Search Documents

By John Owens, Marc Endicott, Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (1) study the interaction between MRS’s and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS’s have capacities of 5,340 and 7,120 kN (600 and800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS’s help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-seam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4)geologic structures, and (5) panel layout designs and mining practice.Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts are needed.

By Eugene T. Sheridan

The 23d annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, revealed that 75 producers in 17 States re-ported commercial production of peat in 1956. Forty-seven producers reported humus production, 19 reported reed-sedge peat, 17 reported moss peat, and 1 reported muck. This total exceeds the number of active operations, but several producers reported recovering more than one type of peat. Fifty-five percent of the total production was reported as peat humus, 30 percent as reed-sedge peat, and 15 percent as moss peat. A negligible amount was reported as other types. More than one-fourth of the total output was raw peat with no preparation, other than having been air-dried. The remainder consisted of processed peat prepared for use by cultivation, shredding, or kiln drying.

Jan 1, 1958

By John B. Umhau

In 1930 , 65,448 long tons of virgin or primary tin were consumed by 1,292 establishments in the United States , representing about 91 per cent of the total consumption as computed from imports , exports , and stocks at the beginning and the end of the year . The reported consumption was equivalent to 38 per cent of the world's tin production in 1930 , estimated at 171,000 tons , and was 12 per cent less than the 74,369 tons consumed by 1,307 establishments in 1928 . Decreased consumption of new tin in 1930 ás compared to 1928 was a reflection of the general industrial depression . All of the tin- consuming industries showed substantial decreases except tin plate and terneplate , white metal , and tinning , which showed small tonnage increases aggregating only 1,200 tons . The largest tonnage decrease was in the use of new tin in babbitt which declined 33 per cent in 1930 as compared to 1928. This was largely attributable to the decreased production of automobiles and trucks , which was 24 per cent lower in 1930 than in 1928. Percentage decreases in other important tin- consuming industries were as follows : Solder 18 per cent , bronze 19 per cent , tin foil 40 per cent , chemicals 23 per cent , tin oxide 44 per cent , and type metal 46 per cent . The distribution of the amount consumed by various uses during 1927 , 1928 , and 1930 is shown in table 1 . Consumption studies indicate the fact that variation in tin consumption from year to year parallels the fluctuations in demand for the already wellestablished tin products . For example , the manufacture of motor cars and trucks3 required only 11,000 tons of tin in 1930 compared to 19,000 tons in 1928 ; the canning industry continues to require the greater portion of the tin plate and much of the solder . Recently developed industries , while affecting total consumption of bearing metals , solders , etc. , to some extent , have made little change in the relative importance of these commodities as consumers of tin .

Jan 1, 1932

By G. Nuñez, M. A. Pathak, A. A. Afshari, C. F. Stanley

"To help evaluate the vibration patterns of an excised lung, a method is developed to determine which parts of the surface of an excised lung are responding to acoustic excitation via the trachea. Holographic interferometry, a very' sensitive technique ·that can measure movements of a few microns, is used to detect the lung surface movements.The intact lung and heart are excised from Long· Evans male rats weighing 250 gm. A tube is inserted into the trachea and connected via a funnel to a 3 inch cone speaker. The assembly is positioned in the holographic unit and excited at frequencies up to 10,000 Hz. The holographic unit contains an acousto-optic shutter used with a 0.5 watt Argon laser.The resulting reconstructed holograms contain interference fringes that are indicated of lung surface vibration.INTRODUCTIONA 1986 report by the U.S. National Committee on Biomechanics [1] describes diseases of the lung as a major national health problem. One of the recommendations of the report is for continued study of the mechanical properties of lung tissue. As an example, the report cites at least three areas that would benefit from a better understanding of the vibratory patterns or the lung."

Jan 1, 1989

By J. P. Rider

Average production from longwall mining operations in the United States has risen from approximately 800 tons per shift in 1980 to over 4,600 metric tons per shift in 1999. Such a large increase in production has the potential to generate significantly more dust. Previous NIOSH research has shown that, on average, respirable dust levels generated by the shearer accounts for 50% of the airborne dust generated during longwall mining. Ventilating air and water are primary controls being used in an effort to reduce longwall dust levels. Longwall operators are applying more air and water than ever before and have expressed concern over reaching maximum practical limits for these controls. Full-scale laboratory tests are being conducted to evaluate the impact on shearer-generated dust levels for changes in face air velocity, water quantity at the shearer, water spray pressure, spray system design, mining height and cutting direction. Results of this research should identify the most appropriate control levels for various operating conditions. In addition, general recommended dust control practices for longwall mining will be discussed. KEYWORDS Longwall, coal dust

Apr 1, 1975

By J. J. Rutledge, C. A. Herbert

In 1916 the Bureau of Mines, the Illinois Geological Survey, and the University of Illinois, working under a cooperative agreement, began an investigation of the subsidence of the surface above coal- mining operations. Four widely separated places where mining was in progress were selected as observation stations-one in the northern Illinois longwall coal field, one in the central Illinois coal field where the room-and- pillar panel system of mining was being used, and two in the thick coal of southern Illinois where the room-and-pillar panel system of mining was employed. These four points of mining activity gave a rather wide opportunity for observing subsidence when different mining methods were used. The four places selected for investigation of surface subsidence due to coal mining have been designated as follows: 1. A, in the northern Illinois longwall coal field, where the coal company has been operating coal mines for 30 years and where long- wall advancing is the only method of mining. 2. B, in Perry County, where panel room-and-pillar mining of a thick seam of coal is in progress and where mining operations have been carried on about 40 years. 3. C, in Macoupin County, where the coal company has been min- ing coal by the panel room-and-pillar method for about 15 years. 4. D, in Franklin County, where the coal company has been mining coal for 10 years by the panel room-and-pillar method.

Jan 1, 1927

By Lloyd A. Morley, Alan M. Christman

This report was prepared by the Department of Mineral Engineering, The Pennsylvania State University, University Park, Pennsylvania under USBM Grant Number G0155102. The grant was initiated under the Metal and Nonmetal Health and Safety Research Program. It was administered under the technical direction of the Pittsburgh Mining and Safety Research Center with Mr. Roger L. King acting as the Technical Project Officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this grant during the period February 1, 1975 to July 31, 1976. This report was submitted by the authors on August 31, 1976.

Jan 1, 1976

Determine the site specific flow behavior of leachants and groundwater during development, production, and restoration phases of an in situ leaching operation. Approach A computer program has been developed which simulates the hydrologic activity associated with in situ mining. Various user options enable modeling of many of the site specific geologic conditions and well field specifications that affect the hydrology of solution mining. How It Works In situ hydrology is modeled, using a closed-form solution to the three-dimensional, partial differential equation that describes changes in hydraulic head as a result of pumping from leachant Injection and recovery wells. Model capabilities include arbitrary well patterns and pumping schedules, partially penetrating well screens, directionally anisotropic permeability and natural groundwater flow, in either

Jan 1, 1981

By Dennis Dolinar, Christopher Mark, Gregory M. Molinda

In 1999, 2,087 unplanned roof falls were reported from 841 mines. Nearly 55% of all mines reported at least one roof fall, and nearly 17% of the mines reported five or more falls. In order to investigate the variables that contribute to roof falls, the National Institute for Occupational Safety and Health (NIOSH) compiled a national database of roof performance from 37 coal mines. Geotechnical factors and their effect on roof fall rates were compiled from over 1,500 miles of drivage. The factor that is the best predictor of roof fall rate is the Coal Mine Roof Rating (CMRR). For a low CMRR (#30), almost all cases have high roof fall rates. Conversely, high roof fall rates are rare for strong roof rocks (CMRR $ 60). Roof fall rates were also higher in deeper mines, probably because of greater stresses. Intersections were much more likely to fall than roadways, and four-way intersections were more prone to fall than three-way intersections. In a controlled comparison of the effect of increasing bolt length on roof fall rates, it was found that longer bolts reduced the roof fall rates in 11 of 13 cases. A relationship between the roof fall rate, the intersection span, and the CMRR was also found. Finally, a systematic method for tracking roof performance and geotechnical variables was demonstrated.

Jan 10, 2000

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By G. Dale Cor, Will H. Coghill, M. F. Williams, I. L. Feld

"INTRODUCTION During the past several years the Southern Experiment Station of the Bureau of Mines, with the cooperation of the University of Alabama, has given attention to hydraulic classification. One of the things this work has revealed is a variability not generally recognized in the conditions of teeter at different depths. This report depicts the passage of material through a teeter column and its emergence as a classified product.The work was made possible through the development of a classifier for several hundred pounds per hour permitting a small quantity of coarse spigot material to be discharged without the usual interruptions caused by stop-pages. Previous designs of small classifiers have been unsatisfactory because the,orifice used to control the quantity of spigot product as subjectto stoppages, particularly when attempting to discharge a small quantity of although the classifier used in this work has been described in detail in a previous publication 6/ its principal features will be discussed briefly herein. The main subject matter of the paper is based upon the three figures that illustrate in panorama the conditions that exist in a classifier during the continuous classification of bituminous coal, anthracite coal, and an iron ore trailing."

Jan 1, 1946

By A. G. Kim

Coal formation begins in peat swamps or bogs, in which microorganisms alter plant material and initiate the formation of carbonaceous sediments. Methane, which constitutes about 98 percent of the hydrocarbon gas in coalbeds, is known to be a product of anaerobic microbial metabolism. To determine if other hydrocarbon gases could be produced in an environment similar to that of a swamp, samples of wood cellulose and lignin were inoculated with soil micro-organisms and incubated anaerobically. The resultant gases included methane, ethylene, propane, propylene, butanes, pentanes, and carbon dioxide. Hydrogen was also produced from the wood samples during the first month of incubation. Over 90 percent of the produced gas was methane; C02 was the other predominant component. Concentrations of all other hydrocarbon gases ranged from l to 20 parts per million, approximately 0.1 percent of the total hydrocarbons, which was less than the concentration in coalbeds. Therefore, although higher hydrocarbons could be produced in a swamp environment, subsequent mechanisms, either concentration by adsorption or formation during geochemical reactions, must affect the final concentration of higher hydrocarbons in coalbeds.

Jan 1, 1972

By Harold L. Rhodes

Vapor-liquid equilibria data for 65-34-1 and 25-27-48 mole percent helium-nitrogen-methane mixtures are presented for 12 temperatures from 76.5° to 164° K and pressures from 100 to 1,200 psia. These data were obtained in a windowed phase equilibria cell equipped with a vapor recirculating pump. Isobaric and isothermal K-values are plotted for both mixtures. Two isometric plots are included.

Jan 1, 1972

By A. B. Hooker, E. J. Coggeshall

"INTRODUCTION Ignitions of gas at the coal face when a blast is fired electrically are often a tributed to the explosive; but sometimes the ignition cannot be explained satisfactorily in this way-in fact, ignitions have occurred when the detonator has failed explode.The possibility of such electrically by sparks from the blast between poorly insulated leading wires and detonator leg have been recognized. Several countries have provided safe types of single-shot blasting units; some have permitted the use of larger multiple-shot blasting units provided each unit is equipped with a time-limiting switch that prevents unnecessarily long application of voltage on the leading wires after the shot has occurred, the assumption being that the firing line will this be dead before damage to the wires and subsequent sparking can take place. An extensive research was made by a French commission relative to the characteristics of electric detonators and methods of firing. Along other tailings they investigated the probability of ignitions by sparks across the leading wired at the face, also the time and duration of the various events in blasting, such as ignition of the detonators, movement of the coal face, and application of firing current. They suggested, as a means of eliminating or reducing tilt possibility of gas ignitions from the blasting unit, that the timing switch of the blasting unit be designed to disconnect the blasting"

Oct 1, 1934

By R. R. Sayers

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try , if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

By J. P. Barkley

"The accompanying tabulation gives the results of a series of operating tests on two types of small stokers. One was an inclined, natural-draft, moving-grate, overfeed ""hand-stoker"" fired and manipulated by hand; the other was. a horizontal, forced-draft, stationary-grate, underfeed, mechanical unit-stoker operated by an electric motor. These were installed as shown by the accompanying sketches (figs. 1 and 2) under horizontal return tubular boilers of a nominal rating of 150 bl.h.p. each.The steam load carried by these boilers was a rather typical heating load. It was fairly constant and of about 30 bl.h.p. throughout the summer months, with small variation between day and night. During the winter months the daily variations were dependent upon the outside temperature. The boilers were banked a considerable part of the night.As noted in the table, two kinds of coal were used. The size of one kind was run-of-mine and the other 11/4 inch nut and clack. These coals from two different mines of the New River district both caked considerably during burning, the nut and slack more than the other. Analyses of the coal were as follows:"

Jun 1, 1929

By A. W. Maynard

Simple chemical spot tests for the identification of major alloying elements in aluminum-base alloys are described. The tests are suitable for use by nontechnical personnel working outside a laboratory. Tests for zinc, copper, manganese, and magnesium employ electrographic sampling methods and sample papers. Use of electrographic sampling in a test for magnesium in aluminum is made possible by using glass fiber filter paper. Differentiations between magnesium and magnesium-silicon alloys of aluminum and between aluminum-base and magnesium-base alloys are made by direct chemical solution tests. Description of a device for obtaining reliable electrographic samples is included. A sequence of testing for identification by alloy groups is given.

Jan 1, 1971

By Donald I. Kurth

This Bureau of Mines report describes the development and application of a computer model of aquifer hydrology associated with in situ leaching of uranium. The model provides uranium resource developers with a simulation of leachant flow characteristics in a preproduction or pilot five-spot leaching operation. Various types of aquifers are modeled using closed form solutions of the partial differential equations describing the change in fluid head (pressure) as the leaching operation is carried out. User-supplied descriptive input consists of aquifer, well, and leachant flow characteristics. Numeric and graphic outputs such as isopressure, iso-velocity, and isotime contours are available. A typical application is shown.

Jan 1, 1978

By Dave P. Cooper, Tim D. Burgess, Dean H. Ambrose

This paper discusses the application of digital human models (DHM) to examine computer generated forces necessary to move specific joysticks by using roof bolter virtual operators to predict the forces experienced on the operator’s upper extremities. Using DHM and simulations of static movements, investigators analyzed predictions of joint moment and joint force effects on virtual operator’s right wrist, elbow and shoulder and compared them to different body dimensions and work postures. This study exemplifies the ease of estimating upper extremity loads on equipment operators using virtual operators and computer models of equipment and work environment. As expected, comparing results of percentage of joint force and moment reduction using the electronic control and of the mechanical control showed that the electronic control had lower joint forces and joint moments over the mechanical control. The average predicted value of the joint moment on the wrist was 1.84 Nm, elbow 7.85 Nm and shoulder 14.55 Nm and of the joint force on the wrist was 5.06 N, elbow 4.56 N, and shoulder 3.67 N. Because the data illustrates low-level forces to move a joystick, inadvertent actuation of the control is addressed. Regardless of the findings, research is still needed on joysticks in real world situations such as an epidemiological assessment of equipment operators in the field before final recommendations and conclusions can be drawn.

Jan 1, 2007

By G. Esterhuizen, C. Karacan

Methane can be a significant hazard in coal mine longwalling operations and extensive methane mitigation techniques are employed by coal mine operators. Reservoir modeling techniques are used to better understand the liberation and migration of methane from the surrounding rocks towards the mine ventilation system. The caved rock behind the advancing longwall face, known as the gob, can contain high void ratios, providing high permeability flow paths to the methane. The gob is progressively compacted by the weight of the overburden, resulting in a reduction in the void ratio and associated permeability. Estimating the permeability distribution within the gob poses challenges due to its complexity. The authors have developed a new methodology to determine both horizontal and vertical variations in the permeability of the gob. Variations of the permeability in the vertical direction are based on a model of caving and block rotation, which considers the effect of block dimensions and fall height on the void ratio. Gob compaction by the overburden and associated permeability changes are determined from a three-dimensional geo-mechanical model which simulates the gob as a strain hardening granular material. The resulting three-dimensional permeability distribution in the gob is then transferred to a reservoir model. The paper demonstrates the application of the method and shows that reasonable results are obtained when compared to empirical experience and measurements.