Search Documents

By EJ. Reichhardf

The Molopo Farms Complex is a major, layered ultramafic/mafic, early Proterowic intrusion which is totally covered by sediments of the Karoo and Kalahari Fonnations and situated in southern Botswana and northeastern South Africa. The approximately 3000 m thick, generally fine- to medium-grained ultramafic and mafic cumulates are intrusive into equivalents of Thmsvaal Supergroup sediments and lavas. Multiphase defonnation resulted in tilting and segmentation of the Complex into individual tectonic blocks. Sr isotopes document at least two chemically distinct parental liquids which interacted in a complex manner to form an approximately 1000 m thick rhythmically layered succession which straddles the ultramafic/mafic boundary. Repeated mixing resulted in a complex cryptic layering pattern and numerous sulfide-enriched layers which contain significant PGE+Au concentrations.

Jan 1, 1994

By F. G. Smith

Abstract Laboratory methods are now in use whereby the temperature and pressure during the crystallization of hydrothermal minerals can be determined. The techniques include the use of the decrepitation method of studying liquid inclusions, and electrical measurements of pyrite. The determinations are sufficiently accurate that the data can be used in solving a variety of ore deposition problems. Within the last year, several new laboratory techniques have been developed in the Geochemical Laboratory of the Department of Geological Sciences, University of Toronto. The results of several tests of ore by these methods have proved to be useful in treating some problems which previously were considered unsolvable. It is now possible to determine the temperature of deposition of most of the minerals in a hydrothermal ore deposit, also the depth below the surface during deposition. Measurements can also be made of the reopening history of a complex ore. The temperature-pressure determinations depend upon the fact that minerals deposited from a hydrothermal solution always trap a small amount of the solution at the time of crystallization. The solution, being predominantly composed of water, has a density which depends upon the temperature and the pressure prevailing during crystallization. After ore deposition is complete, erosion and isostatic uplift finally exhumes the vein. During this slow fall in temperature and pressure, the solution contracts and a gas bubble appears. If the trapped solution in the mineral is examined, the gas-liquid ratio records the density of the solution at the time the mineral was deposited (except for a slight change in the volume of the mineral). The thermal expansion and compressibility of water and water solutions are known to a sufficient degree that, if the gas /liquid ratio can be determined, the temperature-pressure relations during deposition can be calculated.

Jan 1, 1949

By Behzad Vaziri Hassas, Firat Karakas, Esra Tanisali, Mehmet S. Çelik, Ahmad Hassanzadeh

Coagulation is basically an aggregation process where particles settle under the influence of interfacial forces with electrostatic forces playing a governing role. Although particle morphology consisting of shape and roughness dictates the physical encounter of two particles, their eventual coagulation is not only influenced by columbic forces but also other interfacial forces such as hydrophobic interaction, which affects the extent of aggregation of particles through increasing the distance of interaction. Roughness is well known to increase the effective contact angle on hydrophobic surfaces and also enhance interfacial forces. In this study, the effect of morphology of particles and particularly roughness on the settling velocity and in turn coagulation tendency was investigated. Batch settling tests (BSTs) of different particle morphologies were investigated as a function of pH. Two different morphologies of silica particles were utilized with the same particle size distribution (PSD) including smooth-spherical and rough-spherical (Etched). Rough particles were prepared by acid etching technique using hydrofluoric (HF) at different time intervals (15-300 sec). Etched samples were identified and quantified by optic profilometry. Settling test results showed that the settling velocity of particles in a suspension of 2% solids in the massive settling region is significantly affected by particle morphology of the suspension. Coagulation results further revealed that aggregation of rough particles is faster than smooth-spherical particles. Coagulation results are elucidated on the basis of particle morphology and its effect on distance of separation through hydrophobic forces.

Jan 1, 2016

By J. Mizera, B. Adamczyk-Cieslak, K. J. Kurzydlowski, A. Dobkowska

"AZ31 is the one of the most popular magnesium alloy using in the modern industry. It is well known, that compared with steel, magnesium alloys posse better properties, such as light mass, high specific strength or thermal conductivity. It should be noted that their application is limited by poor corrosion resistance. In this work the corrosion behavior of AZ31 magnesium alloy as cast and after heat treatment were described with the use of testing in neutral salt spray atmosphere.To characterise corrosion resistance and describe layers built on the surface it was necessary to do the metallographic observations with the use of optical microscopy. After that influence of heat treatment for AZ31 corrosion resistance was examined. Measurements were conducted by electrochemical impedance spectroscopy (EIS) and by neutral salt spray tests in artificial atmosphere. Surface and cross section morphology after removal of corrosion products were observed with the use of scanning electron microscopy (SEM).The weight loss measurements show that there is no significant difference between alloys as cast and with following heat treatment.INTRODUCTIONMagnesium and magnesium alloys are popular in modern industry because of the low density and good formability. Magnesium alloys are described by few properties which have got significant influence for their application in transportation and electronics industries (Feliu & Liorente, 2015). Their wide application is limited by poor corrosion resistance. As it is well known Mg is one of the chemically most active metal. Corrosion resistance of Mg alloys depends on several factors, such as impurities, chemical composition or working conditions (Cheng, Qin, Wang, & Zhang, 2009). That all causes that there are many different ways to find well defined and good solution of magnesium alloys processing to improve their corrosion resistance.There are many different versions about the influence of aluminum on the corrosion resistance of magnesium alloy. It is known that intermetallic compounds such as Mg17Al12 due to ß-phase content plays the minor role for corrosion resistance. It is proved ß-phase acts as cathode and it has good ability to build passive layer in broad pH ranges. However it should be noted that mentioned behavior depend on size and distributions of ß-phase in the microstructure (Singh, Singh, & Das, 2015)."

Jan 1, 2016

By Paul J. Beck

The impact of mining development on the environment can be minimized through comp careful construction and accurate monitoring. Key to meeting these objectives is t information at all stages of design, development, operation and decommissioning. This paper will describe cost-effective means of gathering and managing reliable fiel groundwater flow and surface water regime within and surrounding the mine site, as localized contaminant plumes associated with mine operations, and monitoring ground quality. Recent research has led to the development of inexpensive, easy to install syst sampling/monitoring from different zones within a single borehole. Advances in elect developed small diameter probes and pumps for measuring water levels and taking wat continuous monitoring stations in remote areas can be colldeacttaeldo gaguetrosm aatnidc adlolwyn luosaidnegd from a central facility using telemetry systems powered by direct, battery or solar radio frequency, landline or cellular telephones, and satellite. Two case studies will illustrate the use of datalolgagregres sacnadl et eblaesmient rwyi dien mao nitoring sc and the use of multilevel samplers for managing a contaminant plume.

May 1, 2004

By Kimberly M. Curran

The path by which hydrogen supply is provided to any end use application will have a strong effect on the specific economics and price stability for the product supply and the flexibility with which it can be used. The objective of this paper is to present those variables which play a significant role in the selection of the hydrogen production technology, with a particular focus on several typical mining applications. The variables examined include gas requirements in terms of flow-rate and demand profile, overall volumetric consumption, level of interruption tolerable, gas pressure and quality needs. Also examined are the effects of geography in terms of primary energy supply available as well as existing hydrogen sources, developed or not. The role of these factors in the selection of an appropriate supply chain capable of supporting mining applications that use hydrogen as an energy carrier will be illustrated with a typical mining application scenario drawn upon in the form of a case study.

May 1, 2007

By W. R. Bacon

"MAGNETITE HAS BEEN found in many .parts of the coastal area of British Columbia, but the more important deposits are on Vancouver Island and Texada Island. The locations of these deposits are shown on Figure 1.Interest in the magnetite deposits dates back to the 1870s, when land was acquired on the southwest coast of Texada Island by the Puget Sound Iron Company. This ground included the Prescott, Paxton, and Lake deposits. During the years 1885 to 1903, and 1908, 28,898 tons of magnetite ore was shipped to the company's blast-furnace plant at Irondale, Washington, U.S.A. This production was almost entirely from the Prescott open-pits.In the years following the Texada Island discoveries, other magnetite deposits were found in the coastal area, and various plans were proposed to utilize the local ores in the establishment of a steel industry in the Pacific Northwest. None was carried to fruition but, in 1951, open-pit mining was begun at Iron Hill, Vancouver Island, to furnish iron concentrates for steel mills in Japan. In 1952 mining of the Texada deposits was resumed to supply the same market. Production figures for these recent operations are as follows:"

Jan 1, 1949

By George P. Demopoulos

In this paper the author will provide an overview of over 20 years of research & developments in the area of hydrometallurgical arsenic immobilization that culminated recently in the industrial implementation of the atmospheric scorodite process. The paper will consider various aspects of arsenic fixation in the non-ferrous metal industry from the iron-arsenic co-precipitation process employed to arsenic-bearing effluent solutions; to autoclave processing of arsenical copper and gold feedstocks and the fate of the in-situ formed iron sulphato-arsenate precipitate phases; the precipitation and stability of scorodite; the possible stabilizing role of mineral phases like yukonite, and the development of "scoroditeplus" processes employing novel encapsulation strategies. Emphasis is placed on the characterization and long-term stability of the various forms of arsenic-immobilized phases under either oxic or anoxic conditions over a wide pH range and the establishment of critical links between process parameters and hazardous material stability, contributing thus to advancement of new generation safe and sustainable waste management technologies.

Jan 1, 2014

By G. Vibert Douglas

Introduction A preliminary paper dealing with the subject of ore-shoots was presented to this Society at its Annual Meeting last year (1). The present paper records the attempts which have been made during the interval to further this study. In reporting this work, I wish to state that I do not consider the investigation complete; many more experiments will have to be carried out, and more field data will have to be recorded, before the geologist can say with confidence an ore-shoot should start at this point and pitch in that direction. The aim of these experiments is to find some criteria which will serve the mining engineer and mining geologist concerned with ore-shoots in hydrothermal veins.

Jan 1, 1935

By D. Cruden

DISCODAT is a system of computer programs written for CANMET, Canadian Department of Energy, Mines and resources, to be used in analyzing geological data for rock slope design. The programs were written in Fortran IV for an IBM 360/67 computer. A program conditions field data from field forms for storage in a line file. Data may be selectively retrieved from the line file by a general retrieval program which uses a variety of relational operators. The retrieved data may be displayed as structural diagrams or histograms produced on a line printer or in a number of maps produced on a drum plotter. There is a logical sequence which leads to the characterization of those elements of the subfabrics of a rock mass which may be kinematically active. Structural domains within the rock mass can also be outlined by a procedure described as areal analysis. Costs for a complete analysis are usually substantially less than $l/discontinuity.

Jan 1, 1978

By J. Dubinski

Passive tomographic imaging is a technique that can be used for assessing seismic hazard in mines with high seismic activity induced by mining. The basic idea behind such an interpretation is the assumption that there is a relationship between high values of seismic velocity and high values of stresses in the rock mass. This relationship was confirmed both in laboratory an in situ measurements and constitutes the basis for rock-burst and seismic hazard evaluation. In the paper seismic tomographic images of seismic P wave velocity and seismic P wave velocity gradient have been presented to determine rock-burst hazard and locate high seismic activity zones in the area of coal panel 306 in Zabrze Bielszowice mine. The zones of high values of P-wave seismic velocity gradient have been found to correlate with the distribution of high energetic seismic events. Passive tomographic images were obtained using modern bent ray tracing tomography algorithm with regularization. Recent study give rise to observation that not only high values of P-wave seismic velocity is important in seismic hazard assessment as many strong seismic events are located in the areas of high values of velocity gradient. This recent observation permits to increase quality of passive tomographic imaging for detection of seismogenic zones and is presented in the paper. The advantage of passive tomography comparing to active tomography is that sources of seismic waves are generated by rock mass itself and costly controlled explosions are not necessary. Another practical limitation of active tomography is the size of study area which usually do not exceed 200 m by 200 m. This restriction does not appear in passive tomography where area of study is usually 2000 m by 2000 m and the tomographic images delineate velocity structure in locations where mining induced seismicity take place. Passive tomography method utilized in analysis of rock mass state in underground mines encounter some difficulties concerned with the numerical stability of optimization algorithms. In the presented approach to passive tomography problem numerical stability is obtained by special regularization method and by application of very stable numerical seismic ray-tracing algorithm.

Aug 1, 2013

By S. Borle

The microstructural features produced in friction stir welded AZ31, AZ80 and AZ91 alloys are examined when different welding parameters are applied. The microstructures primarily consist of a-Mg grains with a-Mg + Mg17A112 colonies, however melted films of Mg17A112 are produced in AZ91 alloy when high rotation speeds are applied. When the rotation speeds are slow, or the travel speeds are fast the Mg17A112 were incorporated into the stir zone, however they do not exhibit an elongated lamellar morphology associated with melted films. In the case of AZ80, the extruded base material contains a smaller fraction of Mg17A112 and few of these phases are observed in the stir zones. The results are explained based on the dissolution rate and melting temperatures of Mg17A112 controlling the overall morophology and fraction of phases in the stir zone.

Jan 1, 2011

By D. Adiguzel

In this research, providing the sustainability of production quality was aimed for a quarry which is located in Istanbul western part of Turkey and producing concrete aggregates with different types of rock. First, research field was divided in 3 different areas in accordance with the geological differences and parameters that control their product quality, limit values of standards and effect levels were determined. Concrete aggregate conformity tests which are stated in international standards were applied on samples which were taken from these 3 different areas and physical, geometric and chemical properties of each rock type were revealed. The properties of the 3 different types of rock which were produced in the quary were determined and the binary blends were composed. Blending studies were conducted with linear programming technique. In the linear programming model, the cost of aggregate production was aimed to be minimal. The limit values that meet literature and national standards for usability of aggregates in concrete were defined as constraints in the linear programming model and evaluated with objective functions, thus the most suitable aggregate blends were composed. In conclusion, to provide the sustainability of product quality, the most appropriate product blends were composed for the research field and the usability of this model for those quarries were revealed.

Aug 1, 2013

By J .. A. Nemes, I. Ragai

This paper discusses one of the common problems associated with sheet metal forming processes, which is spring back. The materials presented here, stainless steel 410 and Inconel 718, are commonly used in aerospace applications for their superior material properties. Standard tensile tests were performed to determine their tensile properties, as well as material anisotropy. In addition, the effect of anisotropy on springback was assessed experimentally through simple multiple-bending experiments in different directions to the rolling direction. Finally, draw-bending experiments were carried out to study the effect of forming conditions, such as blank holding force, on the final springback angles of the formed parts. For both materials, it was found that the R-values measured for different sheets exhibited variation. However, the specimen orientation does not have a large effect on material tensile behavior or springback angle for simple bending. For the Inconel 718 specimens, the springback angle slightly increases with each stage of deformation during multiple bend experiments. The effect of the blank holding force on springback angles was also examined and found to have a significant effect on thin specimens.

Jan 1, 2006

By Tim Robinson, Michael S. Moats, William G. Davenport, Andreas Filzwieser, Andreas Siegmund, Shijie Wang

This survey continues the long tradition of providing a snapshot of operating data from industrial electrorefineries. It is a supplement to previous surveys that were performed in 1987, 1991, 1995, 1999, 2001, 2003, 2007, 2010, 2013 and 2016. Analyses of current data and historical trends are presented. Examples of innovations to reduce costs, improve productivity, and improve quality are provided. In general, refineries continue to increase productivity while treating anodes with more impurities. INTRODUCTION This manuscript analyzes global survey data provided by operating copper electrorefineries. This paper continues a series of surveys of copper refining tankhouses that started in 1987 (Schloen, 1987, 1991; Schloen & Davemport, 1995; Davenport et al., 1999; Robinson et al., 2003; Moats et al., 2007, 2013, 2016). In this installment, data collected from 2015 and 2018 will be presented and analyzed. The 2015 survey data were presented at Copper 2016 in Kobe, Japan. This survey will continue the analysis of previous data to illustrate long term trends in copper electrorefining, which were originally presented at the Davenport Symposium in October, 2014 (Moats, Robinson, & Wang, 2014). Refineries who supplied surveys are listed in Table 1. Cathode production data from 2015 and 2017/18 (from surveys presented in 2016 and 2019) are provided to indicate which plants provided surveys and when. This manuscript presents operating data for ~6.5 million tonnes of copper production, which represents 30–35% of the world’s copper electrorefining production. The detailed survey results are available upon request from the corresponding author.

Jan 1, 2019

By C. Cekerevac

The paper addresses some geotechnical issues related to the construction of the Deriner dam and HEPP. Design considerations and rock stabilization measures are presented for the excavations which took place in a highly fractured and weathered rock mass prevailing on site. Particularly, the shallow excavations for the overflow spillways tunnels are discussed. These present huge openings that are 12 m wide and 18 m high in portal areas, with an overburden of approximately 20 m, for which numerical finite element analysis and structural discontinuity analysis have been performed to ensure safe excavation process and future operation.

May 1, 2009

By C. -S. Xie, J. -H. Kong

The microstructure and mechanical properties of X80 hot-rolled thick steel strips with a thickness of 17.5mm produced in Wuhan Iron & Steel Company (WISCO) are introduced in the paper. The steel strips as fabricated through proper thermomechanical processing (TMP)/ on-line accelerated cooling (OLAC) processing have shown high strength and toughness, low brittle transition temperature, good weldability, and high Shear Area (SA) percentage in Drop Weight Tear Test (DWTT). The microstructure of the steel strips is characterized with mainly acicular ferrite, and fine dispersed Martensitc-Austenite (M-A) phases. It is determined that the mechanical properties are improved due to the presence of the fine M-A phases and precipitates, which could be formed by reducing the finish rolling and coiling temperatures.

Jan 1, 2005

By A. J. Williams, W. H. A. Timm

"Lake Dufault Mines, Limited, is located north of Noranda, Quebec, and is a producer of copper and zinc concentrates. Various papers have been given on the mill design, construction and operation. 1, 2This paper is intended to describe the application of computer control to the Lake Dufault milling process. A brief history and description of the plant flowsheet will be given, followed by the reasons for installing the computer and the development of the program up to its present use. The success attained to date, comments on economic justification and future plans will also be given.HISTORY AND FLOWSHEETThe Lake Dufault ore body was discovered in September, 1961, and the mill commenced production during August, 1964. The rated capacity of 1,300 tons per day was reached by October 1, 1964. In milling the Lake Dufault ore, many metallurgical problems have been encountered, mainly due to wide and rapid variations in mill heads and oxidation of the massive sulphide ore. However, flexibility in plant layout and the incorporation of up-to-date instrumentation have facilitated its processing."

Jan 1, 1969

By Mitchell Gordon

"In almost all thickener applications the highest possible solid/liquid separation efficiency is what is desired by the user. There is a trend in the industry due to monetary restraints and environmental pressures to look at ways to extract this maximum performance by either retrofitting existing thickeners or installing the most cost effective new thickener. This paper looks at some of the common problem areas and presents a range of solutions developed by Outokumpu Mintec in North America and outokumpu's subsidiary Supaflo Technologies Pty. Ltd.The Emerging PictureAfter many hours of discussions with a large number of plant personnel over the last two years a picture began to emerge regarding current thickening operations in the industry. Initially, it seemed that everybody had their own unique process problems and therefore needed a correspondingly unique solution. Looking more closely at all the cases and the ideas that we had either implemented or suggested, it gradually became apparent that the majority of operators all had one and the same process need ....""Better Separation Efficiency""The range of operational problems that were uncovered in the survey were much more varied than expected and often were not even considered initially to be thickener problems. Often, it was only after the rejection of many solutions to the problem, generally due to capital cost, that the actual cause of the problem was looked at and found to be a thick-ener.A summary of the problems that have so far been identified is presented in Table 1. They are subdivided under three major categories of environmental, process and paste fill to highlight the wide range of mining activities that can be affected by poor thickener performance. These seem to be the major areas where the need for better separation efficiency is rooted."

Jan 1, 1995

By Hong Zhong, Shuai Wang, Gang Zhao, Lanqing Deng, Guangyi Liu

In this paper, three novel surfactants containing double reactive centers(-CONHOH and –CONH-), double hydrophobic groups were designed and synthesized as collector for separation of diaspore and aluminosilicate minerals, such as N-(4-(hydroxyamino)-4-oxobutyl)octanamide (HA-8), N-(4-(hydroxyamino)-4-oxobutyl)decanamide (HA-10) and N-(4-(hydroxyamino)- 4-oxobutyl) -dodecanamide (HA-12). The adsorption mechanism of N-(4-(hydroxyamino) -4-oxobutyl)alkylamides (HA) onto diaspore was also investigated by FTIR spectra, zeta potential measurement and DFT. The flotation results demonstrated that three collectors all exhibited superior collecting power to diaspore and selectivity against kaolinite and illite, and could effectively realize flotation recovery of diaspore from bauxite ores contained aluminosilicate minerals under neutral conditions. Moreover, HA-12 was a superior collector than other two collectors for bauxite separation. The results of XPS, FTIR spectra and zeta potential illustrated that at around pH 6.0, HA might chemisorb on diaspore surfaces through Al-O coordination bonds formed by binding its –C(=O)NHOH or –C(=O)NH– chelate groups with aluminum atoms on diaspore surfaces. HA’s unique properties, such as characteristic bond patterns onto diaspore surfaces, double hydrophobic groups, and intermolecular hydrogen bonds between neighboring HA molecules coated on diaspore surfaces, rendered it to be a superior flotation collector for diaspore.

Jan 1, 2016