Search Documents

By Pengfei Pan, Lianjun Guo, Houguang Sun, Donglin Xu, Chi Yang, Lihua Luan, Daning Zhang

"Based on the introduction of production technology of Anqian mining company, the stope ore mass distribution was analyzed in detail. The processability indexes of different grade ores were obtained with magnetic tube whereas the grinding time, concentrate grade and concentrate yield were measured. On the basis of digital ore deposit model which integrates ore natural attributes and processing attributes, two stages of ore blending optimization models were established. The first stage model sought the minimum of stope ore transportation cost under the restraints of output ore grade and stope production. The second stage was a system optional model that aimed at the furthest use of resources meeting not only the production constraints of mining field and process field but also ore beneficiability and the system output requirements of the concentrate grade. Lastly, the solving method of big M simplex algorithm was discussed and used in production. 1. Foreword China is the biggest iron ore consumption market. But most of iron ore deposits in china possess such features as low grade, complex compositions, weak magneticity and refractoriness. Under the current economic and technical conditions, rational utilization of low-grade and refractory iron ore is strongly needed to improve the utilization ratio of mineral resources and keep mine development sustainable (Lei 2011). In recent years, the domestic research institutions and mines made a lot of achievements of rational development and utilization of low grade iron ore resources in the beneficiation technology and equipment, high and low grade balance, cost and tax analysis (Wang and Zhao 2013, Zhang 2014, Zhu and Li 2014), laying the foundation for reasonable utilization of low grade iron ore. In this paper, Anqian mining company is taken as an example in which the production conditions, raw ore quality control, different grade of ore processability, and ore blending optimization mode in mining pit and processing plant were discussed to achieve the maximum utilization of low-grade refractory ores under the economical and reasonable conditions. This will ensure the stable operation of mining joint ventures and maximize the enterprise's production life and therefore, maximize the economic and social benefits in the enterprise life cycle."

Jan 1, 2017

By K. Biswas, H. C. Lee, S. J. Jung

Ore passes are circular openings excavated in rock for in-mine gravity-transportation of ore. It is a very important component of the overall load-haul system of an underground mine. The function of an ore pass is two-fold: first, gravity-transportation of ore from the extraction level to the haulage level and second, the loading operation at the haulage level utilizing the gate assembly. In reality, like any other system component, an ore pass breaks down either due to a hang-up within the ore pass or due to a failure in the gate structure. The failure of the gate assembly may be attributed to a greater extent to the impact load as experienced by the components of a gate structure as a result of the direct impacts of the rock fragments and to a lesser extent to the static or 'dead weight' loads of the accumulated materials in the ore pass. This paper uses simulations in Working Model® as an aid to investigate the effect of both the impact and static loading on the gate assembly and on the inner-walls of the ore pass. The paper also investigates the impact of ore pass inclination and the presence or absence of dogleg on the static and impact loading of the same.

Jan 1, 2002

By P. C. van Aswegen

The Bacterial Oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery developed by Genmin, the mining division of Gencor, has been operating successfully at the Fairview mine since October 1986. The continuous operation of a pilot plant at Genmin Process Research has resulted in further process developments to improve plant operating efficiencies. These new developments which include a higher solids content of the pulp feed to BIOX®, lower retention times, higher operating temperatures, lower power utilization for oxygen dispersion .and reduced nutrient addition have all been successfully implemented on the Fairview plant.lt has furthermore been confirmed that the arsenic precipitate formed in the neutralization of effluent solutions complies to the United States of America EPA standards. Continuous cyanidation pilot plant work conducted on BIOX® product has indicated that cyanide consumption can be drastically decreased if a continuous flowsheet is implemented in preference to a batch leaching system.

Jan 1, 1991

By Charles H. Jacoby

In 1960 the management of International Salt Company made the decision that all waste material from the Watkins Glen plant would be stored in underground salt cavities. The cavities which they contemplated using had been depleted of salt to a point where continued operation would have impaired their structural stability. Originally, the waste to be disposed of included vacuum pan bleeds, cinders, contaminated salt and sewage. It was proposed that this material, in a slurry form, was to be injected into the salt cavity through one of the abandoned wells. Brine, displaced from the cavity, was to be recovered from an adjacent well and subsequently injected into the Cherry Valley limestone, This Cherry Valley limestone which underlies a large portion of north central New York contains a connate water with high concentrations of ammonia, hydrogen sulphide and the chlorides of calcium, magnesium and sodium. A number of questions were immediately raised on various aspects of the technical feasibility of the project. Of major concern was the buildup of insolubles adjacent to the bore of the injection well. Another pertinent question was the carryover in the displaced liquor of finely-divided, mechanically-suspended particles. Criticism was leveled at the inclusion of sewage. Engineering studies were started by the company's Mineral & Mines Development Department and on April 3, 1961 a preliminary feasibility report was issued.

Jan 1, 1973

By Matthew Spedding

The complex nature of the carboniferous measures prevailing in the U.K. has dictated the types of mining required to exploit the coal seams. Most mines in Britain are referred to as deep mines in the sense that they operate at depths of 1800 - 3000 feet. The main system of coal transport to the surface is by vertical shafts which intersect the workable seams which at times number between 4 and 5. As mining has been practiced in most of the major coalfields in the U.K. for well over 100 years, with the initial extraction of the shallower and more profitable seams, the present management have been left a legacy of indiscriminate extraction which severely hampers their efforts to maximise the mine layouts. There is no single standard design of mining layout capable of meeting the wide variety of conditions which exist in the British coalfields. Mining layouts are subject to fixed and variable parameters. In discussing multi-seam working, the main parameter must be the effect of old workings above and below the seam to be extracted. There is a distinct lack of reliable information which would enable layouts to be designed to completely avoid or control these destructive forces. The guidelines are, therefore, mostly empirical.

Jan 1, 1977

By A. Wang

This paper defines the elements of a basic economic model for decision-making when considering a methane drainage system for an underground coal mine. A drainage system will require significant capital and operating expenses; hence the decision to utilize drainage must be made carefully. The model outlines the basic structure of decision-making and considers the costs and benefits when the methane is marketed and when the methane is vented to the atmosphere. The effects on mine safety and the dust levels in the mine are also considered, both in a general format and as economic variables. Sources of information for executing this decision-making are provided for an actual mine decision.

Jan 1, 1997

By Hetland Donald L.

Regional Tertiary formations and basins of local sedimentation which contain uranium deposits west of the Rocky Mountains are mainly of Oligocene, Miocene, and Pliocene age (fig. 1). The host rocks have been derived mainly from intrusive and extrusive igneous rock. The major host formations which cover broad geographic areas include the Esmeralda, Truckee, Humboldt, Thousand Creeks, Payette, Panaca, Cedarville, Coso, and San Joaquin Formations. Local areas of Tertiary sedimentation containing uranium deposits occur near Yuma, Safford and Artillery Peak, Arizona; Dillon and Canyon Ferry, Montana; Spokane Indian Reservation and Pend Orielle River, Washington; Topaz Mountain, Utah; Stanley Basin, Idaho; and Sonora Pass, California. Uranium deposits in these sediments have been classified into five categories based on environment (fig. 2). They are: (1) Deposits in lake sediments consisting mainly of water-laid tuffs; (2) Deposits in lake sediments intruded by volcanic plugs; (3) Deposits in lake sediments interbedded with arkoses near batholiths; (4) Deposits in coarse volcanic sediments in local sedimentary basins; (5) Deposits in arkosic conglomerates in local sedimentary basins.

Jan 1, 1969

By M. M. Botz

Cyanidation tailings disposed of in a surface impoundment experience a loss of cyanide due to natural attenuation, which frequently reduces the cyanide concentration to very low levels. Quantifying cyanide losses in terms of impoundment geometry, local weather conditions and feed-solution chemistry has been largely empirical in spite of the fact that, in many cases, mining operations rely on surface impoundments to reduce cyanide to below an internally regulated concentration or below an effluent limitation. To permit a quantitative evaluation of cyanide losses in an impoundment, a computer simulation was developed to estimate the losses of free, weak acid dissociable (WAD) and total cyanide due to dissociation, photolysis and volatilization. Results of the model are compared with data collected for a North American tailings impoundment in 1998.

Jan 1, 2000

By D. Malhotra

Gold and silver ores are generally leached in weak cyanide solutions for recovery of precious metals. However, pretreatment of refractory ores requires flotation to concentrate the precious- metal minerals. Also, flotation is a common concentration technique for recovering precious metals as byproducts in sulfide-mineral flotation circuits. The present paper reviews current plant practice and future challenges for precious metal recovery.

Jan 1, 1999

By Terry Ramsey, N. Finkelstein

INTRODUCTION The Cyprus Pima Mine is located 20 miles southwest of Tucson, Arizona and about fifty miles north of the Mexican border. The Cyprus Pima orebody was discovered in 1950. Feasibility studies were begun in 1952 employing underground development. Economic studies showed open pit operations to be feasible and stripping of overburden was begun in late 1955. The first ore was reached in October of 1956. A 3,000 tpd (tons per day) concentrator was completed and began operation January 1, 1957. From these beginnings, Cyprus Pima Mining Company has expanded into a plant processing approximately 54,000 to 56,000 tpd. Four expansions were required to bring the plant up to its present capacity. Each expansion incorporated what had been learned in previous operation of the plant. The first expansion was completed in August of 1963 doubling design capacity to 6,000 tpd. In reality, because of softer than average ore, capacity was closer to 8,000 tpd. Expansion I1 was completed in July 1966 bringing design capacity to 18,000 tpd. Expansion I11 followed immediately. Completed in the summer of 1967, this expansion increased the design capacity to 30,000 tpd. The actual dry tonnage of this portion of the operation in 1974 averaged 38,400 tpd, again, primarily as the result of treating softer than average ore. The latest expansion (Expansion IV), completed in December 1971 and utilizing a semi-autogenous grinding circuit, is located in a separate building (Mill 11) approximately 200 yards southeast of the original mill (Mill I). Expansion IV was designed for 14,000 tpd, but after circuit modifications, averaged 16,500 tpd in 1974.

Jan 1, 1976

By H. Maleki, G. Tetreault

This study was initiated by the US Bureau of Land Management (BLM) to develop guidelines for determining the maximum economic recovery of resources in coal mines. The work was in response to a requirement in the Mineral Leasing Act of 1920 and Federal regulations. The intent was to address the economic rainability of small, irregular reserves in existing longwall mines. In particular, there was a need to determine if room- and-pillar mining using a continuous miner (CM) was economically sound or whether unconventional (short or odd-shaped) longwalls could be used to recover small coal reserves economically. Small reserves, called "widgets " are left in longwall mines on one side of the mains near outcrops and adverse geological conditions or near any other location where reserve geometry does not lend itself to mining with a rectangular longwall panel. The work included the analysis of the geologic, geotechnical and economic factors that influence the recovery of small coal reserves; the analysis of historic changes in supply, demand and coal prices; the development of typical cost models for room-and-pillar and longwall mines; and the development of a practical methodology for determining maximum economic recovery. The methodology included an evaluation of the ratio of coal mined during longwall mining to that mined for development (LDR), as well as costs of maintaining coal quality depending on market conditions. The LDR is a good indicator of mine efficiency and overall coal recovery in modern longwall mines and, thus, is used to evaluate the increased costs associated with adding new development sections for extraction of small reserves. The study examines the economic feasibility of using unconventional longwalls for the recovery of medium-sized reserves, depending on site-specific geologic and geometric conditions.

Jan 1, 2002

By Richard R. Klimpel

This paper reviews the use of sulfide mineral collectors in industrial flotation practice. The approach of the paper is to characterize sulfide mineral collectors in a number of ways, including by chemical structure, by influences with different classes of mineralogy, by interactions with particle size, and by interactions with frother type.

Jan 1, 1999

A number of factors affecting the properties of cemented aggregate fill (CAF), particularly its strength development have been studied through a series of laboratory investigations carried out at the Western Australian School of Mines in the Western Australia in recent years. The outcomes of these investigations indicate that apart from cement dosage, aggregate particle size distribution, aggregate quality, additional fine materials, water salinity, admixture dosage and sample scaling all contribute significantly to the development of cemented aggregate fill strength.

Jan 1, 2001

By Christophe Bragard, Jason Choi, William H. Hansmire

This case history provides a physical benchmark of tunneling technology progress comparing an old hand-mined tunnel to a modern 20-ft-diameter EPB TBM that mined in the same ground. This rare opportunity to see how tunnels were constructed many years ago occurred when an old 10-ft-diameter storm drain tunnel in the way of os Angeles subway construction was demolished and replaced with obas berglass pipe. Steel rib and lagging initial support was exposed showing solid-sawn 2" × 12" × 48" redwood lagging. This paper documents the as-built old tunnel, how it was successfully replaced, and some lessons learned.

Jun 23, 2024

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By Ke Yang

In Chinese coal mines, extraction of deep, highly gassy soft coal seams sandwiched between soft floor and soft roof in complicated geology is commonly encountered. How to safely and efficiently excavate such seams is a very significant and important problem. It has been a focused research area in recent years. By combining the characteristics of fully mechanized longwall mining methods such as large cutting height and mining along the dip, an integrated method and technologies for the Zhangji Coal Mine were developed. This technology includes the design of a complicated geological exploration system, optimization of mining method and working face parameters, control of rock pressure and high levels of gas, reliability model of the production system, and selection and compatibility of equipment. Engineering practice shows that the integrated technology was successful in mining these complicated seams. This study not only enriches the mining method, but also improves the coal mining practice, especially ensuring both safety and productivity under complicated geological conditions.

Jan 1, 2009

By J. L. Ellenberger, P. W. Jeran

A deep longwall coal mine was instrumented with a three-dimensional microseismic system in order to help determine the exact strata mechanics associated with the rock failure, redistribution of stress and the associated gob formation from the longwall. Overall, 5,000 well calibrated seismic events were recorded during the mining of the panel. Analysis of these events showed a close correlation between the seismic activity and advance rate, and that the majority of the recorded seismic activity occurs in the immediate area of the advancing longwall face.

Jan 1, 2002

By Gordon R. Luster

Mineral-processing plants commonly rely on homogenization and proportioning facilities to reduce the variability of incoming raw materials and to blend different materials together to satisfy quality specifications. To determine appropriate designs for these facilities, plant designers need information about the variability of the mined materials, measured as the materials enter the plant. But if the materials to be mined in the future differ greatly from those used in the past, only information extracted from exploratory drilling of the materials in the around may be available. Fortunately, useful information for plant design may still be obtained by combining simulated mineral deposits with simulations of likely mining procedures. The output of a mining simulation is a time series of simulated raw-material characteristics that should mimic the behavior of the real materials to be delivered to the plant in the future. This paper shows how conditional simulations of coregionalized ore grades can furnish information useful in the design of homogenization and proportioning systems.

Jan 1, 1986

By Ronald C. Bethard, Kenneth W. Ely

The liberation of methane during underground coal mining causes serious safety concerns. During a mining cycle, with mechanized mining equipment, thousands of cubic feet of methane are released from coal seams, discharged to return air courses, and vented to the atmosphere through mine fans. This has been the traditional way of removing the explosive hazards of methane gas from the mine. Through horizontal and vertical degasification techniques, this hazard can often be handled in an equally safe and much more profitable manner. Basically, degasification allows for the controlled reduction of inseam methane content of coal prior to its mining. It is the responsibility of mine management to evaluate these degasification programs and ensure that the program itself does not introduce some new risk to the mining process. The removal of methane gas from underground coal mines using horizontal and vertical degasification is a relatively new concept. Products and systems used in degasification continue to evolve. Site conditions vary also, so no one system or equipment can be said to be the safe answer for degasification in all situations. A constant process of cooperation and evaluation by mining and degasification management should result in a safer and more profitable mine.

Jan 1, 1989

By G. Hargrave, K. W. Moloney, M. R. Stokes

In recent years drivage advance rates in the UK have in- creased from 35m per week in the 1980's to 100/150m per week possible today. These extended rates of advance have resulted in an increase in the potential methane, dust and heat generation at the drivage face. In order to disperse this additional pollutant load requires an increase of fresh air at the face. Although advance rates have changed, current auxiliary ventilation practice has not. UK mining law requires that the fresh air must be delivered to within 5m of the face. This has lead to the wide spread use of overlap auxiliary systems, since a pure forcing system set at this distance would lead to excessive airborne dust. UK mining law does not at present consider on-board mounted exhaust scrubber fans to constitute an effective overlap fan within mechanised drivages. In an attempt to determine whether working conditions could be safely and economically improved within mechanised drivages, a series of preliminary full scale gallery trials were con- ducted. A summary of the principal findings of these trials are presented together with an outline of a series of representative CFD simulations, scale model experiments.

Jan 1, 1997