Search Documents

"This contribution is concerned with adaptive processing decisions, where the process parameters are optimally adapted to the varying properties of the material input stream. Our starting point is the geometallurgical paradigm that the varying properties of the input stream are considered known e.g. from a geometallurgical model of the mined ore body, and optimal processing parameters are computed from them, by finding the parameter seaming optimal in a computer simulation.This approach however has to work with a lot of uncertainties: The prediction of the geometallurgical ore parameters can only be done with some geostatistical uncertainty. The parameters themselves are only proxies for true ore properties. Model prediction can differ relevantly from actual process results, due to model simplifications. Due to these uncertainties the computed processing choices can turn out to be inferior to simple non-adaptive processing. In this contribution we focus on the uncertainty of the ore properties and analyse this effect systematically, by modelling this uncertainty effect mathematically and in computer simulations. The most important findings are:(a) Processing choices not taking into account the uncertainty sometimes even perform worse than simple non-adaptive processing, for the sole reason of ignoring the uncertainty effect.(b) Ore properties, not adequately reflected in the ore description, might require different approaches, in which the observed processing behaviour feeds back into process control.(c) Bayesian decision theory allows computing optimal processing choices combining the information from the mine (geostatistical predictions) and from the process feedback. These choices give much more robust choices and do not suffer from the drawbacks described for the simple approach we started from.These new approaches can substantially improve the performance of adaptive processing in existing plants."

Jan 1, 2016

By E. Heikkinen, J. Suikkanen, T. Siren, J. Valli, M. Hakala

Diametrically faced borehole breakout observations are a fairly good indication of magnitude of the secondary stresses acting perpendicular to the borehole. In cases of low in situ stresses, where borehole breakouts are not observed naturally, it is possible to increase the prevailing stress state around the borehole by increasing the rock temperature. When the temperature is increased sufficiently, thermally induced borehole breakouts will occur. By implementing the temperature increase in boreholes located at excavated tunnels, it is also possible to study the effect of the near-field stresses caused by the excavation. The near-field stress state changes as a function of borehole depth, thus increasing the information available from experiment. To study the feasibility of this proposed low cost method, a Borehole Thermal Spalling (BTS) experiment was executed in ONKALO Underground Rock Characterization Facility, in Western Finland in 2014. The first borehole pilot test with the method was conducted in ONKALO at the POSE niche in already at May 2010, with the second pilot test following in August 2010 at Äspö HRL. The major objective of the experiments was to define the trend of the maximum in situ stress component, while also providing knowledge of the in situ spalling strength of the ONKALO rock mass. The stress state in ONKALO is nearly isotropic in horizontal layer, causing problems for the use of more traditional stress measurement methods. With boreholes heated over long interval, the weakest rock parts are observed to fail, thus providing statistical confidence. For these reasons, continuous test sections have an advantage in ONKALO, compared to spatially limited stress measurement methods such as overcoring and hydraulic fracturing. The BTS experiment is conducted in 9 meter deep vertical boreholes located at the POSE niche, situated -345 m depth below the ground surface. The boreholes used within the BTS experiment are located in migmatitic granite, in an experiment area where the surrounding stress state and the rock strength are fairly well known. The prior knowledge of the stresses is favourable for the experiment, as it requires careful planning and iterations to determine the appropriate heating power domain. Too low heating power will not be sufficient to cause borehole breakout, while too high heating power causes breakout in all directions thus making determination of stress direction hard or impossible. The initial state of the borehole and induced borehole breakouts will be monitored using acoustic televiewer logging (ABI) and optical borehole logging (OBI) imaging techniques. Fracture mechanics modelling is used in planning of the experiment, also in back-analysis to link the observed breakout angle to stress state. Both the pilot test in 2010 and BTS test in 2014 resulted in similar borehole breakout direction. The results are in line with so called EDZ & VT1 stress interpretation, revealed the maximum horizontal component bearing the magnitude of 21.5 MPa, with the trend of 166°.

Jan 1, 2015

By Troy Boisjoli, Sean Hillacre, Matt Batty

Discovered in 2014, the Arrow Uranium Deposit has undergone rapid development through successive drilling programs informed by geostatistical drill hole spacing studies. An independent third-party geostatistical drill hole spacing study was completed by Clayton V. Deutsch Consultants Inc. in 2017, evaluating the uncertainty of thickness, grade, density, and areal limit of the Arrow Deposit to determine a drill hole spacing suitable for Indicated Mineral Resources. Indicated spacing was defined to be 24 to 32 metres (“m”) to be within 15% of predicted for a nominal quarterly production volume with a probabilistic tolerance between 75 and 90%. The study not only defined the Indicated Mineral Resource resultant from the 2016 drill program, but also provided drill hole targeting criteria for subsequent drill programs aiming to convert Inferred to Indicated Mineral Resources. A subsequent geostatistical drill hole spacing study on the Arrow Deposit was completed by Clayton V. Deutsch with Resource Modeling Solutions in December 2018 to define Measured Mineral Resource spacing in support of the 2019 drill campaign. The study resulted in a drill hole spacing of 9 to 17 m to be within 15% of predicted for monthly and quarterly production volumes using an accepted industry probabilistic tolerance of 90%.

Jan 1, 2020

By Gérald Riverin, Bernard Boily, Daniel Bernard

"The Donalda gold deposit is located in the southern part of the Noranda camp, approximately 2 /em east of the Horne deposit. Combined past production and current reserves total over 1.5 Mt grading 6.9 grams of gold per tonne.The deposit consists of two main veins which are both narrow but persistent structures. The No 1 Vein, hosting about 80% of the gold ore, consists of an EW-striking banded quartz vein dipping on average 25° to the south. Although variable in thickness, it averages lessthan1 metre. TheNo2 Vein, located 300 m below the No 1 Vein, is similar to it except that it dips 50° south. Gold occurs mostly as fine native gold disseminated in quartz, with 2-3% pyrite and trace amounts of various sulphides and tellurides. The wall rocks are only weakly altered and mineralized with pyrite, hematite and sericite.Structurally, the Donalda deposit is centered on the Horne Creek fault (HCF) where the HCF is intersected by the ENE-trending DonaldaandCentralfaults.NorthoftheHCF,theNo1Veinishosted by the Quemont Rhyolite, whereas south of the HCF the vein is hosted by magnetic basalts and diorites of the Wilco Andesite Formation. The No 1 Vein extends across the HCF with only minor displacement, whereas the No 2 Vein has not yet been traced south of the HCF.A preliminary structural analysis of the mine shows that the HCF, which strikes 275° and dips 70° north in the mine area, has a reverse movement a lid that the flat dipping No 1 Vein is a tension vein. Both probably developed in response to the same stress conditions. Although the absolute age of the Donalda veins is not known, structural relationships indicate that they formed during the latest movements of the HCF, but prior to the intrusion of the Proterozoic D' Eldona Diabase. The occurrence along the HCF of gold-rich synvolcanic massive sulphides and much younger vein-type gold deposits (such as Donalda) indicates that the HCF was a very long-lived, deep-seated (?)structure which has controlled the circulation of gold-rich fluids over a long period of time."

Jan 1, 1990

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

By B. Hewitt

Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedw ell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1% (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2% improvement in the circuit underflow density. The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil® dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary to solution neutralisation improvements.

Jan 1, 2004

By K. L. Ford, D. R. Lentz, J. H. Rickard, R. P. Taylor

Abstract - Coupled gamma-ray spectrometric and lithogeochemical studies throughout the Heath Steele Mines area, Bathurst Camp, New Brunswick, indicate that primary and secondary geochemical differences exist between the stratigraphic footwall and hangingwall crystal tuff units which host the massive sulfide deposits. Of particular interest is Th, and to a lesser extent, Zr and Y, which are more concentrated in the hangingwall than the footwall crystal tuffs, whereas the opposite is true for TiO2. This expands on earlier lithogeochemical-chemostratigraphic results concentrated in the eastern part of the Heath Steele belt that led to revision of the local stratigraphy, and necessitated a structural re-interpretation of the area with implications for exploration. Although K depletion (decreased K and K/Th) is typical of chloritized footwall zones of chloritization, these features were not fully apparent here due to the recessive nature of these altered zones. In situ radiometric analysis using a portable gamma-ray spectrometer is a rapid, inexpensive analytical technique for chemostratigraphic characterization of rock units within volcanogenic massive sulfide deposit settings, provided there is a contrast in the distribution of natural radioelements, particularly Th and K.

Jan 1, 1998

Induced microseismicity monitoring is: ?Essential tool in improving the geotechnical understanding about a mine and its inaccessible surrounding rock masses. It helps to determine: -Event timing, location, and magnitude - identification of highly stressed areas -Event source mechanism - the physics of fracturing in its seismic source region -Seismic strain-rate distribution in 5D - identification of stress concentration or migration patterns -Geomechanical interpretation - identification of hidden geological structures or weaknesses in the ground -Strategy for mining e.g. by a block caving method - maximization of mine production and to optimize ground support design -Potential of future seismic hazards -Large event re-entry protocol, to improve mine safety ?The norm as part of mine safety maintenance and long-term mine design practices

Aug 1, 2013

By J. H. Ambrose

Introduction The copper smelter of the Hudson Bay Mining and Smelting Company, Limited was constructed to handle the concentrates produced by the concentrator, the residues from the zinc plant, concentrates from Sherritt-Gordon Mines, Limited, and other custom material that might be available. Construction work was started in 1929 and the first concentrates were smelted in November, 1930. From that time until June, 1931, the operations were more or less of an experimental or tuning-up nature. In designing the smelter, it was believed the following tonnages would be available for smelting per day: Copper Tons Content H. B. M. & S. Co. concentrates 331 14.0 per cent H. B. M. & S. Co. zinc plant residues 77 2.5 per cent Sherritt-Gordon concentrates 200 20.0+ per cent Consideration was given to wet-smelting the charge, but, in order to give greater flexibility to the operation, it was finally decided to roast the concentrates before smelting. Briefly, the smelter equipment consists of three Nichols-Herreshoff roasters, one reverberatory furnace, two Peirce-Smith converters, a Walker casting wheel, and a four-unit Cottrell plant, two units' for the roaster gases and two for the converter gases. A general plan of the smelter is shown in Figure 1. Prior to the commencement of smelter operations, a stockpile of about 9,000 tons of concentrates had been built up by the concentrator and the old pilot-mill. The zinc plant was in operation, but the equipment for drying the residues at the smelter had not been completed. Sherritt-Gordon did not commence their shipments of concentrates until April, 1931. The only flux available was barren sand from a pit ten miles south of Flin Flon, adjacent to the railway. Several small deposits of metal-bearing siliceous ore had been discovered in the district, but none of these were sufficiently large to be considered as a source of smelter flux. At the beginning of March, 1931, the entire stockpile of concentrates had been consumed, and available tonnage for smelting was limited to the daily production of the concentrator.

Jan 1, 1935

By R. Druffel, P. Wittke-Gattermann, M. Wittke

"The two tubes of tunnel Hirschhagen along the highway A44 in Germany, underpass the federal road B7, a railway line and the valley of the river Losse close to the city of Hessisch Lichtenau. The ground in the area consists of Triassic sand- and siltstones (""Buntsandstein"") as well as tertiary clays. Prior to tunneling, the groundwater in the area is planned to be lowered by means of a gallery of deep wells. As a basis for the design of this dewatering gallery, two large pumping tests have been carried out. The results of these tests have been evaluated by means of 3D-Finite Element analyses. By means of the large-scale model, the influence of the anisotropy resulting from jointing and bedding and the influence of fault zones in the area have been taken into account, which lead to a thorough basis for the design of the dewatering gallery.INTRODUCTIONThe 4.2 km long Tunnel Hirschhagen of the highway A 44 crosses below the federal road B7, a railway line and the river Losse close to the city of Hessisch-Lichtenau in central Germany. Both tunnel tubes are located in a subrosion depression in which Triassic sandstone and tertiary clay prevail. It is planned to lower the groundwater table in the area of the meadow of the Losse prior to tunnel heading [1]. Groundwater lowering is planned to be achieved by means of a series of large pumping wells. The bottom of the river Losse will be sealed in order to avoid direct inflow of water from the river into the ground (Fig. 1 and 2)."

Jan 1, 2015

By Torsten Zeller

Due to the increasing worldwide demand for raw materials and the resulting rise in commodity prices more expensive processing that is able to utilize complex ores becomes economically viable. This and increasing ecological awareness is why the interest in recycling and urban mining is steadily growing in Germany. In addition to that; landfills do also contain elements, which were not targeted over the period, when they were being accumulated. Examples are rare earths, indium, gallium, cadmium, arsenic, selenium and tellurium. Also copper, zinc and lead, the target components of ancient mining, can be obtained due to more effective processing and smelting technologies. Funding by the German Federal Ministry for Education and Research, entitled "r³ ? Strategic Metals and Minerals ? Innovative Technologies for Resource Efficiency" also indicates the high level of strategic interest. It is against this background that the research project "Exploitation of the Raw Material Potential of Mining and Metallurgical Tips in Respect of Sustainability as Exemplified in the West Harz Mountains (ROBEHA)" has been implemented. A major concern of this project is the possible transfer of results to landfills in other areas. Therefore the development of an expert system based on the innovative processing methods and a method manual for urban mining are the central components of the investigation. This will provide an important contribution to the cost optimization of ensuing urban mining projects. To ensure the success of landfill mining projects it is necessary to record the composition and quality of the deposits accurately. Also the environmental impact caused by landfill mining and changes in the natural and cultural landscape will be considered in a multicriteria evaluation method. Depending on their origin the tips are divided into the categories mining, processing, and smelting. The content of a landfill and thus the economic potential in terms of urban mining is dependent on the type and composition of the deposits (host rock, gangue, and ore mineral), the available processing and smelting technology, and the target components at the time of mining. Zinc, for example, was not been processed until the 19th century, when it gained attention as being material of economic importance. After such knowledge about a landfill is obtained the decision for further investigations can be made. For a total of 158 landfills in the Harz Mountains, both the volume and the approximate contents of copper, zinc, and lead has been estimated for the different types of tips within past research projects. Based on the prices of the London Metal Exchange (LME) and a euro/dollar exchange rate of 0.76 (as of 03/05/2012) and assuming a minimum density of ? ? 1.5 t/m³ a average value of 1.6 billion ? in copper, zinc, and lead can be obtained. Although only these three metals are considered in this first estimate, it demonstrates the potential of landfill mining and the need for further research. KEYWORDS Urban Mining,

Aug 1, 2013

By E. Haccuria

Due to the growing share of electrical cars, the use of lithium ion batteries significantly increased. Recycling of these batteries is essential to safely dispose hazardous materials as well as to recover valuables (Cu, Ni, Co, etc.). In order to optimise the recycling process, accurate information is required on the slag phase equilibria for battery smelting. The slag is a multi-component system containing alumina from the battery cases, silica and lime from fluxes, and manganese and lithium from the electrode materials. The present study accurately determined the phase equilibria in the "MnO"-Al2O3-SiO2 sub-ternary system at metal alloy saturation. Particular attention was given to the accuracy and reliability of the final results by highlighting the different reaction pathways, mass transfer- and reaction mechanisms taking place in the system during experiments. This attention enabled improved experimental methodology and measurements. Based on the present study, further measurements will be undertaken in the quaternary "MnO"-Al2O3-CaO-SiO2 system at low "MnO" concentrations, which closely represents the future recycling industrial slags.

Jan 1, 2014

By E. G. Gaylord

THE material improvements which have been made in the practice of exploiting oil and gas reservoirs in the United States during recent years may be attributed largely to: (1) The necessity for drilling deeper wells at costs not much greater than was formerly expended on shallower wells. (2) The necessity for producing oil at a lower cost per barrel. (3) A growing recognition of the importance of the nature of production practice upon ultimate yield of oil and gas. The first two of these factors result, to a large extent, from the fact that a greater proportion of new development has been deeper development, and these wells have been drilled in the face of progressively lower per well allowables. In California, for instance, maximum allowables have declined from 400 barrels per day in March, 1938, to 156 barrels per day in September, 1940, and during this same period some 125 wells were drilled to the deeper 10,000-foot producing horizons discovered during this time. The third item listed above results from our increasing knowledge of the basic factors which influence the amount of recovery we may expect from reservoirs. In addition to the longer-range planning now being undertaken by the more prudent operators, State proration and conservation laws have focused attention upon the importance of methods conducive to obtaining progressively greater quantities of the hydrocarbons in place. In a paper of this length it will be possible to discuss only a few of the recent advances. An effort has been made to select the more important of these and to indicate, where possible, the factors which have made these advances possible.

Jan 1, 1941

By T. Narita

The diffusion barrier coating system (DBC system) was designed to suppress interdiffusion between alloy substrate and coatings in addition to ensuring slow oxide growth at high temperatures. In this report the concept of the DBC system will be introduced, and the results obtained for various heat-resistant alloys are presented. In this DBC system the s-phase of the Re-Cr-Ni system was selected as the barrier and is formed by electroplating Re-Ni and Ni films from aqueous solutions, followed by Cr and/or Al pack cementations. A typical DBC system consists of Ni-base superalloy / triple s-Re based alloy layer / ?’-Ni3Al and/or ß-NiAl (with or without Pt addition) / a-Al2O3. It was found that the DBC system maintained its structure for long time exposures because the s phase has tie-lines with the ? and ?’ alloy substrate and the ?’ and/or ß coating. The s-Re based alloy can suppress both the inward Al diffusion and the outward diffusion of alloying elements. The DBC system was successfully applied to various heat-resistant alloys such as Ni-Mo and Fe-Cr-Al based alloys, and these alloys with the DBC system were creep-deformed slowly under external applied stresses. A simultaneous diffusion coating process for Al and Hf was developed using Hf+NH4Cl+Al2O3 pack cementation. To obtain reliable and long-life coatings the combination of alloy substrate, coating, and external scale should be considered as a total system, to optimize oxidation resistance, structural stability, and mechanical properties.

Jan 1, 2010

By Y. L. Mehta

The working experience of the Zinc Smelter, Debari, Udaipur with process modifications and iron control practices is described in detail in this paper. Most of the modifications were made at different times as part of capacity enhancement campaigns that led to distinct advantages, thereby increasing both zinc production and recoveries. This smelter came into existence in 1968 with a humble beginning of producing 18,000 metric tonnes (MT) of zinc per annum, using the conventional batch hydrometallurgical roast-leach-electrowinning technology. Zinc production capacity was increased stepwise to 45,000 MT, 49,000 MT and 59,000 MT, by making suitable process modifications and adopting new technologies, particularly in the leaching section. During these modifications, the process of iron separation as Moore cake was also changed to jarosite cake production. At present, jarosite is being disposed in a secured landfill at the Zinc Smelter, Debari (ZSD) and as Jarofix at the Chanderiya Lead Zinc Smelter (CLZS). As a result of subsequent in-house performance improvement and debottlenecking campaigns, this smelter could achieve further increases in production. Zinc production for the financial year 2005-06 was 81,000 MT.

Jan 1, 2006

By Keith Donovan

Why are we here? Improve equipment performance & health ? Eliminate undesirable downtime and expensive secondary damage ? Maximize equipment life, optimize running costs (reduce costs) ? Improve safety and environmental performance ? Capture and consistently apply equipment knowledge ? Improve Proactive Maintenance processes & practices

May 1, 2009

By C. M. Campbell

In his report on the Coal Resources of Southern Vancouver Island, Mr. J. D. MacKenzie stated that: "For various reasons it has been imagined that the coal deposits of Vancouver Island are extremely large and readily available." "Unfortunately," he added, "neither of these assumptions is correct." The chief disability under which the Island mines now labor does not concern the extent of the deposits. There is ample coal for the present demand. It does, however, concern the availability of the coal. If it were readily available the fuel-oil competition would not be serious and there would be no competition with Alberta, American, Welsh, or Australian coal along the Pacific Coast, for Vancouver Island coal could be produced at a price that would cut out all competition. The outstanding operating difficulty common to all Island mines is the extreme irregularity of the coal seams. To most people a coal seam is synonymous with uniformity, and in most coal seams a condition found at one point will be repeated at other points in the same seam throughout the basin. The accompanying drawings show how very far this is from being true in the Cassidy mine, which, in many respects, is typical of Vancouver Island mines. Figure I is a plan covering about 160 acres of the Douglas seam, the only workable seam in this part of the district. The area shown represents what has been the best producing part of the mine and indicates the very large percentage of the seam where the coal is either entirely lacking or so small in amount that it cannot be profitably recovered.

Jan 1, 1924

By Alexander Smith

"The three principal known mineral deposits of the Taku River area lie in the Tulsequah synclinorium. The axis of this north-south trending structure is along Tulsequah River valley; about 6 miles east of the eastern contact of the Coast Range batholith.The one proven mine of the area, the Polaris-Taku, is on the west side of the valley. It is a gold property, the gold occurring in fine needles of arsenopyrite disseminated in carbonatized volcanics. The mine was originally called the Whitewater, and the adjacent area the Whitewater gold belt. During the years 1937 to 1942 gold having a value of $3,284,000 was produced from 313,500 tons of ore milled."

Jan 1, 1954

By L. Shasko, M. Hurlbert

As climate change is increasingly perceived as a problem, and fossil fuel based power production options are increasingly limited through regulatory restrictions and public distaste, future options become constricted. Reflexivity and social learning elicited through qualitative and mixed research methods offer important insight into what future power production pathways might be. Given factors of cost, baseload requirements, and energy density, options such as nuclear may be increasingly accepted. This paper explores this literature and possible methods of pursuing the reluctant acceptance of nuclear energy.

Jan 1, 2020

By Harvey McLeod

M3 -Technology HOWEVER:In practice we have limitations ?Clients: aggressive or cost based; inexperienced ?Consultants: ?expanding market w/training limitations ?Prescriptive designs ?Lack of senior oversight ?Regulators: difficult to retain technical capacity ?Stakeholders: perceptions and expectations ?Physical settings: challenging terrain, climate, soils/rock Do M3?s Perform? YES?Generally M3?s since mid-1960 do perform ?BC Closed Mines: Afton, Highmont, Trojan, Bethlehem, Cheni, SNIP, NO?ARD/ML issues?e.g. Equity Silver, Samatosum; selenium, cadmium, sulphate

May 1, 2010