Search Documents

By Kenneth O. Bayard, John D. Sullivan

"This repot continues the series of papers being prepared at the Southwest Experiment Station of the Bureau of Mines in cooperation with the department of mining and metallurgy, University of Arizona, on factors involved in the leaching of ores. A list of previous publications is given in the bibliography at the end of this paper.Four factors are essential to the leaching of any copper-bearing ore: (1) A solution that will attack the copper minerals must get into the body of the ore particles; (2) the copper minerals must be dissolved by the solution; (3) the solution containing the dissolved copper must find its way out of the voids of the rocks into the main solution; and (4) the copper in solution must be recovered by some means of precipitation.This paper considers the third step -- the extraction of the water-soluble copper. From leached ores. The usual commercial practice in leaching copper ores consists of: (1) Crushing the ore to pass through a screen with approximately one-quarter or one-third inch openings; (2) charging the crushed ore into a fat; (3) adding, usually by upward percolation, a solution that will attack the copper minerals; and (4) washing the copper-laden solutions out of the ore with solutions weaker in copper than the pregnant solution, and finally with water. A countercurrent system of leaching and washing is usually employed. In some plants the solutions are circulated during leaching and washing, and in others they are not. In some plants the wash solutions are added by upward percolation, while at Chuquicamata the so-called ""piston-displacement"" method of washing is employed.The following condensed resume of the leaching cycle of the plant of the Inspiration Consolidated Copper Co. is given to present to the reader a picture of the steps involved in a typical leaching cycle. This plant was recently described in detail.4 The ore, crushed to pass openings 11/2 inches in diameter, passes over a screen with ¼-inch openings. The undersize from the screen goes to a Dorr howl classifier that removes the primary slime from the circuit. The overflow from the classifier is treated in a slime-leaching plant. The oversize of the ¼-inch screen passes through rolls, where it is crushed to pass a 3/8-inchscreen. The undersize from the 3/8-inch screen join with the coarse material from the classifier, and the combined products become the feed to the leaching vats. There are 13 concrete lead-lined leaching vats. The complete leaching cycle is 13 days. Eight tanks are under acid-iron content at all times; three are being washed, one tank is being filled, and the one is being excavated. The electrolyzed solution from the tank house, to which amount of new acid has been added, is put on the oldest tank of ore under need This solution travels from tank to tank and finally emerges from the newest ore"

Apr 1, 1931

By James P. Rider, Charles D. Taylor, Edward D. Thimons

Research was conducted to investigate how ventilation of a mining face is affected when scrubber flow is greater or less than intake flow. Tests were conducted in a full-scale surface test gallery built to simulate a mining entry with a continuous mining ma- chine at the face. Methane gas was released at constant flow at the mining face. Gas measurements taken at six locations near the face were used to evaluate how well the face was being ventilated. Increasing scrubber flow resulted in lower methane levels even when scrubber flow was much greater than intake flow.

By W. H. Ode

In 1949 the Coal Committee of the Economic Commission for Europe, Geneva, Switzerland, established a Classification Working Party, to develop an international system for classifying coal. This project was necessitated by the increased trade in coal among various nations following World War II. Although national classification systems existed, they had been developed to cover the characteristics of domestic coals without reference to coals of other countries. Different terms for describing similar or identical coals in each nation caused confusion in evaluating coals shipped in international trade. Experts from Austria, Belgium, Bulgaria, Czechoslovakia, Denmark, the Federal Republic of Germany, France, Greece, Hungary, Italy, the Netherlands, Poland, Sweden, the Union of Soviet Socialist Republics, East Germany, the United Kingdom, the United States of America, and Yugoslavia participated in various stages of the classification work. Walter A. Selvig was appointed by the Bureau of Mines as the technical expert to represent the United States because of his experience in developing and standardizing methods of analyzing and classifying American coals. He served on the Classification Working Party until his retirement from the Bureau of Mines early in 1956. Extensive laboratory work was done in connection with the classification studies at the Pittsburgh Experiment Station of the Bureau of Mines.

Jan 1, 1958

By Donald C. Strimbeck

The Bureau of Mines designed a down-fired refractory-lined combustor that efficiently burned pulverized coal to produce a gas suitable as working fluid for an open-cycle gas turbine. The gas contained relatively little carbon, so the load on the ash-separation equipment was significantly reduced. Moreover, reduction in carbon content of the gas increased the average density of the solid particles making them more amenable to removal by centrifugation. Centrifugal-type separators failed to remove sufficient ash; however, to limit blade wear enough to achieve operating periods generally deemed necessary for commercial practicability.

Jan 1, 1969

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported4/, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simpliication to determine an economically feasible procedure that would require a minimum of expensive equipment for plant erection and a minimum of reagent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth while to utilize available facilities in a search for difficulties that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 pounds per day of metal and operated under simulated plant practice.

Jan 1, 1938

By R. R. Lowery

This project was proposed to provide information on the hazards associated with arc melting of thorium. A general air-sampling analysis was made to determine the separation, concentration, and distribution of thorium daughter (decay) products throughout arc melting, machining, and forging processes of a thorium handling facility. The value of well coordinated health physics program is stressed in connection with potential health hazards and personnel protection. Building, equipment, and exhaust ventilation requirements for such a facility are discussed. Special handling methods are described for thorium. INTRODUCTION The Bureau of Mines at the Albany Metallurgy Research Center has been involved in handling the naturally radioactive metals, uranium and thorium, for several years. Cooperative work for the Atomic Energy Commission has been carried out with thorium metal, and as a result the concerned laboratories of the Center have accumulated experience on the hazards associated with this metal. This report details the radioactive hazards arising from the arc melting, machining, and forging of thorium.

Jan 1, 1962

By Pablo Velasco

The Belize economy recorded modest growth during 1980; the growth of the gross domestic product (GDP) in real terms was between 1% and 2%. At current prices, the 1980 GDP reached $108 million2. This output was largely attributed to the performance of a few industries, mostly nonminerals. Such performance improved significantly the balance of payments situation by reducing the deficit from $19 million in 1979 to $4 million in 1980. The rate of inflation was an estimated 18% in 1980 and would have been greater if not for a conservative monetary policy and price control on a number of essential items. Expert earnings increased $43 million, or 50%, from the 1979 level. After increasing more than 25% in 1979, imports increased only 6% in 1980 to a level of $141 million owing to the decline in investment and stabilization of petroleum prices. The balance of trade deficit was $9.8 million in 1980, a marked improvement from the 1979 level of $45.1 million. The mineral output for Belize accounted for only a fraction of 1% of the GDP. Such activity was limited to the production of limestone, marl, and sand and gravel, all of which were primarily used in construction of the Northern Highway between Orangewalk and Belize City. Mineral resources are deficient or nonexistent in Belize for the majority of metals and nonmetals, although the Government and others continue to believe that petroleum must exist in Belize. The proximity to Mexican oilfields and the growing finds in the Peters area of Guatemala support this expectation. The Government continues encouraging exploration onshore and offshore and offers terms that

Jan 1, 1982

By Jan C. Still

The Glacier Bay subarea is that part of the Juneau Mining District (JMD) within Glacier Bay National Park and Preserve (GBNP). It is the western portion of the JMD and consists of the land between the Fairweather Range crest and the Takhinsha and Chilkat Ranges crests (excluding that land east of Excursion Inlet.) Figure B-1 shows the area. It is bounded on the north by the Alaska-British Columbia International boundary, to the south by Cross Sound and Icy Strait, and contains Glacier Bay. During 1975 -1977 the Bureau conducted a detailed study of the occurrences, prospects, and deposits in GBNP (B_4).2 This work was in cooperation with the U.S. Geological Survey (USGS) under the provisions of the Wilderness Act (Public Law 88-577). As a follow up to this earlier Bureau work, limited studies were conducted, during 1985 and 1986, as part of the JMD study. This report covers the most important aspects of the earlier studies and the 1985 and 1986 studies. ACCESS The Glacier Bay area may be reached through Gustavus airport, a paved strip which is serviced by scheduled jet airliners in the summer and air taxi services year-round. The airport is connected to Bartlett Cove (GBNP headquarters) by an all-weather road. No other roads exist in the area except a skid road to the LeRoy Mine and mill in the Reid Inlet area. Much of the Glacier Bay area is accessible through the salt water inlets and fjords which are part of Glacier Bay. Cruise ships, charter boats, and fishing boats visit these inlets and fjords during the summer months. Elevations within the area range from sea level to over 15,000 feet in the rugged Fairweather Mountain Range. More remote areas are accessible by small boat, foot, or helicopter. Glacier ice is a year-round hazard to navigation in Glacier Bay, and during the winter months some of the more northerly inlets are frozen.

Jan 1, 2012

By Jerry B. F. Champlin

The successful injection of liquids into subsurface permeable formations for production stimulation, storage, or waste disposal requires a rapid, precise, and accurate method of determining the permeability of porous solids. This report describes a method and apparatus, developed by the Bureau of Mines, that use the principle of specific-volume permeametry. Calibration of the apparatus over a wide range of permeabilities and standardization of several apparatus constants have eliminated many of the tedious calculations and problems of manipulation common to some other methods. Improvements in reproducibility and accuracy have resulted from reducing experimental measurements to one parameter--time. Specific permeabilities of reservoir rock samples are determined directly from a chart that relates elapsed time to a permeability equivalent to that determined by bubble-tube measurements.

Jan 1, 1962

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By J. M. Davidson

The potassium mineral polyhalite (K2SO4.MgSO4.2CaSO4.2H20) found in large deposits in western Texas and southeastern New Mexico is associated with varying amounts of halite (sodium chloride, NaCl) and anhydrite (calcium sulphate, CaSO4). Although the anhydrite, because of its low solubility and slow rate of solution, is relatively inert, the halite is dissolved immediately in any process solution with which the polyhalite comes in contact. Limited quantities of sodium chloride in the liquors used for the hot extraction of polyhalite materially improve the results obtained,4 but only a very small sodium chloride content may be desired in the entering polyhalite in other procedures, such as Bureau of Mines process 75. In. all of the processes suggested for the recovery of potassium sulphate from polyhalite the control of the sodium chloride content will be desirable, if not absolutely essential to efficient operation. OCCURRENCE OF HALITE IN POLYHALITE A preliminary estimate of the amount of halite associated with typical deposits of polyhalite may be derived from drill cores, although it should be remembered that only 50 or 60 core tests have been made in the many hundreds of square miles of the Permian basin. From a mineralogical study of 41 of these cores, Schaller and Henderson6 state: In many of the sections of core that seem when viewed by the unaided eye to consist essentially of polyhalite, both halite and anhydrite are present in greatly varying quantities - with very minor quantities of clay and magnesite.

Jan 1, 1934

By R. S. Dean

[Methods s of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made e before the turn of the century, used Moissan's pyrophoric man manganese.3/ This material was made b; electrolysis into a mercury cathode and distillation in vacuo. The material was essentially pure, and investigations in which it was employed (with proper precautions against oxidation) led to accurate results on tie intrinsic behavior of metallic manganese.]

Jan 1, 1941

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By G. R. Fitterer

In the manufacture of steel by any process the refining period involves the partial elimination of the metalloids carbon, manganese, phosphorus, and silicon, by virtue of their reactions with ferrous oxide. At the end of this refining stage the metal consists chiefly of iron in which small amounts of these materials are dissolved. Unless some deoxidizer is added to the steel at this time, the reaction between carbon and ferrous oxide will continue with such force that it is impossible to form sound steal in the ingot molds. Instead, the product will exhibit a marked porosity due to the formation and trapping of carbon monoxide-the product of the reaction mentioned. However, if deoxidizers are added, steel may be obtained which is dense and free from gas bubbles. At the same time the deoxidation products will remain in the steal as impurities. For example, silicon additions form Si02 or combinations of Si02 and FeO. Additions of manganese form deoxidation products consisting of various proportions of MnO and FeO. It is also quite obvious that simultaneous additions of manganese and silicon will form oxide combinations either in the binary system MnO-SiO2 or in the ternary system FeO-MnO-SiO2. Work at the Pittsburgh Experiment Station of the United States Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board, involved the study of such deoxidizing reactions and their products. In this connection considerable information is necessary concerning FeO, MeO, Si02, and Al 203, and their various combinations. Some of the most needed data are the melting points of all of these materials. At the outset of this work ordinary methods of melting point determinations were found to be inadequate for various reasons, and the procedure finally selected involved the use of the micropyrometer with occasional corroboration by quenching methods, The reasons for this selection, together with a description of the apparatus, are given in the following pages.

Jan 1, 1932

By Walter C. Lorenz

In connection with its renewed study seeking solutions to problems created by release of acid water from bituminous coal mines, the Bureau of Mines recently surveyed reports already written on the subject. This publication is based on that search. The Problem Poor distribution of water is evident on an ordinary geographic map of the United States. The more abundant supplies of surface water appear to be centered in the northeast, the southeast, and the central humid areas of the country. It is in the midst of this abundant surface water, in the Ohio River Valley, that most of the bituminous coal is mined. Varied industry has located in the valley to use the coal and the river. The coal is a source of power and o raw material. The river provides transportation for raw and finished materials; equally important, it provides the water that is used for cooling and processing in manufacturing. It also serves as a vehicle for the disposal of waste.

Jan 1, 1962

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

By Henry C. Meeves

The nonpegmatitic sources of beryllium in Arizona, Colorado, New Mexico, Utah, and four adjacent states investigated by the Bureau of Mines are described. The investigations included 155 properties from which over 6,200 rock samples were collected; more than 5,500 samples were analyzed by the nuclear beryllium-detection technique. Twenty-four of the properties examined had rock containing more than 0.10 percent BeO. Many of the beryllium determinations were made in the field with portable detection instruments by direct scanning of outcrops and by testing samples of rock brought to the instrument. The large domestic resources of low-grade nonpegmatitic beryllium ore in Utah, which were discovered by private enterprise and which respond favorably to small-scale treatment processes, may come into commercial use and thus reduce the dependence of the United States on imported beryl.

Jan 1, 1966

By A. B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker?s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

Jan 1, 2006

By John D. Sullivan, Alfred P. Towne

"In copper percolation-leaching plants the ore is usually crushed to a maximum size of about three-eighths inch. Ordinarily an ore is crushed as finely as feasible since the rate of extraction of copper is increased with decreasing size of particles owing to the greater surface exposed and. the shorter path required for solutions to come into contact with the minerals to be dissolved. However, greater degree of crushing also increases the amount of fines. When ores are charged into leaching vats the coarse and fine material tend to segregate, resulting in channeling of solutions and leaving the areas where fines predominate only partly leached. An improvement in the method of charging the ore into vats that would minimize the deleterious effects of the segregations of fines would increase the percentage extraction of copper.The Inspiration Consolidated Copper Co.4 recently installed classifiers to remove the primary slimes from the ore, before charging it into the leaching vats. This necessitates a separate agitation treatment for the slimes.Recent publications5 of the bureau have shown the advantages of agglomeration followed by trickle leaching to extract copper from concentrator tailings. It was shown that when equal parts of ore crushed to about 1/4-inch size and concentrator tailings were agglomerated with approximately 10 per cent of moisture, either in the form of water or leaching solution, and the mass was charred into a leaching vat the ore could be treated successfully by open-drainage trickle leaching. Even with 30 or 35 per cent of minus 200-mesh material present the ore could be leached, if it was not flooded with solution.The results obtained in agglomerating ores and slimes suggested the possible advantages to be gained by wetting the crushed ore for standard percolation-leaching plants before charging it into the vats. Wetting the ore whould make the fine material and slime cohere to the larger pieces of ore thus tend to prevent segregation when the ore is charged into the vats. The bureau, at its southwest Experiment Station and in cooperation with the Department of Mining and University of Arizona, Tucson Ariz., therefore made a study to work: out A way in which slimes could be handled in percolation leaching. The study showed that the method of charging ore into the leaching vats governed the distribution the fines and consequently the rate extraction of copper. The results of the study reported in this paper."

Feb 1, 1931

By R. V. Ramani

The overall objective of this study is to contribute to the reduction of the quartz dust hazard in underground coal mines through a better under-standing of the sources and generation of airborne quartz dust. This research project has included extensive experiments in operating mines for (1) documenting the amount of respirable dust generated, (2) measuring the quartz levels in host materials and airborne dust, (3) analyzing the size consist of the mined product, and (4) establishing the relationship between these various parameters. The results of the study indicate that the amount of dust airborne is a very small fraction of the total (<15 µm) and respirable (<7 µm) dust generated. The quartz contents in the total and respirable airborne dust are generally higher than those in the host material. Quartz content increases with decreasing size of airborne dust. Also, it appears that rock breaks into a different size distribution than coal. The source of quartz for the airborne dust appears to be the roof and the floor material rather than the coal seam itself. No general relationship is found between the Hardgrove Grindability Index and either the quartz content in the airborne dust or the amount of respirable dust. Extended descriptions of the experimental design, the experiments, data analyses and results are presented in this volume. The raw data, the data management computer program and the sampling and safety plan are presented in Volume 2.

Jan 1, 1987