Search Documents

By David C. Oyler, Dennis R. Dolinar, Christopher Mark, Craig S. Compton

Fully-grouted roof bolts comprise more than 80% of the primary roof supports used in U.S. coal mines. However, nearly 1,500 MSHA reportable, non-injury roof falls occur each year, and most of these are attributable to failure of the roof bolt system. Anchorage failure is one failure mechanism for fully-grouted bolts. As roof deformation works its way upward, the bolts can become heavily loaded near their upper ends. If the applied load exceeds the anchorage, the bolts will simply pull out. Research dating back 30 yrs indicates that this type of anchorage failure is most likely when the roof rock is weak, just where roof support is most critical. In soft shale or coal roof, the small amount of data available in the literature indicates that 20-30 in of resin anchorage may be required to achieve the full capacity of the bolt. In other words, the “full resistance zone” of a 60 in bolt may actually be just 30-40 in. Despite its potential importance, there is no widely accepted anchorage test for fully grouted bolts. Standard pull tests have sometimes been employed, but they provide no information on the anchorage near the top of the bolt. An alternative, first described more than 25 yrs ago in the U.S., is the short-encapsulation pull test (SEPT). With this test, the bolt is installed with only a short (1 ft or less) tube of resin. In recent years variations of this test have become international standards. v

By J. B. Stott

The performance of an adiabatic calorimeter for measuring heats of oxidation of coal is assessed and suggestions made for its improvement and calibration. The use of magnetic analysers for measuring small oxygen deficiencies in air is described and three different methods of measuring the output for such a meter are characterised. The occurrence of spontaneous heating in an 800 tonne heap of Wyoming coal is briefly described. The major part of the report deals with the oxidation of Pittsburgh seam and Wyoming subbituminous coal and describes an experiment in which 1 tonne of Wyoming coal is stored in a 5 metre long insulated container whilst air was passed through. Temperature rises, rates of oxygen absorption and gas compositions of the air stream were measured. The report relates the results of these-experiments to a theory of spontaneous heating developed by Stott and Quan which stresses the importance of the moisture content of the coal and the relationship between the heat necessary to evaporate this water to the heat available from coal oxidation. The work was carried out over a five month period and the emphasis is on demonstrating the effects of moisture transfer and confirming the theory of Stott and Quan.

Jan 1, 1980

By George L. Gates

[When clays are mixed with water to -.,tee mud fluids for use in trilling wells for nil and --ac b ;l-,e rotary method the liquid mixtures have certain physical characteristics that vary with the quantity and size of their inherent solid particles. All naturally occurring clays contain variable quantities of particles of different sizes ranging from relatively coarse (sands) through -,.tedium (silt) to fine materials of colloidal dimensions. Tie colloid content is extremely important 2.s a desirable _.'ale constituent of mud fl-z to fit well drilling. ';'it:-out colloids the souk?;,' in a mud fluid wouldr rapidly, end ti-c-and. wall-building qualitites of the' fl,-,id would l ..o r re 1 impaired. Mud .fluid.^ with insufficient quantities of colloids also are lacking in "lubricating" g listen, and it is, to ° min casing in, -)re holes drilled with such fluids.]

Jan 1, 1941

By G. D. Bakulev

Economic Importance of Gasification of Fuel and Brief Outline of Development of Underground Gasification of Coal in the U.S.S.R. The underground gasification of fuel offers a number of economic and social advantages, principally the following: 1. Full automation of labor-consuming coal-mining processes, which resist complex mechanization and automation, particularly shaft mining. 2. Elimination of hard, dangerous, and often unhealthful mining work. 3. Creation of hygienic conditions for personnel employed in gas production, as well as for those in boiler rooms using the gas. 4. Possibility of automation of complex production processes of thermal-electric powerplants using underground gas with economic installations for steam production. 5. Economic operation of thermal-electric powerplants constructed in the areas of underground-gas production. 6. Release of railroads from the burden of transporting fuel. 7. Extension of the power base of some areas in need of fuel and of the economy as a whole due to use of fuel deposits not amenable to normal mining practices. 8. Reduction of capital investments per unit of energy produced in the form of fuel. 9. Substantial increase in general labor productivity. 10. Possibility of substantial reduction in the cost of fuel produced and of electric power produced from underground gas.

Jan 1, 1962

By Clayton R. Morlock

Airblasts have been monitored at four coal strip mines and at a limestone quarry. Thirty-seven production blasts have been monitored with three seismographs, resulting in one hundred and eleven complete air pressure records. Instrumentation selection use is described. Data analysis includes an assessment of the predictability of peak overpressures by means of the cube root scaled distance law. It is found that predictability for the cases studied here is not good. An extensive discussion of possible explanations is included. A detailed analysis of the frequency content of the observed airblasts, of considerable importance in evaluating potential annoyance problems, has been made for all records. A computer program has been written to simulate airblasts induced by multiple-hole blasts. A series of small experimental blasts have been detonated and monitored in order to allow an assessment of the program. It is clear that airblasts, especially when induced by very small charges and monitored at very close distances, are highly sensitive to detonation times. Retrofitting of airblast records occasionally was possible, but considerably improved field work is required to validate or refute the computer model.

Jan 1, 1983

This study assesses whether Narragansett Basin coal deposits could be developed commercially in the near future. To do this, we identify the potential market for the coal, assess the price these users would be willing to pay for Narragansett coal, and this price to the expected costs of producing Narragansett coal. The study concludes that the major market, New England utilities, could burn bituminous coal from Pennsylvania or West Virginia at a lower total cost than Narragansett Basin coal, assuming expected mining conditions and emission policies. Therefore, the study concludes that Narragansett Basin coal resources could not be developed economically in the next ten years.

Jan 1, 1979

By Ronald P. Hollenbeck

Shales in the Appalachian Region of Kentucky and Tennessee were sampled and tested to determine their use as raw materials for the manufacture of lightweight aggregate by the rotary-kiln method. Nine samples were obtained from eastern Kentucky and 143 samples were obtained from eastern Tennessee. As a result of preliminary testing of these samples, two sources in eastern Kentucky and 11 sources in eastern Tennessee were resampled for rotary-kiln tests. The rotary-kiln tests showed the two sources in Kentucky and seven sources in Tennessee contained shale that would produce satisfactory aggregate. Lightweight aggregate processed from these nine sources was tested in concrete shapes and was found to be suitable for use in structural concrete.

Jan 1, 1968

By Zsuzsanna Zborovszky

[Certain chapters of the tentative document entitled, "Test Requirements for instruments & Apparatus to be Considered for MESA Intrinsically Safe Certification" are evaluated and supporting data are presented on certain key issues with the purpose of helping the regulatory agency in improving the above document. The subjects discussed in detail are: hot wire ignition with W and BeCu wires; the most sensitive methane-air :and propane air ratio; the ignition limits for inductive-resistive circuits in 8.3°; methane-air mixtures in the 24-OV, 100 mH-2 [ ]H range, the resistive ignition limit as a special case when L ? 0; the capacitive-resistive ignition limit representing a four ,dimensional problem is analyzed and discussed in general and the variation of the ignition limit using Vo and/or r2 as a parameter are determined experimentally. The ignition limit is also determined for the [r1 ,~ r2] = 0 case ("capacitor alone") and for the most dangerous capacitive resistive circuit combination. The ignition limits are below the limits proposed in the document. A survey of the different factors influencing the ignition is made as to their suitability to provide a constant safety factor. It is shown that a constant safety factor cannot be achieved. The best method for applying a safety factor appears to be the increase of initial pressure or use of other gas mixture. The revision of the safety factor concept and ignition limit curves is recommended.]

Jan 1, 1980

By M. Vanpée, H. G. Wolfhard

Jets of hot gases issuing into explosive gaseous mixtures are efficient agents of ignition . The ignition temperature is defined as the temperature of the jet as it enters the cold explosive mixture which is just high enough to produce ignition . Such data have been published recently.5/ The investigators note especially that no correlation seems to exist between hot - gas ignition temperatures and spontaneous ignition temperatures , although there is a rather loose relation with limit flame temperatures . Before a more quantitative theory of the hot - gas ignition process can be attempted effectively , several questions must be answered : ( 1 ) Can the reactions leading to ignition be described by an Arrhenius type activation energy? ( 2 ) Is ignition preceded by an induction period ? ( 3 ) What is the rate - determining process of the ignition ? (4) And how does turbulence affect this type of ignition ?

Jul 1, 1960

By F. S. Crawford

This study was made to find methods of preventing back strains, among workers in brick plants, however, the information should apply to other industries that employ hand labor too process materials. The report is based on information in letters from. Bureau of Mines engineers and other safety men in the United States who visited numerous brick plants. Back strains, as wall as hernias and other muscular strains, result when certain body structures are subjected to strains greater than, they can withstand. Such breakdowns may be prevented simply by not straining these body structures. This is simple in theory but complicated in practice. It requires primary education of new workers and reeducation of older workers in the best method of lifting, preemployment physical. examinations to select employees for the jobs that require constant lifting, all possible mechanization of material-handling operations, relocation of machinery, and elevation of working surfaces to reduce to a minimum the muscular effort the workers must exert to perform operations impossible to mechanize. Accidents of any kind are a total bee for the American economy and decrease productivity; whereas mechanization raises the level of productivity and constitutes progress toward total safety. Heavy lifting should be done mechanically whenever possible, saving the men to direct the machines. This is an essential step in preventing strain accidents.

Jan 1, 1953

By E. D. Calvert

The room temperature tensile properties of commercially pure titanium and seven titanium alloys prepared by skull casting were determined in the as-cast and heat-treated conditions. Data were compared with property data from tensile tests on wrought alloys of the same compositions in the as-worked and heat-treated conditions. The alloys evaluated were Ti-5Al-2.5Sn, Ti-6Al-4V, Ti-6Al-4V-lSi, Ti-6A1-2Sn-4Zr-2Mo, Ti-6A1-6V-4Zr-4Mo, Ti-6A1-6V-2Sn, and Ti-11.5Mo-6Zr-4.5Sn. Test specimens were prepared from both static and centrifugal castings and from plate fabricated by forging and rolling vacuum-melted ingots. The data indicate that the alpha and alpha-beta alloys have strength properties in the as-cast condition that are reasonably close to the strength properties of their wrought counterparts in the as-worked condition. An exception to this was the Ti-6A1-6V-4Zr-4Mo alloy for which insufficient data were available to form any firm conclusions. Fine-grained cast structures of Beta III (Ti-11.5Mo-6Zr-4.5Sn) were shown to be generally stronger in the as-cast condition than the wrought alloy in the as-worked condition except for the yield strength of one structure that was unusually low. Heat treatment of this alloy produced properties that were unpredictable. Indications are, however, that optimization of heat treatment parameters for each cast structure could produce strength properties equal to that of wrought materials.

Jan 1, 1974

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications.

Jan 1, 1963

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By William J. Campbell

This report describes a Bureau of Mines study undertaken to determine the applications and limitations of solution techniques as a general method of fluorescent X-ray spectrographic analysis. Systematic errors due to variations in particle size, surface preparation, and sample inhomogeneity are eliminated by the use of solutions. The range of applicability of fluorescent X-ray spectrography is increased in two ways: (1) Samples in the form of wire, filings, turnings, etc., can be analyzed as solutions, and (2) samples submitted as solutions can be analyzed as received 0 The lower limit of detectability varies from 0.14 gram per liter for sulfur, atomic number 16, to 0.0015 gram per liter for strontium, atomic number 38. Most elements have limits of detectability between 0.02 and 0.002 gram per liter.

Jan 1, 1959

By John C. Machisak

STATISTICAL data on injuries and employment pertinent to metal mines and to their mills, and/or processing plants are presented in this Information Circular for the calendar year 1960. The information pertains to metal mines, as well as ore-dressing plants and primary nonferrous smelters, refineries and reduction plants, and their auxiliary works. These data are voluntarily submitted annually to the Bureau of Mines by the operators, and contribute greatly toward the promotion of safety in the mineral industries. The data presented are classified according to the principal mineral produced and include information on copper, iron, lead-zinc, gold-silver lode, gold placer, uranium-vanadium and miscellaneous metals. A breakdown of miscellaneous metals by commodities is shown in table 19, page 41. The data also relate to workers engaged in production, exploration, development, construction, and maintenance and repair work, as well as supervisory personnel and office- workers at the mine or plant site. Injury and employment data at metal mines and metallurgical plants in the United States for 1960 are shown under the following general sections:

Jan 1, 1963

By Dana C. Reinke

Water well drillers are exposed to high levels of noise while working. NIOSH researchers have found that water well drillers are exposed to levels above 85dB (A) while performing certain tasks during a typical drilling job. Noise levels consistently over 85dB (A) during an 8–hour work shift are hazardous and can lead to hearing loss in workers. Finding ways to reduce noise exposure is difficult because of many factors. The work environment is constantly changing due to the location of jobs and environmental factors. The types of drill rigs required for drilling are expensive. Equipment can range from new to used (10 to 30+ years old). Drillers and owners can work together to prevent noise–induced hearing loss, and measures can be taken to reduce exposure to hazardous noise.[ ] Preventing hearing loss occurs through three stages. The first stage is removing noise from the source (i.e., drill rig). Various parts of a drill rig create noise besides the drilling rod. NIOSH researchers have examined noise levels of drill rigs. Some of the loudest parts of the drill rig include the compressor, engine, and cooling fan (Fig. 1). While removing the noise source from a worksite is ideal, the process would be expensive and difficult.[ ]

Jan 9, 2005

By John C. Edwards, Gene F. Friel

A series of liquid fuel fire experiments evaluated the comparative responses of five types of commercially available smoke detectors and a diffusion-mode carbon monoxide (CO) detector under normal and reduced airflow conditions based upon the alarm times of the detectors. These experiments were conducted in the Safety Research Coal Mine at the U.S. Bureau of Mines Pittsburgh Research Center. Two of the smoke detectors had manufacturer set alarms. For the other three smoke detectors, an alarm point was defined in terms of their background analog signal and the detector's electrical output noise under ambient conditions. A correlation was developed of the travel time of 5 ppm CO between pairs of CO detectors with the travel time calculated from entry and crosscut volumes and measured airflow. Based upon the relative performance of smoke detectors in this limited study, smoke detectors can be as effective as CO detectors for mine fire detection once identifiable alarm values are defined. Implementation of smoke detectors as part of an atmospheric mine monitoring system will improve mine safety.

Jan 1, 1996

By Mark K. Larson

A constitutive model for rock interfaces based on the principles of static fatigue is proposed. The model is applicable to weak rock or joints with cohesion. Friction and dilation are decreased as plastic work increases. At equilibrium, the creep time increases by one time-step interval, and interface cohesion at each node decreases according to a power function. A constant-load, direct-shear simulation showed that the model is cap- able of mimicking constant-rate and tertiary creep and predicting failure. Tests on core from a coal mine showed constant-rate and, sometimes, tertiary creep, but also weak transitory creep. The cohesion deterioration function may need modification to simulate primary-phase creep. If model parameters are known for a site, the model can predict the onset of tertiary creep and failure. Such predictions can help engineers make better entry design and support decisions, which will reduce the likelihood of roof falls and increase safety for underground miners.

By H. B. Carroll

This Bureau of Mines report evaluates the performance of commercially available portable instrumentation for the detection of carbon monoxide, carbon dioxide, oxygen, and methane at conditions simulating an industrial work atmosphere. Portable instrumentation included in the study was gas-detection tubes (length-of-stain and color intensity), catalytic detector, liquid absorption detectors, paramagnetic oxygen detector, galvanic detector, and pelement or hot-wire methane detectors. Evaluation of the instruments was in atmospheres with 50 and 80 percent relative humidities at 75° F and containing test gas concentrations of 0.1, 0.25, 0.50, 1.0, 1.5, and 2.0 times the thresh-old limit value. Correlation of the results from the portable gao analyzer with measurement from the standard instruments was made by calculating and plotting an estimated line of regression, prediction, and confidence limits and the correlation coefficient for each detector system. Relative humidity in the 50-to 80-percent range did not appear to contribute to instrumental uncertainties in either performance or operation. Considerable deviation in detection precision between the portable gas-detection systems and the standard systems was established, especially at the lower gas concentration levels. The main difference or inconsistency in toxic gas concentrations determined with length-of-stain tubes resulted from the observer's interpretation of the results rather than difference in the tubes themselves.

Jan 1, 1973