Search Documents

By T. Bhambhani, O. Yavuzkan, D. R. Nagaraj

"Cu ore bodies commonly contain oxide Cu at the surface, with sulfide Cu content increasing with depth. The recovery of oxide Cu minerals by flotation is a longstanding challenge in the minerals industry, especially for high acid-consuming ores which would not be economical for direct acid leaching. Current practice of oxide Cu recovery involves sulfidization (often using controlled potential sulfidization or CPS) using NaSH (or Na2S) followed by flotation using traditional sulfide collectors. CPS has shown to improve recovery of oxide Cu but has the following limitations: a) HSE issues with NaSH, b) high consumption of NaSH, and c) inability to recover certain oxide Cu minerals because they are refractory to sulfidization. The oxide Cu flotation is further complicated by the presence of certain non-sulfide gangue minerals which adversely impact both recovery and selectivity.Over the past eight decades, numerous collectors have been proposed and evaluated for the direct flotation (i.e. without sulfidization) of oxide Cu minerals, the most researched of which is alkyl hydroxamate. While there are numerous publications dealing with the fundamentals of interaction of alkyl hydroxamates with single minerals, there are few publications which discuss the practical aspects of alkyl hydroxamate use in ore flotation, particularly their use with sulfidizing agents. Case studies in this paper include methods to identify optimum combinations of sulfidizing agents and oxide collectors to maximize recovery for various types of ores. It was observed that some ores do not require any sulfidization, while others require at least partial sulfidization to improve efficacy of AHX. Depending upon the ore type and mineralogy, recovery improvement in the range of 5 to 15% units, over and above that achieved with CPS, has been observed with the use of AHX. For ores requiring high dosages of NaSH, it was shown that AHX can be used to reduce the NaSH consumption significantly. The challenges associated with the presence of non-sulfide gangue minerals in oxide copper ores are included, and the use of modifiers to alleviate the associated problems and enhance the performance of AHX is discussed."

Jan 1, 2016

By P. R. Goad

"Kidd Creek is a large volcanogenic base metal sulphide deposit, located near the west end of the Abitibi greenstone belt, 27 km north of Timmins, Ontario. The rhyolite geology is characterized by a NNE-striking and steeply east-dipping package of rhyolite volcaniclastics upon which has been imposed a strong ESE-striking and north-dipping structural fabric . Massive rhyolite units with grey-black. chloritic cores and yellow, sericitic margins intrude as dykes into the stratigraphic footwall and as sills higher in the stratigraphy. Massive rhyolite units positioned near the top of the felsic pile exhibit an extensive marginal development of hydraulic fracturing and are termed crackle-brecciated rhyolite.The stringer sulphide zone is positioned in a lobate blanket of crackle-brecciated rhyolite at the top of the felsic pile. The stringer sulphide zone is characterized by a mature chemical alteration, being specifically depleted in alkalis and enriched in iron-rich chlorite. with accompanying silica, sericite and carbonate alteration. A suite of trace elements characterizes this mature alteration. The massive rhyolite units, which intrude lower in the rhyolite volcaniclastics, exhibit a core of weak chlorite alteration and strong marginal sericite alteration. Tight or unfractured massive rhyolite units are essentially devoid of sulphide mineralization and exhibit a suite of trace elements characteristic of this immature alteration. It is interpreted that the massive rhyolite units intruded into an already evolving system and ""choked-off"" active conduits carrying hydrothermal fluids and subsequently acquired an immature alteration signature. Rhyolite units positioned higher in the pile developed intense hydraulic fracturing and a mature alteration coincident with the formation of the stringer sulphide zone. In summary, a model, based strictly upon the rhyolite geology, is reviewed to assist in the exploration for volcanogenic base metal sulphide deposits."

Jan 1, 1985

By B. Panton, J. Carvalho, E. T. Brown

High-capacity, post-tensioned anchors have found wide-spread use in initial dam design and construction, and in the strengthening and rehabilitation of concrete dams to meet modern design and safety standards. Despite the advances that have been made in rock mechanics and rock engineering during the almost 80 years in which post-tensioned anchors have been used in dam engineering, some aspects of the rock engineering design of high-capacity rock anchors for dams have changed relatively little over the last 30 or 40 years. This applies, in particular, to the calculations usually carried out to establish the grouted embedment lengths required for deep, post-tensioned anchors. These calculations which involve a number of aleatory and epistemic uncertainties, usually make simplified assumptions about the distribution and values of rock-grout interface shear strengths, the shape of the volume of rock likely to be involved in uplift failure under the influence of a system of post-tensioned anchors, and the mechanism of that failure. The resulting designs are generally conservative. These aspects of the rock engineering design of large, post-tensioned rock anchors for dams could be improved by making greater use of modern, comprehensive, numerical analyses in conjunction with 3D models of the rock mass structure, realistic rock and rock mass properties, and the results of prototype anchor tests in the rock mass concerned.

Jan 1, 2015

By Omkar N. S. Beruar

Extraction of sill pillars has always been problematic because of high risk of seismicity and rockburst. Depending on a number of factors, a sill pillar can undergo different failure modes and cause problems in the mine. Of these, sudden and uncontrolled failure of part(s) of the pillar leading to highenergy seismic events and rockbursts is a main concern because it is not possible to predict the location and time of a rockburst apart from its potential to cause extensive damage to the mine structures. To date, a comprehensive technique for sill pillar design and recovery does not exist. Conventional methods of pillar design, such as the pillar stability graph method, are utilized to design stiff sill pillars. In these design approaches, the post-peak response of the pillar-rock system is not considered. This is in part due to a lack of clear and comprehensive understanding of the post-peak behaviour and failure mechanism of sill pillars. In general, the strength of a rockmass is described using a failure criterion. When stresses reach the strength of the rockmass, the rockmass does not necessarily become unstable and knowledge of the loads alone is not enough to assess the instability conditions accurately. In fact, it is not possible to predict instability of rockmass based on the strength/stress ratio alone because instability depends not only on this ratio but also on the loading condition and loading system characteristics. The loading system can dictate whether the sill pillar will go through a stable or unstable failure process. This paper examines the influence of various parameters such as the pillar width to height ratio, the extraction rate, and placement of backfill on the Loading System Stiffness (LSS) and the Pillar Stiffness (PSS). The ultimate goal is to design yielding sill pillars that would yield in a stable manner and will reduce the risk of pillar rockburst. Plane strain finite element analysis is conducted using the generalized Hoek-Brown failure criterion with elastic-brittle-plastic parameters. Examples are given to demonstrate how to calculate these stiffness values and assess the stability condition of sill pillars. It is found that increasing the rate of extraction increases the likelihood of unstable yielding of the pillar as has been found in other studies. Placement of backfill in a timely fashion in the stopes above and below the sill pillars increases the stiffness of the loading system. This indicates that backfilling of stopes while creating the sill pillar increases the likelihood of stable yielding of the sill pillar.

Aug 1, 2013

By David A. Orava, Richard C. Swider

"The technical knowledge and practical experience accumulated by industry and others in abating acid mine drainage (AMD) is being proactively applied at every phase of the mine life cycle. This paper traces the mine life cycle from exploration to post closure monitoring and maintenance, and reviews AMD abatement measures that have become an integral component of exploration and mining activities.Attention is increasingly being given to evaluating AMD potential as part of exploration work, and studies related to project feasibility and design. Mining, mineral processing, and waste management options are selected taking into consideration their suitability to inhibit AMD. These inhibition measures are typically committed to in closure plans submit-ted at the permitting stage. Mines are operated and decommissioned, often progressively, as planned and in accordance with environ-mental protection policies."

Jan 1, 1996

By Michel Ruel

Most plants do not track how their systems perform. Optimization is the easiest way to benefit from your control systems. We suggest an approach in four phases. The first phase is to assess all equipment to determine the performances for instruments, valves, variable speed drives, and other equipment. The second phase is to remediate instrumentation problems, including the ones pertaining to valves, variable speed drives, analyzers, transmitters. When equipment is in order, loops are put back in automatic mode. If a loop oscillates, use standard default values for this type of loop. The third phase consists in validating the control strategies, properly configuring the systems (control system, programs and parameters, HMI, alarms), and then tuning the loops and control strategies. The fourth phase consists in analyzing the process and expected performances in order to optimize the control loops and control strategies. If performance is not sufficient, a decision tree will be presented to determine the right approach: advanced regulatory control, model predictive control, or fuzzy logic control. Once all steps have been completed, control performance monitoring software is used to sustain the results and pinpoint equipment or loops not performing as stated. Alarm management and rationalization could also be performed after auditing the alarm system, if needed. Examples from plants will be used to demonstrate how this step-by-step method is applied and produces results. INTRODUCTION Maximizing what you already have is the best investment to remain competitive. This article aims to show the benefits of a systematic approach using modern tools to improve plant performance. We at BBA suggest dividing the work in four phases, and a subsequent phase can begin when the previous one has progressed: Assess, Remediate, Stabilize, Optimize, or add advanced control. This approach has been successfully applied to several sites. Examples and illustrations from these plants demonstrate how this step-by-step method is applied and produces results. Under the BBA method, there are four questions to answer before proceeding to the next step. For each control strategy, you should ask the following questions: Assessment: Does it work? Remediation: Do you use it? Stabilization: Is it stable? Optimization: Does it perform? Do you need advanced control?

Jan 1, 2019

By D. Campbell

Mining activity is increasing in northern boreal and subarctic regions of Canada. This is the case in the far north of Ontario, especially in and near the Hudson Bay Lowland (HBL). De Beers Canada opened the Victor diamond mine in the centre of the HBL in 2008, and advanced exploration and impact assessments are occurring to the west in the ?Ring of Fire? for ferrochrome, nickel/copper, iron/ vanadium and platinum-group elements, making it one of the richest mineral finds in Canada in recent years. However, the HBL is also a near-pristine, sensitive environment. Its peatlands forms the third largest wetland in the world and are globally important stores of terrestrial carbon. Human populations in the region are sparse, consisting almost entirely of First Nations communities. Local First Nations also have a strong land ethic and greatly influence mining developments. Through formal agreements, they have insisted on a gold standard for environmental management, including a small mine footprint and the return to representative native ecosystems after mine closure. However, knowledge on the revegetation of subarctic and northern boreal ecosystems is limited. Here, we are conducting research at the Victor mine to develop gold standard protocols for the revegetation of disturbed peatlands and mine waste uplands and present a summary of results. We first tested existing protocols for peatland restoration from southeastern Canada. We collected peat-forming plants from nearby muskeg, spread them sparsely over disturbed peatlands and applied a light phosphate fertilizer, but unlike southern protocols, no mulch appeared to be required to produce a representative cover of peat-forming plants within three years. A bigger challenge is the reclamation of uplands made of mine waste back to representative ecosystems. We first characterized reference conditions for uplands in the HBL, which are scarce in the region. Nearby natural uplands were divided into two classes, interior uplands and uplands along river valleys. Multiple parameters were examined at these sites including soil development, bulk density, soil chemistry in the rooting horizons, plant cover by stratum, plant species composition and dead wood. The mean condition and, more importantly, the range of these parameters allow us to set broad targets for progressive reclamation, which will facilitate success. Finally, we characterized local upland plant species through their functional traits to determine their likely abilities to colonize, grow and contribute to ecosystem processes. A classification of species by these simple functional attributes will help restoration managers to select candidate species to meet different goals at different successional stages (i.e. good versus poor dispersers or establishers). Research into these protocols remain in the early stages, but show promise that gold standards can be achieved to ensure that mining wastes can be reclaimed to productive ecosystems.

Aug 1, 2013

By W. B. Burchall

Introduction In presenting this paper the author wishes to state that the opinions here given represent only his personal views. A general survey of the subject has been attempted, but such deductions as may have been drawn are not necessarily endorsed by the Company with which he is associated. The aeroplane as an instrument of transport is yet a novelty, for it is only twenty-five years since man first flew. This statement, by itself, may be very deceptive, for compared with the steam locomotive or even the auto-mobile, this infant in industry has made some remarkable showings. The 'actual performance' speed-curve of aircraft plotted over a ten-year period is rising faster than the 'expectancy' speed-curve of 1924 indicated, and it should be noted that, today, the possibilities of 600 miles per hour provoke less scepticism than did the prophecies of 400 miles per hour only a decade ago. Commencing with the remarkable achievement of raising one man into the air, aircraft with an all-up weight of 14 tons are now in daily use on the British airways, and recently a non-stop flight of 5,340 miles was accomplished in an aeroplane, without refuelling. More true than ever is the statement that the records of yesterday are commonplace tomorrow, for new ideas are today seized on and exploited to the utmost once the period of scepticism and doubt has been overcome. In fact, so many new ideas have been brought forward, during the past few years, and applied successfully in our economic life, that one may well ask if today we are not a little too impatient, too exacting in demands, forgetting that real worth-while progress -is attained by no short-cuts.

Jan 1, 1933

By W. G. Worcester

IN the presentation of this paper to the Institute, three objects are in the mind of the writer: first, to set forth the close relation which, of necessity, exists between ceramics and the industrial minerals; second, to clarify the apparently hazy understanding which many have of ceramics in general; and lastly, of equal or even more importance, to stimulate a greater interest in the industrial minerals, especially in those used and required by the ceramic industries. While Canada is now producing in large quantities a fairly wide variety of the ceramic industrial minerals, there are some which are not known to occur in the Dominion. Hence it is to be desired that our geologists, prospectors, and others, while on field work, should be on the look out for commercial deposits of such minerals as diaspore, bauxite, ucts of a value in excess of $600,000,000, a figure which places ceramics as kyanite, massive topaz, and sillimanite. A find of any of these in quantity would prove of very great importance and value to the country as a whole. At this point it seems desirable to introduce formally the word ceramic or the plural of it, ceramics. In doing so it may be stated that the origin of the word dates far back in history in that it was derived in part from the Greek word Keramos, 'a potter' or 'pottery', which in turn has been traced back to an older Sanskrit root meaning 'to burn' or 'burned stuff', having reference, no doubt, to burned pottery or other clay wares; and the word was so used until near the close of the last century, when the world's first schools of ceramic engineering were established in the United States. The use of the term ceramics was then expanded to cover a much larger field the entire field of the silicate industries and products. At one time it was suggested by a limited number of ceramists that the term 'ceramic engineering' be changed to 'silicate engineering'. This proposal, however, gained little support and was soon abandoned.

Jan 1, 1945

By E. Benguerel, G. Monteith, L. Centomo, S. Pelletier

In early 2007, it became apparent that with changing concentrate feeds, the magnesium (Mg) load projected for CEZinc starting in 2009 and beyond would quadruple and overwhelm the current Mg process bleed capacity. A project was started, following design for six sigma (DFSS) standards, to select both the optimal process and to evaluate its target capacity for the Mg bleed circuit. The economic and process risks of under or over-designing while Mg reduction efforts were underway at the mines also needed to be evaluated. This paper describes the project methodology, the impact on the plant, and some potential optimizations for CEZinc's basic zinc sulphate (BZS) Mg bleed process.

Jan 1, 2008

By J. S. Redpath, W. R. Dengler

"A description of the equipment used and the electrical-mechanical problems encountered in sinking a deep shaft is given. This shaft is currently being sunk to a depth of 7,115 feet. Some of the features of the sinking plant are a 6,500-hp double-drum hoist, a Blair stage hoist, special high-capacity mucking gear, a Galloway stage, high-tensile stage suspension ropes and 12-ton sinking buckets.INTRODUCTIONIN THE EARLY FALL OF 1965, a contract was let, by The International Nickel Company of Canada, Limited, to Shaft Sinkers (Canada) Limited -J. S. Redpath Limited -Joint Venture, • to sink and equip the Creighton No. 9 shaft at their Creighton Mine proper-ty in Ontario. This paper describes the electrical and mechanical equipment used by the contractor on this project, and details various problems that were en-countered.The shaft itself is circular in section and is lined with monolithic concrete. Upon completion, it will feature twin skip compartments, a cage compartment, counterweight compartment, manway and pipe compartment. The finished diameter of this opening will be 21 feet and the shaft will bottom 7,115 feet below the collar. The present depth of the shaft (April, 1968) is 5,400 feet. The opening is concrete lined as excavation takes place and the steel will be placed in the shaft upon completion of sinking. Hoisting is done on rope guides which are part of the stage suspension system."

Jan 1, 1968

By K. S. Raja, F. Battick, B. Pesic

"CeO2 doped with lower valence cations, such as Y3+, Sm3+, Gd3+ etc. is considered as electrolyte material for low temperature SOFC. Doping introduces additional oxygen vacancies and improves ionic conductivity. This work describes the preparation of yttria-calcia doped-ceria precursor material, its sintering in DC and AC field methods, and characterization of sintered electrolytes with respect to the ionic conductivity. Doped precursor materials were prepared by a controlled co-precipitation process. Sintering of prepared, pelletized particulates was carried out using three different methods such as: 1) conventional; 2) spark plasma sintering; and 3) an alternating current field at 1125°C (AC assisted sintering). The mechanism involved in the conductivity improvement as a function of defect density, grain boundary area and phase stability will be discussed. INTRODUCTIONThe performance of SOFCs depends highly on the properties of materials. Subtle variations in the composition, microstructure, or density of SOFC components can considerably alter the power output capabilities of fuel cells. Early SOFCs utilized zirconia based electrolytes but efforts in lowering the operating temperatures of SOFCs have prompted investigations into several other oxygen ion conductors – often modified with dopants to either promote the formation of oxygen vacancies or to stabilize a vacancy rich high temperature phase – such as bismuth oxide, lanthanum gallate, and ceria.The transport of oxygen ions through the electrolyte first begins with diffusion into the material. While this is generally a surface kinetics phenomenon, it is safe to say that it is highly dependent on oxygen pressure and vacancy gradients. The role of the cathode in SOFCs is to reduce oxygen at the electrolyte surface creating an O2– ion gradient which induces permeation into the material. Once inside and under the influence of a potential field, O2– ions migrate by a vacancy hopping mechanism, Catlow, C.R.A. (1990), effectively exchanging positions throughout the matrix until they reach the anode and react, thus leaving the matrix."

Jan 1, 2012

By O. Babak, J. G. Manchuk

ABSTRACT A significant factor in evaluating bitumen recovery from an oil sands mine is the particle size distribution (PSD). Increased understanding of mined ore quality and improvement in predictions of recovery can be achieved through PSD modeling. This paper addresses PSD modeling using geostatistics. PSDs may be described using many discrete particle sizes, making this a challenge. The approach parameterizes PSDs with a few statistics. A lookup table is used to reconstruct the PSDs based on models of the statistics. The workflow is applied to Total E&P Canada’s Joslyn Lease and yields good results that reproduce input statistics without introducing artifacts.

Jan 1, 2013

By David A. Edgecombre

This paper discusses modern practices in the extrusion of steel. Particular emphasis is given to a description of the Ugine Sejournet method of extrusion, involving the use of glass as a hot work lubricant. Other methods are also mentioned. A brief history of extrusion is presented; present practices in the quality extrusion of tubing and solids are described; and the future potentials of the) process as a tonnage producer are briefly discussed. The advantages of extrusion and the reasons for the use of a glass lubricant, as well as the various methods of using glass, are given. The process, as described, is being used in the manufacture of large commercial quantities of stainless steel tubing and sections. This extrusion process is an essential and unique means of forming such atomic-age materials as titanium, zirconium, molybdenum and other super alloys all of which are materials required in the creation of nuclear installations.

Jan 1, 1963

By J. Grant Spratt

THE Turner Valley gas-field, situated some thirty miles southwest of Calgary, Alberta, has been the topic of much discussion, particularly from a geological viewpoint. Several papers (1, 2, 3, 4, and 7) dealing with the structural and stratigraphical geology have already been published and are available for reference(l). In this article, the geological conditions will be treated only as they directly refer to the crude-oil prospects along the west flank of the anticline. HISTORY During the past twelve years, Turner Valley has been known mainly as a field which has produced a high-gravity naphtha from relatively large quantities of gas. For about ten years prior to the discovery of this naphtha-bearing gas, which is produced within the upper 450 feet of a dolomitic limestone of Carboniferous age, a minor production of light crude-oil was obtained from overlying sands of Cretaceous age. Up to June 1st of the present year, the field had produced 9,473,582 barrels of naphtha from approximately 829,000,000 M.c.f. of gas. For the past four years, the total daily production of 80 to 90 wells has averaged about 3,200 barrels of naphtha from 250,000 M.c.f. of gas. This is an average of 13 barrels per million cubic feet. The naphtha is extracted from the gas by ordinary gas-oil separators and absorption plants. After the naphtha has been recovered, about ten per cent of the gas is marketed for fuel to supply the cities of Calgary and lethbridge and intermediate cowns. The remaining ninety per cent is burned to the atmosphere, with the exception of some four to five million cubic feet per day which the Calgary Gas Company score in the depleted Bow Island gas-field.

Jan 1, 1936

By M. Leroux, J. A. Finch

"Sizing below 38 µm (400 mesh) is an increasing requirement in mill testing laboratories. The Cyclosizer is gaining wide acceptance in this role. A recent alternative is to use electro-formed sieves (micro-sieves), which are available with openings down to 5 µm. The advantage of micro-sieving is a cut size which is independent of mineral density, easier retention of the fi nest fraction and reduced purchase cost. A simple method of microsieving using an ultrasonic bath, which performs readily to 10 µm, is described.A systematic study of Cyclosizing and micro-sieving is reported for three samples; silica, copper oxide and a lead concentrate. Micro-sieving gave comparable results. Comparison with a standard sizing method, the Sedigraph 5000D, revealed misplaced material in each fraction by both methods. The range for micro-sieving was from 20% to 60% depending on the sieve and material; for the Cyclosizer it was a consistent 40-50% for all cones and all materials. The Cyclosizer can be sensitive to feed mass and particle size for dense materials. It is recommended that for minerals of specific gravity greater than 5, no more than 35 g of -38 µm be used.The disadvantage of micro-sieving is that it requires continuous operator attention and sieving time depends on sample mass. To fractionate 35 g-as used on the Cyclosizer and considered at reasonable mass for mill testing purposes-through 25-, 15- and 10-µm sieves requires about 80 minutes.IntroductionParticle size has a pronounced influence on mineral separation processes. Consequently, the measurement of particle size plays an important part in mill testing. By far the most common method is by screening. This, however, is usually limited to 38 µm (400 mesh) or occasionally 25 µm (500 mesh). Increasingly, mineral products are becoming finer than this limit and consequently finer sizing methods are required."

Jan 1, 1982

By J. -C. Sztuke, M. Cao

ABSTRACT Wash water and polyethylene oxide (PEO) were used in the flotation of quartz and coal. Wash water decreased entrainment of –15 µm quartz. The optimum superficial wash water rate was 0.05 cm/s. PEO also lowered entrainment. The combination of wash water and PEO led to a slight further reduction in entrainment. For 1:1 mixtures of –15 µm quartz and –300 µm oxidized coal, the combined use of wash water (0.05 cm/s) and PEO increased the separation efficiency from approximately 30% to > 70%, whereas wash water alone at 0.05 cm/s did not lead to a discernible increase.

Jan 1, 2014

By Thomas C. Poulter

Abstract The Poulter seismic method of geophysical exploration is an attempt to obtain an increased efficiency in the conversion of the energy of an m~pl06ion into useful energy which has directive properties and which contains a minimum of random frequency and random phase relations. Very little effort has been made in the past to simplify OT even control the uniformity of the seismic energy being introduced into the ground. The Poulter seismic method is also an attempt to improve the signal-to-noise ratio not merely by trying to complete the impartial filtering done by the earth on ,the continuous spectrum of primarily high-frequency energy radiated from a shot point but by applying a frequency control at the point of origin of the seismic wave. The energy from a shot-hole charge is peaked in a frequency which is much higher than will be transmitted through the ground, and its absorption introduces background interference. Only 10 to 20 per cent of the seismic energy of a shot-hole charge .is directed downward in a 90-degree vertical cone, whereas, from a pattern of charges detonated above the surface of the ground, 85 per cent of the seismic energy is included in a 90-degree cone and in some cases it is even confined to as small as a 30-degree cone. This greatly reduces the horizontally distributed energy, thereby producing a marked improvement in the signal-to-noise ratio. The frequency of the signal energy may be peaked in a rather narrow range by the proper application of two or more impulses upon the surface of the ground controlled as to direction, magnitude, and timing. These impulses may be controlled by the reflection shock wave technique, the pressure pulse technique, and the sequence firing technique, using the primary controls as outlined. The information obtained from the study of directivity of seismic energy in a high velocity, uniform material such as the ice on Taku glacier, in the Juneau ice field in Alaska, has been of great assistance in the application of the method to oilfield and mining problems.

Jan 1, 1950

By J. S. DeLury

Introduction The problems of metallogenesis are largely related to those concerning the origin of igneous rocks, which, in turn, are involved with the question of crustal mechanics. Many ore-bodies are genetically related to associated intrusive and there is an equally close association apparent between igneous intrusion and crustal deformation. The problem of ore-deposition is concerned, therefore, with the fundamental problems of geology. For a long time speculations regarding crustal movements rested largely on the contraction theory and its associated conceptions. Vertical movements were considered to be all important and horizontal movements secondary to them. Magmas were pictured as rising more or less vertically in the crust and were believed to form in vertically disposed magma-chambers or reservoirs. The principle of magmatic differentiation seemed to offer the best explanation of the origin and association of diverse rock types and it seemed also to require the existence of quiescent magma-chambers for the admittedly slow process of differentiation. Accumulating evidence of the importance of horizontal movement in the crust, has, along with other considerations, discredited the contraction hypothesis and many of the inferences that go with it. The same evidence may require some change in the prevailing conception of the origin of the various types of igneous rock and of the mechanics of intrusion. Geologists are now at sea concerning some of the vital and fundamental problems of the crust, and the field is open for speculation. The writer is developing a hypothesis which seems to permit an explanation and? a correlation of earth structures and phenomena. If it rests on a firm foundation, the hypothesis, because it is fundamental, is certain to have a profound bearing on the problems of economic geology. It is for this reason that an outline of the hypothesis is offered at this time. Only a few of its economic bearings are foreseen at this time and these will be indicated.

Jan 1, 1932

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011