Search Documents

By Frank E. McCall, John K. Marshal, Fred Garcia

Since the advent of longwall mining systems in the United States, mine operators are increasingly relying on methane drainage techniques to supplement the ventilation system. The most commonly used technique is the vertical gob borehole. The number and spacing of vertical gob boreholes per panel is generally based on experience and underground conditions. To design a more efficient methane drainage systems, mine operators must accurately determine methane gas produced. Thus, mine operators must monitor gas flow and methane gas concentration on every vertical gob borehole on active panels at least once or twice during each 8-hr shift. As the mine grows, it is possible to have more than one operating longwall and many vertical gob boreholes. Thus, daily visits to each vertical gob borehole site can become very time consuming. During weekends when methane gas concentrations typically drop because there is no mining activity, borehole sites may not be visited. To obtain accurate gas flow data, a gob borehole monitoring system was designed and constructed by the U.S. Bureau of Mines (USBM). Gas flow, methane gas concentration, gas temperature, barometric pressure, and vacuum pressure of the exhaust fan are the parameters collected by the system. The system also includes circuitry for automatic shutdown of the exhaust fan and an alarm system before an unsafe condition is created. Telemetry components were also integrated into the system to allow for transmission of borehole data to the mine office. As a test, the system was installed and operated on a vertical gob borehole for six months. Test results indicated that intermittent measurements with hand-held instruments from vertical gob boreholes were always higher than gas flows measurements made by the gob gas analyzer system. This paper describes the system components, operational characteristics, and the results of the test program.

Jan 1, 1995

By T. Guler

Turkey has important celestite reserves in Sivas. These reserves have gypsum and/or calcite as gangue minerals. Celestite-calcite ore cannot be concentrated by gravity methods due to the low efficiency of gravity methods in fine sizes. Research was tried to concentrate celestite to a market grade by flotation. Parameters such as pH, particle size, dosage and types of collector and depressant were examined. Cyanamid A-845 and Na-oleate combination as collector, sodium silicate as depressant, and Aerofroth-65 as frother were found as the optimum flotation reagents. By applying 3-stage cleaning, a concentrate assaying 95,34 % SrS04 was obtained with 84,93 % recovery.

Jan 1, 1999

By B. J. I. Adair, K. R. Weller

The bulk scavenger tailing from Aberfoyle's Hellyer Concentrator, which represents about one-third of the total tailing, runs about 2.5-3 g/t gold and 140-200 g/f silver. Both values are very finely disseminated, particularly the gold. Aberfoyle wished to establish whether ultra-fine grinding followed directly by cyanide leaching could be applied to the tailing for recovery of gold and silver. The work comprised the determination of gold and silver recoveries as a function of grind size and leaching time, the specific energy consumption required for continuous wet grinding of the tailing to the specified product size in a small horizontal continuous stirred mill, and an estimate of the rate of media consumption. The maximum extraction of gold, 23.3% was obtained from the finest product, with the highest cyanide concentration and longest leach time, confirming earlier work. A similar result was obtained for silver. The specific energy requirement for milling rose from 27.7 kWh/t for a P80 of 8.1 um to 219 kWh/t for a Pea of 2.3 um. The consumption of ceramic media was about 1.6 g/kg of final product. An extensive QEM'SEM Trace Mineral Search on the unground tailing failed to identify any gold-bearing particles but did identify silver-bearing particles which displayed a variety of textural associations and liberation characteristics.

Jan 1, 1998

By Menglong Bian, Xiaotong Dong

Thermal damage is an urgent problem faced by deep mining. High-temperature rock mass, hot water and electromechanical equipment are the sources of the thermal damage. The increase in air temperature in mine tunnel is the result of fluid–solid coupling heat transfer from various heat sources. This paper takes a roadway with hot water and a mine car as the research object. Based on the Fluent, Static Structural and Steady-State Thermal modules in ANSYS, the thermal-fluid–structure coupling analysis in the roadway is carried out. It is found that the hot water has a significant effect on the thermal environment of the mine. Under the experimental parameters, the maximum heat flux density and equivalent elastic strain at the interface between the hot water and the rock are 9789.3 W/m2 and 0.00054532 m/m, respectively. The heat flux distribution in the rock area near the mine car does not change much, and the equivalent elastic strain value in this area is high. After the air is heated in the hot water area, the temperature curve changes gradually and then rises steadily. By changing the inlet air temperature parameter, it is found that the lower the inlet air temperature, the better the cooling effect, and the change of the inlet air temperature can change the air temperature field in the roadway as a whole. By changing the parameter of inlet air speed, it is found that higher wind speed brings better cooling effect, but with the increase in wind speed, the cooling effect of roadway thermal environment is very limited. When the wind speed increases from 5 m/s to 10 m/s, the air temperature of most measuring points drops by more than 2℃; when the wind speed increases from 15 m/s to 20 m/s, the air temperature of most measuring points drops below 0.7℃. After the wind speed reaches a certain value, the cooling effect of ventilation is very limited.

May 5, 2022

By Wenjun Ju, Xiaodong Sun, Jianwei Zheng, Bingding Yi, Zhaorui Ma, Pengfei Jiang, Lingfu Zhu, Yangfa Zheng

The presence of hard roof poses a significant threat to the safety of underground coal mining. In this study, a mechanical model is established for underground stopes to analyze the overburden structure with the advancing of the mining face. It is indicated that the load-bearing arch structure (LBAS) is formed above the stope for roofs with regular hardness, whereas the reversed-basin bearing structure (RBBS) is formed for hard roofs. Compared with the LBAS, the RBBS can induce an additional pressure at the foot of the bearing structure, and this effect becomes less as the distance between the hard roof and stope increases. The ultra-deep borehole hydro-fracturing technique (UHT) is proposed to weaken the hard roof for pressure release, and the associated equipment and procedures are also presented. The UHT is based on horizontal drilling along the axial direction of the roadway in the roof, and then the receding segmented hydraulic fracturing technique is used to achieve the purpose of fracturing (weakening) of the surrounding rocks. Field tests are carried out in 3022 roadway of Daliangwan coal mine in Yulin to assess the developed technique, equipment, and fracturing procedures. To evaluate the fracturing effect, deep borehole stress-meters are installed at different depths of the fractured and un-fractured zones of the roadway, along with hydraulic support pressure sensors placed at the mining face. The results show that compared with the un-fractured zone, the pressure on the wall and pillar sides is lower than that in the fractured zone, and the associated weighting duration and weighting area ratio of the fractured are reduced by 53.23% and 33.59%, respectively. This indicates that the presented UHT can provide a new solution for the prevention and control of mining disasters induced by hard roof failures in underground coal mining.

Nov 2, 2020

By Liaqat Ali, Robert Chapman, Asghar Ali, Mohammad Tahir Shah, Seema AnjumKhattak, Mohammad Farhan

Alluvial gold is abundant in the Quaternary deposits of the Kabul and Indus rivers in District Nowshera, Khyber Pakhtunkhwa, Pakistan. Understanding the provenance of alluvial gold using morphology and elemental composition could be helpful in developing an exploration strategy of regional benefit. Detailed morphological studies of gold grains revealed high flatness index values which are indicative of a distal source. Compositional studies of 58 gold grains using SEM and EMPA showed broadly similar Ag ranges (1– 15 wt%) for each sample and occasional Cu values in individual gold particles to 0.4 wt%.Whilst the Ag profile is not diagnostic, the Cu values are compatible with derivation from either porphyry systems or ultrabasic rocks. The complex geology of the drainage catchments could host gold mineralization of other styles, but larger sample suites would be required to refine the current interpretation to establish whether particles which are simple Au-Ag alloys could be derived fromorogenic or epithermal sources. This scoping study has demonstrated that the compositional and morphological studies of gold grains are useful in providing information regarding the nature and location of the source of placer gold in areas where there is limited information on the nature and location of in situ mineralization.

Oct 6, 2020

By E. Knell

COM Energy, Inc., a subsidiary of Occidental Petroleum Corporation, has constructed a 1.6 million hectoliter-per-year COM plant in Jacksonville, Florida. COM will be distributed to customers in the region as a substitute for fuel oil presently burned in boilers and kilns. As the market for COM grows, COM Energy, Inc. expects to build additional units both in this country and overseas. This paper addresses the overall status and technical aspects of the project, focusing on the facilities for COM production and utilization.

Jan 1, 1982

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article concludes a two-part series on the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. Discussed are the consequences of fuse abolishment, the technical feasibility of changing to an alternative system, and an economic analysis of initiation systems. Last month, part one (ME, pages 31-35) described current use of initiation systems, incidence of accidents, and consumption values for safety fuse and other initiation systems. Consequences of Fuse Abolishment Cap and Fuse Manufacturers Two major safety fuse manufacturers, Ensign Bickford and Apache Powder Co., share the US fuse market. Marketing of Ensign Bickford safety fuse is done by Dupont. Dupont manufactures electric caps as a main product and recently introduced a new nonelectric initiation system (Detaline). Therefore, Dupont would be only slightly affected by the elimination of safety fuse from metal and nonmetal mining. Ensign Bickford, though a larger manufacturer of fuse, does not appear to emphasize the safety fuse market. In fact, safety fuse sales represent only about 10% of Ensign Bickford's total sales volume. Ensign Bickford is strongly pushing its Nonel product. It appears, therefore, that the elimination of safety fuse would have a limited effect on Ensign Bickford, and could ultimately be to the company's advantage. Apache Powder Co., however, would be seriously affected if safety fuse was eliminated. Safety fuse, although not its only product, constitutes a major source of revenue for the company. It currently does not manufacture a substitute product. Apache Powder Co.'s manager agrees that prohibiting the use of safety fuse would result in a greater market share of initiators for Ensign Bickford. Hercules could also benefit from the prohibition of safety fuse. Metal and Nonmetal Mining Industry According to an explosive company contact, elimination of safety fuse by a mandatory regulation would force some of the small, marginal mines out of business. Another powder company representative believes that eliminating safety fuse will result in uneasy situations for small operators not familiar with other techniques. These operators try to minimize the costs and traditionally like safety fuse. He believes that insufficient proof exists to substantiate the overall safety increase if the fuse is eliminated. Fuse manufacturers and distributors disagree, then, about the impact of safety fuse elimination. However, they tend to agree on some important points: • Safety fuse can be a safe method if applied properly. • Electric blasting can be dangerous due to stray currents, and may have higher misfire rates than safety fuse. • It is very difficult to compare the rate of misfires and partial round failures for different systems. This is due simply to the nonavailability of such data. In many cases, the misfires are not even reported to the shift boss, as required by regulations. • Safety fuse has high acceptance in certain applications, such as a face where Nonel or detonating cord are used, or in open-pit blasting. • The safety fuse industry appears to be phasing out on its own. It is expected that the fate of the safety fuse market will be similar to that of black powder. An investigation by Nitro Noble of Sweden "clearly states that the diminishing use of safety fuse has considerably reduced the accidents in Swedish mines." Mine Data Acquisition and Analysis As a part of the study effort, visits were arranged to 24 metal and nonmetal mines. In most cases, underground visits were accomplished. At least one drilling and loading operation was witnessed. The mines were grouped into four mining areas: Wyoming, Montana, Idaho; western Colorado and eastern Utah; Missouri; and southern Arizona. Of all mines visted, the safety fuse system was used in 11 mines, electrical system in seven, Nonel in five, and the Hercudet system in one surface mine. At each mine, the manager, foreman, and blasting crew were interviewed for information and opinions. Besides informal discussions with mine officials, a questionnaire was also filled out for each mine. Due to the extensive length of the information gathered, these data are not presented here.

Jan 2, 1984

By M. D. Bishop

Early solvent extraction circuits in the uranium industry utilized bona fide kerosenes as diluents for extractant chemicals. These kerosenes were used successfully in the uranium industry; however, at least one plant was destroyed by fire resulting from the use of a low flash point kerosene. Although the term "kerosene" is used throughout the solvent extraction industry, the authors have been unable to find any use of kerosene in copper solvent extraction circuits. A term that is occasionally used with reference to diluents is "metallurgical kerosene." Such a term is unrecognizable in the petroleum industry. Kerosene [or kerosine] is a flammable hydrocarbon mixture that is less volatile than gasoline. It is produced for combustion purposes and may have variable compositions of organic compounds including alkanes, alkenes, alkines, and aromatics. Diluents are constant composition hydrocarbon mixtures developed specifically for use in solvent extraction processes. These products usually have much lower vapor pressures and higher flash points than kerosene. In solvent extraction systems, they typically comprise 70 to 95 v/o percent of the circuit organic. The primary purpose of the diluent is to adjust the extractant concentration to the working range of the operation. The diluent and extractant must be completely soluble or miscible with each other. Secondary diluent effects are to promote transfer kinetics, optimize phase disengagement, and minimize both organic in aqueous and aqueous in organic entrainment.

Jan 1, 1996

By Kanaan Hanna, Mir Heydari, Dipack Sengupta, Gordon B. French

This article, first in two, discusses the safety, technology, and economic impact of eliminating safety fuse from metal and nonmetal mines. It is based on operation and manufacturer experience over the past five to 10 years. If safety fuse is eliminated, blasting accidents will decrease. There should be only limited technical impact. The economic impact will be minor for large operations, but will be significant enough for small operations that some will likely close rather than change. Most mines would probably change over, with the market absorbing the extra cost. Elimination of safety fuse would obviously have an impact on the two safety fuse manufacturers. One manufacturer produces an alternative system and would be unaffected. The other, however, will be affected if it does not change its production strategy. From the standpoint of employment and production, abolishing safety fuse will have a very minor effect on the mining industry as a whole. This article discusses the current use of initiation systems, incidence of accidents, and fuse consumption. Next month, part two describes the economic impact of eliminating safety fuse on the mining industry and manufacturers, and presents an economic analysis of the initiation systems. Introduction The objective of this study was to determine the safety, technology, and economics of eliminating safety fuse from metal and non-metal mines. There were five major tasks: • Studying initiation-related accidents from the Health and Safety Accident Center (HSAC) data file; • Visiting mines, collecting relevant data, and interviewing mine operators; • Establishing the trend in safety fuse consumption and type of users; • Corresponding with fuse manufacturers, domestic and foreign; and • Developing an idealized blasting cycle to evaluate the possible economic impact of safety fuse elimination on large and small operations. More than 450 explosives-related accident reports have been screened and analyzed by investigating HSAC files. These reports have been studied and classified according to the four initiation systems, size and type of mines, and time and frequency of accidents from 1973 through 1978. Twenty-four mining operations were visited to obtain supporting data for this study. Mine personnel were interviewed to determine attitudes about safety fuse and alternative detonating systems. This article decribes available data. It also attempts to provide information that can be used to answer such questions as: • Is the use of safety fuse (an antiquated detonation system) a major cause of mining accidents? • Are alternative systems available that could result in fewer in-juries to miners?

Jan 1, 1984

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By R. M. Hays

Jan 1, 1980

By P. J. Cook

Comminution is one of the fundamentals of mineral processing, requiring large expenditures to be made on capital equipment, installation, power and maintenance. The trend toward lower grades and higher operating costs, mean mining operations are becoming increasingly marginal. The challenge is to improve and more importantly, utilize crushing and milling technologies that provide for reduced capital and operating costs whilst providing increased unit efficiencies. The Svedala Barmac Autogenous Crushing Mill presents such an opportunity by providing many of the cost savings and production increases required by its ability to produce a finer mill feed size and realize reduced energy consumption. This paper briefly describes the operation of the Svedala Barmac Autogenous Crushing Mill and reviews its benefits towards improving the efficiency of crushing and milling operations.

Jan 1, 1999

By S. A. Suhler

The detection of hazardous geological anomalies through remote sensing techniques is the subject of current research efforts sponsored by the U.S. Bureau of Mines. In this review, hazardous geological anomalies are discussed with respect to the "view" presented along with potential operational concepts for each technique. The design and development of a borehole radar is described with emphasis on the potential range and resolution capability of the system under realistic underground conditions. Results of field tests at two coal mines and at a hard rock future subway location are presented.

Jan 1, 1978

By D. M. Hausen

Carbonaceous gold ores are ubiquitous to virtually all of the Carlin-type gold deposits along the Carlin gold belt in north central Nevada, representing the unoxidized "zones" of presumably extinct thermal spring systems of mostly Tertiary age. A period of subtropical weathering resulted in deep sub-lateritic zones in most deposits to several hundred feet below surface. Carbonaceous ores below this supergene profile of weathering have been investigated by various methods, including petrographic study, standard geochemical and organic carbon analyses, carbon and hydrogen isotopic ratios, electron-spin resonance spectra, infrared spectra, and DTA techniques. Results have been integrated with recent findings by other investigators utilizing fluid inclusion and thermal brine data to indicate a first phase hydrothermal solution temperatures and pressures at a minimum depth of 6 km under normal geothermal gradient. This phase resulted in the quartz-barite-calcite vein filling of the host rocks. Gold mineralization took place later at shallower depths. Primary organic material in carbonaceous ores from the Carlin and other mines appears to be a pyrobitumen residue derived from an old oil pool that had been heated by the thermal solutions, and from which the light hydrocarbon fractions were removed. Some of the bitumen was remobilized along silicified veinlets in the ore, but its role in the emplacement of the gold, itself, is not clear. The gold was localized submicroscopically in fine pyrite, mostly in framboids, and as fine metallic particles, but does not appear to be concentrated within the carbonaceous matter per se. However, reducing conditions associated with bituminous residues are believed to have been favorable for gold deposition.

Jan 1, 2013

By Alper Kirmaci, Taghi Sherizadeh, Dogukan Guner, Samuel Nowak, Khaled Mohamed, Morgan Sears

Coal ribs present a major safety hazard in underground mines, and there is currently no unified approach for their design in the United States. To tackle this issue, this study investigated the stability of underground coal pillar ribs under development load. Utilizing over a thousand 3DEC models, a framework for calculating coal pillar rib rating (CPRR) was developed. A detailed step-by-step method was outlined for computing the CPRR based on a 3DEC analysis, which was then validated with various 3DEC models, demonstrating a strong correlation between the two models. The results demonstrated that the rib factor of safety (RibFOS) under development load is directly proportional to CPRR, coal mine roof rating (CMRR), and floor strength, and inversely proportional to the overburden depth and rib height. Moreover, a regression equation was formulated to predict the RibFOS based on the aforementioned parameters. Furthermore, empirical relationships were developed between the RibFOS and the applied primary rib support density (PRSD) in U.S. coal mines. To ease the calculations, a stand-alone application, Design of Rib Support (DORS), was developed. This application can be used to assess rib stability and easily calculate CPRR, RibFOS, and PRSD.

Jul 1, 2023

By S. S. Peng

The generation and transportation of the airborne dust are mainly governed by the velocity and the movement pattern of the ventilation air in the longwall face. Generally speaking, the higher the air velocity, the more the airborne dust will be generated and the longer the period of the dust of certain size will be carried away from the source. In order to effectively prevent the production and the spread of the airborne dust, The airborne dust concentration distribution in the longwall face must be known in advance. Before the dust concentration distribution can he predicted theoretically with confidence, the air velocity distribution pattern of the ventilation air in the longwall face area must be determined first. However, the complicated, time-dependent and unpredictable mining conditions along and around the face area make the theoretical studies of the problem rather difficult. For instance, one of the factors commonly affecting the air velocity distribution at the longwall face is the air leakage, either into or from the gob area. The leakage quantity and the location of occurrence differ from mine to mine, face to face, and time to time. They depend not only on the compactness of the caved roof fragments in the gob, but also on the degree of obstructions in the working space and in the return entry. Another obstacle to the theoretical studies about the velocity distrbution is the complicated boundary conditions of the ventilated spnce which is very difficult to represent accurately in mathematical forms. In this paper, the air velocity distributions measured in four longwall faces are presented. A statistical model for each longwall face is also derived for prediction of air velocity distribution in the longwall face.

Jan 1, 1985

By P. G. Semple

For the last four years, the Kilborn Group of Companies has been involved in several major projects in the Confederation of Independent States (CIS). These include the Kumtor project, the Kubaka gold project, the Kazgold project, the Aginskoe project and the Jerooy project. These projects are all in various stages of detailed engineering and construction. Western mining companies are pursuing mining opportunities throughout the world in search of ore bodies for development. The quest for profitable mining ventures has led mining companies to South America and Asia and, more recently, to the former Soviet Union. When considering the CIS, several factors should be considered. The most notable are geography, mining culture and previous mining production.

Jan 1, 1996

By O. P. Sinha, Biswajit Mishra, A. K. Mandal, Raj Kumar Dishwar, G. S. Mahobia, Ram ji Omar

Most of the mineral deposits found in North-East India remain unexploited due to inadequate knowledge on their status, economic viability, and requisite mining technologies. The aimof this study is to characterize the multimetallic magnetite mineral deposit from the Nagaland area in India. The quality of iron ore was evaluated to establish its suitability as a raw material for iron production. Detailed studies were conducted to establish the composition and properties of the samples. X-ray diffraction (XRD), X-ray fluorescence (XRF), electron probe micro-analyzer (EPMA), and petrographic microscopy techniques were employed in the investigation. Shatter and tumbler test was performed for analyzing the mechanical properties of the ore. XRD studies indicated that magnetite is the major mineral with low amounts of martite, maghemite, and quartz. XRF/EPMA results indicated that magnetite contains 35–65 wt.% of iron and 1–5 wt.% of chromium. It also confirms the presence of Ni and Al up to 1 wt.% and Si up to 6 wt.%. Chromite-rich ore contains up to 30 wt.% Cr and 15–20 wt.% of Fe.

May 10, 2021

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.