Search Documents

By Akira Miura, Katsuyuki Sato, Yuken Fukano

JX Nippon Mining and Metals Corporation has developed the JX Iodine Process, which is an innovative and patented copper-leaching process for low-grade primary sulfide ores. This process consists of the irrigation of ferric iron and a low concentration of iodide solutions. One-meter column leaching tests were conducted on ore samples from two different mines. At the end of experiments, the total copper recovery exceeded 70% for Sample A and 50% for Sample B with the iodine method, which was significantly higher than that with conventional ferric leaching of 14% for Sample A and 20% for Sample B. To elucidate the reason for the JX Iodine Process effectiveness, cross sections of leached residues were studied. Reaction products were confirmed around chalcopyrite even in the central area of particles in Sample A, however, reaction products were recognized at a depth of only 1 mm from the ore rim in Sample The resistance of Sample A to the leachate appeared to be lower than that of Sample B because Sample A had a high permeability and porosity, whereas Sample B had been affected strongly by a potassium alteration. No reaction products were visible on conventional leaching samples, even at the ore surfaces. INTRODUCTION Hydrometallurgical copper leaching (heap leaching or dump leaching) has been used extensively for copper recovery from oxide and secondary-sulfide ores, but not for primary copper sulfides, which contain mainly chalcopyrite as copper minerals. Although they are major resources of copper, primary copper sulfides are difficult to process because of their refractory nature. Extensive leaching studies have been carried out to leach primary copper sulfides (chalcopyrite), including biological and chemical, using a variety of oxidants and additives to enhance copper recovery. Watling (2013) reviewed acid-chloride-oxidizing agents with chalcopyrite. Abdollahi et al. (2015) tested silver as a catalyst for bioleaching with a chalcopyrite-bearing molybdenite concentrate. Hiroyoshi, Miki, Hirajima and Tsunekawa (2000) found a specific redox-potential zone for high-speed chalcopyrite leaching by controlling the ratio of ferric and ferrous iron. However, no ambient-temperature economic process has been developed for leaching primary copper sulfide, which usually has a low copper grade.

Jan 1, 2019

By C. Gaubert, G. Bourassa

"The construction or rebuild process in the anode baking furnaces has been modeled with the software Rockwell Arena, in order to minimize the process cost and risk. The case study was focused on the sectional rebuild (""on the fly"") that needs a high coordination of the material inventory, the on-site personnel and the construction/production schedule. Multiple entities and resources were allocated for the different part of the process (in-furnace process, prefabrication, materials transportation, etc.). Logic flow charts and VBA macros were used to simulate the space utilization (including cranes utilization) and interaction with production. MS-Excel output files can show user-friendly results."

Jan 1, 2006

By R. Gordon, J. Palich, W. Qian

The EarthProbe DCIP system deploys tightly spaced electrodes connected to a centralized data acquisition system that enables arbitrary selection of current and potential electrodes through relays. Rapid data collection (approximately 1000 readings per hour) and advanced signal processing allow for efficient use of conventional and novel arrays and the removal of natural and cultural noise. What is unique about the system is its electrode and borehole cable design, which allows seamless integration of borehole and surface measurements. EarthProbe operates in four configurations - surface, borehole, borehole-to-borehole, and surface-to-borehole (a variant of the borehole-to-borehole configuration).

Jan 1, 2011

"Cobalt refining at Vale Canada (previously known as Inco) has been associated with Ni production. Because certain compounds of both metals carry risks for adverse health endpoints by inhalation exposure, it is critical to understand the aerosol concentrations of specific substances and the metallurgical processes through which they enter the air. Vale Canada has therefore decided to describe the histories of its Ni-related operations and to report industrial hygiene measurements when available. This paper describes electrolytic Co operations carried out at Port Colborne, Ontario (1954–1966), and provides aerosol measurements (1995–2008) for current Co electrowinning operations.RÉSUMÉ L’affinage du cobalt chez Vale Canada (anciennement Inco) a été associé à la production de nickel. Puisque certains composés de ces deux métaux comportent des risques d’effets néfastes pour la santé par exposition à l’inhalation, il est essentiel de comprendre les concentrations en aérosol des substances spécifiques ainsi que les procédés métallurgiques par lesquels ils entrent dans l’air. Vale Canada a donc décidé de décrire les historiques de ses opérations liées au nickel et de divulguer les mesures d’hygiène industrielle lorsqu’elles sont disponibles. Le présent article décrit les opérations électrolytiques effectuées sur le Co à Port Colborne, Ontario (1954–1966), et fournit des mesures de la teneur en aérosol (1995–2008) pour l’extraction électrolytique actuelle du Co."

Jan 1, 2015

By Chao Yang, Liguo Tian, Yan Yang

"The Jinfeng gold mine is one of the three gold mines that Eldorado Gold has in China and it is the second largest gold mine in China. The mine is located in a relatively remote and mountainous area in the southwestern Guizhou province. The orebody is similar to the Carlin type deposit in Nevada. The mill throughput was designed to treat 3,600 tones per day. The ore comes from open pit mining and underground mining, and is fed to one-stage jaw crushing. The crushed ore is stockpiled, reclaimed and then fed to the SABC grinding circuit. After classification with hydrocylones, the ore is floated, and the resultant concentrate is oxidized biologically in a process known as BIOX®. The oxidized concentrate is then washed in a CCD circuit and finally leached with cyanide in a CIL circuit for gold extraction. Jinfeng produces about 180,000 oz of gold per year.This paper introduces operations and modifications of SABC circuit over the past three years, and then describes some technical characteristic of the SAG mill and other circuits in the processing plant.Major modifications and improvements on the SABC circuit are described in the paper, including:1. Impacts of grinding ball and mill liner with respect to material selection, quality, hardness, manufacturing methods, and interactions between mill liner and grinding ball.2. Effect of milling operation parameters on milling efficiency.3. Impacts of SAG mill scats and modifications of grate size to improve mill throughput.4. Design and construction of a pebble crushing system, and recycle the crushed scats to the SAG mill to improve mill throughput.With the above-mentioned modifications, 20% increase over the design in mill throughput has been realized over the past three years, and operating cost has been significantly reduced. However, some issues still remain, and thus process modifications and technical innovations are still needed."

Jan 1, 2012

By Roderick C. McDonald

Great Bear lake, the fourth largest body of water on this continent, comprises an area of approximately 12,000 square miles, and is set astride the Arctic circle, with a large portion of it witnessing both the Arctic winter night, and the Arctic summer day with its midnight sun. The very name itself, Great Bear, suggests an Arctic region. The seasonal contrasts at Great Bear lake are very marked by the cold and darkness of winter, and the warmth and brightness of summer. Signs of winter such as low clouds, snow, sleet, fog, and night frosts, generally appear the latter part of August, while ice forming on bays during the last two weeks in September ends boat travel on the lake about September 30th.Early in June the ice leaves the river mouths, during the last ten days of the month it disappears from small bays, and at some time during the last two weeks of July the main body of the lake becomes navigable. In 1916, the ice disappeared earlier than usual, and the lake was navigable on July 5th. Great Bear river generally breaks up about June 1st, but, on account of ice cliffs and floes, it is not navigable with safety until early in July. Even then, the traveller is confronted with the Charles rapids, but these might be overcome by a wagon or motor road, such as the one from Fitzgerald to Fort Smith: However, in 1931, Mr. A. W. Boland, Fort Norman, N.W.T., carried with scow and motorboat practically all freight between Fort Norman and LaBine point and Hunter bay, at the east end of the lake. During July and August, two types of clothing are required, for, although the days are mainly ones of warm sunshine, the nights are cloudy and cold. In the winter season, fur clothing is used exclusively. Considerable timber, mainly white spruce, suitable for fuel and building purposes, borders the lake and extends eastward to the Coppermine river. North of the lake, no timber is found except in the river valleys, but with oil and coal possibilities near Fort Norman, the fuel situation might be solved.

Jan 1, 1932

Some examples of the results of research projects, conducted in the KOMAG Institute of Mining Technology are presented. Special attention is paid to mining machines and equipment, and improving work safety and comfort of miners in underground workings. From numerous scientific and technical achievements of the KOMAG Institute within the last 2 years, a few design solutions have been selected for a presentation. Some results of European projects on innovative solutions are described as well, highlighting KOMAG?s role in the national and international research area.

Aug 1, 2013

By B. D. Thompson

Many mines adopt necessarily conservative backfilling strategies due to a lack of understanding of their backfill behaviour. In the past five years, extensive instrumentation campaigns have focused on measuring in-situ cemented paste backfill behaviour. These tests have resulted in optimised backfilling efficiency through elimination or reduction of cure periods where; i) controls on backfill behaviour are understood, and ii) barricade pressures are demonstrated to be within a safe range using routine monitoring as a required QA/QC procedure. Recently, this work has been extended to consider hydraulic backfill operations. Two stopes have been instrumented at Vale?s Coleman and Garson Ramp mines. The instrumentation and deployment methods are discussed, and representative total earth pressure, pore pressure, and temperature data are presented. In one case, pressures in the stope are relatively low as drainage causes strength gain in the fill and so pressures are arched. In a second example, again, drainage causes strength gain in the fill, but increasing temperatures correlate with pressure increases even during downtimes in filling. These pressure increases are thought to be caused by thermal expansion of the backfill in confined locations. Generally, the instrumentation approach has proven successful in measuring hydraulic backfill behaviour and offers good potential for incorporation into a procedure to safely maximise backfilling efficiency through routine barricade pressure monitoring, when combined with safeguards to ensure adequate fill drainage.

Aug 1, 2013

By Jianglan Duan, Steve L. Cockcroft, Andre B. Phillion, Carl Reilly, Daan M. Maijer

"In the aluminum alloy wheel casting process, careful design of the cooling system in the die and its operation (cooling channel timing) are critical to achieve quality and productivity goals. The problem is challenging owing to the cyclic nature of the process and the relatively large thermal mass of the die in comparison to the wheel. For a given die geometry, a set of constraints have been defined to ensure directional solidification and an objective function, based on cooling rate during solidification, has been defined to reach a target secondary dendrite arm spacing. The methodology presented in this study employs the commercial finite element package, ABAQUSTM, and an optimization module based on the open source library, Scipy. The developed methodology has been applied to a series of geometries and cooling system configurations, including a 2-D axisymmetric wheel and die assembly generated from a prototype die. Preliminary testing has shown that careful selection of the objective and constraint functions have made it possible to reach desired solidification pattern.TM- Dassault Systèmes Corp."

Jan 1, 2014

By M. Mahdi, L. So, A. MacMillan, D. Metcalfe, J. Woloshyn, D. Sauter, N. Uys, JP. Janse van Rensburg

For city smelters, with limited real estate, efficient slag cleaning furnaces followed by water granulation to produce an iron silicate product is the preferred process approach. Water granulation, however, consumes large volumes of water and requires high maintenance due to abrasive slag/water slurries. Air granulation offers an alternative to water granulation, which eliminates water use and has low maintenance requirements. Although full-scale operation has not been implemented for copper slags, full-scale operation for platinum group metal (PGM) converter slag has been implemented. A review of full-scale air granulation performance for PGM converter slag is provided. Based on PGM converter slag granulation performance, parallels to copper slag granulation are drawn and full-scale operation for copper slag is modelled using computational fluid dynamics (CFD). INTRODUCTION Typical slag management practices in the copper industry include dumping, slow air cooling, and water granulation, as shown in Figure 1. Dumping is the most commonly used slag handling method for most metal production plants, but presents challenges including the requirement for a large slag pit, requirement for expensive/high-maintenance “hot” mobile equipment, risks associated with transportation of molten slag, and no value recovery from slag as a sellable by-product or from slag as a source of heat.

Jan 1, 2019

By Curtis Rempel, John Bartlett, Alex Holtzapple

METSIM is a powerful program capable of modelling and simulating every known metallurgical and inorganic chemical process. METSIM is used by companies throughout the world to design, simulate and control operations from mine to tailings and everything in between. At its absolute simplest, METSIM can be used to create a process flowsheet. METSIM modules and built-in unit operations cover mass and energy balances for either steady-state or dynamic simulations of mine, stockpile, heap leach, material handling, comminution, beneficiation, hydrometallurgy, pyrometallurgy, gas and steam handling, and tailings management processes. Data for the material being processed can include mineralogy, particle size analysis, grade by size or multicomponent size analysis, washability data, mechanical, physical and thermodynamic properties. METSIM is written in APL (A Programming Language). Unlike C++, APL is simple and easy to learn, allowing the user to program whatever they can imagine, without first obtaining a degree in computer science. METSIM can also interface with EXCEL and other software through dynamic data exchange (DDE), allowing data to be imported and exported for viewing, analyzing and controlling. METSIM can answer simple or complex metallurgical and process questions allowing the user to predict and engineer without the issues of clumsy and tortuous spreadsheets.

Jan 1, 2014

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

For developing new technologies, it is important to characterize the microstructure of materials with high spatial resolution at the nanoscale. To achieve high resolution, field emission scanning electron microscopes (FE-SEM) were developed. These microscopes allow working at low accelerating voltage, below 5 kV, to take advantage of the reduction of the interaction volume with accelerating voltage. Furthermore, their higher gun brightness compared to conventional thermo-electronic emitters, allow a probe size at the nanoscale. At low accelerating voltage, the emission volume of backscatter and secondary electron (SE) of the type II signals approach that of SEI signals. However, it is not enough to reach the highest resolution. A magnetic field above the sample improves the spatial resolution by collecting mostly high-resolution signals. In addition, the energy-filtration of the electron signals allows selecting the type of contrast detected: topographic, compositional, or crystallographic. The development of these new technologies permits to extend the imaging capabilities of the SEM towards new nanoscale applications.

Jan 1, 2014

By David Stone

The Beal Mountain Mine near Anaconda, MT is an interesting case history of a mine that has continued operations despite several large pit wall failures over a period of about 10 years. The largest event involved some 3.9 million tons of rock that has moved steadily at a rate of about 0.05 ft/day since 1992. This paper documents the geotechnical instrumentation and monitoring programs implemented at Beal to provide the company with a comfortable baseline that supported ongoing operations. The success and failure of a variety of stabilization measures will be discussed, along with typical instrumentation responses for several significant events. The success of Beal Mountain serves as a good model for mines faced with serious geotechnical challenges.

May 1, 2001

By M. J. Lopatka

This paper presents the results of field test and theoretical analysis driving resistance articulated 4x4 tracked robot test-bed. Tests were made on four different grounds. Designated elastomeric tracks resistance coefficients are much higher than for steel tracks. This information was important for the proper estimation of energy consumption in the process of driving.

Aug 1, 2013

Introduction ?MT involves the measurement of naturally occurring magnetic and electric field oscillations. ?The ratio of E/H (wave impedance) is measured as a function of frequency to give resistivitydepth information. ?The ratio of vertical and horizontal magnetic fields (tipper) gives information about the location of (channeled) current systems.

May 1, 2008

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By F. Shi

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT’s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By C. K. Baxter, A. Odeshi, M. Mohammadi, E. D. Cyr

"Metal additive manufacturing has been a revolutionary step in designing new complex shapes with faster and cleaner building capacity in comparison to subtractive manufacturing processes. The ability to print lightweight alloys such as aluminum has made metal 3D printing attractive to different industrial sector from aerospace to energy and bioengineering. Of particular interest in this study, are the mechanical and microstructural properties of AlSi10Mg-200°C alloys. In this project, samples were 3D-printed in horizontal direction using an EOS M290 machine by Direct Metal Laser Sintering (DMLS) technique. Uniaxial tensile tests and high strain-rate impact e tests were carried out to investigate the mechanical properties and to study the repeatability of the process. A constitutive model is developed to predict the results of the mechanical tests at varying strain rates to better understand the high strain-rate behaviour of these alloys. Using optical microscopy, features such as scan tracks and melt pools within the AlSi10Mg-200°C samples were observed, and the microstructure was observed to be homogenous. The previously listed tests were compared to the results obtained for similar cast alloy counterpart, i.e. A360.0.INTRODUCTION A relatively new way of manufacturing parts is on the increase as rapid prototyping becomes increasingly popular throughout the world. Additive manufacturing is a process which, given a 3D model, uses metallic material in powder form to build a part layer by layer until completion (Gu, Meiners, Wissenbach, & Poprawe, 2013). This way of rapid prototyping is very attractive in comparison to other possibilities because of its ability to accommodate complex design and geometries. Conventional manufacturing methods have limitations when it comes to complex geometries, but additive manufacturing allows for increased design flexibilities while maintaining a light and stable final product (Murr et al., 2012). It also allows for a reasonable cost, especially for small batch sizes that would otherwise be extremely expensive."

Jan 1, 2018

By J. H. Pateson, D. C. Comrie, D. J. Ritcey

"Geopolymers are inorganic semi-amorphous three dimensional silico-aluminates of the poly(sialate) type (-Si-O-Al-0-) or of the poly(sialate-siloxo) type (-Si-O-Al-O-Si-0-). Polycondensation occurs at low temperatures with geopolymers being stable up to 12oo0 c. Research, development and application technology pertaining to geopolymers is being undertaken jointly with Dr. Joseph Davidovits of The Institute for Applied Archaeological Sciences of Florida, U.S.A. This joint focused upon the chemical Barry University in Miami Shores, research and development program has stabilization and solidification of various waste products through geopolymerization. Of particular interest is the geopolymerization of mine wastes including tailings and waste rock derived from the processing of base metals, precious metals, potash, coal and uranium deposits.INTRODUCTIOND. Comrie Consulting Ltd., in cooperation and technical liaison with CANMET, Ottawa has been testing the application of geopolymers to mining wastes. Corporate efforts to date have concentrated upon reactive acid tailings, principally from the abandoned Kam-Kotia Mine site, and dewatered paint waste sludges. Test work conducted to date has successfully yielded geopolymer treated materials and wastes with increased chemical and structural stability. Wastes containing heavy metals, cyanides, arsenic and sulphur dioxide have been successfully geopolymerized."

Jan 1, 1988

By D. Seke, E. Katsande, R. Khumalo, K. Seerane

Palabora Mining Company (PMC) processes a multi-component ore body using a circuit consisting of two AG mills in parallel, closed with vibrating double deck screens and hydrocyclones. The bottom screen undersize feeds the hydrocyclones, but the screen oversize products can be treated in a variety of ways. The top deck screen pebbles can be crushed and then combined with the bottom deck oversize and recycled to the AG mill. Alternatively both the top and bottom deck screen oversize can by-pass the recycle crusher and be recycled directly to the mill. A full tap-off is a configuration when both the top and bottom deck screen oversize streams are stockpiled. The other configuration is when the bottom deck screen oversize is recycled to the mill while the top deck screen oversize is stockpiled - termed partial tap-off. This article reports the findings from the surveys performed to evaluate the performance of the PMC auto mill circuit when operated under the four different configurations discussed. Ore characterisation tests were performed to assess the deportment of the key ore components for the different configuration.

Jan 1, 2012