Search Documents

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By Alexander Levran

The main thrust of this presentation is to illustrate the growing contribution of solar energy to the mining industry by replacing existing mechanical and pneumatic tools and equipment with more effective and efficient electrical tools due to the increased efficiency and lower cost of solar energy generation. LCOE (levelized cost of energy/electricity) for solar energy is becoming highly competitive with other conventional sources of energy. The distributed architecture of solar power plants allows the supply of energy to highly remote and abandoned geographies. We will focus on the trend for this contribution to the mining industry over the next three years. Water desalination and delivery to the mining area will be topic of discussion regarding the contribution of solar systems in Latin America (LATAM) and other geographies. INTRODUCTION Increasing price pressure on the mining industry has generated a strong interest for mining companies to investigate energy costs and consumption. Currently, energy costs in mining economics contribute15% to 25% of the total commodity cost. In the past, most mines were operated by diesel gensets. Very high logistics costs for diesel supply, high and fluctuating diesel prices and theft led to very high energy prices. To overcome this problem, the mining industry has turned to solar energy, employing two main solutions: (i) adding a small scale (single level MWp energy supply) solar to an existing diesel system to create a hybrid solution operating as a microgrid environment; and (ii) replacing the existing diesel system with a large scale grid connected photovoltaic system financed by utilities or private IPP owners that signed a long-term power purchase agreement (“PPA”). In both applications, the near-term trend is to add storage and weather controls to optimize the electrical performance of the system. Use of concentrated solar solution (CSP) in the past was employed in a few remote sites to provide electrical energy to the mines. Currently this technology is not competitive with the photovoltaic (PV) systems. In some installations we have seen usage of a small hybrid system that is designed as relocatable, containerized and delivers scalable electrical power. In addition to the evolution of electrical energy sources, we see the trend of reduction of energy consumption in the mines by optimizing energy efficiency and generating load shifting solutions. Many studies of electrical energy in the mining industry support the growth of this trend in the mining industry.

Jan 1, 2019

By Dennis L. Murr, James E. Wennen

"The through-put and energy efficiency of an autogenous (AG) grinding mill are adversely affected by variability in rock size and rock competency. This applies to both fully autogenous and semi-autogenous (SAG) grinding circuits. In this paper we focus on an approach to overcome the problem of inconsistent mill through-put related to variability in mill feed size and rock competency. The focus is on ores containing hard, competent rock. This approach consists of preparing feed to an autogenous mill that contains 20% coarse media rock and 80% of material crushed to pass 37 mm. Results of pilot-scale testing for two iron-ores will be presented to show that a 10% to 12% reduction in unit energy consumption is possible with prepared feed, compared with feeding the mill with conventional primary crusher discharge.INTRODUCTIONIn the past 30 years or so, autogenous grinding and semi-autogenous grinding have been the comminution technologies of choice for most mining and mineral processing operations. These technologies saved both capital and operating expenses associated with the installation and operation of multi-stage crushing and screening plants required for conventional rod mill – ball mill circuits. However, SAG and AG are inherently inefficient in terms of energy consumption, especially for very hard ores. In cases of hard ore, changing characteristics of rock fed to the mills causes wide fluctuations in mill capacity, which contributes to the inefficiency. Rising electric power costs make this the most expensive unit operation used in the extraction of valuable minerals from an ore. The objective of the concept discussed here is to reduce the energy consumption in AG grinding for hard ore and eliminate the use of large-diameter steel grinding balls that are required for SAG grinding"

Jan 1, 2012

By Kyle Paulsen

The Cameco Key Lake mill began processing U-bearing waste rock from the McArthur River mine in 2000. This ore often contains elevated levels of calcium (>4% by mass), resulting in less than favourable conditions in parts of the Key Lake mill, yet still contains U3O8 at a concentration of about 0.3%. To recover the U3O8 and reject as much calcium as possible, modifications were made to the grinding circuit in late 2007 to include a gravity concentrator. The concentrator allows this mineralized waste to be processed separate from the regular blend material, rejecting calcium and concentrating U3O8, thus improving the operating conditions in areas such as SX. This will be presented in greater detail along with results and further work.

Aug 1, 2010

The Project ? $1.4 billion project ? 59,000 tonnes of nickel and cobalt ? Large resource base ? First production end of 2004 The Place ? Half the size of Vancouver Island ? Population 210,000 ? 43% Melanesian, 37% European, 12% other South Pacific groups, 8% other nationalities ? Tourism principal industry ? 1/3 of world?s nickel resources The Politics ? French Overseas Territory ?1998 Noumea Accord: increased local control over domestic policy ? Referendum on independence in 2014 ? Seeking more economic autonomy, less dependence on French support

May 1, 2002

Forward-Looking Statements Information set forth in this presentation may involve forward-looking statements under applicable securities laws. Forward looking statements are statements that relate to future, not past, events. In this context, forward-looking statements often address expected future business and financial performance, and often contain words such as "anticipate", "believe", "plan", "estimate", "expect", and "intend", statements that an action or event "may", "might", "could", "should", or "will" be taken or occur, or other similar expressions. Forward-looking statements or information relate to, among other things expected iron ore demand, timing for a production decision, expected share price drivers, potential railway options, timing, grade and quantity of potential resource estimates, employment and economic benefits, taxation estimates and timing of key project milestones. By their nature, forward-looking statements involve known and unknown risks, uncertainties and other factors which may cause our actual results, performance or achievements, or other future events, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. Such factors include, among others, the following risks: the risks associated with the need for additional financing; operational risks associated with exploration; fluctuations in commodity prices; title matters; environmental liability claims and insurance; reliance on key personnel and other risks and uncertainties discussed in the management discussion and analysis section of our interim and most recent annual financial statement or other reports and filings with the TSX Venture Exchange and applicable Canadian securities regulations. Forward-looking statements are made based on management's beliefs, estimates and opinions on the date that statements are made and the Company undertakes no obligation to update forward-looking statements if these beliefs, estimates and opinions or other circumstances should change, except as required by law. Investors are cautioned against attributing undue certainty to forward-looking statements. NI 43-101 Qualified Person Alderon?s exploration work on the Kami Project is supervised by Edward Lyons, P.Geo., the Chief Geologist for Alderon and a Qualified Person as defined byNational Instrument 43-101. Mr. Lyons has reviewed and is responsible for the technical information contained in this presentation. Mr. Lyons is a member in good standing of the Association of Professional Engineers and Geoscientists of British Columbia (APEGBC) and the Professional Engineers & Geoscientists Newfoundland & Labrador (PEGNL) as a registered Professional Geoscientist (P.Geo.).

May 1, 2011

By K. C. Sole

In most copper solvent-extraction operations, an important consideration in choice of extractant is the requirement for high selectivity of copper over iron. Ester-modified aldoxime extractants presently offer the best Cu:Fe selectivity. In some plants, however, the process feed liquors contain significant amounts of manganese but little iron. Although manganese is not chemically extracted by oximes, trace amounts are carried over to the electrowinning circuit by physical entrainment. This may result in anodic oxidation of manganese which, in turn, can cause oxidative degradation of the organic phase when returned to the solvent-extraction circuit in the spent electrolyte. Many of these operations prefer to operate with higher levels of iron reporting to the advance electrolyte, as appropriate control of the Fe(II)/Fe(III) couple will ensure that manganese remains in the benign Mn(II) form. A new reagent, LS 4202, designed by Cytec, now offers the possibility of tailoring the iron co-extraction, so that appropriate Cu:Fe selectivity can be achieved in the solvent-extraction operation to maintain an electrolyte Fe:Mn mass ratio of >10:1, while retaining the other benefits offered by ester-modified aldoximes. The results of an integrated solvent extraction-electrowinning pilot-plant trial are presented, in which the performances of the conventional extractants ACORGA® M.5774 and LIX® 984N are compared with LS 4202. The Cu:Fe selectivity is demonstrated, along with results on the transfer of other impurities to the advance electrolyte.

Jan 1, 2007

By S. Orr

In situ leaching is a complex, multidisciplinary process, which requires both mastering and integration of the different disciplines involved. Particularly, in-situ leaching is the intersection between geology (geochemistry, mineralogy, structural geology), hydrology (hydrogeology, well hydraulics), metallurgy (hydrometallurgy, electrochemistry, aqueous chemistry), and economics (mineable ore, cost of operations, market). The management of such a complex system requires all relevant knowledge base, integration, and continual optimization. Our presentation starts with a description of the "expert system" ? from data acquisition to information and knowledge, including determination of essential in-situ parameters, analyses, and modeling, which ultimately leads to an integrated, real-time, hierarchical management/control system.

Jan 1, 2007

This paper comprises a description of on-stream analysis instrumentation, including sample handling, X-ray optics and data processing. It also includes a discussion of some typical applications of an on-stream analyzer as related to the mineral processing industry. Introduction T WO automatic X-ray spectrometers have been developed for the simultaneous analysis of as many as six elements in a given sample. These instruments, namely the On-Stream Analyzer and the new Vacuum Simultaneous Spectrometer, have been designed specifically for process control in industry where large numbers of static samples or a number of flowing sample streams must be analyzed continuously with both speed and accuracy. This paper is concerned particularly with the application of these instruments for the continuous analysis of dynamic samples. The Instruments The On-Stream Analyzer and the Vacuum Simultaneous Spectrometer are intended to serve industry by offering two basic approaches to the problem of continuous sampling of flowing sample streams. The On-stream Analyzer (Figure 1) is designed for the completely automatic and unattended analysis of flowing sample streams in a programmed cycle of operation.

Jan 1, 1965

By Georges Houlachi, Akram Alfantazi, Maysam Mohammadi

Manganese ions in zinc electrowinning electrolytes form a protective MnO2 layer that ultimately decreases Pb contamination in the zinc product. In this study, the effect of dissolved Mn2+ on the electrochemical performance of Pb, Pb-Ca and composite Pb-MnO2 anodes was investigated. The properties of the MnO2 layer formed on these anodes were studied and compared. Potentiodynamic polarization and cyclic voltammetry experiments were performed in 180 g L-1 sulphuric acid to study the electrochemical reactions occurring on the anodes. The anodes were subjected to galvanostatic polarization at 50 mA cm-2. The morphology and uniformity of the MnO2 layer on the anodes were examined using scanning electron microscopy (SEM). Experimental results revealed that the MnO2 layer formed on the composite anode was more compact and uniform compared to that formed on the Pb and Pb-Ca anode. It was also observed that the cell mud formation rate, and consequently manganese ions consumption, depended on the anode type. Although initial formation of the MnO2 layer decreased the oxygen evolution overpotential, its growth might negatively affect electrocatalytic activity of the anodes.

Jan 1, 2014

"Abstract - An estimation of resources of structurally complex gold lodes and stockworks represents a challenging task for geoscientists due to the complex geometry of the lodes and discontinuous grade. In the present case study, the resource of a gold stockwork has been estimated by uniform conditioning after the lode has been subdivided into geostatistically defined domains using the indicator probability model. The indicator probability model represents a powerful tool for structural interpretation of the mineralization and can be applied when traditional 3D volume constraining methods (wireframing) have failed to produce a unique, non-subjective model. For comparison, the resources of the same zone have been estimated without domaining. Results of the study clearly show that estimates obtained without domaining of the mineralization can yield a substantial error due to excessive smoothing of the grade.Application of uniform conditioning for modelling the grade distribution has a significant advantage over linear methods (e.g., ordinary kriging). Uniform conditioning enables estimation of local recoverable resources at different selective mining unit sizes that can be substantially smaller than the drilling density without creation of biases or over smoothed local values."

Jan 1, 2002

By H. M. Woodrooffe

This paper deals with the laboratory facilities at the Mines Branch for carrying out research in the industrial minerals field, and also reviews current programs in ceramics and construction materials, in non-metallic minerals and in the milling of industrial minerals. It then discusses the application of these pro-grams to industrial problems.

Jan 1, 1967

By W. D. Robbson

DR. G. W. RAMSEY (l): A study of our non-treatment silicosis autopsy material for the years 1940-43 inclusive, in addition to the common findings of fibrosis, nodules, and emphysema, shows marked thickening of the alveolar walls. This change is due to one or more of the following factors: congestion, edema, accumulation of both small and large monocuclear cells within the interstitial tissues and large monocuclear cells attached to the lining membrane of the alveolar sacs. This alteration in the alveolar walls, we believe, is one of the most important factors in producing impaired pulmonary function. Comparison of our first autopsy material of a case receiving twenty aluminium treatments beginning June, 1943, shows a striking change in the alveolar walls. In all areas free of silocotic nodules and fibrous tissue, the alveolar walls approach normal thickness and are free of cellular deposits. No change was noted in the old processes and none was expected. We believe that these changes in the alveolar walls were brought about by the aluminium therapy and that they constitute a major factor in the improved pulmonary ventilation noted in treatment cases.

Jan 1, 1945

"With the globalization of the mining industry, many companies are now seeking to invest in underground diamond mines, with the purchase of small diamond pipes being seen as particularly attractive. However, recent experiences in South Africa have shown that many projects fail due to a lack of awareness of the hazards associated with diamond mining. In this paper three significant hazards are dealt with — mud rushes, block crushing, and implementation of an inappropriate mining method. Measures that assist in the prevention of these three hazards are given.IntroductionFor over a hundred years, South Africa has been seen as the centre of the diamond mining industry, possibly having the largest number of operational underground diamond mines in the world. Despite the fact that this industry has been dominated by large mines of De Beers Consolidated Mines Limited, many small underground mines have operated profitably for a number of years, exploiting diamondiferous fissures and pipes. In the last decade there has been renewed interest in these small operations from international companies. However, many of these projects have not realized their full potential owing to a lack of appreciation of the hazards inherent in the operation of a diamond mine.Hazards Associated with Diamond MiningIn the development of a diamond mine, the mining company must be aware of the hazards associated with diamond mining. There are three main hazards: (1) mud rushes; (2) block crushing; and (3) selection of an inappropriate mining method (not a natural hazard, but a planning induced hazard). Each of these hazards will be dealt with in turn in the following sections."

Jan 1, 2000

By C. A. Lorenson

THE Marmoraton mine is located a mile southeast of Marmora, a village in Hastings county, Ontario, 130 miles east from Toronto and 143 miles west of Ottawa. Highway No. 14 from Belleville intersects Highway No. 7 at Marmora and the branch line of the Canadian National railway between Trenton and Bancroft passes through the property just east of the open pit. HISTORY AND GEOLOGY The Marmora orebody appears as the whorls of a thumb print on the aeromagnetic survey map released by the Ontario Department of Min.es early in 1950, the survey of the district having been made in 1948 and 1949, under the joint auspices of the Department of Mines and the Geological Survey of Canada. The 'anomaly' appeared to have interesting possibilities, so Bethlehem representatives carried out a ground survey and began drilling the property in June, 1950. A total of 40 holes, aggregating 37,000 feet, were drilled to delineate the ore-body. The Marmora orebody is a re-placement of Precambrian limesto.ne with zones or bands of magnetite interlaid with metamorpl1ic rocks and cut by later intrusives. The ore and associated Precambrian rocks are overlain by 100 to 150 feet of flat-lying Palaeozoic limestone. It is a low-grade deposit averaging 33 per cent iron and requires concentration to raise it to 65 per cent iron grade.

Jan 1, 1958

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

By G. M. Behrend

"The mining and processing of mineral ores is a very old industry which is steeped in tradition. Rising demand for metals has recently forced the exploitation of lower-grade orebodies which require extensive beneficiation. The high capital expenditures involved, together with market pressures for high-quality concentrates and pellets, have forced the development of new process technologies which are heavily dependent on automatic process control. Development of suitable instrumentation has been rapid and it is being applied to mining processes today with a high degree of sophistication. The drive for higher efficiency and profitability goes on and has reached a level at which modern digital computers appear to be the only answer. However, the efficient application of a digital process computer is extremely complicated and is therefore approached by the mining industry with considerable hesitation.Some of the benefits promised by the digital computer can be obtained today by other means, which are more manageable and can provide immediate payoff. The result would be a building-block system which would utilize the digital process computer as its final component, to perform true plant optimization, free from routine chores."

Jan 1, 1971

By L. E. Djingheuzian

ANON-CATARACTING (N-C) ball mill is so operated that the balls are not thrown in-ward at the top of their paths. The result is to maintain, in the mill, a quiescent pool in which classification will occur at a limiting size corresponding to the pulp density. N-C operation is produced by effecting proper relationship among mill speed, ball diameter, volume of ball load, and pulp density. Such operation is typified by the primary ball-mill operation of the Tennessee Copper Company, Copper-hill, Tenn., and the Cleveland Cliff Iron Company, near Ishpeming, Mich.

Jan 1, 1958

By David G. Baskin

"THIS DEPARTMENT is unique in that it operates in the production stream and also provides an essential service. Its operating function consists of scheduling an ore train to haul 10,000 tons per day over 17.1 miles of track and switching all incoming and outgoing rail equipment on 2.2 miles of track at the minesite and 6.2 miles of track at the metallurgical site. The service it provides is traffic control of all incoming commodities and all outgoing concentrates, metals and acid by rail and truck, even extending to port and ship control for overseas shipments (Fig. 46). Although they cover many miles, the railroad and traffic department employees operate very efficiently, as indicated by the following organizational chart:Railroad and Traffic Superintendent ................ 1Railroad Supervisor .............................................. 1Assistant Railroad Supervisor ........................ 1Track Foreman ...................................................... 1Trainmen ............................................................... ... 4Switchmen ............................................................... 4Trackmen ................................................................ 10Traffic Supervisor ................................................ 1Clerk Steno ............................................................ 1Clerks ...................................................................... 3"

Jan 1, 1974

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018