Search Documents

By R. Owen, T. Canty, C. Marks

The industrial vision system provides on-line 2D particle size analysis for aggregate slurries in both the overflow and underflow of hydrocyclones. This paper covers required vision system features allowing CCD cameras to function in the harsh environment of a mine milling area. The study conducted demonstrates the system’s capacity to obtain particle size distributions for controlling hydrocyclonic separators. The particle size distribution is obtained within seconds and immediately updated to allow for process adjustments. Results are then provided as a graphical computer generated display or output as a 4-20mA current loop for process control. The primary use of the vision system is in classifying particles in cyclone overflows which are often a few microns in size. Typical size information for actual mine slurry samples are presented and possible control schemes discussed.

Jan 1, 2002

By Edwin R. (Original by) Phelps

Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining; 4) Surface mining normally recovers a- much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining [ ] methods because of geologic reasons such as the nature of the roof or bottom, thickness of the seam, multiple bedding, etc.

Jan 1, 1981

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

Several common ratios used for determining spontaneous combustion activity rely on comparing the amount of various products of oxidation with the amount of oxygen consumed to produce these products. As coal gets hotter, oxidation reactions become more efficient meaning more products produced for less oxygen consumed. There are many problems associated with accurately determining the true amount of oxygen used. These problems relate to the monitoring technique (and its associated uncertainties) used to generate the results, deficiencies in the established equations utilized in calculations, dilution with other gases and other sources of oxygen depletion. Typically the oxygen deficiency is over estimated, resulting in the under estimation of the indicating ratio. For this reason the use of ?one off? calculations to determine the status of the underground environment is not recommended. Instead trends of these ratios should be used to identify increases which indicate an increase in oxidation intensity. This paper outlines problems associated with the monitoring techniques and equations used to determine the oxygen deficiency.

Jan 1, 2009

By S. Holtermann

Through the process of Riverbank Filtration (RBF), the Louisville Water Company plans to obtain a higher quality source of water for their B.E. Payne Water Treatment Plant (WTP) by means of four collector wells located in the alluvial aquifer along the bank of the Ohio River. The collector wells are connected to a 2,850 L/s (65 mgd) pumping station by a 2,362 m (7,750 ft) long, 3 m (10 ft) finished diameter tunnel located in limestone and shale bedrock, which is approximately 45 m (150 ft) below the surface. High tunnel boring machine (TBM) production rates were achieved in this moderately weak bedrock; most of the tunnel only required support in the crown. An unanticipated water-bearing fault and unanticipated ground behavior proved challenging and required quick thinking to minimize impacts to construction. Tunneling conditions are discussed in detail, together with the methods used for overcoming the groundwater and ground behavior challenges. The tunnel is expected to be completed in April 2009.

By Richard Gertsch, Jack Eloranta, Leslie Gertsch

An ongoing research program is characterizing the ore qualities that most affect mine and mill processing of iron. Current practice uses assays of magnetic iron and silica, but additional qualities are needed for advanced process control. If additional qualities can be measured from core, blastholes, or process samples, they can be modeled and controlled similarly. What qualities, other than assays, hinder or facilitate beneficiation at each processing step, and how can they be measured in the mine/mill ore stream? This paper describes preliminary determinations of the effects of ore chemistry, hardness, blasthole drill performance, fragmentation control, and grindability on mill performance.

Jan 1, 2005

By Gregory D. Savage, Bruce M. Everett

Introduction The growing role of Colombia as a major supplier of internationally traded steam coal has been widely discussed in the industry. Although Colombian coal has been produced and exported in small quantities for a number of years, the country's position as a major coal exporter began in earnest in 1985 with the first commercial exports from the Cerrejon North Block Project. The mine is located on the Guajira peninsula in northeast Colombia, about 145 km (90 miles) from the coast (Fig. 1). In addition to the mine itself, the project involves construction of a dedicated railroad and port. This forms a modern, efficient, and integrated system. The project is embodied in a 50-50 association contract between International Colombia Resources (Intercor), a wholly-owned subsidiary of Exxon, and Carbocol, the Colombian state coal company. Intercor and Carbocol share investment and operating expenses equally. Intercor has the additional responsibility of managing operations on behalf of the partners. Each partner is entitled to 50% of the coal produced, and each markets its share separately. The project is a multi-seam, truck and shovel operation, based on large reserves (2 to 3 Gt or 2.2 to 3.3 billion st) of high quality bituminous coal. Exports began in the first quarter of 1985, at modest levels through what is called Early Coal Facilities. The permanent coal handling system began operation in February 1986. Production will increase rapidly in each of the next few years, reaching the design capacity of 15 Mt/a (16.5 million stpy) in 1989. Based on available resources, however, the resource will support expansion, and continued growth in production into the 1990s is feasible. Importance of transportation The success of a new coal export venture, such as Cerrejon, depends heavily on efficient transportation. In the international coal industry, overland and ocean transport can in some cases account for 40% to 50% of the final value of the product. Many coals, such as western US subbituminous coals, cannot reach export markets at all because of their low heat content and great distance from export markets. By the same token, low-grade resources are often commercially attractive for local markets even in the face of competition with much higher quality coals from distant sources. Figure 2 shows the growth in steam coal imports into Europe, the largest trading market. Through

Jan 6, 1986

By J. Humphrey

Introduction The weight of a Mining Truck can be affected by field modifications, the selection of items like tires, rims or even the conditions in which it operates. Truck performance and the compliance with a number of ISO standards, e.g. braking, steering and ROPS are dependent on truck weight. It is critical that truck owners understand the impact of changes in weight1. What makes this even more difficult for owners to evaluate is that there is no standard terminology or definitions for Mining Truck weights. This paper discusses and defines weight terminology, how it applies to performance and standards and the impact on the application of Mining Trucks.

Jan 1, 2007

By David G. Adam

Introduction Syncrude Canada Ltd. is the operating company for a consortium of industry and government participants that produce synthetic crude oil from their leases in the Athabasca Oil Sands. Production from the $2.3 billion (1978) integrated mining, extraction, and bitumen upgrading and utility complex started in September 1978. Production is currently about 6.4 Mm3/a (40 million bbl per year) of high quality synthetic crude oil. This is done by upgrading the extracted bitumen from the oil sands mined. Plans are to increase the production to 8 Mm3/a (50 million bbl pier year) by 1989. At that time, the mining operation will be required to deliver 100 Mt/a (110 million stpy) of oil sand (ore) to the extraction plants, and handle quantities of waste ranging from 50 to 75 Mt/a (55 to 83 million stpy). The Syncrude plant is located at Mildred Lake, 40 km (25 miles) north of Fort McMurray and 480 km (300 miles) north of Edmonton, Alberta. Climate, particularly winter, is therefore a major factor affecting the design and operation of all the Syncrude production facilities. Bitumen production, consisting of overburden removal, oil/sand mining, bitumen extraction, and tailings disposal, account for about half the total SCO production costs. Considerable research and development, therefore, continues to be applied to improve both material handling and bitumen recovery methods. Potential applications for feeder breakers were identified in the material handling aspects of both overburden and oil sand mining to reduce cost and to attain planned production increments. Overburden removal Overburden materials on the leases comprise thin Pleistocene sands, gravel and fill, and sands, silts and clays of the thicker Clearwater Formation with the silt to clay components predominating. The latter contains multiple leases of hard siltstone with unconfined compressive strengths up to 148 MPa and thicknesses up 0.1 to 0.9 m (1 to 3ft). Characteristics of the overburden as well as the climatic environment and scale of operation present unique problems for the efficient removal of the material. In a bucketwheel/conveyor system, the weak silty clay formations require relatively flat working slopes for safe operation, while the siltstone lenses and frozen overburden require blasting or selective removal by other equipment. These factors, combined with the normal bucketwheel/conveyor design parameters, lead to high capital investment and relatively inefficient use of that capital. Hydraulic mining alternatives, including dredging, are constrained by severe clay settling problems in the waste disposal

Jan 6, 1986

By R. B. Krog

The use of belt air as an intake source at longwall operations has greatly changed over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage, and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2009

Analysing a flotation plant?s operating performance requires accurate metallurgical sampling. Typically, the aims of performing flotation plant surveys are to establish a consistent and accurate understanding of the operation of the circuit as well as to identify potential areas for improvement. Once the data have been collected, a mass balance is required to provide a consistent set of data from which plant performance can be assessed. Mass balancing is a key skill that many metallurgists and mining industry professionals are familiar with. Mass balancing reconciles the feed and product streams throughout the plant and is sometimes used for accounting of the material entering and leaving a system (eg. JKMetAccount). However more common reasons for mass balancing are: better understanding of the flowrates within a system, assessing the quality of data obtained from sampling and surveys, and providing a key dataset for assessing and improving the performance of unit operations. Mass balancing requires practice and experience to determine if the results are reasonable. There are various software programs available to assist in the mass balancing and understanding of processing plants. This paper is focused on JKMultiBal initially developed by Gay (1993), and then later commercialized by JKTech. JKMultiBal in its current release is for balancing data in both one and two dimensions, i.e. balancing data on either sized or assay bases as well as size-by-assay. With the recent trend in flotation circuits becoming more complex, JKMultiBal has been used to gain a better understanding of the processes occurring within the circuit. This paper provides a description of the program as well as several case studies where the two-dimensional mass balancing has resulted in improvements in plant performance.

Jan 1, 2009

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By O?Connor. D. F.

The ever increasing energy costs associated with mining at depth has become an important issue that needs to be addressed for future sustainable production. Vale Inco Limited?s Creighton Mine being the deepest has the highest energy cost per ton due to the ventilation system requirements. A review of the ventilation systems was undertaken with respect to current practices and identification of opportunities to the practical application of technology that would facilitate energy savings. Energy conservation initiatives such as time of day controls have been implemented; however there still remained some opportunity for further reduction. Based on previous studies that identified opportunities due to actual time spent in the workplace, our mining method and ventilation design, it was determined that Ventilation on Demand (VOD) could provide further additional energy reductions with respect to our auxiliary fans. A pilot project has recently been initiated to apply a Ventilation on Demand concept to two 112 kW auxiliary fans and their related workings located on the 2340m level of Creighton Mine. The project objective is to determine the practical methodology and application of this technology in the field. This project involves the installation of variable frequency drive (VFD) starters on the auxiliary fans to allow variable volume (through speed control) based on demand. The required flow is determined based on equipment and/or personnel via identification tags. The Fans adjust to the flow requirements as measured by flow sensors. Since the fans are sized for the final requirements the required flows can be achieved regardless of system length. Energy savings are realized by supplying only the volumes (power) as required and only when required. This paper discusses the rational and program being tested at the VALE Inco Limited, Creighton Mine.

Jan 1, 2009

By L. M. Anisdahl

Ventiflex is a flexible ventilation duct system with a global market within mine and tunnel ventilation. The system is distributed in a wide range of qualities and dimensions. It is very important that ventilation systems are designed correctly in mines and tunnels. An incorrectly dimensioned system might result in bad air quality and too high costs. The objective of this study has been to assess some important design parameters for ventiflex comprising the friction loss factor for the duct wall itself, as well as the shock loss factors and the leakage factors for the different couplings systems. This has been obtained by carrying out a large scale experimental program on ducts with all the three different couplings: Velcro, zip and steel-ring. Pressure profiles and air flow rates have been measured, and based on these data the different factors have been calculated. The following results have been obtained: A friction factor l = 0,012 (K = 10) for the duct wall, a shock loss factor z = 0,0125 for velcro- and zip couplings, a shock loss factor z = 0,005 for steel-ring couplings, and a leakage factor f* = 0 mm2/m2 for all three coupling types. The latter result proves that no leakage is possible for a correctly installed duct with proper alignment. The results also confirm that ventiflex complies with class S, or better, according to the SIA-norm. However, whether ventiflex should be designed as class S, A or B according to the SIA-norm, depends on the particular application.

Jan 1, 2009

By D. S. Saxena, Jack K. Tuttle

Lack of understanding of useful applications of explosives on construction work stem primarily from the fact that explosion is commonly associated with destruction. On rock excavation and other construction works a certain quantity of explosive is harnessed to perform useful work at the source e.g. blasts to disintegrate rock. Development in rock blasting techniques, including the use of multiple-row blasting with short delay ignition, have made it impossible to excavate rocks close to or below buildings even in closely built-up areas. To permit the use of explosives on construction projects, in ways that will not damage existing structures, guidelines have been developed from careful measurements of intensity of ground vibrations. Accurate electronic instruments are now available for doing this. PLANNING AND CONTROL Blasting operations must be carefully planned and carried out to avoid discomfort to persons or damage to property. This increase in the use of rock blasting in city areas alone has led to a number of problems due to ground vibrations, air shock waves, and the psychological effect of noise. While the latter seldom if ever causes damage, it does create irritation and discomfort to persons living or working near the blasting sites. A result of this is a steady increase in the number of complaints in respect of damage to houses and other premises. Many such complaints are genuine and damage may undoubtedly be caused when incorrect blasting techniques are used.

Jan 1, 1997

By R. L. Loofbourow

R. L. LOOFBOUROW 26.1-WATER FLOW, USE, EFFECTS, CONTROL Sec. 4 discusses ground water as a mineral resource. This section deals wits its control. 26.1.1-IMPORTANCE Flows of water have an important effect on the cost and progress of many deep excavations. The existence of water limits the methods which can be used in some and presents hazards in others. Lowering the water table may reduce the flow of springs and wells, with legal liability. Some mine water is used directly, some must he treated before discharge, and some contains dissolved solids which can be recovered profitably. Loss of life, property and production from flooding is grim, yet scores of mines have worked safely for generations under ground-water reservoirs, lakes and even the sea. The need for better control of mine water is measured by the severity of recent floodings, concern with the quality of the effluent, and direct and indirect costs of working wet ground. There are improvements in freezing in shaft sinking. pumps and their controls, treatment of mine water before it is pumped, bulkhead construction and certain efforts to reduce inflow. 26.1.2-PUMPING COST VS. COST OF WET WORK Direct operating and capital costs of pumping are more evident than indirect items, such as provision of extra standby power and maintenance facilities, The total of all these items is the cost of pumping water from an excavation. This is only a part of the extra cost of working wet as compared to dry ground. Less productive methods, less efficient equipment and more expensive explosives may have to he used in wet work. Wet rock plugs certain equipment. Maintenance is higher and labor less efficient. The cost of any means of keeping work drier should he weighed against the higher cost of working wet. The true difference in the cost of working wet ground, compared with dry, probably is known at only a few places (see checklist of cost items. Sec. 26.4.13). An extreme comparison of mining wet and dry ore is available from Ambrosia Lake, N.M. (Fig. 26-1). Between 1963 and 1967, a wet and a dry mine were worked by the same company under conditions otherwise comparable. Average operating cost at the wet mine, pumping 1,600 to 1,800 gpm. was $16.06 per ton of ore. The comparable figure for the dry mine was $7.50. Principal differences included the fact that the wet mine was worked from drainage levels below the, ore with rail haulage, the dry mine in the ore with off-track equipment loading and hauling to the shaft. In the wet mine, ore packed in chutes, cars and skips and froze in surface bins, stockpiles and trucks. Wet-mine costs included drilling drain holes, building and maintaining ditches and pumping water containing abrasive solids.

Jan 1, 1973

By F. M. Doyle

Ion flotation shows great promise for recovering and removing metal ions from dilute process streams, either for environmental compliance or to recover values. This technique uses an ionic collector to concentrate non-surface active colligend ions of the opposite charge from a bulk solution at the solution?vapor interface. With a sufficiently large solution?vapor interfacial area (provided, for example, by sparging gas through the solution), the colligend can be concentrated and removed along with the collector in a foam phase. A key limitation on using the technique in the minerals industry, where many process streams contain a variety of ions and have relatively high ionic strengths, is the need to control which ions are interacting with the collector. Here the effect of three different chelating agents, namely dodecyldiethylenetriamine (Ddien), ethylene diamine tetraacetic acid (EDTA) and triethylenetetraamine (Trien), on the selectivity of copper, nickel and cobalt, or copper and alkaline earth metal ions, is reported. The results are discussed in terms of their implications for adoption in the minerals industry.

Jan 1, 2009

By Liming Yuan, John C. Edwards, Gene F. Friel, Robert A. Franks

Diesel fuel fire experiments were conducted in NIOSH’s Pittsburgh Research Laboratory’s (PRL) Safety Research Coal Mine (SRCM) to determine the critical air velocity for preventing smoke rollback. Such information is necessary for the preplanning and implementation of ventilation changes during mine fire fighting and rescue operations. The fire intensity varied from 50 kW to 300 kW depending upon the fuel tray area. Airflow in the 2 m high and 2.9 m wide coal mine entry was regulated during the course of each experiment; measured upwind from the fire as an average over the entry cross-section with an ultrasonic airflow sensor; and recorded dynamically with a mine monitoring system. The extent of smoke reversal was monitored with light obscuration monitors, ionization smoke sensors, and visual observations. Experimental results for the critical air velocity for smoke reversal as a function of fire intensity compared very well with model predictions based upon a computational fluid dynamics (CFD) fire dynamics simulator.

Jan 1, 2005

By Clay Haynes

While the Kansas River Tunnel is a relatively short, small diameter tunnel, the shaft excavation methods implemented were long and large on innovation and use of reverse circulation drilling equipment. ATS Drilling, L.P. used mechanical excavation techniques for both soil and rock segments of the 42.7 m (140 feet) and 38.1 m (125 feet) deep shafts that were 2.9 m (9.5 feet) and 4.1m (13.5 feet) diameter, respectively.