Search Documents

By Albert W. Deurbrouck

This report describes preparation characteristics of significant coalbeds in Tazewell County , Va . In 1961 Tazewell County produced 933,110 tons of clean coal from six coalbeds ; the Lower Banner , Raven , Jawbone , Upper Seaboard , and Pocahontas No. 3 and No. 5. Samples from all of these beds , except the Lower Banner , were included in this study plus a sample from the Pocahontas No. 4 bed . Of the samples collected , only one would require upgrading to be of metallurgical quality . The coals ranged in rank from high- volatile -A to low- volatile bituminous .

Jan 1, 1963

By J. F. Barkley

Field tests were made on the rate of corrosion of 30 materials used in air preheaters under regular operating conditions, and the buildup of deposits was observed. Twenty-three materials were tested with coal as the fuel on an underfeed stoker and seven with oil, including a short period with pulverized coal as fuel, The plant equipment is described, and pertinent plant operating data are tabulated. Figures 17 and 19 (pp. 24 and 27) give the results of corrosion tests on the uncoated metal test specimens. The information obtained from these tests follows the general pattern described in Bureau of Mines Report of Investigations 4996, Corrosion and Deposits in Regenerative Air Preheaters. The deposits were similar, and the corrosion rates of Cor-Ten and Mayari-R steel (previously found to be essentially the same at the Harding Street Station using coal) continued to show little difference at the Marion Generating Station using principally oil. The one high-alloy steel tested, type 321, showed a much higher corrosion rate than the low-alloy steel, Cor-Ten.

Jan 1, 1959

By R. G. Meara, O&apos

The land-pebble district of Florida, which in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of Sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of limey or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the rushing and formerly lost supplied the feed.

Jan 1, 1931

By Arnold B. Hubbard

This report describes a method of concentrating the insoluble organic material (kerogen) in a rich Colorado oil shale without any apparent alteration of its original chemical form. The method involved treating finely pulverized shale with dilute acetic acid at room temperature to remove the carbonates, which act as a cementing agent for the shale, and cause the shale particles to partly disintegrate into the organic and inorganic components. The acid-treated shale then was centrifuged in different liquid mediums ranging from 1.4 to 1.15 gravity to effect a mechanical separation. From a Colorado oil shale containing 48.0 percent ash, kerogen concentrates containing 43.3 to 8.7 percent ash were obtained. The carbon:hydrogen ratios of the kerogen in the original shale and the different concentrates were essentially the same. The oil:kerogen ratios calculated from Fischer assays of the above samples were essentially the same, regardless of the organic or inorganic contents. This was also true of the assay water:kerogen ratios of the same samples. These data indicate that no significant change occurred in the kerogen during the concentration process.

Jan 1, 1952

By Albert W. Deurbrouck

Twelve samples from six Barbour County coal beds were analyzed for this report. The samples collected were generally high sulfur content coals, frequently exceeding 3 percent in the raw-coal sample. Many of them could not be upgraded to acceptable metallurgical standards even by rigorous preparation procedures. The production of coal in the county in 1963 amounted to almost 3 million tons of which 44 percent was mechanically cleaned.

Jan 1, 1965

By Jonnie M. Estes

A two-constant equation is presented for helium from 30° = T = 1,473° K. This equation is developed by modifying a generalized equation of state originally presented by Redlich and Kwong (20).3 The modification consists of setting B = 0.06372 Tc/PeT. This modified equation represents the compressibility factors of each of 80 isotherms tested in this temperature range to less than 1 percent average deviation.

Jan 1, 1967

By Lucien Eaton

The mining methods described in this paper are those used in a large mine producing hard specular ore on the Marquette Range in the Upper Peninsula of Michigan. Although the conditions of mining are unique in this district, they are similar to those in many other districts, and information in regard to the methods used and the results obtained should be of interest. The methods now used are an outgrowth of those of former years which have been adapted to conform with improvements in mechanical appliances, changes in the wage scale and labor supply, and the' selling price of the product. The mine is situated' at Ishpeming, in the Upper Peninsula of Michigan, 16 miles west of Marquette, its shipping port on Lake Superior.

Jan 1, 1929

By Robert W. Freedman, Robert L. Craft, William G. Humphrey

As part of a continuing effort to reduce the weight and bulk of equipment that mining personnel must carry underground, the Bureau of Mines and the Mining Enforcement and Safety Administration (MESA) investigated accurate and convenient gas samplers for use by mine inspectors in sampling mine atmospheres. The samplers are septum-stoppered glass vials commonly used for routine blood sampling. These lightweight, compact samplers yield results comparable with those obtained with conventional bottle samplers of 250-ml nominal capacity.

Jan 1, 1975

By Robert W. Smith

In a certain application2/ it was necessary to compute the beta function B(p, q) for a certain set of values p and q. Since t he set of p and q values was much mo re finely spaced than those in any published tables, the authors decided to make their results available in this report. In connection with this application the functionB(p, q) was needed at various points in the p, q plane at intervals of 0.05, 0.05<p = q< 10.00. Fletcher, Miller, and Rosenhead2/ state that the only tables available in the desired range are those of Rearson.4/ However, the interval used by Pearson was not small enough for the present application. For this reason it was decided to calculate B(p, q) for p = q =0.05 (0.05) 10. 00.2/ This table is published because of the fundamental importance in mathematical analysis of the complete beta function.

Jan 1, 1953

By William Y. Mo

This report presents preliminary results of a study undertaken to investigate quantitative characteristics of the demand for steel mill products and its major end-use components. The major end uses included in the study are the steel mill products used in construction, in automobiles, in producer durables, and in consumer durables. The main objectives of the research underlying this study are as follows: (1) To formulate and estimate the empirical demand relations for steel and the four major end uses in the United States; (2) to measure and calculate the responsiveness of the U.S. per capita steel consumption with respect to the changes of the steel and other nonferrous metals prices; (3) to determine and quantify the relative importance of the underlying demand explanatory factors in contributing to the average year-to-year increases (or decreases) of the U.S. per capita steel consumption; and (4) to adapt and use the estimated demand relations in making projections of the U.S. future demand for steel and the major end-use components. After extensive preliminary investigation, three versions of simple linear demand relations are selected and estimated by means of ordinary least squares (OLS) method. The annual data for the period 1947-65 are used in the estimation. Direct and cross price elasticities of demand are computed for each of major end uses. The relative importance of demand explanatory factors in contributing to the average year-to-year changes of U.S. per capita steel consumption are also calculated. For making projections, a simple autoregressive time trend model is used in estimating the future values of independent variables. Since the estimated demand relations are valid for projections only if the estimated parameters can be assumed to be unchanged in the future, and consequently, the projections derived in the study should be interpreted accordingly.

Jan 1, 1970

By Robert A. Speirer, Richard G. Burdick

Methods of detecting geologic faults and other linear features by means of processed LANDSAT satellite images have gained prominence during the past several years . There have been numerous programs written to pick these " lineaments , " but they have been almost universally tailored to large computers . This Bureau of Mines report describes a detection method developed for use with a minicomputer . The method comprises a suite of programs that scans an image for all " potential " lineaments . From this partially analyzed data , the final lineaments are picked by another routine . The method was field tested in an area of south- central Wyoming , and results indicated good agreement between computer- picked lineaments and ground features . Most of the known geologic faults in the area were picked by the method . Such features as roads and trails were also picked but were easily distinguished from faults during field inspection . The method is relatively new but promises to be a viable reconnaissance technique for the mining industry in geologic structural analysis .

Jan 1, 1965

By John M. Devine

Hydrogen sulphide associated with natural gas was noted as early as at Point Albino, Canada. The presence of this impurity was recognized also in other of the earlier oil and gas fields, although the occurrence was by no means common. However, in recent years, with the development of the producing zones of test Texas and the Texas Panhandle, the Production of "sour" crude has increased greatly and hydrogen sulphide has proved a generally troublesome factor--frequently a major problem--in the drilling and operation of many wells in those areas. The problems arising from the drilling and producing of oil or gas wells in hydrogen-sulphide areas, fall under two general divisions: safety problems and corrosion problems. Mention is made of a third division which is closely related to the other two, that of treating--or the development of processes for the removal of hydrogen iron the standpoint of safety and health hazards, hydrogen sulphide in the petroleum industry has been discussed in a number of publications. Likewise, the problem of hydrogen-sulphide corrosion of production equipment has been given considerable attention in the literature.

Jan 1, 1931

The Bureau of Mines has long been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts, the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions1 issued by the Bureau of Mines, and the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. The Government, with the exception of the Tennessee Valley Authority, purchased approximately 5.5 million tons of coal in fiscal year 1971. In connection with these purchases, the Bureau analyzed 4,366 samples. These are published (table 1) for the use of Government officials and the public. Such analyses of delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1972

By C. F. McCarroll

[Laboratory research and, control in the u?odnction an; utilization of petroleum and its product s have eqLmde& greatly during the past decade, rind much of the routine control and experimental equipment noirr requires the con-stant daily use of liquid nercury. In spite of this greater use, very little consideration has becn given to the hazard that might be occasioned by the toxic vapors of mercury unavoicl.a~l.p spilled or otherwise exposed to the atmosphere during the normcl 2rgced1u.e of ln30r~tor;~r operations. A sfmple visual exami~stion gf&apos; sone of the laborztories reveals the prescnce of a considerable quantity of mercury in the craclcs of floors, on work tebles, ad on and mo7md eql~ipmeilt st.ads. Usually this yercurj ie contaminated with oily and dirt BO th~t it remint; in R finely divided state and a srnarl amount presents a relativell- lag? surface for evaporation. Since mercury shows meas~rable vo!-atility st a tempero.turc as lor^ 2s 8.5O F., mercury vapor will bo present in the atnosphere of anjr laboratory wbr.e mercury is exposed. promiscuously]

Jan 1, 1939

By Miles B. Royert

Crude Minnesota taconite was charged in the Bureau of Mines experimental blast furnace so that smelting characteristics of such highly siliceous raw materials could be studied and smelting costs compared with those of a standard Mesabi ore. The Bureau recognized that the highly siliceous nature of the crude ore and its relatively low metallic content would be serious economic deterrents to commercial use of the raw taconite, but compensating factors would be low capital investment in production facilities, large tonnage available on short notice, high recoveries of iron, and low delivered cost. Crude taconite smelted readily in the experimental blast furnace. Coke consumption per ton of metallic product was very high, compared with the average established requirements for smelting normal grades of metalliferous raw materials. Slag rates were also inordinately high. Metal quality was erratic as to silicon, and sulfur contents were objectionably high.

Jan 1, 1961

By R. H. King

A very simple cold-bend test was devised and tested for evaluating thermoplastic jackets used on mine-power-feeder cables. A test sample is bent into a semi-circle whose radius is equal to the minimum bend radius recommended by IPCEA and then cooled to the, desired test temperature (-35°C). While at temperature, the sample is straightened by pulling the cable ends with a winch arrangement. The results show that of the jackets tested, those which cannot withstand the test literally burst when the sample is straightened.

Jan 1, 1978

By Frank J. Wiebelt

The Veta Chica and Cerro Colorado chromite deposits of the McGuffy Creek area, Siskiyou County, Calif. were selected as worthy of investigation by the Bureau of Mines in accordance with the Strategic Minerals Act of 1939. These were two of many chromite deposits examined by engineers of the Bureau of Mines during their extensive wartime mineral examination and exploration campaign. Exploration by the Bureau of Mines consisted of 2,234 feet of diamond drilling, surface trenching, and sampling during the months of May and June 1942.

Jan 1, 1949

By Stephen Gerard Sawyer

A Fortran IV computer program entitled WAVE, which employs an explicit finite difference scheme for solving the one-dimensional wave equation for a time-dependent inelastic rock has been developed. The viscoelastic properties of the rock are represented in terms of a generalized Voigt model. The theory on which the computer program is based is rederived and a short description of the program is given. The computer program input instructions, a listing of the computer program, and example problems with required input and subsequent printed output are presented in appendixes. In the example problems) calculated results are free of spurious oscillations which occur in certain other methods of numerical calculation) notably the extended Ritz method.

Jan 1, 1972

By Stanton L. Tainter

When the disruption of gold mining stopped the usual source of siliceous flux needed by copper smelters , sandstone copper deposits in northern Arizona offered possibilities as a source of the flux during the war emergency . The Federal Geological Survey , while making a comprehensive survey of sandstone copper deposits , investigated the Warm Springs mining district in northcentral Coconino County in August 1943. A month later , J. H. Hedges , chief of the Tucson Division , Mining Branch , Bureau of Mines , examined the operations in connection with an application for an access road . Both investigations concluded that the district , as an emergency source of copper-bearing siliceous flux , had considerable merit , provided high prices for copper continued in effect . Early in 1944 , V. M. Ryan and S. B. Atherley requested assistance from the Bureau in exploring various deposits on their property . The Bureau / drilled 152 holes , aggregating 3,756 feet , on the Petoskey and Mackin groups of claims . This report is based upon churn drilling done under contract from October 7 to November 25 , 1944 .

Feb 1, 1947

By E. W. COCHRANE, R. HOPKINS, G

The number of completed petroleum refineries in the United States continued to decline in 1938, but the total capacity to process crude oil increased materially. This information was obtained in connection with the Bureau's annual canvass of refinery capacity as of January 1, 1939. In spite of the addition of a half dozen plants in Illinois and the inclusion in this year's list of several more "pot-stills" in Montana, the total number of plants, and inactive, declined from 551 on January 1, 1938, to 538 on January 1, 1939. was entirely in shut-down plants, as the number of operating plants rose from both active The decline 431 to 435. Yost of the plants dismantled were situated in Wyoming and Texas, parts or several from the latter being transported to Illinois. About 10 more East Texas refineries were dismantled in 1938, leaving about 15 plants in the field, only 8 of which were operating on January 1, 1939. Although the total completed capacity increased from 4,351,151 barrels on January l, 1938, to 4,508,555 barrels on January l, 1939, the operating capacity declined, and the inactive capacity increased about 50 percent, or from 380,955 to 574,770 barrels. These shifts in capacities reflect the comparative slump in the refining industry in 1938 after the prosperous year 1937. Daily average crude runs in 1938 were 3,192,000 barrels, from which it may be figured that the operating ratio for the active units was about 81 percent of crude and for all completed equipment 74 percent. The highest daily throughput in 1938 was about 3,400,000 barrels, at which time the reserve capacity represented in the active equipment was at least 500,000 barrels, in addition to about that much capacity shutdown. In an emergency, much more reliance could be placed on the reserve capacity of the active equipment, as much of the shut-down capacity is obsolete at present specifications and prices. Regarding obsolescence, the refiners reported 418,165 barrels of their idle capacity in good condition on January l, 1939 and 156,605 barrels in poor condition. However, it is probable that the former reflects an optimistic viewpoint. Refinery activity, as represented by new construction and dismantling, declined materially in 1938. The new capacity added in 1938 was 378,350 barrels compared with 394,680 barrels in 1937. Probably 1939 will see a much larger decline, as the new capacity under construction on January 1, 1939, totaled only 142,250 barrels compared with 283,020 barrels the preceding year. The capacity represented by the new plants was negligible throughout

Oct 1, 1939