Search Documents

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By Robert B. Parsons

"As the 1981 annual reports of Canadian mining companies one by one see the light of day, it becomes clear that softer metal prices and rising costs are the main problems which beset the industry today. These problems are certainly not lightened by that familiar monster lurking in the shadows-taxation! Recent taxation trends in Canada, and the existing tax regimes for the mining industry, continue to be a major bugaboo.This examination by ""Tax Notes"" of the impact of current taxation trends on the mining industry is based on a speech delivered recently by Robert D. Brown, senior tax partner of Price Waterhouse, Canada, to the annual meeting of the American Institute of Mining, Metallurgical and Petroleum Engineers in Dallas.IntroductionThe purpose of this paper is to tell a story-and it is a story with a moral. The first thing to recognize is that, with depressed metal prices and weakening western economies, high taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. However, the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what the future holds for mining men in Canada will equally play an important role in the future development of the Canadian industry. Our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high marginal tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself."

Jan 1, 1982

By Bétournay. M. C.

Advantages ?Safety ?Health ?Rapid, continuous development, productivity ?Stope dilution reduction Disadvantages ?High cost and long time for equipment development ?Hard rock mining condition limitations ?Size of equipment ?Equipment set-up time, down time ?Performance does not meet financial return targets ?Drill and blast retains advantage in cost, productivity, capital investment, application flexibility ?Stress accumulation issues in deep mining, ground support and material handling issues in weaker rock

May 1, 2009

By J. R. Tickner

"Gold is conventionally analyzed using fire-assay or other destructive chemical methods that impose significant sample preparation, OH&S, and skilled labour requirements. Developed over the past 15 years by the CSIRO, PhotonAssay provides a new approach. A high intensity, high-energy x-ray source is used to activate atoms of gold and other elements in bulk mineral samples. The resulting activity is counted to automatically, accurately and rapidly determine metal grade. Samples weighing 0.5–1.0 kg can be measured in a few minutes with minimal preparation. As the method is matrix-agnostic, traditionally hard-to-assay materials such as highly refractory ores, carbon pulps and copper concentrates require no special treatment. We present the status of commercial PhotonAssay systems being developed by Chrysos Corporation. The first unit with a throughput of up to 80 samples per hour is to be deployed in an Australian assay laboratory in late 2017; smaller systems suitable for providing real-time assay directly at the mine-site will be progressively rolled out from mid-2018. Performance results from extensive testing using both mine-sourced and standard reference materials are presented, demonstrating the sensitivity and accuracy of the method. Implications for replacing conventional gold assay in exploration, mining and processing operations are discussed.INTRODUCTION Accurate methods for assaying ore grade are essential throughout the exploration, mining and mineral processing value chain. The discovery and evaluation of new ore deposits, reserve and resource definition, mine operations planning, ore processing, metal accounting and product quality evaluation all rely on accurate measurement of the valuable metal content of bulk materials. The analysis of gold presents particular challenges, stemming from the very low concentrations at which commercial operations run (often part-per-million (ppm), or equivalently one gram-per-tonne levels or below), and the highly heterogeneous nature of many gold deposits. These challenges mean that any analytical method must have high sensitivity and be capable of measuring large-mass samples. The most widely used quantitative analytical method for gold is fire-assay (Hoffman, Clark and Yeager 1998). An initial ore sample typically weighing several kilograms is dried, crushed and pulverized to allow a small sub-sample (10–50 g is common) to be representatively drawn. The sub-sample is mixed with flux, litharge (lead oxide), a reducing compound and other reagents. The mixture is fired at a temperature of 1000–1200°C until molten. After cooling, the slag is removed and the lead button containing any gold present in the sample is remelted in a porous cupel. The lead is absorbed into the cupel, leaving a gold prill which is either weighed directly, or dissolved in acid and analysed via atomic absorption spectroscopy (AAS) or inductively coupled plasma spectroscopy (ICP or ICP/MS)."

Jan 1, 2017

By C. Y. Lim, H. W. Kim, M. S. Kim, J. H. Cho, Y. S. Lee

Al - 5.5 wt% Mg - 0.3 wt% Cu alloy strip was successfully fabricated by horizontal-type twinroll casting (TRC). For producing sound strips with no surface defect, the casting was conducted at various roll rotation speed, and the sound strip could be obtained at relatively low casting speed (3 rpm). The cast strip was homogenized at 450 °C for 10 hours, and then cold rolled with a reduction rate of 78%, followed by a final annealing at 450 °C for 1 hour. The annealed sheets showed good mechanical properties with approximately 330 MPa in tensile strength and 27 % in elongation, but exhibited strong anisotropy depending on the tensile directions. For the homogenized sheets, warm rolling was also conducted at 200, 300, and 400 °C. The tensile test results of the warm-rolled sheets showed that the rolling at medium temperature (300 °C) was proper to fabricate the sheets with relatively good mechanical properties and low anisotropy.

Jan 1, 2014

By A. Khodadadi, M. Abdolahi, P. Taimory

Cyanide is used by the mining and chemical industries in tremendous quantities without attention being given to its hazardous properties. The use of cyanide compounds in mining is one of the most important environmental issues for the mining industry due to the acutely toxic properties of many cyanide compounds to humans and aquatic life. Cyanide tends to react readily with most other chemical elements, producing a wide variety of toxic, cyanide-related compounds and because cyanide is carbon based an organic compound it reacts readily with other carbon-based matter, including living organisms. This research is aimed at investigating a feasible and economical technique for the removal of cyanide from tailing wastewater of Muteh gold mine. In this research, removal from Muteh factory's waste water, was achieved at Tarbiat Modares University's mineral processing laboratory through the oxidation of cyanide by calcium hypochlorite. Cyanide oxidizes and changes to cyanide (CNO-) which is 1000 times less environmentally hazards than cyanide. Cyanide titration was accomplished using Rhodanine solution and silver Nitrate. Cyanide concentration in the wastewater, was 270 mg/L. Cyanide removal was achieved at an optimum pH of 12.3. However, at higher temperatures, cyanide removal was complete at this pH level. Optimum Dosage for complete removal of cyanide using calcium hypochlorite was 1.43g/L.

Jan 1, 2005

By Marcel Vallée

"Abstract-In recent years, several unsavory events in international mineral exploration, as well as several widely publicized project difficulties and failures have occurred. The report Setting New Standards has "raised the bar" and proclaimed a "commitment to continuous improvement... and change." We need to evolve from our "generally accepted" practices to more effective quality assurance policies, guidelines and standards. Several steps will be required to support the work of the "qualified persons" now wholly entrusted with technical and professional matters:• adopt a mineral development model and objectives appropriate to orient the selection of workmethods and verification procedures suitable to increase the profitability of these activities;• review the definitions and implications of the terms practice, guideline and standard;• review three quality assurance systems with emphasis on commitment of company management and complementary emphasis on systematic quality policies, plans and manuals (ISO 9000), continuous improvement through "profound knowledge" (Deming, 1986), and self-appraisal of continuous improvement and client satisfaction using the Qualimeter Guide (Québec Society for Quality);• determine, from the objectives of the mineral development model proposed and the problems often encountered, the requirements of resource/reserve estimation and the production feasibility study. To regain investors’ confidence and improve the returns from mineral development activities, an explicit commitment to quality by the board of directors and the management of every company is required.A number of mining companies have gained ISO 9002 certification for their operations but exploration companies should start by developing and implementing quality assurance guidelines and standards based on the ISO 9001 pattern, without achieving actual ISO certification in the short term. Both professional associations and industry organizations must be involved in the process of developing the required quality and continuous improvement guidelines and standards."

Jan 1, 1998

By V. V. Pankov, W. R. Chen, L. R. Zhao

Diffusion nickel aluminide and overlay NiCrAlY coatings were deposited on single crystal Ni-base superalloy CMSX-4 substrate using the chemical vapour deposition and cathodic arc evaporation techniques, respectively. The NiCrAlY coating underwent a post-deposition heat treatment in an argon atmosphere at 1100°C for 2 hours. All the coated specimens were subjected to furnace cyclic oxidation testing at 1000°C up to 1500 one-hour cycles. The morphology, elemental composition and phase constituents of the oxide scales formed on the coating surface were analyzed using scanning electron microscopy, energy-dispersive spectroscopy and X-ray diffraction. It was observed that the diffusion aluminide coating experienced accelerated weight gain at an early stage of the test (150-400 cycles), whereas the overlay NiCrAlY coating fabricated by cathodic arc evaporation maintained steady-state weight gain throughout the entire 1500 cycle test duration. This difference in oxidation behaviour between the two types of coatings is attributed to the early development of nickel-aluminum spinel on the surface of the diffusion aluminide coating, in contrast to the stable aluminum oxide scale formed on the overlay NiCrAlY coating during cyclic oxidation testing.

Jan 1, 2015

By J. Olsson

The paper describes and discusses the use of stainless steels for leaching plants emphasising the duplex family, i.e., austenitic-ferritic stainless steels. This group has generally twice the proof strength of the more common 300-series austenitic grades, which implies possibilities to reduce the gauge at construction of pressure vessels and atmospheric tanks and vessels and thereby possibilities to reduce the weight. The duplex grades have also higher surface hardness resulting in better resistance to mechanical wear, i.e., abrasion and erosion corrosion. The lower contents of nickel and molybdenum imply lower cost and a more stable price considering the present market situation for these alloying elements. Corrosion data from laboratory and pilot plant tests, as well as examples of applications of duplex and highly alloyed austenitic grades, are presented. Cu2007 - Volume IV (Book 1) The John E. Dutrizac International Symposium on Copper Hydrometallurgy Edited by P.A. Riveros, D.G. Dixon, D.B. Dreisinger, M.J. Collins Toronto, Canada,

Jan 1, 2007

By K. N. Karparov

?Two highwall failures in a South African coal mine defied analysis by widely accepted limit equilibrium methods. ?The geological conditions were complex, with undulating coal-bearing strata overlying a karstic topography formed in underlying dolomite belonging to the Transvaal Supergroup. ?It was clear that the simplifying assumptions made by all limit equilibrium methods were inappropriate in the conditions.

May 1, 2007

By J. Worden, D. Hughes, S. Smart, H. Zughbi

The enterprise wide optimization (EWO) of steelmaking and manufacturing is a multi-level, hierarchical problem which spans higher level corporate planning and scheduling through to the lower level operations of processes that produce and manufacture steel. External and internal system dynamics combined with process unit co-ordination create complex changing circumstances for the enterprise. This paper presents a scoping study as a prelude to enterprise wide considerations at an integrated steelworks to help inform the choice of appropriate model types and optimization techniques. The hierarchical, multi-level structure of the enterprise and the important spatial-temporal scales to consider are defined. Insights into the system were gained by analyzing a large set of dynamic operational data. Over two years of data were subject to both univariate and multivariate analysis with the intent of understanding the complex interrelations of energy flows on site, the inherent system dynamics of the energy network, system operational modes, aspects of planning and scheduling and the coordination between major processing units. This analysis was further used to evaluate the performance of the system in regards to energy utilization and understand the potential economic benefits derived from improved operational decisions.

Jan 1, 2015

By Feng Xue, Mi Xujun, Peng Lijun, Yin Xiangqian, Liu Dongmei, Xie Haofeng, Huang Guojie, Yang Zhen

The Age-hardening Cu-Cr alloys are extensively used in integrated circuit lead frame, railway contact wire, resistance welding electrode and continuous casting mold copper plate, owing to having an excellent combination of high electrical or thermal conductivity and high strength. High temperature performance is very important during the service process. Effect of Magnesium and Zirconium on softening behavior of Cr-Cr alloy are investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). During the softening process in the Cu-Cr alloy, the recrystallization process, grain growth and Cr precipitates coarsening are observed. The addition of Mg or Zr to the Cu-Cr alloy, the resistance to elevated temperature can be significantly improved, owing to being restrained the growth of the precipitates by segregating along precipitates surface. INTRODUCTION Age-hardening Cu-Cr system alloys can be widely uesed in many fileds such as electrodes for spot welding (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012), intergrated circuit lead frame (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003; Cheng, Yu & Shen, 2014; Zhang et al., 2016; Li et al., 2007) and railway contact wire (Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003), because it has high strength, good electrical and thermal conductivity. The precipitation behavior of binary or ternary Cu-Cr alloys had been investigated by many researchers (Chbihi, Sauvage & Blavette, 2012; Peng et al., 2017; Batra et al., 2002). In addition, to obtain additional mechanical properties without much deterioration in electrical conductivity, trace addition of alloying elements like Zr, Ag, rare metals (Y and Ce) and Mg are added into Cu-Cr alloy. The addition Mg to Cu-Cr alloy accelerated the process of precipitates nucleation and restrained the growth of the precipitates by segregating along precipitates surface during aging, which enhanced the stability of the deformation microstructure and improved the mechanical properties of the alloy (Zhao et al., 2018). Additional zirconium in Cu-Cr alloy enhances the strength by the decrease in inter-precipitate spacing of Cr precipitates and the formation of Cu5Zr phase (Chihiro, Ryoichi & Kazue, 2008). Owing to the decrease in inter-precipitation spacing of Cr precipitates and to the Ag-atom-drag effect on dislocation motion, the addition of Ag can increase in strength, stress relaxation resistance and without much deterioration in electrical conductivity (Chihiro, Ryoichi & Kazue, 2008). The enhance in strength and electrical conductivity of the Cu-Cr-Zr alloy by adding Ce and Y elements are attributed to removing oxygen and sulfur from as-cast alloy (Li et al., 2006). However, the effect of Mg or Zr element on microstructure and properties of Cu-Cr alloy during the softening process are not clear. Therefore, Microstructure evolution and properties of a Cu-Cr systems alloy were investigated in detail by OM and TEM. The Relationship between microstructure and properties of Cu-Cr systems alloy was also discussed.

Jan 1, 2019

By Shoma Sinha, Nirmal K. Sinha

Deformation in a material at any temperature is known to consist of two major components - a reversible (elastic) part and an irreversible part (often called plastic). What is not universally known is the fact that at high temperatures greater than about 0.4Tm, where Tm, is the melting point in Kelvin, the reversible part includes not only elastic but also a delayed elastic (recoverable but time dependent) component. A very simple computational model is presented here for a constant-strain stress relaxation test (SRT) on the basis of a three-component constant-stress rheological equation derived from strain relaxation and recovery test (SRRT) data. It is shown that the rapid stress reduction during the early periods of relaxation when the stresses are high is governed primarily by delayed elasticity irrespective of the imposed strain level. This is in contradiction to the popular concept prevailing today. The asymptotic approach to a quasi-stable stress rate at longer times and lower stresses is, however, controlled by viscous flow (power-law creep). The validity of the theory is examined by comparing the predictions with experimental results obtained for a titanium-base alloy Ti-6246 at 0.45Tm.

Jan 1, 2004

By J. M. Menacho

As usually occurs in technological development, heap leaching knowledge has been built upon two parallel lanes, theory developed on fundamentals but relatively far from industrial applications, and operational know-how generated from empirical trial and error. As a contribution to close the gap between the above-mentioned lanes, the De Re Metallica process consulting group has been developing and applying fundamentalsbased modeling tools for industrial process design and process optimization of existing plants over the last ten years. As result, a library of models is now available with application to the whole production chain from blasting to electro winning. This presentation is centered in heap leaching and several real case studies are developed, showing how paradigms are broken when fundamentals are applied. Cu2007 - Volume IV (Book 1) The John E. Dutrizac International Symposium on Copper Hydrometallurgy Edited by P.A. Riveros, D.G. Dixon, D.B. Dreisinger, M.J. Collins Toronto, Canada,

Jan 1, 2007

By P. M. STILES

Acquired in 1957, the limestone quarry of Ideal Basic Industries on Texada Island north of Vancouver has become a major supplier of high purity limestone and construction stone. Crushed limestone products are shipped by barge to various destinations along the B.C. and northern U.S. coasts.

Jan 1, 1984

By M. Kawata, T. Amano, T. Miyamoto, K. Shibayama

"The High Pressure Acid Leach (HPAL) plant of Taganito HPAL Nickel Corporation (THPAL), located in Taganito, Philippines, with a nameplate capacity of 30,000 Ni-t/year started commercial operation on October 2013. The plant load was smoothly ramped up and it achieved monthly production equivalent to 33,000 Ni-t/year in 2016. Partial improvement of the plant capacity for the achievement of 36,000 Ni-t/year, as evaluated from the current operation progress of each system is planned for 2017. In this paper, aside from presenting the progress of the plant ramp-up, research and development activities such as the reduction of nickel loss and the improvement of filtration capacity which was achieved by particle size control of ZnS precipitates in the Zinc Removal system are also discussed.INTRODUCTION Taganito HPAL Plant Project History of THPAL Taganito HPAL Nickel Corporation (THPAL) was incorporated in August 2008, as a joint venture of three (3) companies, namely Mitsui Corporation with 15% share, Nickel Asia Corporation (NAC) with 10% share and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 75%. Aside from its capital share, NAC’s Taganito Mining Corporation (TMC) supplies the ore for the HPAL plant located in Taganito, Claver, Mindanao, Philippines. The objective of THPAL is to produce 30,000 MT of nickel and 2,600 MT of cobalt as mixed (Ni/Co) sulfide by treating nickel laterite ore in the Philippines and exporting to Japan as raw material for SMM’s Niihama Nickel Refinery (NNR) for the next 30 years. In other words, 1.15 wt% of nickel in ore is refined to 99.99 wt% nickel in electrolytic nickel. The mixed (Ni/Co) sulfide is shipped to NNR and SMM provides the technology and management personnel to THPAL plant as well as sulfuric acid which is the main reagent for HPAL process. Figure 1 shows the location of THPAL and current relationship between the stake holders.The Characteristics of THPAL Plant In terms of plant design, a 2-train system is applied for the HPAL circuit considering the reliability of the process, facility and avoidance of whole plant shutdown due to HPAL troubles. The technical data, operation know-how and improvements gained from the successful operation of Coral Bay Nickel Corporation (CBNC) which was established in April 2002 were reflected in THPAL’s plant design. As for the H2S plant, a more economical design was considered which is different from CBNC."

Jan 1, 2017

By G. Granata, C. Tokoro, T. Kato

"The goal of this study was to evaluate the effectiveness of mechanochemical activation by planetary milling as method to enhance the recovery of cerium from rare earth ores. For this purpose, a weathered ore was first ground by planetary milling and then leached by sulfuric acid. The influence of planetary milling was investigated by assisting the experiments with X-ray absorption fine structure (XAFS) in cerium LIII-edge and inductively coupled plasma spectrometry to measure the concentration of cerium dissolved by leaching. Results showed that, by increasing the grinding time, although the particle size of the specimen increased due to agglomeration, the recovery of cerium significantly increased. This finding clearly indicated that a smaller particle size actually hinders the recovery of cerium. In particular, XAFS analysis revealed that the longer the grinding time, the more tetravalent cerium could be converted into trivalent cerium and such conversion, also called mechanochemical reaction was beneficial to the recovery of cerium. Based on the obtained results, it was confirmed that approximately 70% of cerium could be recovered by mechanochemically activated leaching of rare earth ores.INTRODUCTION Rare earth elements (REEs) are a group of 17 chemically similar metallic elements comprising lanthanides, scandium and yttrium. Since REEs have various unique physical and/or chemical properties, they have become essential materials for advanced application (Adachi, 2015). REEs used in industry are usually supplied as rare earth minerals. In the last decades, flotation, gravity separation, magnetic separation and leaching have been widely applied to recovery of REEs from rare earth minerals like monazite (Archana, Rekha, Manis, Jitendra, & Jin, 2015). Among these operations, leaching has been widely studied in the recent years to improve the state of the art (Archana, Rekha, Manis, Jitendra, & Jin, 2015; Xiao, Feng, Huang, Huang, Chen, Liu, Wang, & Long, 2016; Farzaneh, Fereshteh, & Ahmad, 2017). Aiming to enhance recovery of REEs from rare earth minerals, a possible advancement of leaching technology could be the mechanochemically activation of the ore by high-intensity milling (Alorro, 2016). In the mechanochemical activation, an improvement of the leaching performances can be achieved through high-intensity milling operations which result into a dramatic decrease of the mineral particle size with a consequent improvement of the physical kinetics of leaching. Furthermore, the high mechanical energy provided to the sample during milling can determine the rupture of the crystal structure of the mineral, thereby transforming it into a more leachable form."

Jan 1, 2017

By G. Viramontes-Gamboa

Approximately 70% of world copper reserves consist of the mineral chalcopyrite, and much international effort has focused on its study. Ultimate objectives include the development of environmentally friendly alternatives to smelting, and technologies to treat low-grade ores, for which concentration and smelting are economically unviable. Unfortunately, chalcopyrite leaching is inefficient in H2S04-Fe2(S04)3-FeS04 solutions, which is considered to be the most desirable oxidizing medium for leaching of copper sulfides, since the chemistry is well known, corrosion of industrial equipment is negligible, subsequent copper recovery by SXlEW is well established, and environmental impact is minimal. The main reason for this inefficiency is the self-passivation of chalcopyrite. We have devoted considerable effort in the understanding of this phenomenon, and have developed a predictive electrochemical methodology capable of establishing a priori the precise range of potentials within which chalcopyrite leaches and where it is passivated. Since potential control is a critical parameter in chalcopyrite leaching, this experimental methodology can be very useful for establishing the best conditions to leach chalcopyrite. In this paper, the scientific foundations of this predictive experimental technique are presented, and its practical application is demonstrated by comparing its predictions with leaching experiments from the literature.

Jan 1, 2007

By N Berkowitz

Slurry pipelining, as now under-stood and practised, can only command marginal interest in Canada, as long-distance railway freight charges in this country are generally lower than slurry pipeline tariffs. Several alternatives to conventional slurry transmission are, however, now emerging, and two such alternatives are briefly discussed with reference to coal pipelining. In one, coal is transported as a suspension in oil; the other contemplates the movement of paste "slugs." Preliminary economic estimates indicate that the resulant process simplification and adoption of common carrier principles could lead to cost reductions that might make Western coal competitive with imported fuel in the power generating stations of eastern Canada. R ECENT appraisals of slurry pipelining techniques, some-what incongruously 'based upon the performance of successful installations (1,2), are making it increasingly apparent that current solids pipelining methods can only command marginal interest as methods of bulk commodity transportation (3). Although some uncertainties remain in matters of detail, it is now generally conceded that long-distance slurry pipelining cannot compete against rationalized railway transportation unless movement of

Jan 1, 1963

By S. M. Chentouf, M. Jahazi, N. Bombardier, T. Belhadj

The main limiting factor in the commercial expansion of superplastic forming (SPF) of thin sheet aluminum alloys is the extent of cavitation phenomenon that takes place during the processing. The severity of the cavitation process is mainly dependent on the uniformity of deformation (i.e. level of local thinning) during processing. In the present paper, correlations are made between thickness variations in several formed sheets and the characteristics of the cavities observed in the material. The 1.4 mm thick 5083 aluminum alloy sheets were hot pre-formed at around 450°C for 4 min and then air-cooled. Opto-digital and Scanning Electron Microscopy were used to examine the microstructure and analyse the cavities. Also, grain size measurements were carried out for different location in the SPF formed piece. The surface and volume fractions of the cavities were measured with the aid of metallography image processing (MIPTM) on as-polished samples prior to etching. The results are analyzed in terms of the influence of applied strain and microstructure conditions on the propensity to cavitation of the alloy.

Jan 1, 2015