Search Documents

By Steve Kral

The Clinton administration’s policies toward the environment have the mining industry on the defensive. The president and US Secretary of the Interior Bruce Babbitt continue to bypass Congress in their efforts leave an environmental legacy when they leave office in a year. So the mining industry must take its case to the public. And the public seems willing to listen if the industry is willing to tell its story, according to US Rep. Chris Cannon (R-UT). Cannon was one of the keynote speakers at the105th meeting of the Northwest Mining Association, in Spokane, WA. The conference, held in early December, attracted about 2,400 people and more than 200 exhibitors

Jan 1, 2000

By W. A. Hoyer

Neutron activation analysis for mineral identification has attracted the attention of numerous investigators, judging from the publications on this subject in the past few years. 1-9 The appealing aspect of this method of mineral analysis is its proven sensitivity in the laboratory. In principle, activation analysis is one of the few petro-physical methods whereby a direct analysis for a mineral itself is possible in a borehole. The successful application of activation analysis requires the use of particular neutron reactions, measurement of selected gamma-ray energy intervals, and optimum bombardment and detection times. For copper analysis, Labanov et al., 10,11 using a low-energy PuBe source, reported an acceptable logging means. On the other hand, Pradzynski12, in analyzing ores and process tailings, used high-energy neutrons and photons for surface measurements of process samples. The work of Labanov et al. was based on measuring the rate of decay of the activated copper and hence was not as definitive as might be desired. Equipment is commercially available to carry out activation studies in the field 13,14 Gamma-ray spectra can be successfully transmitted over ordinary logging cables and, with borehole high-energy neutron accelerators and lower-energy chemical neutron sources, a variety of neutron activation methods can be studied. The purpose of the study discussed in this paper was to determine the feasibility and practicability of logging for copper using neutron activation techniques and commercially available equipment. The laboratory study showed that Cu could be detected in rock samples in the laboratory by high-energy neutron activation of 63 Cu. In the field, however, due in part to the large volume irradiated, the direct detection of copper using high-energy neutrons was not as promising. Detection of copper by measuring both the direct gamma-ray emission and the excessively strong low-energy gamma-ray absorption appears promising. Copper was not detected either in the laboratory or

Jan 1, 1972

By R. J. Sweigard

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. An investigation was conducted of current mined-land planning practices to aid in the development of a procedure for evaluating postmining land use potentials. This investigation considered both the industry and public planning approach to mined-land planning and was based primarily upon three case studies conducted in various regions of the United States. The site planning process that was developed during the investigation is iterative in nature and has been designed specifically for the mining industry. It centers around preliminary studies and data collection, development of land use alternatives, and the evaluation of alternatives. Use of this process facilitates the evaluation of economic, environ- mental, and social impacts of postmining land use alternatives. In this paper, the process is presented along with a description of its development, application, and significance.

Jan 1, 1984

By A. Metzer

When paraffinic gases (ethane, propane, butane) are used as the gas phase in flotation systems, the initial rate of flotation and recovery are generally increased as compared with air. The mechanism of the effect of paraffinic gases in flotation was studied and it was shown that they co-adsorb with the collector ions on the mineral-aqueous solution interface. The effect of this co-adsorption was interpreted in terms of apparent increase of the effective chain length of the collector by the co-adsorbed gas. Adsorption densities, contact angles and flotation behaviour were studied on the following systems: a) Quartz - dodecyl ammonium chloride - ethane and propane b) Calcite - sodium oleate - propane and butane. The positive effect of the co-adsorbed gases is a maximum at low collector concentrations or where critical conditions for flotation with air prevail.

Jan 1, 1974

At the 25th Peruvian Mining Convention, the start-up of Antamina was called ?the mining event of the year.? Antamina, one of the largestcopper-zinc mines in the world, began operations in May 2001.Augusto Baertl is Executive Chairman of Compañía Minera Antamina, the operating company. He said in a convention address that Antamina would be in full production in 2002. ?I would like to stress that Antamina is, in every respect, a highly stringent operation, as it intends to be the Peruvianmine of the future,? Baertl said. ?Antamina has set the target of being, and remaining throughout time, a model mine as to technology, environmental practices and social responsibility.? [ ] In the areas of technology and operations, Baertl noted that ?we have incorporated the best engineering design available and state-of-the art technology for mining, grinding and transportation processes, among others.? In the environmental area, he said that ?we have carried out careful environ-mental impact studies and have incorporated modern technologies and methods to control and minimize any environmental impact.? In the social field, Baertl noted that ?our relationship with neighboring communities is being developed under the premises of the social responsibility philosophy.? These include popular consultation processes, environmental committees and conciliation discussion committees. The purpose, he said, is to encourage communities located within the area of influence of the project to find and lead by themselves their path toward sustainable development, beyond the life of the operation itself.?

Jan 1, 2001

By Michael P. Connor, O&apos

The Wing Hill Garnet Deposit, located near Rangeley, Maine, forsed through assimilation of Early Paleozoic metasediments by an intrusive Devonian gabbro. The resulting ore body is exceptionally large and high-grade, consisting of 50-70% almandine garnet. Following open-pit quarrying, the ore is trucked to Industrial Garnet Extractives' mill in West Paris for final processing. Two grades of abrasive are produced - a pure, premium grade INDUSTRIAL GARNET and the Lower grade co-product IGE UTILITY GRIT, both of which are available in a variety of sizes. INDUSTRIAL GARNET is marketed world- wide into a diverse marketplace including both loose grain and bonded applications.

Jan 1, 1985

By Bo Hyun Kim, Mark K. Larson

Fault-slip bursts induced by mining activities can result in severe damage to nearby mine development. In general, engineers designing rock support in burst-prone mines not only need to consider stress redistribution resulting from excavation, but also dynamic loading that results from seismic waves generated by large mininginduced fault-slip events. In this study, we simulated dynamic waves in sedimentary rock from a blasting source and from a mining-induced-seismicity source using a Universal Distinct Element Code (UDEC) model with discrete fracture networks (DFNs). Our purpose was to investigate the stability of openings and the adequacy of existing support systems at an underground limestone mine in South Korea. A baseline model with only static loading was also simulated, which verified observed stability under such conditions. The results indicate that the current support system of shotcrete lining is likely to work well under dynamic loading caused by blasting. However, when the dynamic source was a far-field fault-slip event, the dynamic loading exceeded the support capacity of the shotcrete lining. Thus, if a mine is operating in ground with an elevated risk of mininginduced fault slip, mine engineers should consider seismic wave propagation and ground motion distribution from a remote, mining-induced fault-slip event to determine a suitable support design.

Jul 1, 2023

By Roland W. Rammler

In recent years, the crude oil reserves of the world have increased at the same rate as the consumption. A Consideration of the global figures suggests that adequate supplies of petroleum will be available during the next decades. On the other hand, it in a fast of economic and political significance that the reserves in the industrialized countries increase much more slowly than in the developing countries. In Western Europe the reserves have even decreased. At the present time, about 70 % of the petroleum reserves of the world are in the Middle East and in Africa in regions in which political arises are prevalent or impending. For the industrialized countries, the discrepancies between the consumption and reserves in various regions of the world are a strong urge to investigate whether oil can be recovered from other sources. The situation will probably not be changed to a large extent by the discovery of oil in the north of Alaska. The main starting materials for the production of synthetic crude oil are coal, oil shale and tar sand. In North America, where the consumption of petroleum increases more rapidly than the reserves, there are enormous deposits of each of the three materials. This fact is another incentive toward the utilization of these unconventional oil reserves, which provide a reliable basis for a supple of energy for a long time to come.

Jan 1, 1970

By D. C. McLean

One of the few innovations in hydrometallurgy in recent years has been the utilization of the chemistry of basic iron sulfates called jarosites. These have been used to make iron-zinc separations in the processing of zinc concentrates and are a very important factor in both the Duval and Cymet copper chloride processes as a means of preventing iron build-up in the closed leaching circuits. Copper oxychlorides are kindred compounds in that they are insoluble basic salts that form at low pH (1.5 to 3) and precipitate selectively from many base metal solutions. They have been reported in the chemical literature as far back as 1860, and a few of them are known in their mineralogical forms (particularly atacamite) usually as nuisance minerals because of their chloride content. Several patents describe their synthesis and use as fungicides and insecticides, and papers have discussed their formation as corrosion pro¬ducts on copper and brass piping (14).

Jan 1, 1979

By F. G. Miller

To improve coal flotation Bethlehem Steel Corporation's Research Department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies5 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the bas is for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14M x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level.

Jan 1, 1968

By Alfred Opengart

During any rush hour, tens of thousands of automobiles clog the main highways leading into or out of our large cities. Inevitably one or more cars stall or plow into another, causing a momentous traffic jam. Traffic backs up for miles as drivers try to maneuver around the roadblock. As commuters, we grin and bear the inconvenience, rationalizing the delay as part of the price one pays to live in a modern society. The truth of the matter is that the engineers planning the roads have the know-how to build adequate bypass alternatives into their design. The problem is one of economics -- can the cost of eliminating roadblocks be justified? Engineers designing solutions to complex materials handling problems for modem distribution centers are just now beginning to ask this question in relation to their work. Unfortunately in many instances, it has taken an expensive "traffic jam" to bring this question to the front. In these cases, a seemingly practical system promising an attractive return on investment -- using the latest equipment and computer controls -- was designed and installed. Everything went according to plan until one day a breakdown occurred. .Product flow stopped, and management realized it was at the mercy of the "machine." In such situations, management had assumed it could minimize the risks of the breakdown by injecting extra manpower to operate the system manually and pay the associated costs. What it had not recognized is that manual intervention is nearly impossible with sophisticated systems. Thus, too often -- and sometimes too late -- management found itself footing a very high bill for losses incurred because of major production stoppages and missed customer shipments.

Jan 1, 1973

By Lawrence K. Nordell

The selection of belt conveyor drive systems (*) is the subject of ongoing investigation. Frequently this choice has been governed by an incomplete perspective on the major considerations. A more comprehensive and objective approach is desirable. This paper presents additional factors which hopefully will broaden this perspective. BACKGROUND Conventional belt conveyors are powered by electric or electro-mechanical drives(*) mounted at the conveyor's head, tail, intermediate return span, or a combination of these (Fig. 1). A list of the drives reviewed is given in Table I. The following are main elements influencing the selection of the drive system: 1) dynamic characteristics, 2) economic factors such as capital cost, plant spares compatibility, reliability, availability, maintainability, and 3) environmental constraints. The principal dynamic characteristics of concern are the reactions of belt forces generated by the drive system during starting of the conveyor. Another attribute for consideration is the application of multiple driven pulleys used to 1) lower the conveyor's belt tension requirements, 2) increase the expected tonnage throughput, allowing for possible drive component failures, and 3) increase the plant spares flexibility related to the drive assembly.

Jan 1, 1977

By Mark A. Koestel

Cobalt-sulfide mineralization can he found in potentially economic quantities where permeable, basal Cambrian formations "pinchout" against Precambrian pal eotopographi c highs. These environments are common around the Saint Francois Mountains of southeastern Missouri and they share many similarities with the geologic environments of Zambia and Zaire in South Africa. Exploration for this type of deposit involves test drilling targets identified by trend analysis from past drilling, geophysics, geochemistry and a comprehensisve study of regional geology and isopach maps. Innovative ideas, new exploration concepts and insoluble residue geochemical methods may provide the necessary "edge" needed to complement basic geologic understanding leading to ore discovery.

Jan 1, 1987

Machine breakdowns and maintenance delays are large contributors to lost production and increased operating costs in the mining industry. The U.S. Bureau of Mines is investigating the applications of expert system technology to diagnostic and predictive maintenance tor mining equipment. This will help increase mining productivity and decrease operating costs, by reducing the frequency of equipment failures and repair times. The Bureau has begun this effort by applying expert system techniques to the diagnosis of hydraulic system problems on a continuous mining machine. This paper discusses the development of the hydraulic diagnostic expert system.

Jan 1, 1990

By T. Emery, D. Sweet, J. Bourgeois, B. Seymour, D. Porter

Cemented rockfill (CRF) is being used to backfill primary and secondary stopes at the Eagle Mine, an underground nickel and copper mine operated by Lundin Mining. National Institute for Occupational Safety and Health (NIOSH) researchers from the Spokane Mining Research Division (SMRD) are conducting cooperative research with the mine staff to determine if the size of a CRF sample affects its measured strength properties. Based on previous research by NIOSH, cylindrical samples of CRF ranging in size from six to eighteen inches in diameter were cast at the mine and cured underground. The samples were later transported to the SMRD laboratory and the Michigan Technological University where tests were conducted to determine the strength and elastic properties of the CRF. To further analyze the relationship between backfill density and compressive strength, different ASTM International compaction techniques were used to cast the samples. For comparison, tests were also conducted on in-situ core samples that were drilled from a stope which had been backfilled with the same CRF mix. The data collected from this study not only improves our understanding of CRF in-situ properties but also helps optimize Quality Assurance/Quality Control (QA/QC) methods for backfill preparation and testing.

Feb 1, 2023

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world's major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

By Musa D. Manzi, Raymond J. Durrheim, Richard T. Masethe

An investigation into the source mechanism of mining-induced seismic activity plays a vital role in understanding the various modes of failure observed in the underground deep-level South African mining environment. The seismic events data for this study was captured by the mine-wide seismic system operating at Kloof Gold Mine. This system comprises 40 4.5 Hz tri-axial geophones sampling at 6 kHz installed at locations that surround the stopes mining the Ventersdorp Contact Reef (VCR), Main Reef (MR) and Kloof Reef (KR). A set of 103,753 mining-related seismic events (-3.0≤ ML ≤2.7) that occurred during 2017 and 2018 was selected for this study. The mining depth of these seismic events ranges from 1600 – 4200 m; most located close to stopes mining the VCR ore body. The main criteria used to select a subset of events for detailed analysis were the number of stations that recorded the seismic event and the azimuthal distribution of the sensors.

Apr 26, 2022

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023

Laboratory tests were conducted to evaluate the silica collection efficiency of flooded-bed scrubbers with six different filter panel designs and at two operating velocities. Test results indicated that reductions in filter density negatively impacted respirable dust collection. Silica collection efficiency for the least dense filter was as much as 33 % lower than the collection efficiency of the densest filter. At the low operating velocity, the least dense filter allowed over 40% of the respirable silica dust in the scrubber intake air to pass through the unit, where it would be discharged back into the mine environment. Operation of the scrubber at the higher test air velocity increased silica collection efficiency, regardless of the filter panel tested. The density of the filter panels also impacted the quantity of air that is moved through the scrubber, with higher density filters reducing scrubber airflow. For each filter, the relationship between dust collection efficiency and air moving capacity must be considered to determine overall effectiveness for specific mine applications.

Jan 1, 1998

By W. V. Bluck

Higher coal quality is being recognized in potentially lowering the cost of power as measured at the bus bar. Assessment of potential coal supplies for most any given power plant is now going beyond buying at the lowest delivered fuel cost and is now taking into consideration other factors such as handling, storage, pulverization cost, boiler fouling, post combustion cleanup, and waste disposal costs. New measurements of quality are being considered now by those producing and those consuming the fuel by assessing numerous variables in the total fuel cycle to achieve the lowest possible power costs.

Jan 1, 1983