Search Documents

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By John M. Arnold

Several years ago it became apparent to some of our people that; there was developing a very definite need for largee coal reserves in the West to satisfy- the need for fuel for the furnaces of electric generating plants with the rapid development of, the West, of both population and industry, it was impossible for hydro-electrics plants to keep up with the ever increasing demand for electricity. In 1960, Mr. E. R. Phelps, then associated with the engineering department of Peabody Coal Company, began a search for and development of coal deposits in the very remote northeast section of Arizona near the village of Kayenta. Travel to this section of the country was not easy even at this late date, and it was an eight hour drive from Farmington, New Mexico to Kayenta, Arizona, a distance of some 130 miles. The trip was over roads that even' a-horse and wagon had trouble negotiating and a four wheel drive vehicle was about the only type of transportation that could satisfactorily traverse these roads, as testify many badly beaten sedans and coupes that tried it. Since that time a very excellent road has been constructed from Shiprock; New Mexico to Cameron, Arizona where it junctions with another excellent road that runs north to Page, Arizona and the Lake. Powell area and south to Flagstaff, Arizona on highway 66. Kayenta is a small village nestled at the foot of the Black Mesa near its northeast extremities. The coal deposits of interest were on the surface of the mesa. This location presented another problem, as the only trail to the top of the mesa was intended for walking, horseback, or a brave soul In a horse and wagon. Once again the four wheel drive vehicle was about the only answer. To reach the coal deposits you must climb the mesa, which is vertical ascent of some 1,500 feet, and then proceed southward into the bowl of the mesa with an ensuing descent of some 1,000 feet, finally coming to an elevation of 6,500 feet, at which elevation the coal outcrops become apparent.

Jan 1, 1969

By Stephen Njoloma, William Bracken, Harald Cordes, Ivan Hee

"DC Water’s First Street Tunnel (FST) is part of the $2.6 billion Clean Rivers Project designed to reduce the occurrence of combined sewer overflows into local waterways. Due to flood events in the Bloomingdale and LeDroit Park neighborhoods, the FST Project was accelerated by DC Water to mitigate future flooding by boosting storage capacity and thus relieving the undersized combined sewers.The FST Project was finalized in 2016 as a collaborative effort between DC Water, its consulting team consisting of Greeley & Hansen and McMillen Jacobs Associates, and the design-build team of Skanska, Jay Dee Contractors (SKJD) with WSP Parsons Brinckerhoff as the designer.Scope of project. The FST Project (Fig. 1) included four primary shaft sites, a large 6 m (20 ft) internal diameter, 823- m (2,700-ft) long bored tunnel and three adit connections from the off-line shafts to the large-diameter tunnel. The adits which vary in size and length, are the subject of this article. The Channing Street site (Fig. 2) was established as the main site for an Earth pressure balance tunnel boring machine (TBM) and included a 49-m (160-ft) deep shaft with slurry wall support of excavation and 20-m (65-ft) internal diameter final cast-in-place permanent concrete liner. The construction sites at Adams Street, V Street and Thomas Street each consisted of off-line shaft structures tied to near-surface sewer diversion chambers and ventilation facilities. These three off-line shafts were connected to the large bored TBM tunnel via adit tunnels. Each of the three adits had a portion or the entire length excavated by sequential excavation method (SEM) in frozen ground.The Adams Street adit (Fig. 3) was constructed in two phases. The first phase is the 23-m (75-ft) long and 5-m (16-ft) diameter section immediately outside the drop shaft which also serves as the deaeration chamber and was excavated by SEM. The second phase which is 91 m (300 ft) long and 3 m (10 ft) in diameter was excavated by Micro TBM (MTBM) launched from within the permanently lined deaeration chamber. MTBM excavation commenced toward a reception chamber that was excavated by SEM from the previously bored FST TBM tunnel. This SEM excavation had a 5 m (17 ft) diameter and a length of 4.5 m (15 ft)"

Jan 3, 2018

By N. W. Stump

New developments in on-stream analysis using immersed radioisotope gauges including results from plant installations are described. The control of grinding and flotation using a small digital computer has been complemented by this development. A control scheme for grinding which is based on maximum throughput at constant product size and preliminary work in flotation control are also outlined.

Jan 1, 1974

By M. I. Brittan

A technique has been developed that analyzes routine mill operating data to determine the key operating parameters responsible for gold losses to tails. These parameters represent the prime operating variables having a dominant effect on gold recovery. The technique quantifies these effects for the specific plant being analyzed, providing a tool to optimize recovery and costs and so enhance the mine?s cash flow. The quantitative relationships generated will be different for each ore and plant: every case is site-specific and has to be treated on its merits. Examples are provided to illustrate the considerable metallurgical and financial benefits which can be realized from optimization. The examples are taken from case studies of mills in four major gold mining districts of the world.

Jan 1, 2010

By M. Karmis

Subsidence planning and control must be an integral part of mine design in order to minimize the economic impact of underground mining on the surface. Pre-calculation of surface deformations which may cause damage to surface structures must be performed and dam-age criteria must be established, if the response of structures to such movements is to be determined and the extent of damages to be assessed. In this paper the Surface Deformation Prediction System (S.D.P.S.), which can be used to predict accurately the vertical and horizontal parameters of surface movements due to underground mining, is discussed. The Subsidence Response Modeling Program (S.R.M.P.). which can be applied to evaluate the response of buildings to subsidence-induced movements, is also reviewed. Finally, an example is presented demonstrating the applicability of these techniques for subsidence design and control.

Jan 1, 1990

By B. Anamaeric

Economic, environmental and operational disadvantages of the traditional blast furnace process has led to the development of direct smelting reduction processes, including those that utilize self reducing/ fluxing dried greenballs as iron oxide feed materials. This is mainly due to improved carbothermic reduction, carburization and reaction kinetics. In this paper, the morphological changes of the greenballs as they transform to pig iron nuggets are examined over time at a constant temperature of 1,400° C. The products produced after each treatment were characterized using optical microscopy, scanning electron microscopy/energy dispersive spectroscopy and point counting/image analysis. The changes in the percent metallized area, wustite dendrite and slag matrix content of the structures were calculated. It was determined that the transformations were initially controlled by dissolving and containment of iron oxides in the molten slag and their consequent reduction to iron, followed by coalescence of the metallized areas. The final transformations were controlled by the carburization of the metallized areas.

Good morning ladies and gentlemen of the AIME. I was doubly pleased when Toby Yu asked me to present to you my thoughts on the past, the present, and the future of bulk transportation by barge. My first pleasure comes from sharing with you the subject that has been my career for many years. I love this industry in the same way Mark Twain loved our rivers. Somehow, I can find in all of the activities that make up this crazy barge business the same sort of excitement that he found in "steam boating." The second reason for my enthusiasm is that Toby carefully pointed out that the presentation had to be kept to a maximum of 15 minutes. I can promise you that I will hold to his maximum time limit.

Jan 1, 1982

By Randall Smith, Leslie Stayner

At the request of the Mine Safety and Health Administration, a quantitative assessment of the risk of lung cancer associated with occupational exposures to diesel exhaust was performed. This assessment was primarily based upon the results from a study of the effects of chronic inhalation exposure to diesel exhaust in Fischer-344 rats (previously reported by Mauderly et al., 1987). An adaptation of the Armitage-Doll multistage model, which allows for an age-dependent effect of exposure, was used to model the tumor response data. This model was fitted to all tumors (benign and malignant), and to malignant neoplasms alone. Estimates of unit risk (potency) were derived based upon a linear approximation to the results from the multistage model. A biologically equivalent dose was developed to scale the results from airborne exposure in rats to humans, which was adjusted for differences in weight, ventilation rate, deposition fraction, and the percentage of time actually exposed. Comparisons are made with risk estimates derived from modeling other rat inhalation bioassays and from applying different models to the study by Mauderly et al. (1987). We emphasize that our risk estimates are based upon a series of assumptions and carry a great deal of uncertainty. In particular, uncertainties regarding the effects of exposure on lung clearance mechanisms, the deposition rates in humans, and the relevance of our exposure index limit our confidence in these risk estimates. Because of these uncertainties, this risk assessment would best be viewed as an exploratory effort. Key words: Diesel, lung cancer, risk assessment

Jan 1, 1991

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968

By H. Colijn

The problem of the freezing of moist raw materials, such as concentrates, in railroad cars during winter shipment has been a continuing source of both economic and operational trouble to the industry and to the railroad companies. The difficulties center around the discharging of frozen cargoes into the plant materials handling system. Because of cargo freezing, appreciable delays in car-dumping schedules occur each winter and cause additional expense for demurrage charges and for slowdown of plant operations. In one plant during one winter, a car dumper rated at 40 cars per day could dump only 3 cars per day in bad weather. Delays became so serious one winter, that 500 cars held in the yard became so badly frozen, that they were sent to the southern part of the United States to thaw after they accumulated an average of two months demurrage charges. These delays in car unloading become critical if unit or integral train concept is applied to the movement of raw materials. Anticipated savings in transportation costs through better equipment utilization are largely based on rapid loading and unloading cycles of whole trainloads. If freezing problems cannot be adequately solved, unit train operations cannot be operated to achieve the potentially large reductions in transportation costs. The freezing problem may tend to become even greater in the years ahead, because the unit train concept will allow the trains to run faster and consequently the heat loss will be accelerated due to the larger heat transfer coefficient. A compensating factor, however, will be the shorter travel time. Further, the sources of raw materials being mined are located farther north than before and the ambient temperatures during transit are going to be lower.

Jan 1, 1976

By T. F. Torries

The primary merit criteria used by the mining industry is internal rate of return (IRR) rather than net present value (NPV) although NPV is favored by academicians. This paper discusses the problems with IRR and NPV and compares the multi-goal nature of decision makers and their need for information with the characteristics of NPV and IRR. Conclusions are that both NPV and IRR are needed for investment ranking, that NPV suffers the same multiple root problem as does IR.R, and the determination of incremental IRR to reach NPV consistent project ranking is misguided in practice.

Jan 1, 1997

By K. H. McDaniel

People are our most valuable resource. It is as true today as any point in mining history as we face unprecedented personnel shortages aggravated by a workforce that is aging, significant generational gaps and difficulties recruiting younger professionals all amidst increasing global mineral demand. The educational system has a similar, but slightly contrary problem. Many historically strong mining engineering programs have died. Now, fewer mining oriented universities are trying to produce more students in order to meet the demand. Moreover, their situation is aggravated by a similarly aging workforce, a general lack of mid-career PhD?s with the interest and field experience to teach effectively, an extremely slow hiring and funding process, and an inability to be competitive against private industry compensation packages. The traditional instructional model, while not necessarily broken, is most certainly dated, and can penalize programs and students where schools do not have in-house expertise in a given topic. Mining companies, like Rio Tinto, have the opportunity, if not necessarily the obligation, to positively influence how this model works. Educational Partnerships may be the key. This paper will address some observations, and possibilities, associated with Rio Tinto?s efforts in this area.

Feb 23, 2014

By T. Rudolph, M. Pawlik, J. Benndorf, X. Yin, J. F. Brune, P. Goerke-Mallet

The long and often undefined period in the post-mining phase challenges geo-monitoring with its various responsibilities, like the detection of environmental changes, ground movements and water management. Modern methods of geo- and environmental monitoring observe numerous aspects using active and passive sensors with multispectral, hyperspectral and microwave sensors, with diverse spatial dimensions and spatiotemporal resolutions from satellites, Unmanned Aerial Vehicles (UAVs), in-situ sensors. Data integration, together with on-site knowledge and experience, provides the basis for comprehensive modeling, which improves the understanding of the environmental changes and their related causes, which is an essential step for public acceptance. In this paper, we aim to give a brief overview of various geo- and environmental monitoring methods.

Mar 2, 2022

By H. Ankara

Determining the identicalness levels of the same model trucks working in open pit mine transportation system by means of statistical analysis methods is very significant in terms of availability analysis. In this study, the identicalness levels of two trucks picked randomly from the 170-short-tonne truck fleet working in open pit coal mine over one-year period were examined through a non-parametric test, Mann-Whitney U test for two samples. Time to failures (TTFs) and Time to Repairs (TTRs) of the trucks were analyzed with this test technique and then whether they were identical or not was determined. In order to determine whether the trucks identified to be identical at the end of this test displayed the same mining performances within the same open pit transportation system, the availability analysis of the identical trucks was carried out. As a result of the availability analysis, it was observed that the trucks had availability values that were very close to each other. It was also determined that Mann-Whitney U test could be employed together with availability analysis. Finally, it was observed that Mann-Whitney U test for two samples could yield rapid results in the performance analysis of complex systems like open pit mines.

Jan 1, 2010

By M. J. Hart

Today, aggregate producers in the Denver Metropolitan area, herein defined as Denver and surrounding communities in Adams, Arapahoe, Boulder, Douglas and Jefferson Counties, are scrambling to secure their future reserves. The Denver market is somewhat unique among the larger metropolitan markets in that the source of needed aggregate for the future is very much undecided. 2. Present Aggregate Resources Presently, the annual consumption of aggregate resources in the Denver Metropolitan area amounts to approximately 16 million tons of sand, gravel and crushed stone of which the later accounts for about 20%. Based on population growth projections for the front range, by the year 2000 the annual rate of consumption for aggregate in the Denver Metro area could be in the 25+ million ton range.

Jan 1, 1987

By Reed J. Irvine

One normally does not find sudden and dramatic changes in the investment climate, barring the unexpected outbreak of-wars or revolutions. Asia has seen a fair amount of military action and revolt during the past year, not all of it unexpected There was the fighting in Laos, which resulted in the as yet unconcluded negotiations which will probably lead to the establishment of a neutralist regime. In April of 1961 another revolution occurred in South Korea, and the elected government was replaced by a military dictatorship.. Communist guerrilla activity in South Vietnam was stepped up, and uncertainty about the future of that area increased. Relations between Pakistan and Afghanistan became more strained, and while no fighting has broken out, diplomatic relations between the two countries were broken off. India was both the victim of further incursions of her territory by communist China and the perpetrator of the forcible seizure of territory from Portugal. Indonesia has been making preparations for an armed attack on the Dutch in New Guinea.

Jan 1, 1962

By Odin Wilhelmy

Agriculture in the United States today is becoming more and more a business, rather than a way of life. In the light of this, it behooves the farm-supply industries that provide the American farmer with his tools of production--feed, fertilizer, machinery, and the like--to give even greater attention than they have in the past to meeting the needs of the farmer-businessmen they are serving. Increasing competition among the companies that make up these industries merely accentuates this need for better service. An opportunity for such improved service, not yet fully realized, exists in the fertilizer industry today. That opportunity lies in the increased transportation of fertilizer ingredients by water. However, before the benefits inherent in this increased water movement of fertilizers can be fully realized, certain obstacles must be met and overcome. It is the purpose of this paper to outline the nature and magnitude of this opportunity, to point out some of the roadblocks and the steps that can be, or are being, taken to remove them, and to indicate some of the rewards that would logically stem from success in these efforts.

Jan 1, 1961

By L. A. Khan

This paper first discusses the physicochemical cleaning methods used to process fines followed by an analysis of the subprocesses of froth flotation and the adverse effects of slimes and particle oxidation. These subprocesses include the phenomena of interception, contact, adhesion and levitation. Preventive and corrective measures to combat the generation of fines and their effects are suggested. Preventive measures include controlled grinding, limited liberation, flotation at coarser sizes. Means of preventing oxidation and/or removing oxidation products are a1 so discussed. Corrective measure to increase recovery include intensive aeration, aggregation of particles, intensive mixing, increased retention time, and reduction of detachment. Measures leading to improves selectivity involve means to reduce slime coating, achieve selective mineralization of bubbles and minimize entrapment.

Jan 1, 1986

By G. J. Gersbach

The Robe River Iron Ore Project began in 1962 when Cliffs International acquired mining leases in Western Australia's Pilbara Region. Initial reserves were proven and bulk ore samples sent to the U.S.A. for pilot plant testwork. Cliffs Western Australian Mining Company Pty. Limited (30%) manages the project in joint venture with Mitsui Iron Ore Development Pty. Limited (30%), Robe River Limited (35%) and Cape Lambert Iron Associates (5%).

Jan 1, 1983