Search Documents

By H. Deveci, E. Y. Yazici, A. D. Bas

The leach solutions of waste of printed circuit boards (WPCB) may contain a wide range of base and precious metals with different concentrations due to heterogeneity of these wastes in composition. Therefore, selection of a suitable metal recovery method is of practical importance for downstream processing of pregnant leach solutions of WPCB. Sulphuric acid leaching of WPCB in the presence of a suitable oxidant is capable of dissolving base metals as well as precious metals such as silver. In this study, cementation of silver from sulphuric acid leach solutions of WPCB using metallic copper, aluminum and zinc was studied. The WPCB sample was assayed to have a silver content of 694 g/t. A synthetic leach solution containing 20 mg/L Ag in sulphuric acid solution (0.51 M H2SO4) was prepared based on the silver concentration in pregnant leach solutions of oxidative sulphuric acid leaching tests. Total sulphate concentration ([SO4 2-]T) was kept constant using sodium sulphate at 1 M. Metallic powders of copper (-850 +600 µm), aluminum (-425 +45 µm) and zinc (-45 µm) were used in the cementation tests. The effects of metal type (Cu, Al or Zn), dosage of metal powders (above the stoichiometric ratio by up to 2000-fold) and temperature (20-80°C) on the rate and extent of silver extraction from the solution was investigated. The effect of presence of copper on the cementation performance was also tested. Under suitable conditions high silver recoveries (>90%) was achieved using metallic copper and zinc while aluminum yielded the lowest silver recovery (i.e. 40% Ag). The kinetics of cementation by zinc was comparatively higher than that of other metals. Increasing the temperature was observed to significantly enhance both the rate and extent of silver cementation. SEM-EDS studies were performed to characterise the metallic powders after cementation.

Jan 1, 2016

By A. Probst, J. A. Finch

"Solids concentration (% solids) profiles and the clear liquid/slurry interface level (mudline) were determined from conductivity measurements in thickeners at Falconbridge' s Strathcona mill (Ni concentrate and non-mag thickeners) and Kidd Creek Division (Cu, Zn concentrates and final tails in the concentrator and thickeners in the Zn plant).The conductivity measurement system consisted of a probe 1.5 m in length with 24 electrode cells, a 24-channel relay, a conductivity meter and a computer. A conductivity profile is collected which locates the mud-line by the sharp change in conductivity. The conductivity measurements are readily converted to solids concentration profiles without need for calibration.The results from the conductivity measurements were compared with those from pressure profiles and direct measurements on local samples obtained using a modified Noranda sampler.It is concluded that the conductivity technique is applicable to locate the mud-line and to estimate the solids concentration profiles in thickeners. This on-line information could improve the operational efficiency of industrial thickeners.INTRODUCTIONAn automated, on-line technique for detecting the clear liquid/slurry interface (or mudline) and the variation in solids concentration with depth would enhance thickener operation and control. In some processes such enhanced control offers significant benefits. For example, in hydrometallurgical operations solid/liquid separation is often the process limiting step. Water treatment plants are increasingly expected to operate remotely and reliable sensing is vital.Current attempts to detect the mud-line include reflection of some signal (e.g. sonar), floats (Dahlstrom, 1985) and measurement of pressure (Rosenblum, 1991), and in one case, natural radioactivity of the solids (Johnston and Simic, 1991). A recent commercial development uses reflection from a vertical array of optical transmitters/sensors, which also gives local solids concentration (BTG Inc., 1991)."

Jan 1, 1993

By G. A. Witwicki

"The Thyssen Mining Group of Companies has successfully applied ground freezing technology to numerous projects throughout Europe and North America for over 100 years. Recently, the aspect of data acquisition and data verification has received greater focus.Thyssen Mining has been engaged in several relatively deep shaft sinking projects over the past five (5) years, all of which have required ground freezing to successfully sink through water bearing rock. To safely and economically sink through a quantity of water similar to Saskatchewan’s Potash Mines, it is imperative to understand freeze wall thickness and growth rate.Critical to understanding freeze wall thickness and growth rate, is the collection of accurate data as well as the interpretation of those data. The data can then be utilized to gain a better understanding of the freeze wall growth rate in active projects as well as to provide data to be utilized in modeling for future projects.This paper elaborates on the installation and operation of the data acquisition system utilized at the Newmont Leeville project, Nevada’s first frozen shaft project. In addition, this paper elaborates on the methodology developed by Thyssen Mining to manipulate the freeze wall data derived through the data acquisition system.The successful incorporation of the new system of collection and analysis of freeze wall data for the Leeville Project has given Thyssen Mining a high degree of confidence in the understanding, as well as prediction, of the ground conditions during shaft sinking.This paper will include:•,A brief description of ground freezing and its objective;•,An overview of previous data acquisition methods employed;•,Current data acquisition methods;•,Installation requirements; and,•,Data manipulation and presentation methods."

Jan 1, 2015

By E. J. Marcotte

"IntroductionDevelopments in the preparation, hydraulic transportation and placement of classified mill tailing as an effective backfill and support for mining excavations, have made feasible several advancements in mining methods that are safer and more economical. Hydraulic backfill systems have played an integral part in the development of more efficient cut-and-fill and blasthole stoping.The hydraulic transportation of tailing fill has made possible the elimination of expensive and laborious transportation, placement and spreading of gravel type fills. Also, in cut-andfill stopes, the use of hydraulically placed consolidated fill has largely eliminated the need to use extensive timbering for floors and supports, previously necessary when only gravel type, waste rock or unconsolidated tailing fill was used .Another important advantage of using mill tailing as backfill is that it decreases the need to contain a large portion of the mill solids waste in a surface disposal area and thus reduces environmental and ecological problems.Tailing Fill PropertiesConsolidated tailing fill consists of deslimed mill tailing and Portland cement. These two materials are mixed together in various proportions to form a high density slurry which is transferred underground by gravity through boreholes and pipelines. After placement underground, the water is drained off and the mixture is allowed to set. The strength of the consolidated fill is dependent on the cement content, particle size distribution and curing time. A typical tailing/ cement ratio used for bulk filling in stopes requiring vertical wall support is 30:1. Ratios ranging from 8:1 to 5: 1 are used for stope floors. High pulp densities minimize segregation and loss of cement during placement as well as reduce the amount of drainage water to be handled."

Jan 1, 1989

By T. B. Williams

THE British Columbia Coal Control was established in 1946 as a branch of the Department of Lands. Its functions are the administration of the Goal Act, the making of field and laboratory investigations bearing on the delineation and utilization of British Columbia coal deposits, and the dissemination of information concerning them. The Department of Lands in the Province of British Columbia retains and administers many of the Province's resources until such time as they are actively developed under the departments of Agriculture, of Forests, of Mines, etcc. The work of the Control is one of stock taking and appraising. We are picking up where the geological surveys leave off. In an effort to assist in the orderly, scientific development -of our excellent and extensive' ?Coat resources, we are bridging the gap between exploration and geological examination on the -one hand and mining on the other. All coal analyses required in the course of the investigations, together with? those requested by prospectors and others, are carried out in the very modern and efficient laboratories of the Coal, Petroleum, and Natural Gas Control. At its inception, the Coal Control began an investigation of coal seams in the Peace River area, specifically those contiguous to the Pine River valley about one hundred miles west of Dawson Creek. The occurrence of coal in the Peace River canyon, east of Hudson's Hope, bad been known since 1792, but the first record of production is for 1923.

Jan 1, 1951

By Randy Settgast, Daniel Moos, Hyunil Jo, Ghazal Izadi, Christine Baba

"Analyses of production logs of multiply fractured horizontal wells in unconventional plays show that only a small percent (~30%) of perforation clusters contribute to production. We present in this paper one possible approach to mitigating this problem, based on use of a fully 3-D numerical model of fracture propagation through a heterogeneous medium, by studying the influence both of spacing and of perforation friction on the initiation and propagation of simultaneous hydraulic fractures from a horizontal wellbore. The results indicate that while limited-entry perforating can help to equalize the lengths of fractures simultaneously growing from multiple clusters, it cannot equalize their widths. Both fracture width and fracture length can be equilibrated by combining non-even cluster spacing with limited-entry perforating. This has obvious benefits as it allows equalized placement of proppant across the entire series of perforation clusters, resulting in similar fracture widths and conductivities which enhances the likelihood that all clusters will contribute equally to production.INTRODUCTIONThere is substantial evidence from production logs and other information that during the hydraulic stimulation of horizontal wells, not all perforation clusters within a given stage will produce. One possible cause is the interaction between the hydraulic fractures emanating from each perforation cluster. Typically fractures created at the outer perforation clusters create “stress shadows”, i.e. increases in compressive stress in the minimum principal stress direction, which limit the growth of fractures growing from interior clusters; this is confirmed by modelling [1, 2, 3]. An example of this can be seen in Figure 1 which shows the final configuration of simultaneously propagating fractures from multiple, evenly spaced clusters when there is no perforation friction. The inner fractures are substantially shorter, reproducing the results by Bunger and Peirce [3]. The inner fractures also have substantially smaller widths.One approach to equalize the growth of simultaneously propagating fractures from a horizontal wellbore is by using limited-entry perforating as a method to equilibrate the flow rates into each of the different perforation clusters. Perforation friction is caused by the finite diameter of the entry points into the formation, and leads to a pressure drop across each perforation which is proportional to the flow rate squared. Fractures that take more fluid have a higher fluid velocity through the perforations than fractures receiving less fluid. This causes a larger pressure drop between the wellbore and more rapidly growing fractures, compared to the same pressure drop between the wellbore and the fractures that grow more slowly. Because pressure within the wellbore is approximately the same at each entry point, the larger pressure drop leads to less pressure being delivered to rapidly growing fractures, thereby decreasing their ability to propagate and reducing the amount of fluid they are able to receive. Because the mass rate of injection into the wellbore is constant, this forces more fluid into the fractures that were propagating more slowly, increasing their growth rate. It also increases the pressure required to drive fluid injection. The balance of these effects makes the system largely self-regulating and delivers more balanced fracture growth. While this effect is well known, it is often neglected in current numerical models."

Jan 1, 2015

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By Russell McIntosh

"The Madsen mine is in the southeastern part of Baird township, in Red Lake area, Ontario. It lies about 6 miles southwest of the town of Red Lake, with which it is connected by an all-weather road.The Madsen Red Lake Gold Mines Company was formed in March, 1935, to take over the holdings of the Falcon Gold and Jomac Gold syndicates. During 1935 an4 the early part of 1936 No. 1 shaft was sunk and drifts driven on four levels, all on a narrow quartz vein in a granite dyke.In July, 1936, the Austin zone was discovered about half a mile north of No. 1 shaft by Austin McVeigh, a prospector employed by the Company. Diamond drilling showed that the zone included an orebody worth development, and in 1937 No. 2 shaft was sunk, three levels opened up and sufficient ore outlined to justify the installation of a mill. Milling commenced in August, 1938, at the rate of 300 tons a day, which was later increased to 400 tons a day.The total production from 1938 to 1946 was 1,116,307 tons from which gold and silver having a value of $9,949,010 were recovered. The gold produced ranged from a minimum of 0.1910 oz. a ton in 1939 to a maximum of 0.2827 oz. in 1944. The average grade in 1946 was 0.2345 oz. to the ton."

Jan 1, 1954

By G. E. Wood

Steep Rock Resources Inc. owns a calcite quarry property at Tatlock, Ontario, and a calcite processing plant at Perth, Ontario. The Tatlock marble deposit forms part of an extensive series of carbonate rocks of the Grenville Geological Province in the Precambrian Shield of southeastern Ontario. The deposit is very unusual, if not unique, in the Grenville area in its combination of characteristics of large size, whiteness, high calcium content, low magnesium and silica contents, and scarcity of accessory minerals. A major expansion of the fine grind products capacity of the plant was undertaken in 1982 and came on stream in 1983. The expansion provides important operating benefits at the plant: greater flexibility as to the product mix and reduced dependence on the single grinding mill previously in place. The expanded facility consists of prima,y and secondary crushers, a rotary drye,~ a screenhouse producing a range of screen separator grade products, an airswept Raymond Mill, and a pebble mill with integrated air classifiers, product storage bins, bulk, semi-bulk, and bagged product shipping capabilities, road and rail access, and a substantial product warehouse. The expansion was designed to be compatible with a move into ultrafine calcite production, and is capable of supplying the anticipated sales growth within its market area during the next 5 years. Products are exceptionally white, with good chemistry, low abrasion, and consistent quality. Markets range, according to product particle size, from pre-cast concrete aggregate to fillers for coatings, plastic pipe, and compounds.

Jan 1, 1984

By José L. Carvalho

"Time-dependent swelling deformation of several shaley rock formations in Ontario is a wellknown phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. The swelling phenomenon appears to be related to ion exchange between the rock porewater and the surrounding water.The swelling potential is expressed as the percent swelling strain that occurs per log cycle of time, in either the vertical (perpendicular to bedding) or horizontal (parallel to bedding) directions. In addition, the swelling potential is also noted to be stress dependent. In practice, therefore, the conditions required for swelling are (i) the accessibility to water, and (ii) an outward salt concentration gradient from pore fluid of the rock to the ambient fluid. The relief of in-situ rock stress during excavation serves an initiating mechanism (Lo and Micic, 2010).INTRODUCTIONTime-dependent swelling deformation of several shaley rock formations in Ontario is a well-known phenomenon. In shales and mudstones with a higher salt concentration in the pore fluid than the ambient fluid, the outward gradient generates an osmotic pressure which acts as the driving force for swelling. Swelling is also controlled by the inter-particle bonding; if the bond strength exceeds the osmotic pressure, swelling will not occur, and vice-versa. The bond strength can be reflected by the calcite content which forms cementation bond between rock particles."

Jan 1, 2015

By Jacques Nantel

"The molybdenite property of Brynnor Mines Limited, Boss Mountain Division (wholly-owned subsidiary of Noranda Mines Limited), is situated approximately 360 miles northeast of Vancouver on the east slope of Takom-kane mountain in British Columbia's Cariboo District. Orebodies at the deposit fall into two categories; quartz breccia, and veins and stringers. The development of the breccia ore zone was started in June, 1964. The bulk of the ore is being mined from the stringer ore zone. The ore-body has been divided into 100-foot stopes and pillars. A sub-level blasthole method is used and the broken ore is handled in drawpoints and scram drifts. The development, drilling, blasting and handling of the ore are reviewed. The future pillar recovery operation is also analysed. The paper is also concerned with a scheduled shaft sinking program."

Jan 1, 1970

By C. E. White

The depletion of higher grade mineral reserves will accelerate the trend toward production from progressively larger and lower grade deposits. The discovery of adequate reserves of leaner ores will require the development of improved exploration techniques with a greater depth range. The principal challenges to the Canadian mining industry are to find the mineral resources required to meet fast growing world demand and to develop mining methods and equipment to ensure production costs which will strengthen our position in export markets in the face of in-creasing world competition. The challenges cannot be met without intensive efforts to attract more technical men to the industry and to improve their training.

Jan 1, 1967

By R. B. Fermor

"The tyndalloscope is used in Europe for dust-hazard assessments in both coal and metal mines. Dust-hazard conditions can be directly evaluated by the tyndalloscope in many underground working situations, once the basic standard table or tables have been prepared from representative mine-rock samples.The tyndalloscope is excellent, in many cases, for diagnostic dust sampling during a working shift, because individual readings can be taken to within three-minute intervals. The limitations of the tyndalloscope are also discussed.The author suggests that a combination of both the tyndalloscope and gravimetric sampling methods would be an ideal match for most mine dust-hazard assessments."

Jan 1, 1970

By J. M. B. Scarborough

This paper deals with measures taken to maintain effective operation of heavy-duty equipment in open-pit mining. at Pine Point, N.W.T., during periods of extreme cold weather. The points covered include equipment modifications designed to improve cold-weather performance, effective lubrication of machinery that is vulnerable to extreme cold and operating procedures designed to prevent equipment damage.

Jan 1, 1966

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

By J. C. Allan

THE purpose of this paper is to outline the pogress made in the development o the gravity separation method o ore dressing known as Sink-and-Float, which, in the opinion of the writers, has now reached a stage justifying the claim that this new method marks a highly important advance in the technique . The essential feature of the newest development of this process is the extremely accurate separation achieved. This is responsible for higher extraction in the sink-and-float unit on coarse sizes and, in consequence, for substantially higher overall recoveries. Whilst this is the most remarkable feature of the new process, it has further important contributions to make to ore dressing under the following heads: (1) The introduction of the sink-and-float separator as a buffer helps to iron-out irregularities in the mill feed. By supplying a concentrate of constant grade to the flotation section, the process also indirectly improves overall recovery. (2) The addition of a sink-and-float unit to an existing mill results in substantial increase in capacity at low per ton capital cost. (3) Where the plant can be installed underground for the pre-treatment of low-grade ores, there is a saving in hoisting costs, and excellent 'fill' is provided near the point of use. ( 4) Low-grade mixed oxide-sulphide copper ores may be pre-concentrated, thereby producing a flotation feed sufficiently rich to render the oxide residue from such flotation economic for subsequent treatment by leaching or other methods. (5) Application of the process eliminates hard gangue constituents which cause high grinding costs, or gangue constituents which adversely affect flotation. The plant is compact and easily controlled. No highly skilled operators or expensive reagents are required, and the labour and power per ton are low. The separator is extremely flexible, working equally efficiently on any throughput up to its maximum capacity.

Jan 1, 1940

By Gaston Gingras

"IntroductionL'entretien de l'equipement minier dans les mines à ciel ouvert est une activité qui est aussi vieille que I'existence des mines et qui a progressé au cours des années pour suivre l'évolution des techniques d'exploitation. Lors de la mise en usage de s premières pelles à la va peur, celles-ci étaient généralement entretenues par I ‘équipe de quatre hommes qui était responsable de son opération. Pour les travaux plus compliqués ils utilisaient les services de machinistes qui eux savaient comment réparer Ie moteur à vapeur et couler des coussinets de ""babbit"". Les premières pelles diesel étaient entretenues de la même façon mais pour les réparations au moteur, on devait recourir au représentant du manufacturier qui était Ie seul à avoir les compétences nécessaires.Ce n'est vraiment qu ‘après la deuxième guerre mondiale que I ‘usage de l'équipement mobile s'est répandu dans les mines à ciel ouvert pour débuter les extractions selon les méthodes que I'on connaît aujourd'hui.L'entretien de l'équipement minier de façon organisée à débute avec I ‘usage de ces machines dans nos mines. Ces machines étaient un peu primitives, petites et pas très dispendieuses a I'achat. Même si la disponibilité était basse, elles fournissaient quand même un rendement qui en ces temps était acceptable. L’organisation de I ‘entretien de cet équipèrent était assez primitif et n'occupait qu'une place secondaire aux yeux de la direction de la mine."

Jan 1, 1988

By Sunil S. Gandhi

"The Mountain Lake deposit is a tabular sandstone-type uranium deposit, hosted by the basal unit of Middle Proterozoic Dismal Lakes Group. Uranium occurs mainly as sooty pitchblende disseminated in stratiform lenses within gently dipping quartzose sandstone. It is associated with copper sulphides, pyrite, hematite, and traces of nickel and cobalt arsenides and of silver.Exploration HistoryUranium showings on the PEC claim group were discovered during 1969 by an airborne radiometric survey carried out over the Dismal Lakes-Great Bear Lake area by Aquitaine of Canada Limited (Bizard and Salat, 1969). Some drilling was done in the vicinity of the showings in 1975 by the company under a joint venture with Eldorado Nuclear Limited but the results were not encouraging (Hassard and Woollett, 1975). During 1972, Trigg, Woollett and Associates Limited conducting surveys for Imperial Oil Limited, discovered numerous high-grade radioactive boulders scattered over a distance of several kilometres north and west of the showings, and the area north of the PEC claims was staked as the YUK claims (Ahuja, 1974). A systematic study of the boulder distribution and Pleistocene geology suggested a source additional to the showings. More intensive exploration followed, and in 1976 drilling just north of the PEC claim group boundary intersected the main deposit at a depth of 75 m to 150 m, beneath overburden up to 60 m thick. Part of the deposit extends into the PEC claim group which is under exploration by the Aquitaine-Cominco Joint Venture.The following brief description is based on the presentations in 1978 by F. Hassard of Trigg, Woollett and Associates Limited at the Geoscience Forum in Yellowknife, and by S.S. Gandhi of the Geological Survey of Canada at the Mineralogical Association of Canada Uranium Short Course in Toronto."

Jan 1, 1986

By S. Harvey

The McArthur River deposit is a structurally-controlled unconformity-related uranium deposit. The mineralization is situated at the intersection of a pronounced fault zone, referred to as the P2 fault zone, and the unconformity between Paleoproterozoic Wollaston Group metasedimentary rock and Paleoproterozoic to Mesoproterozoic Athabasca Group. Mineralization is variably hosted within the Athabasca Group fault wedge and the faulted basement, consisting of twelve zones covering a strike length of 2,700 m. The main P2 fault zone consists of several reactivated foliation-parallel faults containing narrow seams of graphitic clay gouge that are separated by highly cleaved, graphitic wall rock. The mine grid east-dipping P2 fault zone is characterized by reverse offset of the unconformity surface. It varies from a single discrete fault to splay offsets consisting of two to three individual splays. The combined vertical offset along the P2 fault zone is a maximum of about 80 m. The fault has emplaced a wedge-shaped sequence of Wollaston Group metasedimentary rocks into the Athabasca Group. Foliation-oblique faults occur throughout the McArthur deposit trend. Steep east-northeast trending faults generally exhibit apparent oblique dextral sense of shear. Less common, and possibly conjugate, are steep faults trending east-southeast with an apparent sinistral sense of shear. Offsets are generally less than 10 m on these structures. South-trending and shallow west-dipping brittle faults with offsets less than 1 m are also observed while rare steep, north-trending faults are also noted locally and played a critical role in development of the Zone 2 basement-hosted mineralization.

Jan 1, 2020

By Nawshad Haque, Leanne Smith, Hal Aral, Joseph Cho, Warren Bruckard

"Water availability is one of the principal parameters in determining the feasibility of mining projects in arid and semi-arid regions. The volumetric water footprint (VWF) of a conceptual model of a copper flotation plant was found to be 2.45 kL/t Cu ore, compared with an actual measurement reported in the literature of 2.72 kL/t Cu ore. The flowsheet considered included mineral processing stages such as crushing, screening, grinding, classification, separation, flotation, thickening and filtration. The effect of a number of variables on the VWF was evaluated, including solid/liquid ratio, feed mass flowrate, ore loss, water loss, moisture content of ore, ore grade and water recycling. The use of seawater with recycling provided the most environmental and economic advantage among several scenarios evaluated. The study assumed a price of $1/kL freshwater, $4/kL for transport over a 200 km distance at 2,000 m altitude and $4/kL for water treatment. The water related cost of the desalinated seawater use scenario was A$493/t Cu concentrate, while the water related costs of fresh water and blended water scenarios were A$308/t and A$268/t Cu concentrate, respectively. The water related cost (fresh water scenario) accounted for 44% to 49% of the entire mining and processing costs that included drilling, blasting, loading, hauling, crushing, grinding and concentrating. The total overall cost was A$435/t Cu concentrate for the seawater with recycling, compared to A$451/t Cu concentrate for the fresh water with recycling case.INTRODUCTIONReducing the water footprint (WFP) by utilising alternative water sources has been a focus of mining projects due to increasing concerns about water scarcity and growing energy costs. The global mining industry can expect to experience fresh water shortages in the future, and saline or hyper-saline water may be the only available water source to process minerals in arid regions. Extensive studies on alternative water sources (e.g. seawater, desalinated seawater, blended water) and the reuse of process water have recently been conducted (Moreno, Aral, Cuevas, Monardes, Adaro, Norgate & Bruckard, 2011; Aral, Mead, Cuevas, Davey & Bruckard, 2010). Such studies provide sustainable and economic strategies for mines and concentrators in the arid or semi-arid regions of the world such as in Chile, Peru, Indonesia, and Portugal. More work, however, is needed to confirm water consumption data for different base metal flowsheets and use this data to develop water models that can lead to reduced WFPs and more sustainable water usage in the mining industry."

Jan 1, 2016