Search Documents

By R. W. Smith

The Bureau of Mines has been engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies were designed to provide basic thermodynamic information of high accuracy, facilitating the theoretical study of flame and combustion phenomena.4 This report is the fifth of a series5/ presenting results of the study for particular fuel-oxidant systems. These calculations have as their objective the constant pressure flame temperature of acetylene-air for a range of pressures.

Jan 1, 1954

Increase the productivity of domestic mining operations by improving the performance of rock drilling systems. Approach Investigate the use of chemical solutions at zero surface charge concentrations as drilling fluid additives to enhance penetration rates and extend bit life. Background Bureau researchers have investigated the use of chemical additives to enhance drilling performance and have found that the most efficient drilling occurred when the drilling fluid was able to maintain a zero surface charge (ZSC) on the rock surface. Laboratory drilling studies using 5/8-inch diameter diamond-impregnated coring bits on rock types such as quartzite, granite, taconite, and marble. Cationic compounds were used as the surface charge neutralizing additives during these tests. The drilling studies demonstrated enhanced drilling performance, however, only at the singular additive concentration that produced the ZSC condition. Bureau researchers made a breakthrough when they found that polyethylene oxide, although a nonionic polymer, was able to maintain the ZSC condition over a wide range of concentrations. Success using polyethylene oxide as the drilling fluid additive during subsequent laboratory tests prompted testing under field conditions.

Jan 1, 1991

By K. E. Tame

As part of a Bureau of Mines survey of radioactive waste disposal , a laboratory investigation was made to study such problems in carbonate leaching mills . Because uranium concentrators employing carbonate leaching with caustic precipitation normally recycle barren solutions to the washing circuit , the disposal of liquid radioactive wastes is automatically controlled . However , it was deemed important to determine the actual radium 226 concentrations occurring in this type of milling so that the survey of the entire industry would be complete . The laboratory procedure consisted of leaching the ground ore at 85 ° to 90 ° C and 50 pct solids for 6 hours in a sodium carbonate - sodium bicarbonate solution . The pulp was filtered to obtain a pregnant solution that was reacted with sodium hydroxide to precipitate the uranium as sodium diuranate . Regeneration of the barren solution was accomplished by gassing with carbon dioxide . The solution then was reused by advancing the solution through the washing to the leaching operations . The radioactivity in the pregnant solution was unusually high , averaging 6,500 disintegrations per minute ( dpm ) of radium 226 per liter . However , over 95 pct of the radium was precipitated with the uranium . Consequently , no buildup of radium occurred upon reuse of the barren solutions for washing .

Jan 1, 1964

By Benjamin W. Haynes

Materials from phosphate rock mining and processing were analyzed for fluorine and uranium content as part of the Bureau of Mines program to more effectively recover resources from mining and mineral processing reject materials. The analysis of both feed and waste materials generated in the beneficiation and acidulation of phosphate rock was performed to obtain information on the disposition and concentration of these elements in phosphate rock processing streams. Fluorine was determined by a distillation-titration method and by ion chromatography. Uranium was determined by the dibenzoylmethane (DBM) method, the reliability being confirmed by roundrobin analysis of samples within Bureau of Mines research centers. National Bureau of Standards (NBS) Standard Reference Material (SRM) 120b-Phosphate Rock was also analyzed for fluorine and uranium to verify procedures and results. Fluorine values ranged from 0.3 wt-pct in gypsum filter cake to 3.7 wt-pct in phosphate rock concentrate. Uranium ranged from less than 5 µg/g in gypsum filter cake to 200 µg/g in a dried clay slime.

Jan 1, 1981

By J. S. Dunning

Recent developments in energy conversion, mining and minerals processing, pollution control, and chemical equipment have placed in-creased demands on heat-resistant alloys. Higher corrosion rates from oxidation, hot corrosion, and sulfidation have increased consumption of materials that contain critical and strategic minerals and in many cases have limited productivity. The Bureau of Mines is conducting re-search on substitute materials having greater resistance to high-temperature corrosive atmospheres above 6000 C compared to austenitic stainless steels such as AISI 304, 316, and 310, with the goal of conserving critical metals such as Cr and Ni. The substitute materials are based on Fe-Cr-Ni-Al compositions. Aluminum additions to Fe-Cr-Ni alloys significantly improve high-temperature corrosion resistance, particularly sulfidation resistance. In the alloy, devised by Bureau researchers, aluminum additions are held in the form of a second-phase precipitate, 8NiAl. Minor additions of Ti, Mn, and Si improve workability.

Jan 1, 1984

By K. O. Bennington

[Thermodynamic properties of two amphibole asbestos minerals were determined by the Bureau of Mines. The enthalpies of formation were determined by the hydrofluoric acid solution calorimetry method. Heat capacity measurements were made with an adiabatic calorimeter over the range of 5 to 315 K. High-temperature enthalpies above 298 K were determined with a copper-block drop calorimeter to 852 K for amosite and to 902 K for crocidolite. Thermodynamic data determined for amosite of the composition Fe5+2.2766Mg1.5209 Fe+03.12Mn0.0825) Si7.9163Al0.0837022.0363)(OH)1.9637 are: S°298 = 168.8 ± 5 cal/deg-mole; ?Hf°298-15 (elements) = -2419.24 ± 2.95 kcal/mole; ?Hf298.15 (oxides) = -30.92 ± 2.47 kcal/mole; and ?Gf° -2260.1 kcal. Corresponding data found for s3 ,1s = crocidolite of the composition (Na1.9Ca0.1)(Fe2+.024Fe2.5 01Mg0.475) (Si7.9713024Fe+2 2.501Mg0.475) (Si7.971 Al0.029022.095) (OH)1.905 are: S2.98-15 - 161.1 ± 4 cal/deg-mole; ?Rf° 2 298.15 (elements) = -2433.56 ± 2.99 kcal/mole, 10298.1s (oxides) = -87.69 1.70 kcal/mole, and ?Gf°298.15 = -2269.8 kcal.] Calorimetric values from this investigation were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of the measurements. Tables of enthalpies of formation and Gibbs energies of formation are given as a function of temperature both from the elements and the constituent oxides.

Jan 1, 1978

By H. C. Miller

The removal of the mud sheaths that are deposited against the faces of productive oil sands during rotary drilling is one of the important problems confronting operators, especially in semidepleted fields where formation pressures are low. Unless the mud sheaths behind the perforated oil strings and, liners are removed and the sands exposed, oil cannot enter the wells. Consequently much oil that otherwise eight be produced from low-pressure sands is trapped and never recovered. Various types of perforation washers, down swabs, and agitators are used at present for breaking down the mud sheaths and. removing the disintegrated clay particles from wells after the perforated pipes have been inserted. Mechanical methods for removing mud sheaths are quite satisfactory, but prompted by tie request of certain operators in the California oil fields Bureau of Mines engineers have conducted a series of laboratory tests with the view of developing a chemical method for removing mud sheaths in oil wells that will be applicable to field conditions.

Jan 1, 1934

By M. E. Adam

This report describes the construction and testing of large (30 ft high by 55 ft wide) stopping and overcast structures in an oil shale mine. The work was undertaken to develop construction techniques and cost data, and to measure leakage rates on full scale structures in an oil shale mine. A design data base was developed by reviewing industry practice, oil shale industry plans, and technical literature. Alternate layouts for room and pillar mining were examined to find ways to reduce the size and number of ventilation control structures. Six full size stoppings and one overcast were built in the Colony Pilot Mine. Leakage rates were measured using both SF6 tracer gas techniques and the ?brattice window? method. The leakage was measured both before and after a full scale face blast. Blast air pressures were measured across two of the stoppings. Cost and leakage data were used to evaluate the projected overall performance of various combinations of the stoppings in a two-panel oil shale mine.

Jan 1, 1986

By Charles S. Allbright

This report describes hydrogenation of petroleum distillate fuels in bench scale equipment and the effects of hydrogenation on the storage stability and the composition of the fuels. Two distillate fuels were hydrogenated in laboratory equipment using a commercially available cobalt molybdate catalyst. Reactor temperatures were varied from 600° to 850° F and pressures from 100 to 600 psig. Product fuels were analyzed by ASTM, Bureau of Mines, mass, and infrared methods. Hydrogenation of a catalytically cracked fuel from Oklahoma crude oil significantly improved the storage stability, reducing insoluble gum formed during 9 months of storage at 110° F from 19.0 to 1.3 mg per 100 ml fuel, average. Conversion of the olefins to other hydrocarbon types varied with the temperature of hydrogenation--at 700° to 850° F the conversion was mainly to aromatics, at 650° F about 50:50 to saturates and aromatics, at 600° F principally to saturates. Processing a fuel composed of a mixture of virgin distillate and catalytically cracked stock, both from Illinois crude, at 700° F and 200 psig effected marked improvement in stability; the buildup of insoluble gum in storage was lowered from 18.3 to less than 1 mg per 100 ml fuel.

Jan 1, 1967

By D. E. Hirsch

The Bureau of Mines, as a part of American Petroleum Institute Research Project 60, Characterization of the Heavy Ends of Petroleum, has made extensive use of gel permeation chromatography (GPC). Data developed in this study were used to develop several correlations that greatly expanded the usefulness of GPC and the data have been used as an aid in the interpretation of mass spectra (MS). GPC retention volume data on pure compounds were used with molecular structure to develop correlations that can be used to accurately predict retention volumes, molecular volumes, densities, chain lengths, and ring numbers of many components of petroleum without resorting to further laboratory experimentation. Conversely, the correlation can be used to select or reject some compounds from several possible compounds that are indicated on the basis of MS analysis. The utility of these correlations in compound type characterization is demonstrated by showing their application to 330° to 550° C fractions from a low-sulfur and a high-sulfur crude oil.

Jan 1, 1974

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide alumina production capacity by plant and country. The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1993. Capacity data represent announced installed and planned capacities and do not necessarily reflect a Bureau of Mines judgment of actual plant operating levels or timing of planned expansions, The year-end capacity is the ?nameplate" capacity or estimated production capacity, whichever is larger.

Jan 1, 1993

By G. W. Jones

In the course of experiments on the stabilization of acetylene gas by addition of other gases, notably hydrocarbons such as methane, propane, and butane, it was observed that large quantities of carbon black are produced during the explosion of acetylene or mixtures of acetylene with the, above hydrocarbons, the added hydrocarbon being essentially decomposed into hydrogen and carbon. It is known that in the complete absence of air acetylene explodes upon application of an intense ignition source at pressure above 5.9 p.s.i. gage. The same is true of mixtures of hydrocarbons and acetylene. However, the pressures necessary for explosion are considerably higher in the case of these mixtures and depend on the amount of added hydrocarbon. The present report contains data on gaseous products and the physical characteristics of the carbon black formed by explosion at elevated pressures of various mixtures of acetylene and hydrocarbons as well as other gases, such as hydrogen, helium, nitrogen, and carbon dioxide.

Jan 1, 1950

By Wallace W. Roepke, Jon I. Voltz

"The Bureau of Mines determined coal-cutting forces and primary dust generation of four styles of radial gage bits as used on end rings of continuous mining machines. Direct comparisons for reference were made with two widely used conical plumb-bob types having 60° and 90° (nominal) included tip angles. The cutting forces for all of the gage bits were similar to those of the 60°-tip plumb-bob bit. All bits except the RAD-3 gage bit generated similar amounts of primary total dust at shallow cutting, but during deeper cutting, the amounts varied and the gage bits produced as much as 2-1/2 times the dust produced by the 60° bit. This seems atypical since past experience has always shown differences in dust generation at shallow cutting. The specific energy was more like that found previously with other bits, since the values were spread at shallow cutting but became nearly similar at deeper cuts. The 90° bit and the RAD-3 gage bit are not recommended for use except in extremely difficult cutting conditions where dust and forces are of secondary importance. The choice among the remaining four bits can be made on the basis of dust, energy, forces, or cost, as circumstances dictate. INTRODUCTIONThe Federal Coal Mine Health and Safety Act of 1969, with revisions in 1977, was enacted to ensure more healthful and safer working conditions for miners. The Bureau of Mines coal-cutting research facility at Twin Cities (MN) is examining fundamental aspects of the cutting system, including generation of primary dust causing pneumoconiosis in miners and ignition of methane by the frictional impact of cutting bits used on continuous mining machines (CMM's). The cutting system is defined as the cutter-mineral interface area with all its variables, e.g., forces, speed, cutter geometry, bit-mounting geometry, and wear. It has become obvious over the past several years that the cutting system directly affects the economics and design of the ""total system,"" which is defined as all areas of the operation, from the mine face to the preparation plant, which support the mineral recovery by cutting tools to obtain a salable product."

Jan 1, 1983

By E. C. Pattee

A mobile spectroscopic laboratory was completed by the Bureau of Mines in 195 to provide a rapid, inexpensive means of field testing samples for beryl¬lium and other associated metals of possible commercial importance. Spectro-copes have been used in laboratories for many years in various types of research and routine analyses, but this spectroscope is probably the first mobile unit. The laboratory provides for spectroscopic, radioactivity, fluorescent, and limited chemical tests of samples. The unit has been a valuable reconnaissance tool. It has been used to search for beryllium, cesium, columbium, tantalum, rubidium, and lithium in Idaho, Washington, and Montana. Several very low grade deposits of these elements were found, and occurrences of other important elements were identified; however, none are of economic importance. The spectroscope permits the detection of elements by analysis of visible light produced when elements in a small powdered sample are volatilized in an electric arc., A total of 70 elements can be detected; 29 can be detected at or below 0.01 percent, Electric power for the arc is supplied by a gasoline motor-driven generator, Equipment is housed in an aluminum van, mounted on a 4-wheel-drive vehicle for easy maneuverability on mountain roads, A trailer with crushing, pulverizing, and splitting equipment permits the reduction of samples to a small representative pulp.

Jan 1, 1963

By N. S. Dalal, X. Shi, P. M. Gannett

"Chromates are known to induce tumors (1, 2), mutations (3), and DNA damage (4-6). However, the underlying biochemical mechanism(s) is (are) not fully understood (6). Recent studies have indicated that hydroxyl (·OH) radical may play an important role (7-11). The mechanistic studies of Cr(Vl)-related ·OH radical generation in biochemical systems have shown the reaction of a Cr(V) species with hydrogen peroxide (H20 2 } through a Fenton-like mechanism to be one of the important steps (9-11): Cr(V) + H20 2 - Cr(VI) + ·OH + OH-. (1)In biological systems the Cr(V) species are generated via the reduction of Cr(VI) by a variety of components, such as microsomes (12), mitochondria (13), mitochondrial electron transfer complexes (14), and at least three flavoenzymes (glutathione reductase (GSSG-R),3 lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase) (9, 15, 16). In the case of flavoenzymes, Cr(V) formation is accompanied by the reduction of molecular oxygen ( 0 2 ) to H20 2 • The Cr(V) species then reduces H20 2 to generate •OH radicals and Cr(VI) (16).To understarid the mechanism by which Cr(V}-generated ·OH radicals cause cytotoxicity, Aiyar et al. (8) investigated the reaction of Cr(VI) and H20 2 to generate ·OH radical and its reaction with 2'-deoxyguanine (dG) to form 8-hydroxy-2'-deoxyguanine (8-0HdG}:"

Mar 1, 1992

By T. M. Barczak

The term "resultant load vector" is defined as the representation of the forces applied to a longwall roof support element by strata activity through a single, quantifiable measure of support resistance. The relatively complex kinematics of the shield structure prohibits determination of support resistance simply from the summation of leg forces. In the research reported in this Bureau of Mines study, the mechanics of the shield structure were evaluated, and a technique was developed whereby the resultant shield loading could be determined by instrumenting supports with pressure transducers and strain gauges to measure leg, canopy capsule, and lemniscate link forces. This technique has been laboratory tested in the Bureau's Mine Roof Simulator. Functional relationships among variables were assessed, and confidence intervals were established for prediction of the resultant load vector parameters. Resultant load measurements were taken on five instrumented shields on an active longwall face in Colorado. Results were analyzed and found to be consistent with shield mechanics and anticipated roof behavior. Benefits to be derived from this research, future efforts, and long-range goals are discussed.

Jan 1, 1986

By K. K. Kelley, W. W. Weller

Heat capacity measurements of lead molybdate and lead tungstate were conducted over the temperature range from 51 ° to 298 ° K. The entropies were found to be S298.15 = 39.7 ± 0.5 cal / deg mole for lead molybdate and S298.15 = 40.2 ± 0.5 cal / deg mole for lead tungstate . The entropy values were combined with other pertinent data to obtain the entropies of formation of the two compounds from their constituent elements and oxides .

Jan 1, 1964

By E. J. Schneider

In view of the growing commercial interest In the higher boiling fractions of low-temperature tar, a study of the literature has been undertaken to obtain as many data as possible regarding the properties of possible pure constituents. The following substances have been studied: THREE-ORTHO-XYLENOL (1, 2-DIMETHYL-3-HYDROXYBENZENE) Detection By the isolation of the silver salt of 1, 2-dimethyl-3-phenoxyacetic acid.

Jan 1, 1930

By Eliot J. White

The physical properties and clay mineral content of the major oil-producing formations in the Powder River Basin of Wyoming were determined by analyses of cores from 100 wells. Interrelationships were established among permeability, restored water saturation, clay content, and bulk swelling capacity of the crushed sample and used to estimate the susceptibility of the formations to water damage. The ratio of water permeability to gas permeability (kw/ki) offers a convenient scale for semiquantitatively estimating the water sensitivity of sands. The irreducible water saturation was also found to have a similar relationship to the clay mineral content and the water sensitivity of the sands. The average relation of water permeability to gas permeability is different for each sand, as shown by the curves, and the relative positions of the curves indicate the degree of water sensitivity of each sand from which the susceptibility to water damage may be estimated. How accurately these estimates show formation behavior under field operations will not be known until studies of field performance can be made. The water permeabilities of the Muddy, Minnelusa, and Tensleep sands average about the same as the gas permeabilities, and these sands are classified as insensitive. The water permeabilities of the Sussex and Shannon sands, at the other extreme, are much less than the gas permabilities [when average ki is 30 millidarcys (md), kw is 6.1 md], and these sands are classified as highly water sensitive. The sensitivities of the five other sands are between these extremes.

Jan 1, 1962

By Robert Stefanko

Transients are results of sudden changes which take place in power systems and can be created by the opening and closing of switches and circuit breakers or the occurrence of a fault anywhere in the complex. Transients are of short duration, and the time during which they occur is an extremely small percentage of the total operating time. However, it is during these short periods that the greatest electrical stresses occur, mainly due to excessive currents or voltages. In extreme cases, system parts are damaged, and equipment failure follows. Safety can be further compromised because anomalous voltages can exist at machine frames. For several years, the electric utilities have been well aware of the serious nature of transients on their systems, but problems firmly believed to directly result from these phenomena are just now becoming apparent to the coal mining industry. The situation became discernible after the underground introduction of high voltage distribution systems (along with vacuum circuit breakers) and sensitive solid state electronic apparatus. In order to protect against such transients, knowledge about their characteristics and origin must be obtained.

Jan 1, 1974