Search Documents

By J. Fournier

A novel sol ? gel (SG) synthesis procedure utilizing varying ratios of glycine and ethylene glycol to total metal cations has been developed to create high purity nanometer sized La0.65Sr3.5MnO3 powders. X-ray powder diffraction (XRD), transmission and scanning electron microscopy (TEM, SEM), and dynamic light scattering (DLS) have confirmed that the crystallite sizes of such powders are ~ 20 nm, and the aggregate particle sizes vary between 100 to 300 nm. Mixing varying weight percents of SG LSM powders with commercially available Praxair LSM in a composite LSM/YSZ functionally graded cathode has been shown, through the use of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), to exhibit enhanced oxygen reduction kinetics vs. at conventional cathode materials.

Jan 1, 2005

By M. J. Hadianfard

The effect of holding at temperature on fatigue life of a 10 vol% particulate SiC reinforced Titanium alloy has been investigated. The influence of holding time at 600°C on fatigue of this material has been studied by using tension-compression tests, scanning electron microscope and image analysis. The specimens were heated to 600°C by using a controlled atmosphere furnace; hold at this temperature for time ranging from 0 to 100 hours, and then fatigue tested at room temperature under controlled constant plastic strain. The number of cycle to failure found to decrease with increasing of the holding time. In addition the fracture mechanism and number of debonded particles has been significantly influenced by holding time at 600°C.

Jan 1, 2004

By J. Fox, K. Kocsis

"Planning for sustainable cooling potential requires protected space to successfully maintain chilled propylene glycol in storage until needed. Stored propylene glycol should be judiciously cared for, safely kept from the ill effects of heat, in order to remain useful for bulk air cooling. Minimizing the chilled temperature of the propylene glycol reservoir tanks means that atmospheric conditions will be monitored closely during the chilling phase. Storage facilities would maintain restricted airflow while minimizing possibilities for heat transfer during the storage phase. Sustainable cooling systems could reduce or eliminate the need for mechanical cooling if installed with favorable conditions. Storing the cooling potential from the winter months is what this new design is all about.INTRODUCTIONIn most subsurface, bulk air-cooling methods, the main source of potential cooling energy comes from cold-water applications. This paper investigates the practical use of harvested, chilled propylene glycol as the source of cooling potential. Propylene glycol is chosen as the cooling storage liquid refrigerant since its chemical make-up is intrinsically safe to fresh water supplies and will not harm underground workers should a leak occur in the closed cooling circuit. Harvesting the cold of winter is a meaningless endeavor without proper thermal planning for the storage of the cooling potential in cold refrigerant.PROPYLENE GLYCOL STORAGE RESERVOIRA new design for a closed refrigerant bulk air cooling system employing propylene glycol as the refrigerant is presented as the main design topic of this paper. Given that a deep and hot mine will need to be considered safe and productive, a cost-effective cooling system is desired in order for the mining operation to be considered sustainable. For underground mines at northern latitudes, cooling applied to fresh air is only required 3 to 4 months of the year. During winter, ambient atmospheric conditions can be harnessed and stored for use at a later time.The basis of this sustainable design uses very cold ambient air that is circulated around galvanized steel refrigerant reservoir tanks. The propylene glycol reservoir tanks are arranged in a concrete walled pit, or tank farm, excavated in bedrock. During the coldest months, the tank farm will be exposed to the open air. As the seasons change the tank farm will be covered with insulation to maintain the maximum cooling potential for use during the warmest months of the year."

Jan 1, 2019

By J. M. Turnbull

THE primary objective of the young graduate, after the war, will be to obtain a suitable position within the Industry, with adequate pay and opportunity to advance. The positions available to meet this demand will depend on the magnitude and organization of the industry. The size of the mining industry, in particular, will depend on a number of factors, including depletion; new discoveries of mineral deposits; beneficiation of new kinds of mineral deposits, based on research; technical improvements, also based on research, enabling the mining of lower grade deposits; and complex social factors. The organization of the industry will depend on its control and management, which may be greatly affected by social conditions and changes, and may include a wider or a narrower use of technical services. The corresponding training or qualifications of graduates, to meet these conditions, calls for a consideration of educational requirements and facilities in relation to the conditions that are likely to occur. Some forecast of the probable future of the Industry, after the war, based on consideration of. the above factors, is necessary as a basis of discussion, since the graduate must find his place in the industry of that time, and find his work in maintaining and improving it, within the existent social framework. Social factors are pressing and? important at present and their future impact is uncertain. In considering these, a few quotations and extracts may be in order. "A new economic order, based on free access to the sources of raw materials, means free use of the world's wealth by all civilized nations" (The Pope. Also advocated by Churchill and Roosevelt in the Atlantic Charter). "Every citizen should have a voice in the conduct of business or industry which is ?carried on by means of his labour" (Archbishop of Canterbury).

Jan 1, 1943

By Lou Covello

Bow Valley Industries Limited i conducting an on-going exploration program for gold in Archean, turbidite-hosted iron formations near the Lupin mine on Contwoyto Lake, orthwe t Territorie . Exploration philosophy and practice are modelled on the Lupin deposit where 70% of the gold occurs within laminated pyrrhotitechert. sulphide facie iron formation. Thi i intimately associated with barren to low-grade silicate facie iron formation which i enclosed by predominantly argillaceou meta ediment . This type of mineralization i amenable to exploration through an integrated program of geological and geophy ical surveying, consisting of the following: i) Geological urvey both regional and local to outline area of turbidites and a ociated iron formation. Structural and tratigraphic trends documented during this phase are useful in determining eventual grid configurations. Grids are then mapped and ampled at 1:2000 cale. ii) Magnetometer and gradiometer urvey at the ame scale define strongly magnetic diabase dyke and erratically magnetic portions of iron formation. iii) VLF-EM survey are u eful in outlining conductive trend invariably as ociated with sulphidic or graphitic phase of iron formation. iv) Geological updating and ampling of iron fom1ation based on the geophysical su rveys. This is necessary for the production of a final geologic map and a an adjunct to drill target election. In problematic instances self-potential urveys have documented the pre ence of non-conductive sulphide accumulations, and horizontal loop EM surveys have been used to determine conductor geometry and quality. Target selection is based on a synthesis of the information from all of the above surveys with the results of no single survey being critical to drill decisions. The program is designed to provide first-pass, detailed , cost-effective ground coverage of large areas of highly prospective geology.

Jan 1, 1986

By Michel Noël

This paper presents a partial compilation of adopted measures of waste rock dump closures at mine sites located in Canada and Alaska, where the climate includes cold winters. The paper also presents the selection process that was followed for some of those mine sites. Mining operations usually generate waste rock that can sometimes result in very large quantities. Additionally, the nature of the ore body and the host rock will often introduce environmental impacts. These impacts need to be managed not only during the operations but also in the long term. Mine closure plans consequently have to address the long term issues that sometimes require perpetual treatment. Closure planning often involves the evaluation of risks associated with environmental and financial liabilities. It needs to consider the science, some common definition of objectives, and there will be a need to manage resources and schedules. Closure planning is essentially an exercise in constrained decision making. A performance and risk based ranking matrix is often developed during this selection process to identify the preferred option(s). The case studies presented in this paper provides a few examples. The level of knowledge on acid rock drainage from waste rock dumps has increased considerably over the past decades. It did not necessarily increase the level of complexity of the adopted closure methods, as the selected closure methods are often kept simple. A common approach consists of stabilising the slopes of the waste rock dumps material by resloping and then covering the waste rock with a growth media to support vegetation. Such covers prevent direct contact of animals with the waste rock material, minimise erosion and reduce infiltration to various degrees. The inclusion of water treatment is obviously dependent on the water quality being released.

Nov 1, 2008

By W. T. Thompson, S. Durham, K. M. Jaansalu

The role of platinum on the relative stability of gamma - gamma prime equilibrium is only qualitatively known, and may bear upon the stability of a superalloy under a protective coating. The binary phase diagrams Ni-Pt and Al-Pt, and the Ni-rich corner of the Ni-Al-Pt ternary, are reviewed and simple self-consistent thermodynamic models are derived. These thermodynamic models are incorporated into a database used to predict the gamma-gamma prime equilibrium for single crystal superalloys. In small concentrations, platinum is predicted to increase the temperature stability, but not the proportion, of the gamma prime phase over the gamma phase in third generation alloys such as CMSX-10. Another effect of platinum addition is to significantly lower the solidus temperature. These findings are compared to experimental data in the literature.

Jan 1, 2004

By S. Xu, A. Ramesh, F El-dabbagh, Z. Fang, A. Sobhy, J. A. Kozinski

Waste remediation is a goal that will be driven forward by economic conditions. As the cost of waste disposal increases, new methods of waste reduction will become economically attractive, and will be implemented. It is difficult to imagine, however, a time when there will be no waste generation. For the foreseeable future, despite effective reduction practices, there will still be hundreds of millions of tons of waste that must be destroyed or controlled to protect the public health and the sanctity of the environment. To remain faithful to environmental covenants, the mineral and metallurgical industries will face these new challenges. This paper discusses novel waste remediation approaches and techniques focusing on hazardous wastes and thermal remediation. Aspects concerning technological and environmental importance are examined. Solutions for neutralization of environmentally hazardous compounds are proposed.

Jan 1, 2004

By D. Brossman

"The virtue of spray drying is that it is a drying method, and so far the only one by which it is possible in one operation to divide a mineral concentrate into its basic primary particles.,In so doing, each particle gets the same treatment and the result is a dry concentrate more homogeneous than any other known concentrate drying process. This is particularly good for a flash furnace requiring a bone dry finely divided feed. The spray dryer also features a very short residence time and due to the very quick operation the solids are kept cool thus preventing any risk of fire or explosions on these pyrophoric materials.There are many spray dryers now in operation in the mining industry and one of the latest applications is in South Africa where a spray dryer is treating a copper-nickel platinum concentrate which is, after drying, fed toan electric arc furnace. Experience has shown that the concentrate should contain 4% moisture for the furnace, and this is achieved by drying the concentrate bone dry and then back-mixing with thickener underflow pulp to provide an extremely homogeneous feed to the smelter. As mentioned before, mixing with pulp would be more of an advantage because we would not be evaporating water which would have to be added again afterwards.One of the first spray dryers to go in was at Western Mining Corporation in Kambalda in Western Australia. (A series of slides was then shown)."

Jan 1, 1972

By G. Langlands

"R. Tenbergen Is this flotation machine suitable in the flotation ofInco ball mill discharges where we have a coarse feed at 60% solids?Reply Experience has shown that there is not a significant increase in the wear life of these machines when handling coarse material (8 mesh) at 60% solids. A common practice in Europe is shut down on the week-ends.The material is allowed to settle and on start-up an injectic of air for 15 seconds is sufficient prior to start-up. At,mining we put our unit in the middle of a bank of 44 cells and in order to ensure severe sanding we shut the aker cell down while the remaining cells kept running. After 20-25 seconds of air the cell started without trouble.P. Mahant Is there a build-up inside the impellor shaft housing? Falconbrige Ltd.Reply There is no sand build-up but rather a scale build-up which due to a flexing action frees itself periodically. Part of the design of the machine permits a water injection into the shaft housing to free any build-up. This is done in Europe during the week-end shut down."

Jan 1, 1984

By A. Hasselbring

Sub-Level stoping was used in this country at least as early as 1912, at the Magpie mine in Michipicoten. The fundamental principles of the system are the same wherever it is used, but modifications have been adopted in the Michigan iron mines and in several Canadian mines. It is a system whereby a suitable body of ore may be developed quickly and worked cheaply, with a low initial expense, and by miners of quite ordinary ability. The basic method, described in the following pages, may be modified to meet conditions where one or more factors are not in accord with normal sub-level stoping requirements. In suitable ground, sub-level stoping is probably the most satisfactory method yet devised for underground hard-rock mining. It is so simple, straightforward, and safe that no special training of a crew is necessary. Any miner capable of drifting and raising can carry on the work necessary for sub-level stoping after the shaft has been sunk. The method is suitable, however, only for reasonably wide ore-bodies, the minimum width of ore to which it can be economically applied being somewhere in the neighbour-hood of thirty feet. The development programme is simple. Assuming, for purposes of illuslustration, an ideal ore-body, two thousand feet long, dipping nearly vertical, and varying in width from forty to a hundred feet, this programme would be as follows. The shaft should be sunk on the footwall side about sixty feet outside of the ore-body and near its centre. Levels are then established at suitable intervals, usually 125 feet. On each level, a cross-cut is run to the ore-body, and there a main-haulage drift is driven in either direction to the end of the ore. Cross-cuts are then run at 25-foot intervals, so that ore-chutes can be spaced about 25 feet centre to centre each way. It is not necessary that these cross-cuts be extended to the walls of the ore-body, if the position of the walls is known; they are extended just far enough to make room for the correct location of the chutes.

Jan 1, 1934

By D. Asefi

A new method to detect microstructural features such as recovery and recrystallization as well as cold rolling reduction in low carbon steels was developed based on magnetic hysteresis loop measurement. To this aim, a hysteresis loop measuring apparatus, specifically designed and assembled for plate samples was employed. It is shown that maximum field (Hmax) of hysteresis loop, measured at constant maximum flux density (Bmax) of 0.5T, is an adequatemagnetic property to monitor different stages of changing microstructures during annealing.

Oct 1, 2011

By S. Kamado

Development of new SF6 alternative cover gas with low global warming potential is strongly desired for melting and casting of magnesium alloys. We have tried to apply several kinds of HFC and HFE gases with low potential from 30 to 950 as protection gases to AZ91D alloy melt in the temperature range of 650 to 800°C. As a result, protective film consisted of MgF2 and MgO is formed on the melt surface and ignition-proof effect is sufficiently obtained at all the temperature ranges even when flow rates of mixed gases containing CO2 as a carrier gas are almost the same as those using SF6 gas. Reduction of global warming potential exceeds 98% at 650°C and 89% at 800°C in comparison with a mixed gas of CO2 and SF6.

Jan 1, 2006

By Robert J. McCarthy

There are two things on everyone's lips when mining folks gather these days - one is the exciting business opportunities that now exist for mine development and expansion, and the other is the dire shortage of human resources needed to design, manage, and even operate the mines. Years of stagnant industry growth, limited employment opportunities, and unwarranted perceptions of remote and harsh working conditions have caused mining to be a less than desirable career choice. Attrition and reduced entry to the workforce has resulted in shortages for not only mining professionals, but also skilled trades people and operators. Consequently, to survive, let alone grow, mining companies, suppliers, and educators are all pursuing innovative solutions with technology, inter-industry recruiting, centralized services, and strategic partnerships. This paper describes some of these initiatives and proposes others, now that the people are gone!

May 1, 2008

By John Mair

The Ilimaussaq Intrusive Complex in south Greenland is a layered alkaline igneous body that is predominantly comprised of agpaitic nepheline syenites. The Complex is now recognized as containing vast resources of uranium in polymetallic ores that are also strongly enriched in rare earth elements (REEs) and zinc. Uranium and REEs are dominantly hosted in phosphate minerals with a minor proportion hosted in zirconium silicate minerals. Equivalent ores are yet to be mined for uranium anywhere in the world; however, studies are well advanced in confirming a process route to economically extract uranium. The Ilimaussaq Complex is considered the world?s type-locality for agpaitic rocks. Formation of the complex is attributed to four successive pulses of magma. The first produced an augite syenite, which now forms a marginal shell. This was followed by intrusion of a sheet of peralkaline granite. The third and fourth stages make up the bulk of the intrusion and are peralkaline to hyper-agpaitic in composition. The third batch of magma differentiated to produce pulaskite, foyaite and naujaite. Stage four produced the kakortokites and lujavrites, which are the units of particular economic significance. Kakortokites are strongly enriched in zirconium, niobium and tantalum, whereas the lujavrites are strongly enriched in uranium, rare earth elements, fluorine and zinc. Lujavrites are vertically zoned with arfvedonsite (black) lujavrites grading downward into aegerine (green) lujavrites. The upper most portions of the black lujavrites contain uranium concentrations of greater than 450 ppm, which decreases toward green lujavrites where uranium concentrations rarely exceeds 200 ppm. Resources defined to date in accordance with the Australian JORC code include 282 M lbs of uranium oxide at a grade of 280 ppm. With scope for several other similar sized resources within complex, the overall potential resource is of immense global significance. Metallurgical studies to date indicate that uranium can be successfully extracted from black lujavrites via an alkaline pressure leach method. This involves selectively leaching uranium with solutions containing carbonate and bicarbonate at elevated temperature and pressure. Uranium can then be recovered by hydrogen reduction to create a uranium oxide product. There is also scope to beneficiate ores as uranium and REE?s are hosted in specific mineral groups. Phosphate minerals can be effectively concentrated by froth floatation and uranium-bearing silicate minerals can be concentrated by gravitational methods. Studies indicate that REEs can be extracted from the residue following the alkaline leach process by a dilute hydrochloric acid wash, with REEs then precipitated in the form of a REE concentrate.

Aug 1, 2010

By J. D. Bateman, A. S. Dadson

"The Giant claims are on the west side of Yellowknife bay about 1 ½ miles north of the settlement of Yellowknife. They were staked in 1935 by prospectors in the employ of Burwash Yellowknife Gold Mines, Limited, and were transferred to Giant Yellowknife Gold Mines, Limited, in 1937, on the incorporation of that Company. During the period 1936 to 1940 a number of surface discoveries were investigated by trenching, test pitting, and diamond drilling. A shallow inclined shaft was sunk on the Brock zone, a system of narrow and irregular quartz veins, and some 75 tons of high-grade ore was mined and shipped to the Trail smelter. In 1943 management control was acquired by Frobisher Exploration Company, Limited. An intensive campaign of diamond drilling was commenced in January 1944 and carried on continuously for 2 years. This drilling indicated the presence of substantial gold orebodies lying within well-developed shear zones. Two shafts, 1 ¼ miles apart, were sunk during 1946 and underground development started on two of the orebodies.The claims are underlain largely by rocks of the Yellowknife greenstone belt, which extends from the shore of Great Slave lake along the west side of Yell ow knife bay and northward . The most conspicuous structural features are the steeply dipping late faults. The chief of these is the West Bay, which bisects the greenstone belt at an acute angle and crosses the southern part of the Giant group. At the 'big bend' near the west boundary of the claims there is a remarkably sudden change in the strike of the fault, from about 12° N.W. to about 3° N.E. The apparent horizontal displacement along this fault is of the order of 3 miles, with the east side moved relatively north. There are also a large number of lesser faults with apparent horizontal displacements of a few feet up to l,70J feet for the Townsite fault. Most of these faults trend north to northwest. Surface examination indicates that, at least for most of them, the movement corresponds to that along the West Bay fault, that is, the east side moved relatively north. According to the available evidence, all or most•of the movem:nt along the West Bay fault and along the lesser faults was post-ore. Late diabase dyk:s that cut through ore-bearing shear zones, with chilled margins in contact with the mineralized material, are apparently displaced to the same extent as earlier geological markers. ( see Frontispiece. )"

Jan 1, 1954

By R. M. Kalanchey

The application of pressure oxidation processes to copper feed materials has gained increased exposure in recent years and some of these processes have made commercial inroads, although rather limited to date. Among the hydrometallurgical processes with significant commercial potential, Dynatec's copper pressure leaching process has been applied to arsenic-bearing copper materials and has shown, through a number of batch and continuous test programs, that pressure oxidation is a technically feasible option for the recovery of copper with coincident sequestration of arsenic in an environmentally benign residue.

Jan 1, 2007

By R. Heikkilä

Fluent information exchange between different work phases, software and systems used in infra construction is a key for successful execution of infra construction projects. Open and publicly available information formats with the determined data models aim to facilitate the interoperability between different software and systems developed by competitive vendors. While building and construction industry has developed and used IFC format for years, infrastructure sector has just recently started to target clear efforts on the development of open information formats for infra construction processes. In the paper, a new Inframodel3 extension just developed in Finland and based on the LandXML1.2 international standard is to be introduced. The aim of the Inframodel3 was set to meet the requirements of information transfer needed especially between BIM based design software, measurement systems and 3-D machine control systems used in road, railway and watercourse construction projects. Some test results are reported and evaluated in the paper. In the field of bridge engineering, the IFC format and IFC Bridge extension have been tested and evaluated in Finland. The results from the experiments show and verify as well the applicability of these open formats to the information exchange requirements in bridge engineering. The current limits for open information transfer of these formats are shown. The active co-operation with the International Building SMART Organization has led to the achieved status and position for both the Inframodel3 and IFC Bridge formats and hence the continuing international support provided by Building SMART.

Aug 1, 2013

By O. Moselhi

The purpose of this research is to evaluate the impact of Building Information Modeling (BIM) on Just-In-Time (JIT) material delivery, with a focus on how the use of BIM can help improve efficient implementation of JIT and reduce the cost of material management. Previous research and a number of case studies have addressed the positive impact of BIM on construction at large but none focused on JIT in construction. This paper presents a methodology for selecting reliable material vendors. It also utilises the integration of BIM and scheduling software to generate quantities of material and its required delivery time to improve the flow process and improve its reliability to minimise related delays and productivity losses arising from idle and non-productive time of equipment and labour on jobsites. 4D visualization is utilized to support coordination and timing of JIT material deliveries in an effort to minimize congestion on job sites. Case studies on JIT material deliveries are presented and the impact of BIM implementation on reducing the cost of material management is evaluated. The joint effect of BIM and JIT on quality control, elimination of waste, reduction of inventory buffers, and on relationships with material vendors are evaluated by analysing and comparing data from case studies. The paper also presents a methodology based on multi-attribute decision criteria for modelling the selection criteria for material vendors. The model can assist in ranking vendors not only based on cost and quality but also on their reliability in delivering material on time.

Aug 1, 2013

By Alireza Entesari

Removal of metal ions from effluents represents a significant technical challenge. As a consequence several industries, including mining, are faced with issues relating to removal of contaminant cations and anions from solution. This study evaluates three natural mineral materials referred to as basalt, scoria, and calcined shale for treatment of metal contaminated effluents by adsorption. Adsorption tests were conducted to asses the possibility of removing cationic and anionic metal ions from prepared solutions and mine water effluents. Sustainable production of industrial minerals requires that a diverse range of added value products be introduced.

May 1, 2006