Search Documents

By Sarkis G. Ampian

The Bureau of Mines has developed a method for identifying fine particles of beryl in mineral samples by preferentially staining the beryl grains. The sample is first subjected to a heated sodium hydroxide solution to etch the beryl particles, which are subsequently stained an intense blue color in a boiling alkaline solution of quinalizarin. Positive identification of beryl grains permits quantitative analyses by microscopic techniques. INTRODUCTION Beryl, a beryllium aluminum Silicate, is the principal ore mineral of beryllium. The only known commercial concentrations of this mineral are found in pegmatite dikes of granitic composition. Normally beryl is associated with muscovite mica, quartz, and the sodium-and potassium-bearing feldspars (orthoclase, microcline, and albite). Other beryllium-bearing minerals which are found occasionally in minor amounts with beryl are phenacite, a beryllium silicate, and chrysoberyl, a beryllium aluminate.

Jan 1, 1962

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the comparative effectiveness of three wet dust control techniques for face drilling. Previous attempts to achieve effective dust control on face drills with dry collectors have not met with success, the largest problem being sustained effective dust capture at the face. Results show that (1) foam-through-the-drill can provide 95-pct average total dust reduction in gypsum; (2) water mist-through-the-drill can provide approximately 91-pct average total dust reduction and 93-pet average respirable dust reduction in salt; (3) external boom-mounted water sprays can provide approximately 50-pet average dust reduction for both total and respirable dust in salt. The investigation showed that (1) foam and water in small quantities are very effective dust control techniques for face drills when applied through the drill steel at the point of dust generation, and (2) boom-mounted water sprays are only minimally effective for dust control on face drills.

Jan 1, 1981

By P. W. Jerant

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By Ruth F. Brinkley

This circular summarizes the research and technologic activities and publications of the Federal Bureau of Mines Division of Explosives Technology4/ during fiscal year 1959 (July I) 1958-June 30, 1959). Part I briefly describes the programs that were active during the report period and presents a summary of some of the information not published elsewhere. In many instances the results are only preliminary and are subject to revision on the basis of continuing investigations. Detailed reports of all programs not security classified will be made later. Part II lists and describes briefly the publications of the Division during fiscal year 1959. If the published material has some bearing on activities still current during the report period, this is indicated by references in Part I.

Jan 1, 1961

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 11,069-acres of the 12,290-acre Eldorado Wilderness Study Area (NV-050-423) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, adjacent to and northeast of the town of Nelson. There are inferred subeconomic resources on the Paul (gold, silver), Bel (gold, silver), Big Horn-Inez (silver, copper, lead, zinc) claims, and Montezuma (gold, silver, copper, lead, zinc) patented claim group in the Eldorado study area. Because of lack of exposures, tonnage and grade on these properties could not be determined. No resources were identified for the other five properties examined in the area. The southern two-thirds of the area is in the Eldorado mining district, a base- and precious-metal district which has been intensely explored for over 100 years. Nine claim groups were examined in the study area. Eight claim groups are within the Eldorado district and include the Montezuma (patented -M.S. 3966), Bel, Eldorado, VAR, SINJUN, Paul, Rusty Bit, and Big Horn-Inez. One property, the Flintstone claim group, is north of the Eldorado mining district at the north end of the study area.

Jan 1, 1988

By R. Van A. Mills

[In previous contributions** the writer has called attention to important relations that faulting bears to the migration and accumulation of oil end gas. It has been pointed that favorably situated parts of oil and gas bearing, sands have been enriched by migration art segregation incident to faulting. The escape of water through natural passages such. as fault fissures has induced wide spread hydraulic currents through the beds toward these, points, of diminished pressure and these water currents, plus buoyancy hove contributed largely toward the migration of oil to favorable rock entrapments in the vicinity of the faults.*** The propulsive force of expanding gas has been one of the contributing causes for the hydraulic currents. Paradoxical as it may seem, the escape of gas with entrained oil through fissures has been on important factor In the migration, and accumulation of oil in many faulted areas. Compressed gas is the propulsive force by which oil generally moves to producing wells. It is also one of the propulsive forces by which oil has moved with or even ahead of water under conditions: of differential pressure brought about by faulting.]

Jan 1, 1922

By Floyd G. Anderson

Bureau of Mines studies show than an electronic counter can be used for determining just concentrations from midget impinger samples collected in bituminous coal mines. A sample correlation coefficient of 0.91 for data obtained using the electronic counter and the Bureau of Mines microprojector procedures indicates a significant linear relationship between the methods. The electronic counter provides better counting precision and reduces analytical time.

Jan 1, 1968

By Charles L. Kimbell

Available statistics on 1991 worldwide consumption of selected non fuel mineral commodities shown in table 12 indicate downturns for all but 3 of the 15 listed commodities. It should be stressed that in most instances, the consumption declines were primarily the result of lower levels of use in the former U.S.S.R. and the former centrally planned economy nations of Eastern Europe. However, several commodities suffered use cutbacks in market economy countries. In the case of the nonferrous metals covered In the table, the differences in performance between market economy countries and the former centrally planned economy states are immediately evident from the table itself. Among these important commodities, refined lead, primary magnesium, and refined tin registered downturns for market economy countries as well as among the centrally planned economy countries. Also notably, cadmium use showed no significant change from 1990 levels in either group of countries. Global consumption of iron ore fell by 3.4 % or about 31 million tons, and this was a greater decline than that logged for production of marketable iron ore and related products, which was down by only 3.0% or almost 28.2 million tons. Thus, it would seem that for another year there was a net addition to stocks. The 1991 drop in iron and steel scrap use was about 5.5 % or about 18 million tons, on the percentage basis somewhat greater than the 4.8% or 36.9 million ton drop in global steel production. Although consumption of iron ore and iron and steel scrap are not broken down by region in table 12, it seems almost assured that the pattern of 1990 continued into 1991: drops in use in the former U.S.S.R. and Eastern Europe were the overwhelmingly dominant declines and accounted for much, although not all, of the global decline, whereas among market economy countries as a group, there were upturns for both materials. On a global basis, it would appear that the slight shift in the ratio of pig iron to scrap in steel furnace charges noted in 1990 continued into 1991, this shift being toward a slightly larger proportion of pig iron with a corresponding decline in the share accounted for by scrap.

Jan 1, 1993

By W. E. Miller, Kennedy. R. E., G. W. Jones

"INTRODUCTION Ethyl mercaptan (CH3,CH2SH), a combustible organic liquid of the thioalcohol type, is employed at an odorant in many types of fuel gases and dangerous atmospheres, which in themselves are devoid of characteristic odors, to give warring against leakage of such gases or atmospheres into places where they might constitute health or explosion hazards.Ethyl mercaptan has a penetrating disagreeable odor resembling that of onions, garlic, hydrogen sulfide, or rotting cabbage, that exceedingly low concentrations of it can be detected. The of odorants as a beans of detecting leakage of gases and atmospheres has been investigated extensively by chemists and engineers of the Bureau of Mines, and numerous reports as to its value have been published."

Jun 1, 1942

By I. L. Nichols

Laboratory characterization studies have investigated the processing variability of carbonaceous uranium-bearing materials found in-sandstone deposits. This work was conducted by the Federal Bureau of Mines in support of its goal to maintain an adequate supply of minerals to meet national economic and strategic needs. Conventional processing produces only partial uranium recovery from these ore materials. Ore samples from New Mexico, Texas, and Wyoming were examined, and each responded differently. Using direct acid leaching techniques, some of the ores required acid additions of only 50 pounds per ton, while others required 300 pounds per ton of material. Maximum extractions ranged from 83 to 94 percent in the six ores tested. Roasting those ores prior to leaching improved extraction of the uranium to the 90 to 99 percent range. An oxidative autoclave treatment used with five of these ores resulted in extraction of 78 to 97 percent of the uranium. The experimental studies also showed that some carbonaceous materials can be concentrated by froth flotation. The flotation tailings were amenable to acid leaching, and up to 98 percent of the uranium was extracted from this type of material.

Jan 1, 1979

By A. W. Fahrenwald, W. W. Staley

"In flotation concentration, various machines are employed for agitation and aeration of the ore pulp in the operation of frothing. The power required in the operation of these machines varies considerably with the type and make of machine used. The object of this investigation was to determine the effect of certain physical properties of the pulp particularly viscosity, density, and temperature - upon the power required by certain forms of pulp agitators.The viscosity factor is most involved because it is affected by temperature and by density. Viscosity of liquids and suspensions has been extensively studied and the physics and mathematics of the subject are much enlarged upon in books and in the literature. It is not, however, the intention of this study to become involved in the intricacies of these phases of the subject.The agitation of the various mediums in the experimental work did not last long enough to cause a measurable rise in temperature from the ""beating"" of the medium, hence no cognizance is taken of this factor.No attempt has been made to correlate the data obtained with the impeller with any information regarding centrifugal pumps. The object sought here is quite foreign to the problems of pumping. The impellers used are ""open"" and air is involved.The experiments performed and the data obtained are presented. Only that amount of discussion necessary to make the results understandable is given.Tap water was used in all experiments. A comparison of distilled water and tap water showed no measurable difference. In the experiment in which sodium chloride was needed, the commercial salt as used in fire assaying was taken. The quartz was of the ""bull quartz"" variety, thoroughly washed free of iron oxide."

Jun 1, 1930

By M. J. Kovalik

Illinois No.6, a high-volatile B coal of low fluidity, was blended with fluidized-bed char and coke breeze to improve the strength of the coke obtained from carbonizing this coal. Twenty-one tests, selected from those made in the small-scale Hanson carbonizer, were carbonized in the BM-AGA 13-inch-diameter, cylindrical retort, with a coal charge of about 90 pounds; the strength of the cokes was determined by the standard ASTM tumbler test. Using the same procedure, 10 tests were made with High Splint, a high-volatile A coal from Harlan County, Ky. Carbonization of the blends produced larger and stronger cokes than did the Illinois No.6 coal singly. The optimum blend contained 6 percent each of char and coke breeze. Further improvement in coke strength was realized by either preheating this blend prior to carbonization or by adding a small pro-portion of a premium blending coal. The former method could possibly eliminate the use of premium coking coals in blends with Illinois No. 6 coal to make an acceptable metallurgical coke. Except for no improvement in coke strength by preheating, results for High Splint coal showed behavior similar to that of the Illinois No.6 coal.

Jan 1, 1973

Develop a method for recovering phosphate from a wide variety of complex western phosphate materials, including low-grade ores, tailings, and unused fines. Approach A flotation technique is used for this broad type of extraction. The method includes depression of phosphate minerals and anionic flotation of carbonate minerals, followed by cationic flotation of silicate minerals. How It Works A slurry is prepared for flotation by sizing to remove a low-grade, high-impurity slime fraction. Depending on the material, further sizing and/or grinding steps may be used to produce a size concentrate or to remove gangue. The flotation feed is conditioned with H2SiF6 and a fatty acid emulsion. The H2SiF6 is absorbed chemically to the phosphate mineral surface, making it strongly attracted to water and preventing adsorption of the fatty acid. Under these conditions, the fatty acid is a selective collector for carbonate minerals, which are removed as a froth product. Next, the silicates are floated with an amine reagent added directly to the slurry without additional pulp preparation.

Jan 1, 1982

By G. H. Hopkins

Like most industries, the refining industry has in recent years been confronted with the problem of a decreased martin of profit, due both to a general lowering of prices and to rising costs. This has resulted in accelerating a program of increased efficiency an evidenced by improved methods and the installation of equipment designed to affect a number of economies hitherto regarded as unimportant. Perhaps the most important of these has been that of fuel economy for, as is not often realized, a refinery consumes about one-tenth as much fuel as it produces. A recently completed canvas., made by the Bureau of Mines for the purpose of determining the trend of fuel consumption at refineries in the United States, showed the following outstanding points, (1) a decrease in the use of oil for fuel in 1926 of approximately 4,000,000 barrels as compared with 1925; (2) a small decrease in the use of coal; (3) a material increase in the use of gas, both natural gas and refinery gas; and (4) a considerable increase in the use of petroleum coke.

Jan 1, 1927

By B. Dimitriades

The Bureau of Mines measured the reactivities of 19 hydrocarbons known to be prominently present in automotive exhaust and ambient air in a smog chamber. Results agreed well with those obtained using two other smog chambers. Reactivity scales were developed for hydrocarbons and aldehydes using the results of this work and those of a previous study. Application of the reactivity scales to automotive exhaust samples gave fair agreement between predicted and observed rate-of-N02-formation values; however, predicted and observed ozone yields were neither in agreement nor did they correlate well. This lack of correlation for ozone yield was attributed to the inappropriateness of (1) the individual component reactivity data, (2) the reactivity classification scheme used, and (3) the linear summation method. In seeking to understand this problem and to develop more appropriate reactivity scales, the data were examined from a reaction mechanism standpoint, and further studies were suggested.

Jan 1, 1975

By L. D. Tracy

The first study of this subject hits been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal-mining industry to standardize the forms of leases, and so avoid some of the abstruse and ambiguous clauses which slay be found in many of them and the consequent liability of costly litigation. In some of the publications of the Illinois Mining; Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the 'State have been divided into eight geological districts, each district being treated separately. This report covers District No. VI of that classification, and it is hopped that studies of the other districts will be completed in the near future and similar results published.

Jan 1, 1926

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals4/ and. investigations of their chemical and physical properties.5/ The coal represented by the sample from weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

By B. G. White

NIOSH researchers have identified a pattern of fracture zone development that suggests an explanation for fracture formation around rectangular openings in underground mines. This pattern is characterized by shearing and dilation that result in either faults or in the repeated formation and propagation of en echelon fractures from sites of tension. Two computer modeling codes, Fast Lagrangian Analysis of Continua (FLAC) and Particle Flow Code (PFC), were used to model different aspects of this pattern. Use of very small elements with FLAC enabled the identification of sites of initial tension near the skin of square-cornered rectangular openings, while PFC allowed the initiation and progressive development of fractures from these sites to be followed as the fractures evolved. Such studies can lead to a greater understanding of how roof support can be better selected and installed for specific conditions in underground mines prone to roof falls and rock bursts. These studies may also lead to modifications of corner and opening shapes that could be incorporated into mine designs to produce more stable mine openings and reduce the risks of rock falls and rock bursts.

By R. L. Anderson

Mechanical cleaning of bituminous coal in the United States was begun about 1875, with plants in western Pennsylvania and Illinois. The United States Geological Survey began to record the quantity of washed bituminous coal in 1906; and the series was carried forward to 1923, except that no data were collected, for 1922. This statistical work was transferred to the Bureau of Mines in 1925, and the collection of data on mechanical cleaning was resumed in 1927. Data collected before 1927 include only the coal that was washed at the mines and do not include that cleaned by pneumatic methods at the mines and that cleaned at central washeries operated by consumers.2/ The total bituminous coal washed in 1906 was less than 10 million net tons. In 1927, the first year for which complete figures are available for all types of mechanical cleaning, 28 million net tons of bituminous coal were cleaned in the United States.

Jan 1, 1951

Develop improved blasting practices that can help to curb overbreak in highwalls at surface mines, thereby reducing the hazards of rock-falls to workers and equipment, The Problem The serious hazard in surface mining is the falling of rock from highwalls. Poor highwall stability is caused in part by geologic conditions, but often is aggravated by faulty blasting practices, where the explosive energy not only fractures the rock to be excavated, but also damages the rock that borders the excavation. This reduces the general stability of the hlghwall and increases the rockfall potential. The probability of injury to mine workers or damage to equipment associated with exposure to the highwall increases with the height of the highwall and the extent of its overbreakage. Most rockfalls occur in the first 15 days after a new highwall is exposed. This statistic is significant since most of the work below a highwall is done during this period. The area of greatest hazard is within 25 ft of the toe for rocks that fall vertically, and up to 90 ft from the toe for falling rocks that are deflected by the highwall during their descent, The workers most frequently involved in such accidents are dozer operators, ground laborers, and shovel operators or oilers.

Jan 1, 1985