Search Documents

By B. N. Hira

A multistoreyed residential complex was at the penultimate stage of construction by ONGC at Nazira, Assam. The site was situated at high earthquake zone. The subsoil was very weak and contained soft to medium clay with water table almost at the ground level. The bearing capacity of soil was quite poor particularly with predicted settlement beyond permissible limit. In this situation, the conventional shallow and deep foundations were found uneconomical and ground improvement with granular piles was considered as the viable solution. ONGC approached the Central Building Research Institute with the request to design granular piles along with R.C.C. foundation and other suitable cost effective measures. CBRI collected relevant geotechnical informations and supplimented the data by conducting field tests at site and laboratory tests at Roorkee. Rational design of 30 cm dia. and 5.00 meter deep granular piles were suggested with isolated and combined RCC footings over the reinforced soil. In addition to several structural and geotechnical advantages, the granular pile foundation provided considerable economy in the cost of construction. The paper presents the salient geotechnical and structural informations of the challenging project and provides the design details of the innovative granular pile-system. It also furnishes the design approach of the RC footings and other elements of the foundation.

Jan 1, 1996

By Charles H. Dowding

Whenever piling vibrations are significant, construction activities associated with pile driving and/or excavation can produce permanent displacement. These permanent displacements are more detrimental to structural performance than the hair sized, cosmetic, plaster cracks that might be produced by slightly exceeding reasonable vibration controls. Case studies are presented which demonstrate the relative importance of permanent displacements compared to directly produced transient vibration displacement within a horizontal distance of one pile length. Special attention is paid to settlements produced by densification of liquefiable sands. SOURCES OF TRANSIENT AND PERMANENT DEFORMATION DURING CONSTRUCTION Confusion over multiple sources of facility deformation caused by adjacent construction complicates the discussion of the relative importance of vibration induced cracking. None of the recent scientific investigations of vibration induced cracking (Siskind et el, 1980), involved deformation other than that produced by ground vibration from rock blasting. Thus these studies carry the implicit assumption that no ground deformation occurred other than that produced by the transient vibration. In other words there is no permanent deformation other than that which is typical of the older residential structures investigated.

Jan 1, 1991

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

By Thoedtida Thipparat

The diaphragm walls and barrettes are very important to the constructions of multi-storeyed buildings, elevated expressways, subway railway stations, etc. Uncertainties particularly increase in accordance with the construction progress. Overcoming uncertainties influences the construction goals including achievement of time. This paper is aimed at proposing an uncertainty assessment and delay evaluation model to assess uncertainties and evaluate delay resulting from those uncertainties. Neurofuzzy systems (NFSs) for assessing uncertainties and evaluating delays are developed. Artificial neural networks (ANNs) have ability for learning from the past data and generalizing outputs for the next applications which are provided for fuzzy logic systems (FLSs). FLSs have ability for exploiting the tolerance of imprecision and uncertainty. FLSs provide the reasoning to the ANNs. Uncertainties affecting each operation were assessed and delays were evaluated by following steps of the proposed model. The uncertainty assessment and delay evaluation approach was applied to a diaphragm wall and barrette construction to demonstrate how to implement the proposed model. The results of the test case application were used for handling delay at all operations regarding the corresponding uncertainties.

Jan 1, 2006

By Jogeshwar P. Singh, Aser I. Abbas, Mohamed Ashour

The presented methodology predicts the pile head response (i.e. pile head load - displacement curve) and develops the load transfer (t-z) curve of piles in sandy soils under tension forces based on soil/pile properties and soil-pile interaction. The proposed approach improves the prediction of the t-z curve in sandy soils compared to current practice. The method employs a nonlinear soil constitutive model to calculate the mobilized shear stress/strain in soil at the soil-pile interface induced by pile upward displacement. The approach accounts for the influence of the pile slenderness ratio on the predicted t-z curve and is validated through comparisons with measured pile head response and t-z curves from full-scale pile load tests. INTRODUCTION Piles may be subjected to axial uplift forces due to either static loading or cyclic loading. The majority of methods are only concerned with the pile ultimate tensile capacity. However, the mobilized pile stiffness (i.e., pile-head load-displacement relationship) is essential to determine the interaction between the foundation and the superstructure and consequently the performance of the whole structure. Methods that assess the pile ultimate tensile capacity usually assume the failure surface at the soil-pile interface and estimate the local side shear resistance using a lateral earth pressure approach. The Naval Facilities Engineering Command (NAVFAC 1986) and the US Army Corps of Engineers (USACE 1991) employed Eq. 1 to assess the ultimate shear stress (τ) developed at the soil-pile interface.

Jan 1, 2018

By R. Stenne

This paper deals with a complementary soil investigation which being part of the contract helped understand the behavior of a softened clay and adjusted the design of a retaining structure accordingly. The investigated softened clay proved to have lost its original strength but had maintained some characteristics of its stress history and in particular high horizontal stress. Pressuremeter tests and flat dilatometer tests were of interest to estimate the at rest earth pressure. A design consisting of a T-shaped slurry wall in conjunction with transverse walls was the most effective solution to cope with high active pressures and low passive pressures.

Jan 1, 2000

By C. J. Kirkland

For two thousand years and more, we insular Britons have been grateful for the existence of the narrow strip of water that separates us from mainland Europe. It has given us a sense of security against invaders, though it has been breached many times. The first recorded serious consideration of a fixed crossing of the English Channel was in around 1802, when it was suggested to Napoleon I. The motive was not entirely peaceable and the British Navy, who saw themselves as defenders of our shores, were decidedly unenthusiastic A whole series of imaginative schemes were proposed in the course of the nineteenth century, embracing viaducts, immersed tubes, artificial islands as resting places for the horses which were to draw carriages, as well as mechanically bored tunnels. The first Channel Tunnel Company was formed in 1872, and an application for permission to construct a tunnel was made to the British parliament. A Colonel Beaumont, of the Corps of Royal Engineers designed and constructed a machine which, in around 1882, bored over a mile of tunnel out to sea from Britain which exists to this day.

Jan 1, 1991

By Christopher J. Pacitto

This paper presents a case history of an engineered, monitored, and tested program that provided an effective and satisfactory basis for the completion of pile foundations for Twin Dolphins 1 at La Peninsula Condominiums located in the Isles of Capri in southwest Florida, U.S.A. An 8-story building (withl-story parking underneath) along with recreational facilities (such as a swimming pool and tennis courts) had been planned for final construction. Following an evaluation of various foundation alternatives, a precast prestressed concrete (PPC) pile-supported system was selected. The building foundations were designed for pile capacities of 445kN (50 tons) and 890kN (100 tons) in compression and 133kN (15 tons) in uplift. A test pile program was performed to provide site-specific pile driving data, verify design assumptions, determine production pile lengths, and evaluate pile driving criteria. A total of 24, 356 mm (14-in.) square, 19.8 m (65 ft) PPC concrete piles were driven and dynamically load tested utilizing a Pile Driving Analyzer (PDA) within the building limits. Dynamic monitoring during probe pile installation and restriking was performed to estimate the ultimate capacity of the piles and to evaluate driving stresses during installation. CAPWAP analyses were preformed on PDA data to better estimate pile capacity, resistance distribution, and predict pile freeze (increase in pile resistance with time) and thus optimized the production pile lengths. Upon completion of probe pile installation, 12 of the probe piles were tested using the Pile Echo Tester (PET) function of the Pile Integrity Sonic Analyzer (PISA). PET testing was performed to evaluate the integrity of piles which had exhibited high driving stresses during PDA testing. Information gathered during the probe pile driving program was effectively utilized as part of the overall quality control program to install a total of 539 PPC piles (including 24 probe piles) within the building limits at the project site to depths ranging from 9.1 to 19.8 m (30 to 65 ft) below the existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared very well with the capacities from the CAPWAP analysis for probe piles. Use of geotechnical instrumentation and PDA assisted technology enabled each foundation support element to be constructed to its optimum capacity and at optimum cost. Furthermore, by using PDA the consultant was able to quantify a difficult to measure geotechnical phenomenon termed "pile freeze" which eliminated costly overdriving and unnecessary splicing of piles.

Jan 1, 2002

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibration limits for buildings with respect to ground vibrations from pile driving published in international standards are reviewed. At first, relevant vibration parameters are defined and the evaluation of vibration records is described. The sensitivity of structures to different vibration parameters (displacement, velocity and acceleration) is discussed. Most vibration standards relate to blasting activities, the dynamic characteristics of which can be significantly different to those from construction activities and in particular, pile driving. Several vibration standards are reviewed. The Swedish vibration standard is described in detail, as it is the only one accounting for several important factors, such as ground conditions, building material, and type of building foundation. Many standards limit the guidance to values based on the dominant vibration frequency and a wide scatter of frequency-dependent vibration limits exists. It is difficult to compare limiting values of ground vibrations proposed in different standards.1. INTRODUCTIONFor poor ground conditions, placing structures on piles is the most common foundation solution, while sheet piles are widely used to support deep excavations. Piles and sheet piles must often be installed in the close vicinity to buildings, structures or installations in the ground, which can be affected by ground movements and vibrations, (Massarsch and Fellenius, 2014). In many areas, environmental concerns with respect to noise and ground vibrations can restrict or even prohibit driving of piles or sheet piles or reduce the efficiency of installation. The design engineer must prescribe – often at an early stage of a project — the permissible levels of ground vibrations in order to minimize the potential risk of building damage. When seeking guidance from the literature, little or practically no applicable information can be found on how to assess permissible levels of ground vibrations."

Jan 1, 2014

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By D. Arentsen

Changing environmental laws, new operating requirements and the increasing accuracy with which the bearing capacity of driven piles can be calculated have all led to the development of hydraulic piling hammers, some very primitive, others very advanced. Users find it difficult to decide which model is the most suitable, because the specifications are neither uniform nor unamiguous. There are no standard specifications and, moreover, the majority of hammers are suitable only for a limited range of applications. For the user, however, it is important to choose a hammer which will meet future as well as current requirements and will not quickly become obsolete or be unsuitable for a particular job.

Jan 1, 1987

By T. Jason Hardell

The Victory Bridge project was contracted by the New Jersey Department of Transportation. The project included the construction of two 4000-ft precast segmental concrete bridges to replace the existing Victory Bridge that was built in the 1920's. The existing bridge was a swing span bridge that was in desperate need of replacement. The project was considered high priority due to the large maintenance costs to keep the swing span operating over the busy navigational channel. In March of 2003 construction began on the first bridge and by April of 2005 all of the segments were set for the second bridge. On September 5 of 2005 the second bridge was open to traffic. The total cost of the project was $110-million. The two new bridges required the construction of 24-eight foot and 32-six foot diameter-drilled shafts with rock sockets. All of the shafts were constructed in the tidal Raritan River working from barges. What will follow is a description of the construction techniques that were used to build these drilled shafts, the anticipated and unanticipated challenges that were encountered during the project, and the lessons learned.

Jan 1, 2005

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By Patrick J. Hannigan, Geir Veslegard, Frank Rausche, Rozbeh B. Moghaddam

A common type of deep foundation used in Norway to support bridge structures is the drilled pipe piles (piles) filled with concrete reinforcement after installation. The standard installation practice is the use of down-hole hammers. Complex geology and difficult subsoil conditions in Norway causes a high variability of soil and rock layers which in turn make for differences between actual subsurface conditions and those expected from geotechnical exploratory borings. This situation is strongly noted when the foundations are not fully socketed, and the rock layer is sloped. In this particular case, special testing procedures are required to assess the drilled pile base material and evaluate the rock-socket to ensure full contact between the foundation base and the rock surface. The local standard practice to verify the latter condition, consists of coring and visually evaluating the material recovered at the bottom of the drilled pile. This paper presents a case where the coring and visual inspection were not possible and alternatively the geological material encountered at the base of the deep foundations was evaluated using force-displacement measurements. Two 1016-mm (40in) diameter open-end drilled piles identified as P02-04 and P02-05 were tested and evaluated using in-situ force-displacement data prior to filling the piles with concrete. Test results showed an average displacement of 7mm (0.28in) corresponding to 35MPa (5.1ksi) stress level for P02-04, and 7.2mm (0.28in) corresponding to a stress level of 38MPa (5.5ksi). Based on testing results, both drilled piles were within the established material assessment criterion presented by the local authorities. INTRODUCTION This paper presents a case study in Norway where the material encountered at the base of an open- end drilled pipe pile (pile) was evaluated using force-displacement data. In the deep foundation industry in Norway, it is a common practice to install piles to support transportation structures. Once the piles reach the embedment elevation, and the pile base is assessed, these are filled with concrete. In projects where sloping rock is the supporting layer, and all nominal loads are supported by the pile base resistance, assessing the material encountered at the pile base to ensure full contact with the rock becomes critical. The local practice to make this assessment consists of the use of weighted tape, coring, or inspection cameras. However, similar to any other testing and evaluation methods, these come with their own limitations. The variability associated with the use of the weighted tape, accessibility for the coring equipment to complete a coring process, or the conditions at the foundation base such as murky water or thick drilling fluids could significantly impact the photo or video quality taken at the pile base. In such conditions, it is important to consider alternate testing methods to evaluate the material at the foundation base.

Jan 1, 2018

By J. J. Beresford

The primary function of a support slurry is to provide stability during excavation. Today foundation structures can be designed around the additional friction afforded by the absence of the filter cake attributable to the use of polymeric fluids as support slurries. These fluids use pseudoplastic fluid viscosity to advantage over the fragile thixotropic gel structures of bentonite. Many of today's polymeric fluids are environmentally acceptable for disposal directly to municipal sewers.

Jan 1, 1989

By S. Merjan

Three papers were presented for discussion at the conference: 1) Instrumented driven steel tube piles at Canary Wharf; author: A. R. Gaba, United Kingdom. The author described the Canary Wharf development in the London Docklands, and in particular, the decision to build over the water by driving open-ended steel piles 25m in length into the sands below the soft estuarine deposits. The tubes were then filled with concrete above the sand plug (usually 17m below pile head). Three trial piles were instrumented with: a) resistance strain guages on the inside of the tubes; b) vibrating wire guages on the re­inforcement of the concrete. The trial piles showed elastic behaviour in five cycles of lateral loading, while the verticle load tests showed a definite bi-linear load-settlement behaviour. The initial stiff portion was a result of frictional staff resistance, both inside and outside the tube, with the soil at the base contributing at higher settlements. Loads were taken to three times working load, with no imminent signs of failure.

Jan 1, 1991

Jan 1, 1985

Jan 1, 1995

By Timothy C. Siegel

This report presents the results of a synthesis on the design and analysis of ground improvement for liquefaction mitigation. The synthesis included an industry survey concerning the practice of ground improvement for liquefaction mitigation. Participation in the survey was solicited by advertisements in several trade magazines and by e-mail for the DFI membership. The survey participants numbered 150. Their professional roles include consulting engineers, specialty contractors, design engineers, government engineers, and academicians. They represent a variety of geographical areas including North/Central/South America, United Kingdom, Middle East, Caribbean, Hawaii, Japan, India, Egypt, France, Australia and New Zealand. Upon completion of the survey, several professionals in the field of liquefaction and ground improvement were interviewed for them to elaborate on the survey results. The interviews are included in the Appendix of this report. Financial support for the project was provided by DFI and Dan Brown and Associates PC. The concept of the liquefaction mitigation synthesis was developed by DFI?s Ground Improvement Committee in recognition that: (a) The results of recent research and post-earthquake reconnaissance have challenged previously longheld beliefs about liquefaction and associated mitigation techniques, and; (b) The DFI membership and the engineering/construction industry are interested to know if and how engineers and designers are subsequently adjusting their practice in consideration of recent research and post-earthquake reconnaissance. For more detailed information on recent research and post-earthquake reconnaissance, presentations are available from the State-of-the-Art Forum: Liquefaction Consequences and Mitigation that was held in St. Louis in 2012. A commentary of the state-of-practice in ground improvement for liquefaction mitigation (prepared by DFI?s Ground Improvement Committee) is included in this issue of the DFI Journal. The author would like to thank the participants of the survey and especially Mr. Mike Jeffries, Dr. Les Youd, and Dr. Ikuo Towhata for their willingness to share their expertise in interviews. The author also acknowledges Mary Ellen Bruce of DFI, Billy Camp of S&ME, Inc., and Marty Taube of DGI Menard (and Chair of DFI?s Ground Improvement Committee) for their signifi cant contributions.

Aug 1, 2013