Search Documents

By B. Demoulin, J. Fontaine, R. Gabillard, P. Degauque

To realize a radiowave communication along mine galleries a few kilometers long without repeater, we show that it is possible to use a coaxial cable bearing an important surface transfer impedance like a transmission line with an inductive coupling to the transmitter and the receiver. We determine the electrical and geometrical constants of the cable and the optimal frequency.

Jan 1, 1973

By M. A. Trevits, S. W. Lambert

In this Bureau of Mines investigation, production was monitored for 1 year at over 30 coalbed gas-drainage boreholes located in Alabama, Pennsylvania, and West Virginia. Results indicate that the quality of data gathered from such wells can be improved greatly if potential problems are anticipated and prevented in the early stages of well production. Major water-monitoring problems include solids buildup, freezing, the presence of gas in surface waterlines, and improper pumping interval settings. Such problems may be avoided by incorporating in the original well design waterline filters, sand screens, separator tanks, and systems to automatically control pumping intervals. Problems related to measurement of coalbed gas flow include large quantities of water vapor contained in the gas, especially during winter months; freezing and subsequent obstruction of flow; sudden, uncontrolled release of gas pressure; and solids buildup in metering equipment. The installation of commercially available items, such as filters, separators, and insulation, and the thoughtful application of a basic knowledge of coalbed gas reservoir characteristics will prevent most production-monitoring problems.

Jan 1, 1978

By C. N. Schuette

"The production of silica and magnesia crucibles in the induction furnace was attempted and achieved in the laboratory of the Pacific Experiment Station of the United States Bureau of Mines. This work was undertaken at the request of other stations for laboratory crucibles of a certain specified wall thickness and capacity.The essential new parts of this work are the development of a technique for the high-frequency furnace production of silica crucibles of greater wall thickness than could be readily fabricated from commercial fused silica, and for heavy-walled magnesia. crucibles of great density and mechanical strength. A considerable bode of patent literature on the Production of fused silica ware in resistor-type furnaces was examined, but it furnished no significant help for the present problem. Similarly sintered magnesia refractories are often made for technical purposes, but for use at temperatures of 2000o C. or over, the material must be sintered at higher temperatures than can be attained by combustion firing, and the very great shrinkage encountered at these temperatures requires special methods. Small crucibles. of magnesia fused in the electric arc have been made by Tritton and Hansen,3 but the practical size of such containers is very limited.Many different methods of making crucibles in the induction furnace were tried before satisfactory results were obtained. The following description covers only the most satisfactory method, which produced crucibles of excellent quality in a reasonable time and with a moderate expenditure of power and materials."

Oct 1, 1929

Permit quicker, safer clearance of hang-ups in the ore passes and chutes of underground mines. Approach Develop a device that can be operated from a safe distance to explosively propel a projectile into the hang-up. How It Works The Hang-Up Clearance Module, consisting of a stand, steel disk, explosive charge, and aiming device, is placed at a location convenient for line of sight aiming at the hang-up. This placement can be more than 100 feet from the target. Once aimed, the charge is remotely detonated, and the disk is converted by explosive force into a slug and propelled to the hang-up, bringing it down. The steel disk and an explosive charge are contained by a plastic casing. A small booster which is placed at the rear center of the explosive makes up the last component of the charge. Initiation is accomplished by standard means such as detonating cord or a number 8 blasting cap. When Initiated, a detonation wave travels through the explosive, inverting and consolidating the steel disk into a large slug. This slug is propelled at high velocity to the hang-up, delivering more than 5 million foot-pounds of energy on impact.

Jan 1, 1981

By W. M. Dressel

Over 2 million tons of steel furnace dust containing approximately 100,000 tons of zinc and 10,000 tons of lead are produced each year. Recycling of the dusts would conserve mineral resources, lessen land area requirements for disposal, decrease pollution problems, and aid in solving our balance of payment problem. Steelmaking dusts can be pelletized and thermally treated to remove lead and zinc and to reduce the iron oxide to form metallized pellets. In laboratory tests more than 99 pct of the zinc and 85 pct of the lead was volatilized from the dust by roasting at 1,000° C in carbon monoxide. The volatilized material can be collected and treated further for lead and zinc recovery. Reduction and volatilization of over 95 pct of the zinc and most of the lead was achieved by roasting self-reducing mixtures of steel furnace dusts and high carbon steelmaking wastes in an inert atmosphere at 1,100° C. Over 80 pct of the iron in the resulting pellets was metallized.

Jan 1, 1974

Design, fabricate, and test a machine capable of operating in coal seams 48-inches and thicker that can reduce the time, expense, and injury potential inherent in extending and retracting mine-wide section belt conveyors, while eliminating the need to use additional machinery or equipment in accomplishing such moves. The Problem Many underground coal mines use a belt haulage system to move cut coal from the face to the loading area. This system usually consists of a main line belt conveyor fed by section belt conveyors. A shuttle car at the face carries the coal cut by a continuous mining machine to a feeder breaker that breaks the large lumps of coal into smaller, transport-able pieces and unloads them onto the tail piece of the section conveyor. This tail piece is skid-mounted so it can be readily moved as needed. The conveyor is kept close to the face during mining in order to shorten the haul distance of the shuttle cars. Section belts can be lengthened by adding belting, wire rope, and support hard-ware. During pillar retreat mining, these section belts are shortened to keep pace with pillar extraction operations. However, these belt moves, either the extensions or retractions, usually require six to eight workers and three to eight hours to complete. In addition, a 100-foot belt move requires workers to handle up to 4,000 lbs. of material, not including the tail section. Strain and sprain injuries can be incurred during this heavily labor-intensive task. The time required to move the section belt can also create losses in the mine's production. To help solve this problem, the Bureau of Mines

Jan 1, 1984

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

1. Introduction This document represents Part II of our final report on the development of a "Remote Sealing System for Extinguishing Coal Mine Fires. " It is a technical report which summarizes the results of system development and field demonstration. Part I of this two - part final report is an Operator's Manual for the application of the Remote Sealing System to a coal mine fire. 1.1 Background When coal mine fires go out of control and can no longer be fought directly, the standard fire fighting technique is to construct air-tight seals in the mine passages leading to the fire area so'--,that the oxygen supply to the fire is". cut off. Ultimately, it is desirable to isolate the fire zone in such a way that normal operations can resume in the remainder of the mine. The construction of seals in the- mine causes the atmosphere to pass through a toxic and explosive phase. Explosions, if they occur, are not only hazardous to the men working at the sealing operation, but can also undo much of the sealing work which has already been accomplished. Sealing of passageways surrounding the fire zone from within the mine is extremely difficult and dangerous. Methods for direct sealing are detailed in "Control of Mine Fires'. 1 An alternative to this approach is the technique of remote sealing. This involves drilling boreholes which intersect the mine passages at the locations where the desired seals are to be constructed. The seals are then constructed by pouring material down the borehole and filling a segment of the passage from bottom to top. During this operation, there are no personnel in the mine, all operations taking place on the ground surface.

Jan 1, 1973

By Thomas J. Peters

The U.S. Bureau of Mines studied the 3,500-acre Winegar Hole study area, Idaho, a legislatively proposed (101st U.s. Congress) addition to the Winegar Hole Wilderness, Wyo.; it adjoins the western boundary of the Wilderness at the Idaho-Wyoming border, about 15 m; east of Ashton, Idaho. The study was part of an Idaho Land Assessment Program to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The study area is an east-west elongated, wooded plateau south of Falls River. Although the area is covered with surficial glacial deposits, it is probably underlain by volcanic flows; light-colored and mafic flow rock were noted in sparse outcrop. No mines, prospects, mineralized areas, or mineral resources were found in the study area during a literature and field search. The only nearby prospects include geothermal and rock aggregate (volcanic cinder) sites, and several placer claims. Although the Winegar Hole study area lies within a region of potential geothermal resources, no evidence of geothermal activity was observed. Rock in the area does not split into flat slabs, which could be useful as dimension stone, and would require crushing to be used 8S aggregate. Alluvium (placer) samples contain less than SO.01 per cubic yard gold (at a $350 per oz price); alluvial deposits are too small to contain gold resources.

Jan 1, 1992

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

By Robert M. Doerr

In a process being investigated by the Bureau of Mines for recovering alumina from domestic nonbauxitic resources, calcined kaolinitic clay is leached with hydrochloric acid. Iron impurity in the clay is coleached and is removed in a solvent extraction step prior to crystallization of aluminum chloride hexahydrate, which is subsequently thermally decomposed to alumina. The FeCI3-HCl stripping liquor from the solvent extraction step is unsuitable for discharging to the environment; furthermore, economics requires recovery of the contained chloride values. In the present research, it was shown that the stripping liquor can be reacted with calcined clay to yield AlC13 in solution, plus precipitated iron oxides, residual silica, and unreacted excess clay as mixed solids. For the recovery of the AICl3 solution, the slurry could be separated or returned to the clay-HCI process stream at the solids washing step that follows primary HCI leaching of the clay. For the range 20° to 99° C, the time (t) (103 sec) required to react the waste liquor with excess clay, for essentially complete iron precipitation, depends on the absolute temperature (T) chosen, according to the expression t = e[(9.000/T) -23.5J. (1) Alumina was tried as a reagent alternative to clay but was not very effective, even under pressure and at high temperatures.

Jan 1, 1982

By Donald R. Irving

THIS CHAPTER is new to the Minerals Yearbook and will appear regularly hereafter. Its purpose is to present statistics that reflect technologic trends in the minerals and metals industries (except fuels). Much useful information has been collected annually through the Bureau of Mines mineral commodity and employment and injuries canvasses. However, these data must be supplemented by further data to permit evaluation of the type, direction, and rate of technologic change, which are vitally important in long-term mineral planning. In addition to, and fully as important as, expanding the available data is the need to ascertain that the various items collected are obtained from identical reporting units, to enable direct comparisons to be made.

Jan 1, 1960

By John Ward Smith

The Bureau of Mines derived equations expressing the theoretical relationship between density of oil-shale rock and its organic content. Effects on theoretical shale density produced by variations in mineral composition and organic matter properties were evaluated. The theoretical relationship was extended to relate oil-shale density to oil yield in both oil weight and volume units by considering the fraction of organic matter converted to oil and the specific gravity of the oil produced. Corollary equations relating organic content by volume to organic content by weight and to oil yield were developed. The general relationships apply to an oil-shale deposit uniform in character. Application of the theoretical relationships to Green River Formation oil shales was demonstrated.

Jan 1, 1969

By Bruce I. Thomas

In 1943, the Bureau of Mines investigated the occurrence of cassiterite in the gravels of Morelock Creek which flows into the Yukon River 32 miles east of the confluence of the Yukon and Tanana Rivers in central Alaska. Samples of the gravels were obtained by churn drilling test pitting, shaft sinking, and open-cut mining. The gravels along Morelock Creek are about 6 feet in depth and covered with about 2-1/2 feet of overburden. The overburden is frozen, but the underlying gravels are not. Cassiterite, with gold and other heavy minerals, is usually concentrated in the first 2 feet of' gravel above bedrock and in some places penetrates into joint planes in the bedrock. The various methods of obtaining samples are discussed, and drill logs and analyses are tabulated in this report.

Jan 1, 1948

By T. Christos

The explosive oils, nitroglycerin (NG) and ethylene glycol dinitrate (EGDN), were extracted from dynamites by a halocarbon solvent and were then determined by high-pressure liquid chromatography. Separation was achieved by liquid-liquid chromatography on a column packed with Durapak-Carbowax 400/Corasil II and the eluted NG and EGDN were detected with a double-beam ultraviolet detector.

Jan 1, 1973

As technology evolves, accidents may occur because human-system interactions were not considered adequately in the process. A systematic methodology can be used to evaluate the causes of mishaps and to develop recommendations that will enhance safety. A recent trend observed in underground coal mining is used to illustrate this principle because an underground mine is a dynamic work environment. Mining is characterized not only by frequent geologic changes but by technological evolution that can seriously degrade human performance and compromise worker health and safety The case exemplified in this paper involves implementation of remotely controlled equipment for extended cut mining. Extended cut mining technology evolved with minimal ergonomic consideration even though the change from on¬board to remote machine operation dramatically modified the role of the human component. In response to concern that system interactions should be examined more closely. a methodology was developed to identify hazards.

Jan 1, 1998

By T. Whitrnoyer, J. Sneckenberger

"The acOustic impedances of seven rat lungs were measured at frequencies between 100 and 6400 Hz. Rats were divided into two groups: a silica exposed group (N=3) and a control group (N=4). The silica exposed group was injected intratracheally with silica solution. Three of the control group were intratracheallyinjected with saline. Between four and six weeks after theinjections, all lungs were excised and degassed. Lungs were,suspended in a pressure Chamber, with the trachea canula attached to the end Of a tapered impedance tube. The lungs were subjected to transpulmonary pressures between -30 cm H2O and 6 cm H2O to simulate deflation and inflation. With transpulmonary pressure being held constant, the impedance tube was excited with random noise. A dual channel analyzer calculated H12(f), the transfer function between the two microphones. This function was used to calculate the lung's impedance at that pressure. The impedance magnitude spectra of both groups typically had peaks at 2000,3500, and 5500 Hz. Statistically significant differences. (90%confidence level or greater) between the two groups occur at the 3500 Hz peak at transpulmonary pressures of 20, 8, 6, 4, and 2 cm of H2O. This fact seems to confirm that this method can detect. lung disease. Further research will indicate whether this method will be able to detect the onset Of coal worker's pneumoconiosis.INTRODUCTIONOne of the first studies of impedance Of the human lung were conducted by DuBois et al.[2] using the forced OscillatiOn technique. This technique, however, was limited to frequencies below 30 Hz. Further studies by Van Den Berg [6] revealed thatthe lung reflected higher frequency sounds (100-10,000 Hz), instead Of behaving as an anechoic termination. This discovery has lead to several studies of the acoustical properties of both human and animal lungs at high frequencies [3,4,5]."

Jan 1, 1988

Develop an environmentally feasible method of mining shallow oil sands without removing overburden. Approach Oil sands are extracted through a single borehole by cutting into the sands around the borehole with a high pressure water jet, and pumping the resulting slurry to the surface. Although oil can be extracted from shallow fields by open-pit mining methods, this type of mining may create significant environmental impacts, including; (1) disruption of the surface, (2) accumulation of waste rock piles, (3) accumulation of tailings, (4) damage to the ground water quality, and (5) surface water pollution. The borehole mining system developed and successfully field tested by the Bureau of Mines offers a method for extracting oil from oil sand with minimal disturbance to environmental quality. (For examples of other applications of borehole mining, see Technology News Nos. 95, 63 56, and 48.) How It Works Prior to the start of mining operations, baseline conditions for ground subsidence and ground water quality are established at the test site so that the degree of subsidence and changes in ground water quality can later be determined. Oil sands mining is conducted using the Bureau of Mines borehole mining system. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three passage swivel terminated with a mining section. The mining section has an auger at the bottom. Four slurry inlet holes and an eductor are located above the auger, and a single cutting nozzle is located near the top of the mining section. The tool generates a high velocity water jet that erodes and slurrifies ores. The slurry is drawn into the inlet of the eductor which lifts the slurry to the surface where it is deposited into a slurry discharge sump. To detect evidence of subsidence, surveys of the land surface are made at regular intervals during, and until 30 days after, the termination of the mining operations. Samples of ground water from the borehole and two adjacent monitor holes are taken on alternate days during the mining operations, and are later analyzed to determine if any ground water contamination has occurred.

Jan 1, 1981

By C. J. Chindgren

The Bureau of Mines investigated the technical problems involved in recovering commercial-grade vanadium products from alkaline solutions of low vanadium content. Conditions were defined for precipitating calcium vanadates from sodium vanadate solutions with calcium chloride and calcium hydroxide and for dissolving the precipitates with acid, sodium carbonate, and sodium bicarbonate to obtain vanadium-enriched solutions from which either red cake or ammonium metavanadate was recovered. Calcium vanadates with CaO:V205 mole ratios of 2, 3, and 4 were produced with recoveries of 93 to 100 percent. Optimum recovery of the low-lime variety of calcium vanadate was obtained by employing excess calcium chloride and adjusting the pH to a range of 8.0 to 8.5. High vanadium extractions were obtained in concentrated solutions by dissolving the calcium vanadate precipitates with any of the reagents tested. The resulting extracts contained 25 to 125 grams V205 per liter. Conventional procedures used to precipitate either red cake or ammonium metavanadate from the enriched solutions gave excellent vanadium recoveries.

Jan 1, 1967

By Richard J. Mainiero, Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small-scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single-hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

Produce an annotated bibliography to serve as a comprehensive source of published information available on the use of soil amendments in coal mine reclamation and the characterization of coal mine soils. The Problem There is a substantial amount of information available tin coal mine reclamation and revegetation, particularly on the use of soil amendments to ameliorate site conditions and aid vegetation establishment, growth development, and productivity. Additionally, site characterizations based on chemical, physical, and mineralogical properties have been thoroughly researched. This information, however, is widely disseminated throughout various professional and scientific journals, State and Federal documents, proceedings of conferences, theses, and other technical writings. A critical need exists for a comprehensive and up-to-date summary of published information concerning the uses, methodologies, and types of soil amendments that arc necessary for reclamation success.

Jan 1, 1991