paper, we will present the results from a flow-through laboratory-scale reactor that establishes the efficiency of the proposed system to capture CO2. Future applications of the reactor include integration within the new-generation coal gasification power plants, such as IGGC, as means of providing decarbonized electricity.

Jan 1, 2010

By Bernard Scheiner

A number of wells were drilled at two phosphogypsum stacks, one at P-21 owned by IMC and the other at Agrico's South Pierce Stack. Each well was sampled, and composites representing 5-ft increments were leached with synthetic rainwater to determine the extent of metal and nonmetal migration. To simulate what was occurring in the stack, composite samples were placed in a column, so that the column represented the stack in miniature form. Leaching experiments showed that both metals and nonmetals moved down the column when water was added to the top of the column. Data obtained from P-21 showed that with time the concentration of metals and nonmetals reached equilibrium values. The concentration of Ca, SO4, F, Si, and PO4 were -600 ppm,~1,500 ppm, 32 ppm, 14 ppm, and 22 ppm, respectively. Column leaching of South Pierce material, representing 0 to 55 ft of stack, showed that after 355 in. of water, the stack was near equilibrium values down to the 33-ft level. With continued addition of water, the portion of the stack at equilibrium would continue to increase and eventually reach the values observed for P-21. The test showed that the sulfate concentration of the effluent from the stack would never reach the USEPA standard value of 250 ppm. During the leaching test, it was determined that the permeability of the phosphogypsum in the columns was 0.000103 cm/sec. This number was used in the modeling. The data obtained from the leaching experiments cast some doubt on the practice of entombment now being practiced for closure of phosphogypsum stacks. The data clearly shows that with time, the amount of material leaching from the stack is low in concentration, with only the calcium and sulfate at higher levels. When a stack is closed at an existing operating plant, allowing rainwater to fall on the stack and capturing the solution in the existing pond system would eliminate the need for covering the stack, since with time the closed stack would continue to leach and at some point reach the equilibrium values of the P-21 stack. Entombment means that the leachable material in the stack will always be there and will require monitoring forever. Allowing rainwater to decontaminate the stack may be the best environmental solution to the problem.

Jan 1, 1999

By F. Montgomery Lyon

Pyritic sulfur in coal occurs as discrete mineral particles, and its liberation and physical rejection is the primary target for coal desulfurization. An acceptable solution to the pyrite removal problem from fine coal is not found in the standard methods of coal cleaning such as jigging, heavy-medium separation, tabling, and hydro-cycloning. Although fine coal is an ideal size for froth flotation, this method, as currently practiced is also unsuitable as the fine pyrite usually floats with the coal. One possible solution to this problem may be the froth flotation of pyrite from coal. This reverse flotation scheme would have the major advantage of removing both free pyrite and locked pyrite-coal combinations. With this possibility in mind, we have, as a first step, compared the flotation and adsorption. characteristics of an ore-pyrite and coal-pyrite with potassium-ethyl-xanthate as a collector 1 Related Research. The action of ethyl-xanthate on coal has been studied 2 by Horsley. He measured the contact angles of coal in distilled water and in the presence of purified ethyl-xanthate. The results indicated that the xanthate was not adsorbed by the coal. Additional contact angle data were obtained to determine the effects of cupric, ferric, and ferrous salts on the system. Then either the ferric or cupric salts were in, solution with the xanthate, there was an increase in the natural contact angles of the coal. This indicated that these heavy metal ions activated the flotation of the coal with xanthate. However, ferrous iron did not act as an activator. Horsley stated that the most attractive explanation was that the xanthate is oxidized to dixanthogen in the presence of the ferric and cupric ions.

Jan 1, 1971

By H. G. Schoenike

A subsequent spin off of the energy shortage is the new life for barite. Over 90% of the barite produced in the world is used as a weighting material in oil well drilling muds. Business is booming; the price of barite has risen; scarcity is imminent, and exploration is going full steam ahead. New barite-producing companies are being formed and many of the barite consumers are considering becoming producers. Prospectors have found a new "love," smaller deposits are being explored, and old deposits, previously rejected, are getting a reappraisal. Even barite tailing piles are being resampled.

Jan 1, 1980

By K. Severin, B. Flanigan, P. Marion

"Plutonic-related" gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As- (Sb-Hg) are a good empirical indicator of the depth of emplacement and distance from causative pluton. These associations have been used successfully in exploration. Results from several analytical techniques also suggest a phenomenological cause for these metal associations. Gold and bismuth have paired mineralogy at high temperatures and, thus, are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2003

By E. D. Attanasi, M. W. Bultman

Most statistical measures of mineral exploration continued downward in 1986. Prospects in 1987, however, appear to have brightened for exploration as the overall economic health of the mineral industry improved. The Society of Economic Geologists (SEG) survey of US and Canadian firms documents the marked decline in US mineral exploration since the early 1980's. From 1981 through 1986, the total exploration expenditure by US firms declined by more than 73% (Fig. 1). Exploration expenditures by US firms declined by 66%%. US based professional exploration staffs were slashed by 70% (Fig. 2). Also, many firms have written off some reserves because of weak markets or have not delineated new reserves to replace production. The Canadian government reported that between 1981 and 1986 Canadian molybdenum re¬serves had declined by 30%, lead and zinc reserves by 20%, and nickel and copper reserves by 15%. The SEG survey also shows the immediate impact of the decline in the dollar on US exploration expenditures abroad. Between 1981 and 1986 the share of the exploration dollar spent by US firms outside of the country declined by nearly one-half and exploration acreage abroad declined by 69%. The downward trend of the last six years may finally be near the end as a leaner and more efficient minerals industry starts to gear up for a period of increased activity. An industry survey reported to Mine Development Bimonthly (Metals Economics Group) indicates that mining firms were expected to increase exploration expenditures in 1987 by at least 10% above 1986 levels. Worldwide expenditures for 1987 by companies covered by the report were expected to top $800 million. It is the first time since 1984 that an increase in exploration expenditures was expected. Also, the US Bureau of Land Management reported a 30% increase in new mining claims for fiscal year 1987 over fiscal year 1986. The bulk of the increase in claims was in states having intense gold exploration, particularly Washington and Oregon. Much of the optimism is undoubtedly due to the increases in metal prices that occurred in 1987. Some of these increases include gold, average price up about 20%; copper, average price up 24%; aluminum, average price up 26%; and nickel, average spot price up 20%. The SEG survey shows precious and base metals accounting for 89% of the exploration expenditures in the US in 1986, up 52% from 1981. The US Bureau of Mines estimates that 80% of US exploration activity in 1986 was directed entirely at gold (1986 Minerals Yearbook). Worldwide exploration plans indicate the continued dominance of gold exploration. New programs were announced for Ghana, Malaysia, and Indonesia. Major new exploration programs were also launched for lead-zinc sulfides in Morocco, platinum and palladium in northwest Brazil, rare earth minerals in Greenland, diamonds in Indonesia, and heavy minerals off-shore Australia. Significant gold discoveries were made at Angels Camp in Oregon; South Africa, near Potchestroom; India, in the Chitradgra district; Northern Ireland near Mt. Speerin; Chile, San Cris-

Jan 5, 1988

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By Douglas B. Silver

Study Parameters (Status as of February 1993) Time Period: 1989 -1991 151 North American Public Metal Mining Companies Fiscal not calendar year basis 85+% of Canadian and U.S. Metal Production Au, Ag, Cu, Pb, Zn, Mo, Ni, W Results are Preliminary and Research Continues Chicken Little is Alive and Well

Jan 1, 1993

By Harvey P. Knudsen

This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima Nine, located near Tucson, Arizona. Results at the Pima Mine indicate that the geostatistical method is no better nor worse in predicting block grades and total tonnage than the ELIP or IDS methods in contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELlP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties, the geostatistical model is more attractive, due to its ability to construct confidence limits on the estimates.

Jan 1, 1976

By G. R. Brunskill

The molybdenite flotation plant at Magma Copper Company, San Manuel concentrator has been in operation since 1956. In January of 1980 the plant was converted from a hydrogen peroxide - ferrocyanide process to the current sodium cyanide - sodium hydrosulfide process. This paper is an operational review of Magma Copper Company's molybdenite recovery circuit, column cell flotation experience and use of on- stream x-ray flourescence analysis.

Jan 1, 1985

By D. Collins, J. Winfield, V. Gangrade, B. Slaker, S. Braganza

"Researchers at the National Institute for Occupational Safety and Health (NIOSH) are investigating the unique pillar stability issues associated with room-and-pillar mining in dipping underground stone mines. The objective of this paper is to study the post-blast impact in and around a pillar, using microseismic monitoring. To accomplish this, a microseismic monitoring system has been installed at a dipping underground stone mine in central Pennsylvania. The microseismic system is comprised of 18 uniaxial accelerometers; 12 sensors are installed in a single pillar and 6 sensors are installed in the surrounding area. More than 4,400 microseismic events have been located near the study pillar following the blasts. The number of triggers increased significantly following the blast, and the trigger rate in the first five minutes was 60 triggers per minute and three triggers per minute over the next three hours. The processing of high-quality triggers indicated a large number of low magnitude microseismic events near the blasting face. The event locations were identified more accurately by using a 3D-velocity model, with an average 9 m expected location accuracy for this array calculated using the system data. Seismicity was absent from the core of the pillar, but significant numbers of events were found following cutter roof along a crosscut as it was developed as well as in the location of a rib failure event. Additionally, the events were located in the roof, showing high number of microseismic events within 0–10 m of the roof line compared to 10–30 m above the roof line.INTRODUCTIONGround control stability is essential to any mining operation for ensuring mineworker safety and health and preventing catastrophic failures of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted research in stone pillar design and has established fundamental pillar design guidelines for the underground stone industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2018). However, the data that makes up the S-Pillar database consists of shallow depth, flat-lying, single-level mining operations. Therefore, to expand this dataset and to develop guidelines for challenging conditions such as dipping and multi-level mines, NIOSH is currently conducting detailed pillar response investigations at mines with these characteristics. The study is being conducted using multiple research approaches, including seismic modeling and tomography, numerical modeling (Sears et al., 2019), stress monitoring, and LiDAR-based laser scanning (Slaker, Murphy, and Winfield, 2019). This paper discusses the findings from the microseismic monitoring system installed at the Pleasant Gap Mine, a steeply dipping underground limestone mine in central Pennsylvania."

Jan 1, 2019