Search Documents

By G. L. Oldright

The data in this paper were collected at the Trail smelter of the Consolidated Mining & Smelting Co. of Canada, Limited, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent; George Murray, assistant smelter superintendent; and the staff members given in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the thirteenth of the series on Smelting in the Lead Blast Furnace, and the third of the series on Handling Zinciferous Charges. Tyro other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By D. Harrington

Approximately 2,000 persons are killed annually in the coal mines of the United States. There is no question that this number is at least double and probably treble what it should be and by all means the least excusable of the fatalities are those caused by explosions and fires. Fatalities from explo- sions and fires in coal mines are almost invariably caused by carelessness or negligence. Table 1 indicates that the fiscal year ending June 30, 1931, ras by no means a satisfactory one as regaris either the number of explosions or the number of persons killed by them. This tabulation lists all ignitions to which the attention of the personnel of the safety division was called and in- cludes not only major disasters, but also explosions in which fewer than five were killed, as well as several explosions from which no fatalities resulted. It will be noticed that last year there were 26 explosions in mines in 10 States of the United States, resulting in 217 deaths. In the previous year there were 34 explosions with a death list of 199, and in the year before there were 38 explosions with a death list of 139. Hence, the past fiscal year had distinctly a poorer record of fatalities from mine explosions than either of the two previous years. Of the 26 explosions in the past fiscal year, Pennsylvania had 7, West Virginic 4, New Mexico and Ohio 3 each, Alabama, Oklahoma and Washington 2 each, and California, Illinois and Indiana 1 each; the one in California was in a tunnel being driven for water purposes but giving off explosive gas (methane). In fatalities Ohio had the worst record with 38, Oklahoma came next with 45, then Indiane with 38, and Pennsylvania with 23; although Alabama had 2 ignitions and Washington 1, they caused no fatalities. Utch, Colorado, and Kentucky had no explosions reported by the safety division of the Bureau of Mines during the past fiscal year, but were on the list for the previous year, though in the case of Colorado there were no fatalities. On the other hand, Indiana and New Mexico, neither of rhich was charged with an explosion in the two previous years, were on the list for the past fiscal year; New Mexico had the bad record of three explosions, though fortunately with but a total of eight fatalities. Ohio reported 3 explosions to the safety division of the Bureau of Mines in the past fiscal year, 2 in the pre- vious year, and 3 in the year before that, or 8 in the past three fiscal years with 92 fatalities; all of these eight explosions were in open-light mines.

Dec 1, 1931

By Don Belsher

Work on contract H0272007 is summarized for the period of 1 February 977 to 1 February 1978. The initial evaluation of two potential systems for the location of well casings, voids, and tunnels in coal are described. The pulse measurement equipment used for the evaluation of the antennas selected possible use with a pulse time domain system and an FM-CW system is described. A TEM horn antenna design potentially suitable for use with these systems is given. An operational comparative analysis between various antenna types is presented.

Jan 1, 1978

By Lewis C. Karrick, Martin J. Gavin

"Introduction.The theory of fractional ""education"" of oil from oil shale has been used by several inventors as the basis for the design of retorts for the production of oil from the oil shales of the United States. The term fractional ""education"" gives expression to the rather common belief that when an oil shales is heated it produces light, low-boiling oils as low temperatures, and increasingly heavier, higher-boiling oils as the temperature of retort¬ing rises. The theory evidently had its origin in the fact that crude petroleum may be fractionally distilled, yielding light oils at low distillation temperatures, and heavier oils as the distillation temperature increases is as, gasoline is produced from petroleum at relatively low temperatures, kerosene at higher temperature, and heavier products such as gas-oil and lubricating distillation at still higher temperatures.The writers have examined several oil-shale retorts designed to take advantage of the belief that crude, and in some cases refined, gasoline can be recovered from the shale at low temperatures; kerosene at higher temperat.res, and so on. Such retorts are usually designed to operate continuously and have several vapor-pipes lending from them at differing intervals and passing to separate condensers. Designers of such retorts repeat that the distillate from the low-temperature parts of the retort will be gasoline, and that as the shale passes to zones of increasingly higher temperatures, the vapor lines lending from these zones rill remove increasingly heavier products such as kerosene, gas-oil etc."

Mar 1, 1924

By E. L. Garton

The Bureau of Mines for a number of years has been conducting an investigation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from many oil fields of Oklahoma are given in Bulletin 2913. Analyses of 21 representative crude oils from various producing zones of the Oklahoma City field are given in this report. A close study of the analyses reveals very few differences in the general characteristics and chemical properties of these oils.

Jan 1, 1932

By Donelson A. Robertson

Literature was searched and cases of alleged water well damage were investigated. Occurrence of ground water in Appalachia is primarily in low yield, fractured, water table aquifers. Four test sites were chosen based on geographic and geologic diversity. Test wells were drilled at each site and base line data on water quality, static water level, and drawdown characteristics were obtained before surface mining commenced. Blast induced ground vibrations were measured at the surface by the wells at levels up to 5.44 inches per second maximum resultant particle velocity. Measurements made at the bottom of wells indicated that vibrations were considerably attenuated at depths of 140 to 160 feet. No direct evidence of change in water quality or well performance was produced by blast vibrations, but removal of downslope support by excavation does cause lateral stress relief which permits the water-bearing fractures to become more open. This additional storage capacity causes the static water level to drop and for well-bore permeability to improve. Static water level recovers if sufficient recharge is available and well performance is

Jan 1, 1980

By William K. Cunningham

The investigation described in this report was begun as part of the Bureau of Mines progress to develop acid processes for the extraction of alumina from low-grade bauxite and. clays. A domestic shortage of high-grade bauxite sui table for treatment by the Bayer process became acute as a result of' World War II; an intensive search for a practical acid process using lower-grade alumina-bearing raw materials was therefore warranted. The laboratory development was described in a preceding Bureau of Mines publication wherein the basic theory for the design and erection of a pilot plant maybe found. A 2-ton-per-day continuous pilot plant was constructed and successfully operated at College Park, Md., which demonstrated conclusively the chemical and mechanical feasibility of a solvent purification process for aluminum sulfate. The estimated production cost of $38.64 indicates that under present market conditions the process would not be economically feasible.

Jan 1, 1948

This publication summarizes the in-house and contract research projects programmed for fiscal year 1984 by the Bureau of Mines under its Conservation and Development activity. The document provides a mechanism for interested parties to gain insight into projects of the Bureau's Conservation and Development research program. The objective of the Conservation and Development Program is to provide the technological advances needed to stimulate the mining of domestic deposits containing critical, strategic, and other essential minerals in compliance with existing regulations and at costs sufficiently low to be competitive in world markets. Research efforts are directed toward improving the fundamental understanding of processes and procedures involved in the production of minerals. The overall goals will be accomplished by investigating alternative mining methods to increase domestic production of critical and strategic minerals from low-grade deposits; expanding the technology for the economic and efficient extraction of minerals consistent with cost-effective compliance with environmental regulations; and advancing the technologies needed to insure an adequate supply of coal.

Jan 1, 1984

By K. P. Wang

SIGNIFICANT general developments took place in the Far East during 1964, with far-reaching repercussions on the mineral and industrial economies of individual countries and the region as a whole. Japan, during this, "the Year of the Open Door," ushered in the era of industrial maturity, greater independence in economic policy, and expanded technical assistance to less developed countries. Symbolic of its dynamic economic growth is the fact that Japan out-produced the Federal Republic of Germany in steel during 1964 to take over a third-ranking world position. Mainland China, recovering from the "Leap Forward" debacle, made significant gains in industrial output. Mainland Chinese trade with Japan was on the upswing, and discussions were held between the Chinese and the Soviets for possibly resuming Soviet aid in industrial and mineral development. Meanwhile, United States aid to Taiwan was being phased out because of progress achieved. Rapprochement between South Korea and Japan was imminent late in 1964, a factor which may well affect South Korean mineral development. The Indonesian-Malaysian confrontation created economic difficulties in both countries. The war in Viet-Nam seriously disrupted industrial activities, particularly in the south.

Jan 1, 1966

By J. M. WADSWORTH

The purpose of this bulletin is to describe the methods of constructing and operating representative types of plants in the United States used for removing the light hydrocarbons from petroleum by continuous distillation, such plants being commonly known in the trade as topping or skimming plants. In the discussion of each plant an endeavor has been made to arrange the text similarly in order to facilitate comparison and to emphasize the important features. The various experimental values for the specific and the latent heats of the oils apply approximately to the oil treated. Careful experiments with each oil and its commercial fractions were not justifiable in view of the purpose of this report. It is regretted that limitations for recording data at the different plants made impossible the determination of a heat balance for each, which would have provided an equitable method of comparing efficiencies. The writer has confined himself to a comparison of the relative efficiencies of the distilling apparatus alone by the following method: Effi . f till d tt" _ Heat theoretically required. ciency 0 SIS an se mgs - Heat content of fuel consumed. The plants described are all in California where the topping industry has had its growth accentuated by the character and the use of the oil handled. The scarcity of suitable coal made the adoption of other fuel necessary, and the heavy oil of California supplied the need. To raise the flash point and to dehydrate this oil, various plants have been developed. However, the topping industry is represented in other fields; the Roxana Petroleum Co. of Cushing, Okla., and the Warner-Quinlan Asphalt Co. of New Jersey, are operating Trumble plants, and Texas and Oklahoma operators have been experimenting with different pipe retorts for continuous running. In addition to the reasons for topping cited above, in California topping has other purposes which give the plants practically a universal field in the oil industry. These additional purposes are (1) to remove the lighter constituents of the oil prior to storage for a long period, thus reducing the losses from evaporation, (2) to dehydrate and clean the oil, and (3) in conjunction with a complete refinery, to remove the lighter fractions cheaply and quickly, leaving a residue to be rerun for lubricants, coke, and other products. The reader in studying a plant for possible adaption to his own use should note that local considerations enter into the design and size of a plant. Several questions present themselves, as follows: 1. What type is suitable for the oil? 2. How much money is available for construction? 3. Will the volume of residuum be large enough for heat exchange with the crude? 4. Can the heat content of the vapors be used to reduce the cooling-water requirements? 5. What method will best recover the heat from stack gases? 6. Are the various pieces of apparatus adequate in size and best adapted to their purpose? 7. Is every possible provision made for the recovery of waste heat? 8. What products will be made, and what volume of each? 9. Is there provision for the recovery of light vapors? 10. Will the saving of fuel justify the capital and maintenance charges on the regenerative apparatus contemplated? It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished. The reader will find fuel economy and heat recovery emphasized throughout the descriptions. The conservation of the available petroleum supply is of the utmost importance, and the Bureau of Mines presents this paper to encourage the hearty cooperation of operators to that end. The Baume gravity scale used throughout the report is that of Tagliabue with a modulus of 141.5 for conversion to specific gravity.

Jan 1, 1919

By Richard S. Fowkes

Advanced technology, including automation and computerized information systems, is being adopted in mining at an ever-increasing rate to improve safety and productivity and to decrease overall costs. This U.S. Bureau of Mines report focuses on the human factors issues related to advanced technology. Among the significant facts discovered were the following: Experts studying tile design adoption, and implementation of new technology have stated repeatedly that human factors specialists should be involved from the early planning stages, through design and fabrication, and up to and during production, since human factors has been consistently identified as the biggest obstacle to the efficient utilization of new technology. Also, middle management is generally the greatest obstacle to the adoption of advanced technology, this technology can give rise to worker alienation, boredom, stress, job insecurity, and a sense of isolation; training most of the present work force is more cost effective than hiring new workers; workers are willing to accept new technology if they are given a voice in its implementation; the social and the technical systems should be jointly optimized; and with the intro¬duction of advanced technology, the cognitive or mental, rather than the physical, aspects of human-machine interaction must be emphasized.

Jan 1, 1994

By G. H. Gronhovd

This is the final report on a research program to develop a pilot plant gasifier for slagging gasification of lignite at high pressures and to obtain process data under various operating conditions. An operable pilot plant was developed, and the test results show that lignite is well suited for the process. Tests were run at pressures from 80 to 400 psig, and the results indicated that pressure had little effect on gas composition or the material requirements per unit gas produced. Gas production rates as high as 26,000 scfh/sq ft of reactor area were obtained at 300 psig, but limitations on auxiliary equipment prevented full-capacity operation at 400 prig. In several tests lignite having a 37-percent moisture content and 2,500° F ash-fusion temperature was successfully gasified. Refractory materials were found to have a short life in contact with high-temperature slag, and a water-cooled taphole was developed. Exploratory tests with coking coal were unsuccessful.

Jan 1, 1970

By Robert L. Kranz

The U.S. Bureau of Mines (USBM) has been monitoring and studying seismic activity associated with mining in the Coeur d'Alene silver district of northern Idaho. New statistical methods of studying the stope-scale (1-to l00-m) seismicity at one Idaho silver mine are used in this report (part 1) and its companion (part 2). This report deals with methodology and its limitations. The recent concept of fractals and their seismological use is discussed and applied to mining-induced seismicity. Three types of fractal studies are addressed: spatial analyses (including temporal changes of spatial patterns), temporal analyses, and size analyses. Other statistical measures of mine seismicity are also addressed: event mean location, inter-event distance distribution skewness, temporal coefficient of variation, nearest neighbor and next event statistics, and event location planarity patterns. Each of the methodologies discussed (fractal and nonfractal) is presented using sample data from two stopes in the mine. It is shown that stope-scale, mining-associated microseismicity has a fractal nature. The usefulness of demonstrating fractality (scale invariance) for predictive or descriptive purposes depends on recognition of the factors affecting the calculation of fractal dimensions. Several methodological traps are illustrated that can lead to an incorrect conclusion.

Jan 1, 2010

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By R. E. Siemens, Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites . The process consists of four mmaajjoorr steps : ( 1 ) reduction roast , ( 2 ) ammoniacal leach , ( 3 ) solvent extraction , and ( 4 ) electrowinning . Several solid - liquid separation steps are required that affect the economics of the overall process . In this study , two techniques for solid - liquid separation , centrifugation and thickening , were investigated . This report presents the results of ( 1 ) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and ( 2 ) an economic study of the two techniques , based on the requirements of a commercial - size ( 5,000 - tpd ) laterite processing plant . Sizing and other equipment - related recommendations , based on data from the Bureau's studies , were obtained from commercial manufacturers . The costs of thickening and centrifugation , including all the unit operations affected , were determined by the Bureau's process evaluation group . The total operating costs for separation using the two techniques ( including depreciation on the capital cost of equipment ) were found to be quite close : $ 17.26 per ton of laterite for centrifugation and $ 18.15 per ton of laterite for thickening . For centrifugal separation , the greatest cost was found to be the initial capital cost for the separation equipment ; using thickeners , the greatest cost was for reagent recovery .

Jan 1, 1983

By Lawrence G. Houk

In modern warfare mica is truly indispensable. The coordination of combatant units necessitates maintenance of intricate communications equipment, in the construction of which high-grade sheet mica is essential. Scrap, ground, and the poorer qualities of block mica, which are less essential to the military program, are not considered in this paper. Furthermore, as the paper is designed primarily to assist mica miners, mica derivatives such as splittings and films are also excluded from discussion. The paper therefore relates solely to block mica of strategic quality.

Jan 1, 1942

By G. B. Shea

In the search for possible future sources of petroleum products, the recovery and utilization of bitumens from the large outcropping deposits of bituminous sandstones in the United States have been under study by the Bureau of Mines for the past several years. The results of laboratory research in the adaptation of the hot-water separation process to recovery of bitumen from bituminous sandstones were reported in an earlier publication, on the Edna deposits near San Luis Obispo, Calif. This publication included analytical data on the cracked products and asphalts obtained from the extracted bitumen and on the cracking and distillation of the bitumen. Comparable hot-water separation tests have been run in the San Francisco, Calif., laboratory of the Bureau of Mines on quarry samples from the large deposits of bituminous sandstones near Vernal and Sunnyside, Utah. The bitumens were isolated from the extracts of the separation plant and analyzed at the Petroleum and Oil-Shale Experiment Station of the Bureau of Mines, Laramie, Wyo. Part I of this report summarizes the general characteristics of the Vernal and Sunnyside deposits and discusses the hot-water separation process as applied to those bituminous sandstones and the results obtained. The separation tests showed that these bituminous sandstones also respond to treatment by the hotwater method of separation. The bitumen in the Vernal sandstone was extracted more readily by the action of hot water than was the Edna bitumen, which greatly simplified plant operation. The Vernal sandstone contains no water-soluble iron compounds, such as were found in the Edna sandstone, and, therefore, required no preliminary water washing. Recovery of bitumen from the Vernal sandstone was about 96 percent.

Jan 1, 1952

Southeast Alaska's mining industry has come to life after nearly 50 years of relative dormancy. Commencement of operations of the Greens Creek Mine in 1989 marked a turning point in the industry as the first large scale mining operation in the region since closure of the Alaska-Juneau Mine in 1944. The Greens Creek Mine is now the nation's largest silver producer. Other large scale mining projects are now on the drawing board, including development of the Kensington Mine and reopening the Alaska-Juneau Mine, which could become North America's largest underground gold mine. The region's mining industry includes more than these large scale projects, however. For example, a significant level of mineral exploration occurs each summer in Southeast Alaska. In addition, mining operations in British Columbia and Yukon Territory are generating jobs and income in Southeast Alaska.

Jan 1, 1992

By G. L. Oldright

This paper is the thirteenth of the series on Smelting in the Lead Blast furnace, and the third of the series on Handling Zinciferous Charges. Two other papers have been written on the Rate of Descent of the Stock Column, and Formation of Accretions. These are Reports of Investigations 2963 and 3094, for the Tooele plant and the Bunker Hill plant, respectively.

Jan 1, 1934

By G. T. Fisher

The material requirements of carbide cutting tools for machining steel and cast iron are dependent on WC bonded with Co, with additions of TaCand TiC. The Bureau of Mines is conducting research to devise substi-tute materials, based on Ni-alloy-bonded TiC, for C-5-grade cutting tool applications. This substitution would result in less dependence on foreign sources for Co, Ta, and W, and use of lower cost materials. In this preliminary study, the Bureau investigated the effects of composition and processing variables on the transverse rupture strength and hardness of Ni-alloy-bonded TiC to identify compositions that exhibit promising mechanical properties. Further systematic modification of these compositions by soild-solution strengthening additions would subsequently be evaluated to obtain cutting tool materials with requisite properties and performance for C-5 applications. Compositions for evaluation were prepared by a powder metallurgy method of cold-pressing and liquid-phase sintering. Complementary analysis of compositions included chemical analysis, X-ray diffraction, energy-dispersive X-ray spectro-scopy, and density measurements. Based on results of this investigation, promising compositions were determined to be 59.37TiC-25Ni-5Mo-lO.63Mo2C, 59.68TiC-25Ni-3.33Mo-1.77Mo2C-6.67W-3.55WC, and 59.35TiC-25Ni-l.67Mo-3.54Mo2C-3.33W-7.1WC.

Jan 1, 1987