Search Documents

By Sam Ash

The Murray Mine was one of the first mechanized cut-and-fill underground gold operations in northern Nevada. At the end of 2002, mine production began to decline. So the mine entered a phase of remnant mining and began preparations to close down. The remaining mining took place along the ore waste boundary in previously condemned areas and in challenging ground conditions. To remain economically viable, new techniques were implemented in operations, geology, engineering and rock mechanics. These improvements pushed the edge of known and accepted mining practices and have allowed the Murray Mine to remain in operation.

Jan 1, 2006

By Beth Robinson

This first of two articles on the Second Mexican Mining Rail Excursion describes some of the more casual experiences participants enjoyed on last fall’s rail tour of major Mexican mining operations. In this article, Beth Robinson, a graduate student at Colorado School of Mines, describes trip organizers, participants, and some of the unique events occurring during the two-week excursion. Next month, part two of the series will highlight various Mexican mines and plants.

Jan 1, 1982

By A. Cole, F. Porretta

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

Jan 1, 2002

By J. M. Hollow, D. E. Walsh, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Carbon fines are collected by a filter press because of their gold value. Samples of the carbon fines show that they consist of 20-30% carbon, 70-80% grit and 0.17-0.68 kg/t (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in a form of recrystallized free gold grains, with the balance being adsorbed gold on the carbon. High recoveries of gold and carbon were obtained in laboratory tests using froth flotation, with a high rejection of the grit.

Jan 1, 2001

By U. Richter

Conveyors are a highly effective means of transporting material over long distances. Recently there has been a trend toward long conveyor systems with high capacity single flights. These conveyor systems are an efficient alternative to costly truck fleets. Also with deeper mines, the use of diesel driven trucks becomes more difficult. Another trend is in underground mining, where conveyors are an efficient alternative to drift hoists or dedicated rail systems.

Jan 1, 2012

By P. Anyon

Exposure to the microscopic particles in diesel engine exhaust can lead to serious health problems, including the incidence of cancers, heart disease and increased susceptibility to respiratory ailments such as pneumonia, bronchitis, and asthma. In Australia, mining companies and state government authorities are actively responding to this major occupational health and safety issue. Their initiatives place considerable emphasis on routine monitoring of diesel particle matter (DPM) exhaust emissions, both for engine benchmarking and as a part of routine engine maintenance. Implementation strategies follow two complementary paths: determination of individual engines? emission signatures combined with periodic engine re-certification; and co-operatively agreed industry-government engine maintenance programs, which are subject to audit. Both strategies place heavy reliance on real-time measurement of DPM concentrations in engine exhaust, using ruggedized instrumentation, mainly based on laser light scattering photometry. Adding value to this cooperative approach, industry has also collectively funded a government agency to design and manage a database, into which the results of all-routine DPM testing can be uploaded directly by individual mines. This win-win outcome is a great example of how cooperative action between governments and industry can deliver the goods: in this case, a safer working environment, more efficient energy use and the capacity to benchmark performance with industry peers.

Jan 1, 2009

By J. MacFadyen

The U.S. cement industry, including Puerto Rico, again set a record in terms of production and shipments. The increase in shipments came primarily from imports of portland cement as domestic production from produced and imported clinker gained only 1.9 Mt (2.1 million st). Clinker production as reported to the U.S. Geological Survey (USGS) was 88.6 Mt (97.6 million st), an increase of 1 percent. Gray and white portland cement production from domestic and imported clinker, estimated at 93.5 Mt (103 million st), was up 1.9 Mt (2.1 million st). Masonry cement shipments of 5.5 Mt (6 million st), which equates closely to production, was up 6.3 percent. Blended ce-ment shipments were up 35.9 percent from 2004 at 2.35 Mt (2.6 million st).

Jan 1, 2006

By Felicity Lloyd, Stuart Kearns, Roger McLimans

The metamorphic terrane of southwestern India is a geological environment containing ilmenite source-rocks, transport drainage systems, and resultant beach sand deposits that contain altered ilmenites greater than 60wt% TiO2. As such, this environment provides a geological laboratory, from source to deposit, for the investigation of ilmenite origin, alteration, and geochemical character. Ilmenite samples from potential source rocks, river sands, and beach sands all show degrees of alteration and a variety of alteration textures (iron leaching) producing leucoxene (here defined as >70 <90wt% TiO2) and progressing to rutile (here defined as >90wt% TiO2). Distinct alteration textures are specific to different source rocks and are used together with trace element geochemistry as provenance criteria. Ilmenites are classified on the basis of their trace element content. In India, the ilmenites are classified principally according to the Mg, Nb, and Mn content and this signature defines potential source rocks, even where the ilmenite is altered to a TiO2 content of 70wt%. The trace element data may fingerprint source rocks whose ilmenite is more prone to iron leaching and that criterion has application in exploration for higher-grade ilmenites.

Jan 1, 2005

By K. Zabrusky

Estimation of high grade epithermal vein deposits can present challenges in correctly representing the continuity of grade within an undulating structure. One solution to this problem is to use dynamic anisotropy to follow local variations in the strike and dip of veins. Dynamic anisotropy (D.A.) allows the search parameters to change block by block throughout the model to account for the local variations. Presented here is a study of a vein that changes orientation down-dip. A traditional resource estimate using one search ellipse orientation was performed. The resulting estimated grades did not accurately reflect those of the sample data. Using a search ellipse with an average value for the two distinct dips caused the grade estimation to be less representative than desired. Rather than performing domain-based analysis with different search ellipses, the issue was corrected by using Datamine Studio 3?s D.A. function. The 3D vein trend was used to estimate the dip and dip direction of the vein in each block. The resulting D.A.-estimated model follows the two dip trends of the vein. This software makes a previously tedious task faster, and allows for more accurate estimations.

Feb 27, 2013

By Edward Hall Smith

The E1 Indio Mine is located in the Andes mountains about 180 kilometers East of La Serena, capital of the Fourth Region of Chile. It is reached by an international highway running up the Elqui Valley as far as Juntas from where the last 42 kilometers is on a road constructed by the Company. The plant is located at 3.900 meters above sea level among extremely rugged terrain with nearby mountains rising about 5.500 meters. Climatic conditions at these altitudes are severe with winter temperatures down to -20°C. Snow storms lasting several days and leaving up to two meters of snow have been experienced, while fierce winds are corm=.

Jan 1, 1984

By Leonel Lopez

Throughout Mexican history, mining has been an important, traditional activity. Before the "Discovery of America," native miners worked a variety of deposits throughout the country, including Mixtec gold and gem mines in Oaxaca State and Aztec gold, silver and copper from mines in Michoacán. The 500th anniversary of Mining in Mexico after the "Discovery of America" was initiated by the Mexican mining sector on April 15, 1991. As early as 1548, when the Guanajuato mining district was discovered, Mexico had become a leading world producer of precious metals. Since then, Mexican mineral production has developed in cycles, responding to changing technological, economic and political conditions. During the 20th century, Mexican mine output reached its peak in the decades of the 1930s and 1940s, when it was producing about 40% of the world&apos;s silver, 15% of its lead, 10% of its zinc, 4% of its copper and 3.5% of its gold. In 1990, by way of contrast, these percentages of world output stood at 13.5% for silver, 4.7% for lead, 4.1% for zinc, 3.2% for copper, and 0.43% for gold. The lowest production levels were recorded during the 1960s and 1970s, when Mexicanization of the industry and increasing state controls weakened mineral economics to a point that mineral exploration budgets were sharply reduced or eliminated, along with the industry&apos;s future. Only the noble old mining districts continued to supply production, with occasional eruptions of "bonanzas" and new extensions in established mining districts.

Jan 1, 1994

By William H. Hansmire

The Modified Detroit River Outfall No. 2 (MOD DRO-2) will discharge treated wastewater to the Detroit River. Construction of a 6.4-m-diameter, 1.9-km-long tunnel was halted in 2003 by flooding during tunneling with an open face hard rock TBM. A new design for a higher rock tunnel, a ?Modified? design, was completed in 2007 and Notice to Proceed to the tunnel contractor was given in November 2008. Project duration is four years for completion of tunneling and start of outfall tunnel operation. This tunneling project has high groundwater pressure (5 bar), pervious limestone rock of up to 140 MPa (20,000 psi) strength, and hydrogen sulphide in the groundwater. The new tunnel will be connecting to access shafts and outfall diffuser riser shafts previously built for the now-abandoned tunnel. The new tunnel design construction contract, and initial planning to use a pressurized-face (slurry) hard rock TBM are presented.

By D. L. Stevens

Following an in-depth scenario and strategic planning exercise in 1997, Noranda’s mine production goal was set at 500,000tonnes per year of both copper and zinc metal within five years. There had been no recent discoveries, reserves were shrinking and things had to be done differently and quickly. Change is now continual in our program but here is what we did first: - Combined the exploration and business development groups - Formed teams to search for and respond to opportunity - Made our geologists more business minded and our engineers more optimistic - Went global - Set clear thresholds, farmed out the marginal properties, fast tracked the others - Focussed reconnaissance exploration where we had a clear competitive advantage - Became a “flexible” partner to both juniors and seniors

Jan 1, 1999

By H. Fayed

Two-phase (water and air) flow in a self aerated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). A 0.8 m3 model is considered. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Because of the lack of circumferential periodicity in this machine, the entire machine is modeled and unsteady simulations are conducted in the whole volume of the bulb. Uniform bubble diameter is specified, and the effects of bubble diameter are determined by conducting simulations for three diameters of 0.5, 0.7, and 1.0 mm. The unsteady air flow rate through the machine is predicted as an outcome of the simulations. Air volume fraction contours and velocity field in different parts of the machine are presented and discussed.

Jan 1, 2012

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow inby the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

Jan 1, 2007

Seven legendary figures of American mining will be enshrined in the National Mining Hall of Fame in ceremonies on Saturday, Sept. 7 at the Little America Hotel in Salt Lake City, UT. The 15th annual induction banquet will begin with a reception at 6 pm, followed at 7 pm by the dinner and the program. Of the seven inductees, one is living. He is Alexander Murray (Bud) Wilson, 80, of Los Altos, CA. Wilson led Utah Construction (later Utah International) to become one of the world’s most diversified and successful mining companies in the 1960s and 1970s. It was acquired by General Electric in 1976.

Jan 1, 2002

By S. Assemi

Interaction forces between a hydrophilic silica particle and an air bubble were measured by atomic force microscopy using simplified model systems with deionized water and dilute KCl solutions. Contributions from the hydrodynamic force were minimized by using a low piezo speed. Particle-bubble separation distance and the bubble spring constant were calculated from linear regression of the piezo extension versus cantilever deflection. The bubble surface potential was then estimated from fitting the AFM-measured forces to the Hogg-Healy-Fuerstenau (HHF) model, using the surface element integration (SEI) method. Surface potentials obtained for the bubble at a low applied force were comparable with the literature data, suggesting that the simplified model used here can give a reasonable estimation of the bubble surface potential under moderate applied forces. Interaction forces between a silica particle and an air bubble were also measured at different locations on the air bubble surface. The force curves obtained at the edges of the bubble fitted very well to the theoretical force curves regardless of the applied force, while curves obtained at the center and halfway to the center, were more difficult to fit, in particular at higher applied forces (> 13 nN), suggesting that force curves obtained at the edges of the air bubble might be less prone to deformation effects.

Jan 1, 2008

By David Kwietnewski

Roadheaders are gaining widespread acceptance in North America as a means for mechanical tunnel excavation. Until recently, almost all of the large-scale North American tunnel projects were excavated one of two ways ? the tried and true drill-and-blast method or with the use of tunnel boring machines (TBM), the hi-tech super-excavators. TBMs enjoyed fast-growing popularity worldwide as TBM manufacturers offered greater technology to meet the demand of the civil tunnel industry in the late 20th century. Recently, though, more tunnel projects, large and small, can thank the brute force of a roadheader for getting the job done.

Jan 1, 2011

By R. H. Mullennex

Application of depositional analysis concepts is becoming an ever-increasingly more important and more useable tool in exploration and development of coals in the Appalachian basin. Over the past decade, a rather large number of studies, papers, and publications have addressed various aspects of depositional environments of coals and, to some extent, applications to development. As would be expected as regards a subject so complex as Pennsylvanian sedimentation in the Appalachian basin, certain academic studies have produced conclusions at variance in some aspects to those of other studies. Overall, however, there has been a building- block progression and general refinement with time of understanding of the depositional settings and other factors controlling Appalachian coal distribution, quality, and other minability parameters. Most attempts to explain coal seam characteristics have revolved around a basic deltaic model. Some have attributed certain seam attributes to upper delta plain deposition, other attributes to transitional-lower delta plain settings, and yet others to lower delta plain environments, and so on. While these approaches have provided valuable insight into some general coal characteristics, they are somewhat incomplete and are, in a sense, too broad for specific mine-scale applications. Further, it is apparent that in order for widespread peat accumulation to occur, there must be a drastic decrease in the energy of the depositional system and amount of sediment being brought in, compared to the active deltaic and coastal processes responsible for deposition of the large volume of clastic sediments that dominate the Pennsylvanian system of the Appalachians. Consideration of this fact implies that peats (coals) may not necessarily reflect depositional settings that are directly coincident with those associated with adjacent rocks. Cecil and Englund (1985) address this point, and quite correctly state that "the primary controls on major stages of peat formation are allocyclic processes involving paleoclimate, eustatic changes in sea level, and tectonics." While this statement is inarguable, it does not negate the importance and usefulness of depositional analysis in predicting reserve characteristics that may impact mining and marketability.

Jan 1, 1986

By A. J. Stewart, M. Guay, J. W. Critchfield, A. P. Hoddeson

The MetroWest Water Supply Tunnel project includes three main work shafts, excavated primarily in rock. Shaft L is 9.8 m (32 ft) diameter and 124.1 m (407 ft)deep. Shaft E is 7.0 by 12.8 m (23 by 42 ft) and 91.4 m (300 ft) deep. Shaft 5A is 7.9m (26 ft) diameter and 72.5 m (238 ft) deep. Construction methods are compared and contrasted. Lessons learned involve a differing site condition in soil overburden, contractor-proposed modifications, and remedial slurry wall work. Other aspects discussed include noise and vibration control, groundwater inflow, water treatment, muck handling and contract administration issues.

Jan 1, 1999