Search Documents

By S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

By Terry J. Close

In 1992, as part of the U.S. Bureau of Mines Idaho Land Assessment Program, the Western Field Operations Center investigated the mineral resources of the 30,300-hectare Elk Summit study area. The area is in the Clearwater National Forest, adjoining the Selway-Bitterroot Wilderness in Idaho County. Idaho. The study area is underlain by granitic and metasedimentary rocks. Associated with these rocks are road metal (stone) resources, black sand mineral placer resources, and thermal water resources. Also present are abundant sand and gravel. Two of the five sites examined during the Bureau study have road metal (stone) resources, one has black sand mineral resources, one has thermal water resources. The fifth site is a black sand mineral placer occurrence. There is no evidence of petroleum or coal resources. Idaho County records indicate that 38 mining claims, mostly black-sand placer, have been located in the study area, Twenty-three of the claims are current. Workings consist of a few pits and trenches at the placer, and two borrow pits. The only mineral commodity produced from the area was about 1,500 tonnes of stone excavated from the Savage Pass and Swamp Creek borrow pits along the Elk Summit road, north of Hoodoo Lake. The stone was used to surface the road; these stone resources will continue to be used as needed.

Jan 1, 1993

By d&apos, Kathleen J. Amico

This summary appears in Minerals Year-book volumes I-II, and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The sections of this chapter and the area chapters in volume III contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1967

Reduce costs of surface mine reclamation by improving scaper operating efficiency and reducing tire costs. Approach The Wheel Slip Monitor senses and compares the peripheral speed of a scraper's four tires 10 the true ground speed of the scraper, and alerts the operator if any of the tires exceeds a predetermined amount of slip. This system helps scraper operators reduce wheel slip during the loading cycle, thereby improving the loading efficiency of the scaper and reducing tire wear and damage. How It Works The system consists of five ultrasonic doppler velocity-sensing devices for measuring the speed of each wheel as well as the true ground velocity (see photograph). Each sensor produces an electrical output signal having a frequency proportional to the speed of the tire or terrain. The signals are conveyed through electrical cables to a control box in the operator's cab where they are converted to voltages proportional to individual wheel speeds (see photograph). The signals are further processed to activate a blinking red light, corresponding to any individual wheel which is slipping, and to sound a beeping tone that is audible to the scraper operator. The rate at which the light blinks and the tone beeps is proportional to the degree of slip. Alerted, the operator can take corrective action.

Jan 1, 1985

By M. J. Ferrante

Relative enthalpies of cuprous iodide (CuI) were measured at the Bureau of Mines to provide thermodynamic data for the advancement of min-eral technology. Enthalpy measurements between 298.15 and 1,396.3 K were made with a copper-block drop calorimeter. The temperatures of transition were measured by differential scanning calorimetry (DSC). Reversible transitions were determined at 643 K with a standard enthalpy of transition [(6Htr)] = 0.74 kca1/mol, at 679 K with a [6Htr = 0.65 kca1/mo1, and at 868 K] with a standard enthalpy of fusion [(6H~) = 1.895 kca1/mol.] Tabulated values are listed at selected temperature increments from 298.15 to 1,600 K for the standard relative enthalpy (HO -H298), heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)!T]. The enthalpy data are also given in the form of equations and combined with thermodynamic data from other investigations to derive values of standard entha1pies of formation [(~HfO)], Gibbs energies of formation [(6GfO)], and logarithms of the equilibrium constants of formation (log Kf).

Jan 1, 1987

By Van E. Shaw

Fusion of an 86-percent euxenite concentrate with ammonium sulfate was investigated by the Bureau of Mines. Reaction for 4 hours at 400° C results in conversion of both the rare-earth elements and the titanium-columbium components to water-soluble compounds. Similar results are obtained with ammonium bisulfate. Stirring the fusion mass decreases the reaction time substantially. Alternatively, treating the fusion product with a 3-hour, 650° C calcining step renders the non-rare-earth constituents insoluble, thereby allowing selective leaching of a pure rare-earth fraction with an overall yield of 97 percent.

Jan 1, 1967

By Edward W. Parsons

The explosive-expansion center-hole anchor was designed and developed for the specific purpose of use as a component of an instrument system that measures differential ground movement within a small drill hole in rock. Such anchors should have an unobstructed center hole, should be installed without a twisting action which could tangle connecting wires, and should be capable of being installed at depths in excess of 100 feet. The anchor has a thick-walled center tube and a thin-walled outer tube. Low-energy detonating cord, wrapped around the center tube and detonated with a mild end primer, expands the outer tube to produce anchorage. The explosive-expansion center-hole anchor can be installed easily in drill holes of any inclination but cannot be installed under water. Centering of the anchor is critical with regard to its subsequent holding power. The anchor is safe to make and handle.

Jan 1, 1965

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U .S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed ?mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1965

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract I for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 11, 1976

By Fred N. Kissell

Methane flows and pressures were measured in mines in the Pittsburgh, Hartshorne, and Pocahontas No. 3 coalbeds. From the data, the permeability of each of these coalbeds was computed. It was found to depend strongly on the type of coal and on the amount of water in the coalbed, and it was found to increase with time. All of the coalbeds had a high-permeability zone adjacent to the face or rib, and the Pittsburgh bed exhibited directional anisotropy. Surprisingly, little or no overburden effect was observed.

Jan 1, 1972

By D. G. Kesterke

Research was conducted to determine the feasibility of extracting elemental oxygen from silicate-bearing melts by high-temperature electrolysis. The method was based on a modification of existing processes for electrowinning metals from their oxides dissolved in molten halide systems. Electrolyses were performed at temperatures ranging from 1,050° to 1,250° C in boron nitride cells that incorporated a silicon carbide cathode and an iridium anode. The electrolytes contained volcanic scoria as the oxygen source, plus mixtures of BaF2 and LiF as fluxing agents. Cell gases containing almost 14 volume-percent oxygen were obtained. The average anode current efficiency for several experiments of extended duration was calculated to be 55 percent. Cell design and operating conditions are described, and some of the problems associated with the process are discussed.

Jan 1, 1971

Design a high-production coal mining machine with inherent low dust generation and low frictional ignition potential. Approach Constant depth linear cutting (CDLC) provides a longterm solution to excessive dust generation from shearers and continuous mining machines through new design of the rotary drum culling system. Problems with rotary drum systems, which must be eliminated to control the dust generation at the source, include the effect of a con¬stantly varying depth of cut using fixed bit spacing, secondary fragmentation of already broken coal and, frictional heating of bits and entrainment of dust by fanning action due to high drum rotational speed, Each bit on a rotary drum enters the coal face at zero depth of cut, goes to some maximum depth at the horizontal centerline during sump, and exits at zero depth.

Jan 1, 1989

By d&apos, Kathleen J. Amico

THIS SUMMARY is shown in volumes I and III of this series on mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and exported from the United States. For further details on production, see the several commodity and area chapters. A summary table comparing world and U.S. mineral production also is included. [ ]

Jan 1, 1960

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

Provide respiratory protection and a clean work environment for stationary or semimobile workers at minerals processing plants. Approach An Overhead Air Supply Island (OASIS) was developed which filters, conditions, and evenly disperses an envelope of clean air over a worker's head, thereby insuring reduced dust levels and a clean work environment. How It Works The concept for the OASIS derives from an earlier Bureau development of a canopy air curtain for continuous mining machines (see Technology News #21). In this application, the benefits of a reliable, self-contained, self-cleaning industrial-duty air filtration and distribution system are extended to the minerals processing field. The OASIS draws dust-laden room air into a filtration system, removing the dust and delivering clean air to a specific 16-square-foot area. It consists of: ? a self-cleaning primary filter ? a heater (cooling coil optional) ? an airflow distributor and secondary filter (combined)

Jan 1, 1985

Improve the reliability and accuracy of subsurface images using constrained tomography with enhanced ray-tracing capabilities. Background Geophysical tomography is a technique for imaging the structure of a rock mass using seismic or radio waves, in the same way that medical CAT scans image human tissue using X-rays. Tomography has found numerous practical applications related to mining, including lithologic and structural characterization, fracture detection and fluid monitoring, void detection, and evaluation of stress state and integrity of mine structures. Problems Two fundamental problems have largely prevented geophysical tomography from enjoying the tremendous success achieved by medical tomography. The first is a consequence of practical limitations on the placement of sources and receivers of wave energy: ideal resolution can be attained only when the region being imaged is entirely surrounded by sources and receivers, so that it is crossed by rays traveling in all possible directions. When such coverage is impossible or impractical, the inversion becomes underdetermined: there id not enough information in the measured data to provide a mathematically unique solution. The second major problem in geophysical tomography is the necessity for detailed ray tracing. Commercial software, as well as previous U.S. Bureau of Mines (USBM) software, employs a ray-shooting algorithm that may be unable to model some ray paths when velocity contrasts are larger than about 100%. These ?shadow zones" result in loss of data and degradation of reconstructed images.

Jan 1, 1994

Identity the difficulties of establishing vegetation on mining-related wastes resulting from adverse chemical, physical, and biological properties; describe the ecological and soil factors affecting the relationship between mycorrhizal fungi (soil microorganisms) and plants; and evaluate the feasibility of establishing vegetation on mine waste by introducing mycorrhizae. Problems in Revegetation Successfully using vegetation to stabilize a situ disturbed by mining-related activities depends on knowing the chemical, physical, and biological characteristics of the site prior to, or at the time of, stabilization. The primary objectives of mine land reclamation are to minimize environmental degradation and to facilitate the re-establishment of a functional plant-soil system. Mining disturbances can significantly alter the physical, chem¬ical, and biological characteristic of a site, thus affecting plant establishment, survival, and growth. The physical disturbance caused by the removal and replacement of soil and overburden, together with the waste material from ore processing, affect the chemical, physical, and biological process within the disturbed soil or waste. Additionally, variability in soil properties results from differences in climate, topography, vegetation, and parent material of the site.

Jan 1, 1993

By Suresh K. Bhatt, Dennis R. Dolinar

The roof bolt system of a mine, if properly selected and installed, can allow for better roof control and reduce the potential for roof falls. Because of this potential to reduce roof falls and improve ground control conditions, the National Institute for Occupational Safety and Health (NIOSH) has an interest in the types of roof bolts that are used by the coal industry. Further, NIOSH has conducted research into how various support parameters can affect the number of roof falls that occur, including support type. Today, the five main types of roof bolts installed in U.S. coal mines are mechanical anchor bolts, point-anchor or resin-assisted mechanical anchor bolts, torque-tension bolts, combination bolts, and fully grouted resin rebar. This paper describes each support in detail. Because of the importance of resin in the functioning of the majority of bolts installed, resin grouts are also discussed. Further, trends in the types of roof bolts used are reviewed. Over the last 10 years, the significant trend has been the large reduction in the relative number of mechanical anchor bolts that are installed. These bolts have been replaced mainly by the resin-grouted rebar system. Data are also presented to show the impact of these changes in bolting on the number of roof falls.

Jan 10, 2000

By Arthur S. Swanson

The DuBois fluorite property in the southwestern part of Hardin County, Ill., has been active intermittently since 1904 and has produced an estimated total of 1,000 to 2,000 tons. The persistence of the vein and the stratigraphy suggested extensions of the ore body formerly mined. The Bureau of Mines investigated the property by core drilling early in 1944. Four holes were bored which totaled 1,106 feet and extended along a strike length of 1,150 feet. The data obtained in the course of the investigation are presented in this report.

Jan 1, 1948

By Noel N. Moebs

The Bureau of Mines measured surface subsidence above four small coal mine room-and-pillar sections in southwestern Pennsylvania, to obtain preliminary information on the magnitude and character of selected parameters, such as angle of draw and maximum subsidence, which are essential to the development of subsidence prediction methods. Data varied widely at the four sites; this is attributed to local geologic and mining conditions. Surface deformation at each site was of a magnitude normally associated with severe structural damage.

Jan 1, 1982