Search Documents

By Jed Greenwood, Lyall Workman, Michael Haggerty, Russell Sheets

Draglines often work from a position on the active highwall or spoil side bench to remove undisturbed waste material and spoil in the previously mined pit. To protect the dragline crew members and the machine, it is necessary that the highwall remain stable while the dragline is present on the bench. In the past several years, we have been involved in determining the causes for highwall failures that included the dragline. While there have been no injuries and limited dragline damage with these incidents, the potential certainly exists for a more serious outcome. In all cases, the operation had completed a geotechnical study to support the ground control plan and pit designs. However, all these incidents included aspects that would not likely have been identified in studies to determine highwall and spoil designs to support ground control procedures. In general, these events included aspects that were localized and would have been difficult to identify in initial slope stability studies either observationally or during the soil testing and modelling efforts. Although the authors do not have quantitative evidence of this, it does seem there has been an increased number of events in recent years. This may be due to loss of institutional knowledge, mining in more challenging areas, or simply an increase in localized variation. This paper will describe some of the issues we have seen and what the causes of failure were. It becomes clear that avoiding similar incidents in the future requires on-going observation and inspection of active highwalls and spoil benches to try and identify local variability and impact on mining. The information can proactively be used to update stability modeling of any concerning issues to determine likelihood of problems and to develop solutions.

Feb 1, 2025

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By P. A. C. De Ruiter

The Lower Cretaceous salt deposits of the Gabon Basin and Congo Basin were said down on ton of an Burly Cretaceous Lato Jurassic, continental graben fill that represent!) the rifting phase of the Afro-American continent. The salt 13 characterized by high percentages of potash and magnesium salts and the scarcity of sulphates and carbonates. The salt probably originated from a brine that was already enriched in high-soluble salts before entering the Gabon Congo basins. Their low-solubility equivalents are found in the Cuanza Basin of Angola. Commercial mining of the potash salt is only possible in those onshore areas where it is essentially undisturbed, shallow and of the right chemical composition. These conditions are net in Congo where the Holle mine produces from rich sylvinite deposits.

Jan 1, 1978

By A. Haghighat

The Missouri University of Science and Technology?s (Missouri S&T) Experimental Mine is a teaching and research facility which has been excavated in limestone by mining engineering students over almost 100 years. The mine is currently being extended to a second level. Available fans for ventilation are two surface fans of 24 kW and two underground booster fans of 12 kW. The design of a ventilation network in conjunction with multi surface fans and booster fans entails a complex procedure. Ventsim Visual software modeling has been used for network analysis to determine the optimum surface and booster fans locations, blade settings, and speeds. Both natural and mechanical induced ventilation pressures have been taken into account. Three working faces on each level have been designated as target points that minimum air quantities are required. The model has been calibrated against a pressure and quantity survey. Design of ductwork, door/stopping positions and different fans characteristics have been examined. The optimum flow rate at identified working faces, efficiency and minimum energy losses and annual network power cost determine the best scenario. The optimum design has been determined for the ventilation network for the next 100 years. The optimum flow rate across working faces is the key criterion selected.

Feb 23, 2014

By Dale K. Nash

The authors have developed a com¬puter-assisted critical path planning and scheduling model to help reduce time required to move longwall mining units. The model includes time constraints and limited resource constraints, such as manpower, machinery, supplies, work space, and transportation routes. Outstanding results were achieved on the first move to which the computer-model pas applied; e.g., downtime due to the move was cut by 50%. The model and the schedules developed using it provide an excellent blueprint for future moves and have led to significant savings in time and costs for Emery Mining Corporation, Huntington, Utah.

Jan 1, 1983

By M. Kuchta

A linear integer programming (MIP) model to solve the long-and short-term production-scheduling problem for sublevel caving operations is presented. The MIP model is designed as a multi-time-period problem to provide monthly schedules that meet production, blending and sequencing requirements. One of the most important issues during the development of the MIP model was the requirement of sequencing between blocks. In this mathematical model, unique constraints that ensure sequencing of the production from sublevels are developed. A suggested method of handling a large number of variables is also given. The MIP scheduling model was implemented on a data set obtained from the Kiruna Iron Ore Mine located in northern Sweden. The initial MIP model implementation was successful and provided a solution that optimized resource recovery while meeting monthly and yearly production constraints. The scheduling results obtained based on the Kiruna Mine are further presented and discussed.

Jan 1, 2003

By Felicia F. Peng

An economic analysis for evaluating coal preparation plants in the Appalachian Region is presented. A complete coal preparation plant which includes multi-streams and/or multi-stages coal cleaning circuits, complete closed water circuits, environmentally acceptable refuse disposal and reclamation systems is used to determine the capital and operating costs. The plant is capable of producing metallurgical grade clean coal or deep cleaned steam grade coal for future power generating plants use. Utilizing a profit maximization as a decision criterion, an optimal yield, and optimal coal clean¬ing circuits, closed water circuits, and disposal and reclamation systems for a given coal characteristic may be selected among the process alternatives by using a process simulation-economic model of the coal preparation plant. A deterministic analysis is used to calculate the discounted-cash-flow interest rate of return (DCFIROR) and project the selling prices, and determine the Return on Investment (ROI) for the cases of 32.65% and 52.74% plant utilization with producing two cleaned products. Sensitivity analyses are performed to quantify the effect of total capital investment, operating cost, run-of-mine cost and yield on an economic criterion-ROI and selling prices. A probabilistic evaluation using the Monte Carlo simulation technique is further made to quantify the risk involved in obtaining the desired profit levels. The results of the economic analysis for a given coal preparation plant configuration and characteristics of raw coal indicates that the selling prices of producing two cleaned products are greatly affected by the change in percent of plant utilization (production schedule), yield, and run-of-mine cost, and total capital cost. The sensitivity analysis also shows that the total capital investments has a three times greater effect on required selling prices than operating costs. The risk analysis shown that the overall economics look very attractive with current coal sale prices and 52.74% plant utilization.

Jan 1, 1979

By Steven E. Paulson

In situ mining is emerging as a potential alternative to conventional surf ace and underground mining techniques. A major factor in determining recoveries by in situ mining is the proportion of ore minerals that can be contacted and solubilized by the leach solutions. To provide basic information on the processes occurring during in situ leaching, particularly at the microscopic scale, the Bureau of Mines has developed a geologic characterization research program. This includes laboratory experiments using leaching apparatus that can accommodate whole core samples. Whole core experiments result in higher leach solution-ore mineral contact ratios than packed column experiments, and also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels in the rock. A nonreactive, reusable reaction cell has been designed and tested. The leaching apparatus can be used for constant-pressure or constant-flow experiments and allows for the control of flow rate, pressure, and temperature during the experiments, thus permitting studies on a wide variety of ore samples. Details of the experimental apparatus and design are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grande, AZ, area.

Jan 1, 1987

By William A. Riggs

Salt, a non-metallic mineral whose use dates back to earliest history of mankind, and whose uses cover the widest range for any mineral raw material, is generally of widespread occurrence in commercially recoverable quantities in the oceans, in certain sedimentary rocks, in certain lakes, and in certain underground waters. Passing over geological detail, it may be said that, generally, all of the salt in the world has, at least once in geological history, been in solution in the oceans. The total salt content of today's oceans, said to equal 4.5 million cubic miles of rock salt, dwarfs the tremendous volume of salt in the sedimentary rocks. In 1958, United States production of salt was about 22 million net tons and world production about 82 million. About 3 percent of United States production is table salt, with chemical, municipal, industrial and agricultural uses taking the remainder. Mississippi River. Figure 1 has been expanded sufficiently to show also those salt occurrences and producing points which might economically ship salt into these states. Although widespread in occurrence, salt deposits and possible production areas generally show very sharp local boundaries. Salt-for non-table use is susceptible to ?place value?, a common problem in low valued raw materials, where transportation costs often exceed the value of the material f.o.b. the production point. Generally only large capacity mechanized salt producing operations can compete in United States markets, as contrasted to the many small local salt evaporators in less industrialized Mexico.

Jan 1, 1962

By S. Managi, M. C. Williams, N. H. Behling

Particle processing is a key to using solid particles in fuel cell applications. Selectivity with regard to reactivity, impurities, etc. is important feature and the treatment of particle surfaces could greatly impact the performance of direct carbon fuel cells. Solid fuel particles will become increasingly important in the future. Present energy conversion systems for solid fuels are too inefficient. New energy conversion systems for solid fuels with higher energy conversion efficiencies are possible. Fuel cell technology is a key-technology in these new conversion systems. The direct carbon fuel cell (DCFC) operates on carbon particles obtained from a variety of solid fuel feedstocks. The DCFC is the only fuel cell designed to directly oxidize carbon particles in a special anode chamber. The particles are generally graphite structure with high purity. The electrolyte used is the high temperature solid oxide, molten carbonate or hydroxide electrolyte. Since a pure stream of CO2 is produced the stream can easily be sequestered and disposed. Pure carbon dioxide produced as a by-product would also have a market in many industries. A well-defined technology roadmap identifying key research and development (R&D) issues is necessary to provide a framework for the development of these systems and to prevent entrenchment in inherently inefficient technologies. This review paper describes the direct carbon fuel cell and its system, how it works, the developmental status, the characteristics of the carbon particles needed, and the research and development issues for the technology. INTRODUCTION The DCFC has been under development for many years. It was researched as early as 18961), but an intense research and development is necessary to realize its potential. William W Jacques, a US electrical engineer and chemist, described a DCFC in 1896 in US Patent 555511 for a “Method of converting potential energy of carbon into electrical energy”. Jacques used coke electrodes in a molten NaOH electrolyte. Molten carbonate fuel cell (MCFC), solid oxide (SOFC) or hydroxide electrolyte (AFC) technologies can be used as the basis for the DCFC technology. A schematic of the direct carbon fuel cell in the MCFC mode is shown in Figure 1. The molten carbonate fuel cell operates at approximately 650°C (1200°F). The high operating temperature is needed to achievesufficient conductivity of the carbonate electrolyte, yet allow the use of low-cost metal cell components. A benefit associated with this high temperature is that noble metal catalysts are not required for the cell electrochemical oxidation and reduction processes. For the hydrogen reaction the half-cell electrochemical reactions are

Jan 1, 2019

By Ramon B. Santos

The Atlas Concentrator, reputedly the largest in the Far East today, is located on the island of Cebu in the Republic of the Philippines. It started operation on a 4000 TPD capacity in 1955. An expansion program, coupled with significant improvements both in the Crushing Plant and the Mil, made the Atlas Concentrator what it is today, treating about 14,000 tons of ore per day at a comparatively low cost of about $0.50 per ton treated. The Atlas Copper Mine is at present mainly an open pit operation, with ore supplied from two pits (Lutopan and Biga) north of the Concen¬trator. Development of an Underground Mine, situated on the main ore body at Lutopan, which will be a block caving operation, has been underway since 1963, and this underground mining operation is expected to b e in full production by the latter part of 1966.

Jan 1, 1966

By Richard S. Klein

Frozen coal creates severe handling problems. Utilities require uninterrupted supplies of coal to meet their increasing coal consumption rates. Difficulties incurred due to frozen coal result in more costly downtime for the utilities. Air cannons, vibratory hammers and thaw sheds are examples of mechanical devices used to break, crack or thaw frozen coal. Recently chemical treatments have been developed as preventive measures. The freezing of coal depends upon a number of factors, of which one of the most significant is surface moisture. The more there is, the larger the frozen coal problem. Slide 1 depicts a graph of frozen coal compressive strength as a function of surface moisture. Below a certain minimum value the coal will not freeze. Above this point, compressive strength is essentially a linear function of moisture over the range practically encountered. By surface moisture is meant the free moisture on coal having a normal vapor pressure as opposed to capillary moisture or inherent moisture. In addition to the straightforward freezing of coal surface moisture binding particulates together, frost formation occurs due to temperature gradients which develop in rail-cars and stockpiles .

Jan 1, 1980

By E. Molleman

This paper reports on testwork exploring the dissolution/reprecipitation reaction: ZnS + 2HCl ? ZnCl2 + H2S, as part of a process for the production of pure ZnS. In spheroidal form, this would constitute a premium fonn of zinc refinery roaster feed enabling the production of pure ZnO. The research focused on the influence of proton activity on dissolution of zinc concentrates from Brunswick Mining & Smelting, Red Dog and Tara. The results and thermodynamic data suggest that the three concentrates contained significant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1997

By Eugene F. Eisemann

This paper is concerned principally with the competition between fuels for industrial use in the United States. Total energy consumption in the U. S. is allocated between industrial and other uses The industrial volume is divided into two classifications (1) where-there is competition between fuels and (2) where there is no competition. The pattern of fuel consumption by electric utilities was studied because there, is competition between fuels and because it is the fastest-growing industrial market. Electric utilities fuel consumption is discussed by geographic area. The growth of each fuel in several areas is investigated. The analysis of these areas, includes the study of the relationship between prices where fuels are in, competition:- (1) on the East Coast where price competition occurs between oil and coal, and (2) in the southeastern states where competition exists between coal and gas..

Jan 1, 1961

By L. Yan, D. Yantek

Federal regulations require refuge alternatives in underground coal mines to sustain life for 96 h while maintaining an apparent temperature below 35 °C (95 °F). Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat and humidity buildup is a major concern with refuge alternatives because they have limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding a refuge alternative is complex and not easily defined, analytically or experimentally. To investigate heat and humidity buildup in refuge alternatives, NIOSH conducted multiple in-mine, 96-h tests on a 10-person tent-type refuge alternative, a 23-person tent-type refuge alternative and a six-person metal-type refuge alternative. The results show that when moisture was introduced to represent perspiration and respiration from miners (wet tests), the average temperature at midheight increased by 10.5 °C (18.9 °F) and the RH approached 88 percent for the 10-person tent-type refuge alternative; the average temperature at midheight increased by 9.4 °C (16.9 °F) and the RH approached 94 percent for the 23-person tent-type refuge alternative; and the average temperature at midheight increased by 7.7 °C (13.9 °F) and the RH approached 95 percent for the sixperson metal-type refuge alternative. For the dry tests, where no moisture was introduced, the average internal temperature increased by 12.6 °C (22.7 °F) for the 10-person tent-type refuge alternative, by 10.3 °C (18.5 °F) for the 23-person tent-type refuge alternative and by 8.4 °C (15.1 °F) for the six-person metal-type refuge alternative. These results may provide refuge alternative manufacturers and mine operators with guidelines and considerations for evaluating temperature profiles for portable refuge alternatives. The information may then be used to make decisions on occupancy ratings and heat mitigation strategies based on the thermal environment in which the refuge alternatives will be installed.

Jan 10, 2018

By G. Ofori-Sarpong, A. -S. Adam, R. K. Amankwah

"In the application of the BIOX® technology, high tailings grade (2-16 g/t) may be generated with a decrease in overall gold recovery, which sometimes make it economically unattractive. This paper investigated the causes of the high tailings grade by using samples from the Bogoso BIOX plant. Partial chemical analysis, diagnostic tests and cyanidation optimisation studies were conducted to invoke understanding into the high tailings grades. Diagnostic study on the tailings showed 48.34% of gold in carbonaceous matter, 17.12% in quartz, 13.40% as liberated gold, 11.51% imbedded in sulphides and the remaining 9.65% in carbonates. Optimum cyanidation recovery of 90.4% was established for the BIOX concentrate at 7 kg/t NaCN, 40-50 g/L activated carbon and residence time of 40 hours. The recovery was sensitive to carbon and cyanide concentrations but additional cyanide was not economical. High preg-robbing indices of 72.7% and 64.4% were recorded for the BIOX product and the flotation concentrate respectively. This confirms the inability of the BIOX process to deactivate carbonaceous matter, which remains a serious precursor for low overall gold recoveries and high CIL tailings. INTRODUCTION Gold ores may be broadly classified as refractory and non-refractory. Non-refractory ores are easy to treat but refractory materials require complicated flowsheets for metal extraction (Hausen and Bucknam, 1985; Schmitz et al, 2001; Marsden and House, 2006). As near surface non-refractory gold deposits are getting depleted, the increasing price of gold and increasing demand for gold, have encouraged many gold producing companies to treat refractory ores for gold recovery. The refractory behaviour of these ores may be due to the presence of sulphides, tellurides, cyanicides and/or carbonaceous matter. Refractory ores do not respond well to conventional cyanidation as the gold is either occluded by or in solid solution in sulphides, or is in association with cyanicides (Marsden and House, 2006). Further, carbonaceous matter preg-robs gold during leaching (Osseo-Asare et al, 1984; Hausen and Bucknam, 1985; Schmitz et al, 2001). The two major causes of refractoriness are the presence of sulphides and carbonaceous matter, and these render the ore double refractory (Nyavor and Egiebor, 1992). Oxidative pre-treatment processes such as high pressure leaching/oxidation; biological oxidation, ultra-fine grinding and roasting are required to render refractory ores amenable to conventional cyanidation (Marsden and House, 2006). Biological oxidation, however, has become the preferred pre-treatment route because it is more environmentally friendly and convenient even where only partial oxidation is required. Comparative tests have demonstrated that bioleaching can achieve the same or better results than roasting or pressure leaching in terms of gold recovery (Yannopoulos, 1991; Brierley, 1997). Further, biological treatment processes are more cost-effective, environmentally friendly and safer."

Jan 1, 2017

By W. R. Reed, S. Klima, J. Driscoll, T. W. Beck

"Tests were conducted to determine properties of four foam agents for their potential use in longwall mining dust control. Foam has been tried in underground mining in the past for dust control and is currently being reconsidered for use in underground coal longwall operations in order to help those operations comply with the Mine Safety and Health Administration’s lower coal mine respirable dust standard of 1.5 mg/m3. Foams were generated using two different methods. One method used compressed air and water pressure to generate foam, while the other method used low-pressure air generated by a blower and water pressure using a foam generator developed by the U.S. National Institute for Occupational Safety and Health. Foam property tests, consisting of a foam expansion ratio test and a water drainage test, were conducted to classify foams. Compressed-air-generated foams tended to have low expansion ratios, from 10 to 19, with high water drainage. Blower-air-generated foams had higher foam expansion ratios, from 30 to 60, with lower water drainage. Foams produced within these ranges of expansion ratios are stable and potentially suitable for dust control. The test results eliminated two foam agents for future testing because they had poor expansion ratios. The remaining two foam agents seem to have properties adequate for dust control. These material property tests can be used to classify foams for their potential use in longwall mining dust control. IntroductionAbout one-half of U.S. underground coal is produced by longwall mining, which allows for mining high volumes of coal but generates significant amounts of coal mine dust. This can lead to overexposures for longwall miners and possibly occupational respiratory diseases, including black lung and silicosis, which have no cure and can be disabling or fatal. The only method to avoid these occupational illnesses is through elimination of exposure to respirable coal mine dust and crystalline silica (quartz). The current occupational exposure limit for respirable coal mine dust is 1.5 mg/m3 during each shift that a miner is exposed in the active workings of the mine or in mine facilities (Mine Safety and Health Administration (MSHA), 2015a). When respirable quartz is present, the mine must maintain average concentrations at or below 0.1 mg/m3. If the mine exceeds the 0.1 mg/m3 respirable quartz dust concentration, then the applicable respirable dust standard is reduced, calculated as 10 divided by the percent quartz present (MSHA, 2015b)."

Jan 1, 2018

By L. Alagha, L. A. Sanchez-Calderon

The existing methods for recycling lithium-ion batteries present initial hurdles related to the safe handling and preparation of the batteries to avert potential explosions. Submerging batteries in sodium chloride (NaCl) solution has become an acceptable industrial practice. However, the use of NaCl to discharge lithium-ion batteries rusts the batteries’ cases and releases metals which impacts the downstream processes that involve selective recovery of Li. This study aimed to determine the optimal concentrations and pH range of NaCl for the discharge of lithium-ion batteries for the purpose of minimizing the leach of Al, Co, Cu, Fe, Li, and Ni.

Feb 1, 2024

By Colin Lawrence

The Port of New York and New Jersey is one of the most heavily used transportation arteries in the world, handling nearly 40 per-cent of the North Atlantic shipping trade and directly providing nearly 230,000 jobs to the local economy. In 2004, $100 billion worth of consumer goods moved through the port. To accommodate future cargo volumes in the port, which are expected to double over the next decade and possibly quadruple in 40 years, deeper shipping channels are needed to provide access for a new generation of cargo mega-ships with drafts exceeding 13.7-m (45-ft) when loaded. Current channels within the harbor range in depths up to 13.7-m (45-ft), thus preventing carriers from using these larger ships, or requiring significant reductions in cargo to achieve lesser drafts to operate safely within the harbor. As part of the Harbor Deepening Project, the Anchor-age Channel would be deepened to 15.2 m (50 ft) below mean low water (MLW), for a length of 5,790 m (19,000 ft). The New York City Department of Environmental Protection (NYCDEP) owns, operates and maintains two existing water siphons in the harbor. Due to their shallow depth, both existing siphons must be relocated before dredging of the Anchorage Channel can be completed. Tom Costanzo, manager of capital programs for the Port Authority of New York and New Jersey (PANYNJ), says that ?While the re-location of the existing siphons under the Anchorage Channel is vital to the success of the deepening program, it is also a story of cooperation among key agencies at different levels of government resulting in improvements that will benefit the people of this region greatly.?

Jun 1, 2010

By A. E. Sears

The intent of geomorphic landform design is to mimic the function of the natural landscape. In a surface mine reclamation application, geomorphic landform design has the potential to mitigate stream loss. This research quantified features of reference landforms and performed computer modeling of a conceptual valley-fill design using geomorphic landform principles. A design was created using published design parameters with a software design tool (Carlson Natural Regrade with GeoFluv). Three additional designs, incorporating field-obtained regional geomorphic landform parameters, were completed and resulted in a geomorphic landform design specific to southern West Virginia. This work illustrates the importance of field determination of the ridge to head-of-channel input and drainage density parameters. Values of ridge to head-of-channel distance measured in this study were consistently an order of magnitude greater than software recommended values (SRV); SRV = 24 m (80 ft) versus field= 220 m (720 ft). Similarly, for the drainage density parameter, the software recommended range is 6 to 9 km-1 (80-120 ft/ac). The field measurements for central Appalachia quantified the drainage density to range from 5 to 5.3 km-1 (67-70 ft/ac). This affects Appalachian valley-fill stream construction by making the stream lengths shorter and the land slopes steeper with straighter headwater channels compared with areas in the southwestern United States. While the application of geomorphic landform design to surface mine sites presents challenges, this work provides support for future applications.