Search Documents

By H. Appiah

Small scale mining (SSM) has been going on for a long time in Ghana. SSM was legalized by the PNDC Law 218, 1989. Since then there have been numerous gains from the SSM industry. The SSM is organized locally by the concession owner who engages people to work for the gold which he buys. Small scale miners (SSMs) use crudely made sluices in Ghana and, therefore, their production falls below what is expected. The SSMs work in groups and not as cooperatives, as they do in Brazil and other Latin American countries. Legalization of SSM has curbed gold smuggling considerably because a gold marketing entity is available. SSM poses certain environmental problems like pollution of water bodies and soils by mercury and indiscriminate digging of pits.

Jan 1, 1998

By E. Laine

Rock density determinations are necessary for ore resource evaluations from estimated block grades in g/t. Rock density depends on the mineral composition and, thus, it is specific for each rock type. The rock density distributions for different rock types are often symmetric. Hence, the arithmetic mean is a good approximation for the average density for lithological units. However, there may exist spatial variation in density values due to alteration, fracturing and original heterogeneities such as layering. This study compares the kriged density model with the one with constant density values for different lithological units in the evaluation of metal amounts in rock blocks. The case study consisted of rock densities measured from the drill cores at Ahmavaara PGE deposit in northern Finland. The used Ni contents were simulated in accordance with the spatial distribution of rock densities. The Ni amounts in 2x2x2 m3blocks are higher for the kriged densities than for the average densities. The difference is increasing with the increasing metal amounts due to the nonlinear correlation between Ni content and rock density. The final effect on the resource estimation depends on the cutt off grade and prices of the metal, for example, for a very valuable metal the small differences are significant

Jan 1, 2003

By L. Lehasa

The purpose of the project was to investigate the challenges faced by Khutala Colliery pertaining to underground road construction and maintenance. Furthermore the influence of these challenges on productivity and safety requirements were taken into consideration. The operating standards required for the construction and maintenance of the 2 seam road transport infrastructure was investigated, together with reasons why the standards of operating procedure are not met. The Code of Practice put in place by Khutala Colliery was used to view the standard operating procedures. Leading practices on underground road construction were researched. The project aims to discover the gaps that Khutala Colliery must bridge to implement enhanced practices with regards to underground road construction. During the period of study, observations were carried out to determine whether the road construction standards of operating procedure were being adhered to at all times for both road construction and road maintenance. Khutala Colliery has put in place a traffic management plan, which includes safety practices and work policies that must be adhered to while travelling on underground transport roads.

Jan 1, 2012

Geologists in some underground gold mines collect grab samples from broken ore piles or trucks as a method of grade control. It is often known as muck sampling. Generally, the goal of grab sampling is to try and reconcile the mined grade at the ore source to the predicted grade and/or predict the mill feed grade. The mass of the sample collected is limited by health and safety issues, as well as by the capacity of the laboratory to process the samples within a given time frame. In general terms, grab sampling is known to be problematic because samplers tend to oversample the fines, and/or pick out high-grade fragments; surface sampling of piles does not test material within the pile; muck piles in development drives/faces are likely to be zoned due to the blasting sequence; high or low-grade material may preferentially segregate in the pile during mucking; the five per cent mass reject size of the material in muck piles is very large from underground blasting; some correlation usually exists whereby the larger fragments are enriched or depleted in the critical component of value; and the average error made in estimating the true stockpile grade is likely to be high. The method is prone to chronic fundamental sampling, grouping and segregation, delimitation, and extraction errors. Substantial warnings must be given about the use of grab sampling for grade control in gold mines. The method may appear to work sometimes, which can be attributed to a fine gold particle sizing and more disseminated distribution. As with all sampling methods, its appropriateness must be determined by ore characterization and heterogeneity testing to ensure the method suits the ore type.

Jan 1, 2010

By P. E. Hand

Coal is a complex heterogeneous commodity that can be mined in a number of ways and needs to be processed to a homogeneous quality that satisfies the customer?s requirements, while attempting to maximize revenues. Only a small proportion of coal is suitable for metallurgical use. Export coals cover a wide range of qualities and some coals can be used optimally in the raw state for energy production. Critical quality parameters vary and can be a combination of heat value, ash, volatiles, sulphur, phosphorus, sizing, amongst others. The level of beneficiation is generally dictated by the washability of the coal, mining contamination, and the target product quality. The steps in the coal chain covered in this paper comprise exploration, mining selections, production, the washing process, and product delivery. Many points of sampling are needed to maximize yield at the correct quality, and some of these will be described in the paper. Keywords coal chain, coal beneficiation, sampling.

Jan 1, 2014

By V. Arslan

In this study, effects of the inert constituents, such as ash, and the effect of blending coals with differing rank and composition on the plasticity of coal blends were investigated. The reference coal originated from the Zonguldak region, in the north-west part of Turkey. Firstly, the effect of coal ash on the plasticity of Zonguldak coal was determined. Secondly, the relationship between the plastic properties of the individual coals and those of the blended coals were identified. Some important relations were found, related to the characteristics of the individual coals. Ultimately, the manner in which the plasticity of Zonguldak coal was affected by blending with low volatile coals was investigated. Keywords: coal blending, coal plasticity, coke, fluidity, rank.

Jan 1, 2006

By N. Reddy

The influence of local geology and rock mass characteristics on deformations during a rockburst caused by a controlled blast was studied. This was done by means of visual examination, mapping and photography both before and after the blast. We found that the ejected material was bounded mostly by fractures associated with the bow-wave fracturing and bedding surfaces and that existed prior to the blast. Most of the damage was caused by shake-out. This information is important input for the design of rockburst resistant support systems under conditions of moderate stress.

Jan 1, 2001

By D. P. Roberts

The stoping of platinum orebodies in the Bushveld has in the past been accomplished by using in-stope pillars to ensure stability of the workings. In the future, the use of continuous mining machines to mine the platinum orebodies is probable. It is not envisaged that such machines will cut in-stope pillars. This paper describes the alternative support systems that will replace the pillars and the stope geometries that will be required for this type of mining. The paper describes how the support resistance provided by in-stope pillars in current mining was determined and then evaluates support systems that can substitute for these pillars. Conceptual layouts based on existing breast mining layouts are presented. The layouts consist of panels of up to 100 m face length between rigid strike stabilizing pillars. A number of design charts are then proposed that allow for the design of appropriate support systems.

Jan 1, 2005

Gravity-driven rock falls account for a large proportion of all fatalities and injuries in underground mines. Potentially unstable blocks of rock are found in the hanging wall of excavations, which may be delineated by natural joints or stress fractures. These blocks, referred to as keyblocks, will fail if their weight exceeds the support capacity or if they are located between support units. This paper describes a computer program which simulates blocks in the hanging wall of an excavation based on measured properties of fractures and joints. Keyblocks are identified and placed at random locations in a predefined excavation. The keyblocks are tested against the support to determine whether they fail the support, drop out between the support or are stable. By repeating the procedure several thousand times, statistics of the probability of failure of the keyblocks are obtained. This approach allows the relative hazard associated with different types of support or excavation orientations to be obtained. It is concluded that a probabilistic approach is suitable for the evaluation of supports effectiveness in situations where large numbers of discontinuities or stress fractures are exposed in excavations.

Jan 1, 1998

By P. W. J. van Rensburg

The Institute was privileged to receive an invitation from the Armaments Corporation of South Africa (Armscor) for members to visit one of their plants. As these are factories, the number of visitors who could be accommodated was limited. As the opportunity seldom arises to learn something of this very large industry, there was great interest among members and many were disappointed in not being able to go. Underwater mining The 16th Annual Underwater Mining Institute will be held at Halifax, Nova Scotia, Canada, from 20th to 23rd October, 1985.

Jan 1, 1985

By S. E. Olsen, M. Tangstad

The main source of Mn in raw materials for SiMn production is Mn-ore and Mn-rich slag from the high carbon FeMn production. The amount of slag per tonne of SiMn metal is mainly determined by the ore/slag ratio. Increasing share of FeMn slag at expense of Mn-ore will lead to larger slag/metal ratio in the SiMn process. High volume of slag leads to an increased consumption of energy and probably to higher losses of metal inclusions in the final slag. Excavation of a SiMn furnace has shown that only modest pre-reduction of Mn-ore with CO gas seems to be obtained. Nearly all reduction of MnO was finished at the top of the cokebed. Dissolution and reduction of quartz obviously takes place in the cokebed zone after the main reduction of manganese oxide is finished. Probably the ?pick up? of Si in the metal is quite fast and takes place as the metal trickles down through the cokebed towards the metal bath. The distribution of Si between SiMn alloys and multicomponent MnO-SiO2-CaO-Al2O3-MgO slags is mainly determined by the process temperature, the silica content of the slag and its R-ratio = (CaO+MgO)/Al2O3. As an example, the equilibrium content of Si in the alloy will increase by about 6 % if the R-ratio is reduced from 2 to 1, provided constant temperature and silica content. The effect of temperature is also considerable. The equilibrium content of silicon will increase by approximately 6 % per 50°C in the temperature range 1550°C to 1700°C. The equilibrium content of MnO in SiMn slags depends first of all on the temperature and secondly on the silica content of the slag. At 1600°C the MnO content decreases from about 9 % at silica saturation to a minimum of about 3-4% when the silica content is reduced to about 40-45%.

Jan 1, 2004

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

By B. Unver

Effective strata control is a prerequisite for maintaining an efficient mining operation. If the strata in the vicinity of an opening are not controlled effectively, it is impossible to perform a safe, efficient and economical operation. In this paper, the reasons and outcome of instability problems observed in roadways opened in clay and marl at the Bolu Colliery of Yeni Çeltek Establishment are investigated. Roadways under examination were located in a syncline causing high residual tectonic stresses. Factors affecting the instability have been studied thoroughly by examining geology and tectonics of the area, establishing convergence measuring stations to understand in situ behaviour of supports and laboratory tests to determine engineering properties of samples taken from nearby convergence measurement stations. As a conclusion, a new production strategy and a new support system are recommended to maintain stability.

Jan 1, 1999

By D. McCarthy

Contract is a PC-based software program designed to satisfy the main features that have been identified to be lacking from cost estimation systems currently in place in the Australian coal industry. Contract was developed in conjunction with an Australian contracting company to refine the existing core structure used by the company for project evaluation. The key feature of Contract is the availability of analysis functions to explore multiple options within a contract project by altering identified variables. The ability to update project files has been incorporated into Contract to ensure that it is user-friendly and relatively simple to use. Lists of mining equipment and consumables are stored in MS ACCESS database files, along with the supplier details for each item. Each time a project is initiated there is a dynamic link to the database files and the most recent current information is retrieved and linked with the project. Contract provides an option to calculate the changes in metre unit cost as a function of the average development cost. Keywords: Contracting, cost estimation, sensitivity analysis.

Jan 1, 2003

By M. R. Bitarafan

Mining method selection is the first and most important problem in mine design. In this selection some of the parameters such as geological and geotechnical properties, economic parameters and geographical factors are involved. The mining engineer must balance the input parameters and select the method that appears to be the most suitable; mining method selection is both an art and a science. Distinguishing all parameters that have an effect in mining method selection and in the determination of weighting factors of any parameter is a difficult task in an ordinary environment. This paper attempts to determine important parameters that impact on the mining method selection and demonstrates the calculation of the weighting factors for each selected parameter. This study has been directed to the research of a methodology for the selection of an optimal mining method. Different fuzzy methods are presented as an innovative tool for criteria aggregation in mining decision problems. Two methods of fuzzy multiple criteria decision making are used for selecting the optimal method with which to mine anomaly No. 3 of the Gol-Gohar iron mine. This paper finally presents a comparison of the selection methodologies and further discusses the most appropriate method investigated.

Jan 1, 2004

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering)degree Identification of non-linear systems can be a daunting task and in the process industries the problem is complicated considerably by the presence of noise from various sources, non-stationarity of the data and intermittence, such as observed in particulate flows. Traditional methods, such as frequency analysis and linear model-ling do not handle these systems well. Similar problems arise with the application of non-linear theory developed over the last few decades, where much of the analysis depends on embedding of the data in a phase space or pseudophase space, since these methods were not originally designed to deal with noisy systems. In contrast, singular spectrum analysis is a method which can be used to identify structure and distinguish noise from important information in multivariate data, such as the trajectory matrices of time series measurements. It provides an orthogonal basis onto which the data can be transformed, so that components of the time series can be investigated individually. With Monte Carlo methods, the components can be compared with those from linear surrogate data in order to identify possibly non-linearities in the data. In this paper, this versatile technique is briefly explained and illustrated by means of case studies.

Jan 1, 2003

Electrochemical measurements are presented on electro-deoxidation of silica in molten calcium chloride at 900°C, with porous silica pellets as starting material. Measurements during pre-electrolysis (to remove water from the melt) showed electrochemical noise, which is consistent with the evolution of hydrogen. Throughout, the dominant anodic reaction appears to be CO2formation, based on the observed potential at the anode, and measured anode wear. Because of the presence of dissolved CaO in the melt, some of the CO2 candissolve in the melt; the resulting calcium carbonate formation was confirmed by electrolyte analysis after reduction runs. Reduction of dissolved CO2 at the cathode is likely to contribute to the background current during the reduction process. For the electrode and cell configuration used here, most of the over potential arises from polarization of the anode, and ohmic potential drop in the electrolyte.

Jan 1, 2006

By T. O. Hagan

Analyses of accident records show that a better understanding of very basic strata control principles and practices, by production personnel, will improve worker safety. Workers, lack of knowledge, with respect to aspects of strata control, increases their exposure to such strata control risks. The primary objective of the Safety in Mines Research Advisory Committee (SIMRAC) project 02 02 07 was to develop tools for the transfer of strata control knowledge. Four such tools were developed, three of which focused on illiterate underground mine team members who are not yet able to take advantage of the Mining Qualifications Authority (MQA) learning process (see project outcomes 2, 3 and 4 below). The tools were designed to equip these workers with sufficient knowledge and ability to work safely underground until such time as they can take advantage of the MQA system. Project outcomes: 1 A four-minute video using animation to illustrate the causes and prevention of falls of roof in South African collieries. 2 Software to demonstrate the capability of reconstructing, interactively, accident scenes and actions that have taken place underground in stopes. 3 A strata control bridging course for illiterate mine team workers. 4 Small-scale wooden models that will be used to design life-size mock-up facilities to assist with the above mentioned bridging course. 5 Workshops and presentations to demonstrate the outcomes 1to 4 above.

Jan 1, 2005

By C. Sensogut

The phenomenon of spontaneous combustion is one of the major hazards encountered in underground coal mines both from the safety aspects and on economic grounds. Every occurrence, however small, if not tackled effectively in the early stages can develop into open fire, or explosion of gas or coal dust. In terms of economy, even dealing with small incidents may be costly in terms of labour and materials, and in case of a sealing off of a district being necessitated, the loss of face equipment and sterilization of reserves is potentially great. Therefore, expense and effort in prevention and detection of such heating, together with a high state of readiness for dealing with likely event, is completely justified and may be considered as a sound investment. In order to achieve this investment, it may be worth to pinpoint the centre of the fire occurring due to autogenously heating which is supposed to be great assistance to inert it at a least cost and time. Therefore, it is the aim of this work to model the spontaneous combustion in the goaf.

Jan 1, 2002

By B. A. Day

The traditional view taken of commodity prices is that they are cyclical, with strong demand boosting prices and attracting new suppliers. The resulting increased supply pushes prices down with consequent exit of the higher cost producers. And so the process repeats itself. Little attention is given to shifts in underlying global issues and their effect on the traditional process which is seen as being controlled by ?amorphous? market forces with producers profiting from the good times and trying to survive in the bad.. The questions posed are: does this still apply and will it apply into the future? What new factors are affecting the cycles? Can we expect to find the traditional commodity cycles repeated in the 21stcentury? Are producers powerless within the forces of the cycles? Forces likely to affect future commodity prices will be suggested, using gold, zinc, copper, tin and coal as case studies. The long-term downward trend in the real price of commodities is identified.

Jan 1, 2000