Search Documents

By R. Loj

Katowice Coal Holding (KHW) is one of the largest coal companies in Europe. The company owns five coal mines with a daily output of around 60 000 tons of coal. In the Katowice city area, very good quality steam coal is extracted. The depth of mining varies between 400 and 1100 m and some of the mines rank amongst those most afflicted by methane in the Upper Silesian Coal Basin, with the methane hazard having a significant impact on production and safety. ?Myslowice-Wesola? mine, being a part of the Katowice Coal Holding is characterized by high methane and rockburst hazards. The mine is equipped with a modern surface drainage pumping station. At the mentioned mine, longwall 514 was selected for analysis of its methane emission. The longwall was extracting the thick seam 501 (over 4 m), at a depth of over 900 m, which was subject to high stress and high gas concentration conditions. At a distance of about 50 m above, seam 501 is covered by thin seam 416. The strata between these two seams are sandstone and mudstone layers. In the floor of seam 501, with a thin shale interlayer, is located seam 510, which is the thickest (over 10m) and richest coal seam in the Upper Silesian Coal Basin. In longwall 514 and it?s vicinity, methane was the dominant risk. For this longwall three methods of classical gas drainage were carried out. At first, drainage was undertaken using long boreholes from a cross-cut at level 665 m, located far from the production panel. Later, it was performed using typical boreholes drilled from the ventilation gallery (tail gate road). Finally, it was undertaken using a degassing drift executed in the upper coal seam 416. All of these headings, ie. cross-cut level 665 m, the ventilation road and conveyor road in seam 501 and the degassing drift in seam 416, were equipped with media for drilling and proper drainage pipelines. Due to the high rockburst hazard and some problems with caving, several kinds of de-stressing and torpedo blasts were carried out in both coal seams and roof rocks. The subsequent analysis and experiments allowed the establishment of some general rules for carrying out degassing operations effectively. The effectiveness of a degassing drift was demonstrated. In some instances, the system allowed more than 70% of the total methane released to be captured and fed into pipelines. The aforementioned blasts had a marginal impact on methane emissions and the efficiency of degassing methods. Cyclic drilling and regular switching of boreholes in phase with the mining progress and working face advance were shown to be essential.

Aug 1, 2013

By Guoqiang Lan, Jun Song, Bin Ouyang

Rare-earth pyrochlores, commonly exhibiting anomalously low lattice thermal conductivities, are considered as promising topcoat materials for thermal barrier coatings. However the structural origin underlying their low thermal conductivities remain unclear. In the present study, we investigated the phonon properties of a group of RE pyrochlores, Ln2Zr2O7 (Ln = La, Nd, Sm, Gd) employing density functional theory and quasi harmonic approximation. Through the relaxation time approximation (RTA) with Debye model, the thermal conductivities of those RE pyrochlores were predicted, showing good agreement with experimental measurements. The low thermal conductivities of RE pyrochlores were shown to largely come from the interference between the low-lying optical branches and acoustic branches. The structural origin underlying the low-lying optical branches was then clarified.

Jan 1, 2015

By M. Lindgren

"Hydrometallurgical processing involves process stages, like leaching, that create harsh environment for stainless steels. High acidity, the presence of chlorides and oxidizing ions combined with relatively high temperature create risk for both uniform and localized corrosion. Advanced electrochemical techniques were employed to study uniform and pitting corrosion of two stainless steel grades 316L and 2205. Results obtained with the linear polarization resistance technique combined with the harmonics distortion analysis, electrochemical noise and coupled multielectrode array systems are compared to the results of conventional electrochemical techniques and immersion tests.INTRODUCTIONHydrometallurgical processing has become favoured in metals production in recent years due to energy costs, leaner ore bodies and environmental factors. Because the hydrometallurgical processing route is flexible, various types of secondary raw materials, like flotation tailings, dusts, sludges and slimes can also be treated in addition to conventional mineral concentrates (Sarveswara Rao & Acharya, 2008).Hydrometallurgical processing relies on aqueous chemistry, usually acids, at temperatures around 100°C for the recovery of metals from ores, concentrates, recycled or residual materials. The processing route can typically be divided into three stages: leaching, solution concentration/purification and metal recovery. The processing environment is aggressive, especially in leaching. High acidity, relatively high temperature together with impurities, like chloride ions, place high demands on the corrosion resistance of construction materials. The dominant corrosion mechanism may be uniform corrosion or localized corrosion depending on the process conditions (Ekman & Torsner, 2010). This complicates the prediction of corrosion rates and, consequently, cost effective material selection.Traditional means to evaluate uniform corrosion resistance of stainless steels are immersion tests and the results are published in the form of iso-corrosion diagrams (Outokumpu Stainless, 2010). For the localized corrosion, namely pitting and crevice corrosion, immersion tests can be used but the duration of the test is rather long because an incubation period takes place prior to the occurrence of the actual localized corrosion damage. Electrochemical techniques, traditionally in the form of cyclic polarization scans, have been employed to assess the susceptibility of a material to pitting corrosion (Papavinasam, 2008). They cannot, however, give any indication of the pitting corrosion rate and lack potential for on-line measurements."

Jan 1, 2012

By C-D. Johansson, B. Ögren, B. M. Ludvigsson, K-Å. Johansson, R. Lindh, G. Berg, M. Maliarik

This paper presents the High Current Density (HCD) Silver Electrorefining Process. A 25-year history of development of the silver electrorefining process as well as associated equipment is given. The process is simple and robust, but at the same time highly automated. With low operating costs and man power requirement it allows consistent production of 99.99 % quality cathode silver. The process ensures that no toxic gases are formed in the working environment. Silver Electrorefining is a heart of a Silver Refinery plant covering the complete range of processes from casting of silver Doré anodes to casting of the bars of refined silver or/and silver granulation. The process has been successfully applied at 11 installations world-wide with plant capacities ranging from 30 to 1500 tpa.

Jan 1, 2014

By W. N. Hamilton

"Evaporites abound in the Western Canada sedimentary basin, recurring throughout the stratigraphic column and widely scattered over the basin region. Alberta, situated centrally over the basin, includes many of the evaporites within its borders, but only a few have the right geological conditions to form potential economic deposits of salt or gypsum. These include the Middle Devonian Elk Point Group and related evaporites, Upper Devonian Wabamun Group-Palliser Formation evaporites, and evaporites of the 'Triassic Charlie Lake and Whitehorse formations.Salt deposits underlie almost half of Alberta. The major deposits belong to the Elk Point Group, which includes thick salt units in the Lotsberg, Cold Lake and Prairie Evaporite formations. Another, younger salt deposit in the Wabamun Group has only local distribution. Elk Point salts have a maximum aggregate thickness of 430 m in east-central Alberta. The deposits deepen southwestward across the province, from minimum depths of210 m at Fort McMurray to 1820 m at Edmonton.The thickest, most extensive salt deposits are the upper Lotsberg and Prairie Evaporite salts. Both have excellent development potential. The upper Lotsberg is up to 150 m thick, consists of clear, very coarse crystalline halite with only minor impurities, and has a notable lack of non-salt strata in its succession. Analytical data for the Lotsberg Salt show extraordinary chemical purity. Prairie Evaporite Salt differs lithologically from the Lotsberg in having a significant non-salt component. The deposit is up to 200 m thick and consists of medium crystalline halite, brownish coloured and cloudy as a result of finely dispersed impurities. The main impurities-shale, anhydrite and dolomite-are most prevalent as interbeds in the salt succession, ranging from very thin laminae to beds several metres thick. Although of lesser purity, the Prairie Evaporite Salt is shallower, thicker and more extensive than the Lotsberg and the salt quality is quite acceptable for most industrial uses."

Jan 1, 1982

By N. Morrison, I. Holl, R. Welyhorsky, A. Hempstock

ABSTRACT: The Victor diamond mine is located in the James Bay lowlands, 90 km west of the First Nations village of Attawapiskat. The project was the first of its kind in northern Ontario. The process plant was designed to produce a 95 to 98% by weight diamond concentrate through three stages of comminution, dense medium separation, and proprietary X-ray technology for final recovery. The plant was commissioned over a period of six months, commencing prior to substantial completion of construction. Through effective planning of the commissioning phase, the Victor mine start-up was safely completed nine months ahead of schedule.

Jan 1, 2011

By L. M. Cumming

"The contact between dolomite of the St. George formation (Cambro-Ordovician) and limestone of the overlying Table Head formation (Middle Ordovician) is a regional disconformity. This is best illustrated from exposures on Pointe Riche Peninsula, near Table Point, and along Port au Port Bay. The contact occurs along 180 miles of the west coast of Newfoundland from St. John Island in the north to the western part of Port au Port Peninsula in the south. A disconformity of the same age occurs between the Romaine and Mingan formations on the north side of the Gulf of St. Lawrence.Dolomitic beds beneath the disconformity locally contain concentrations of base-metal sulphides. Sphalerite occurs in dolomite pseudobreccias of the St. George formation at Zinc Lake, 7 miles northeast of Daniels Harbour. The 'Western Newfoundland Lower-Middle Ordovician regional disconformity is interpreted as having originated on and near the edge of a broad platform, and to have provided an important regional geological control in the localization of zinc mineralization."

Jan 1, 1968

By Michael P. Davies

Mine waste facilities, and in particular tailings impoundments, are one of the highest risk aspects of any mining venture. There are far too many recent examples of how real and/or perceived physical or environmental impact from one of these facilities has had enormous economic impact on both the specific project and the overall parent mining company. In many cases, such dramatic impacts have followed a period where a due diligence of the mine had been carried out (e.g. in an acquisition, merger or similar) or an internal or otherwise audit had taken place. Consequently, it is suggested that there is a need for an audit/due diligence framework to assist those processes in terms of assessing mine waste facilities. This paper presents a recommended framework for completing either an audit or due diligence assessment of mine waste facilities under a number of typical scenarios. The framework will be of relevance to reviews carried out prior to mine construction, during operations and for mines that have been in a care and maintenance position and are to be re-opened. Concepts of risk management are introduced as an essential part of the recommended framework. The paper should be of value to current and prospective mine owners involved in stewarding an area of significant risk to viability of their mining venture. The paper should also interest prospective lenders to these ventures.

May 1, 2007

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

By P. L. Drake

This paper comprises a discussion of the role which mineral resources will play in Canada's future export trade and the growing demand for minerals in Canada.

Jan 1, 1979

By T. J. Langan, M. Ramajayam, T. Dorin

"6xxx-series Al alloys are the most commonly used alloys in the automotive industry as they have an appropriate balance of strength, corrosion resistance and formability. The main strengthening phase in these alloys is the ß’-Mg2Si precipitates. One opportunity to achieve stronger 6xxx-series Al alloys, without affecting corrosion and formability, is the use of Sc. The main challenge of using Sc in 6xxx-series lies in the heat treatment, which must be designed to allow for a fine precipitation of both Al3Sc and ß’-Mg2Si. In this work, two model alloys are used, an Al-Sc-Zr and an Al-Mg-Si-Cu-Sc-Zr, to explore the impact of the 6xxx-series key elements (Mg, Si and Cu) on the Al3Sc precipitates. Transmission electron microscopy and atom probe tomography are used to investigate the precipitates present in the microstructure after casting. We find that higher Si content results in the formation of dispersoids upon casting. The average composition of these dispersoids is (Al0.8,Si0.2)3 (Sc0.888,Zr0.024,Mg0.08,Cu0.008). A closer look at the solid solution reveals that most of the Sc and Zr is supersaturated after casting even in the presence of Mg, Si and Cu. We discuss the impact of these results on the design of a suitable heat treatment for 6xxx-series alloys with Sc.INTRODUCTION The most common strategy to strengthen aluminum (Al) alloys is by micro-alloying to form a fine distribution of precipitates (Gladman, 1999). Whilst precipitates enhance the strength, this is often done to the detriment of ductility and corrosion performance (Davis, 1999). The 6xxx-series Al alloys are heavily used in the automotive industry as they offer an appropriate balance of strength, ductility and corrosion resistance (W. S. Miller et al., 2000). The strength increment in these alloys comes from the formation of the ß’–Mg2Si and the quaternary Q’ phase (Chakrabarti & Laughlin, 2004; Polmear, St. John, Nie, & Qian, 2017). One opportunity to achieve stronger 6xxx-series alloys, whilst keeping good balance of corrosion resistance and formability, is the use of small additions of scandium (Sc). Sc is one of the most potent strengtheners in Al alloys (Dorin, Ramajayam, Vahid, & Langan, 2018; Røyset & Ryum, 2005). Most of the strengthening benefits from Sc come from the formation of fine Al3Sc dispersoids. The following strengthening mechanisms apply to Sc: 1) Solid solution strengthening, 2) precipitation hardening, 3) inhibiting recrystallization, 4) assisting nucleation of other strengthening phases (Dorin, Ramajayam, Lamb, & Langan, 2017). As compared to other dispersoid phases, Al3Sc dispersoids have good electrochemical compatibility with Al alloys and hence do not affect their corrosion resistance (Cavanaugh, Birbilis, Buchheit, & Bovard, 2007). The coarsening resistance of Al3Sc is often improved by adding zirconium (Zr), as it forms a Zr rich shell around Al3Sc which prevents Sc from moving across the interface."

Jan 1, 2018

By Edouard Asselin, Tasawar Javed

This study was conducted as a part of ongoing work to characterize sulphide concentrate leach residues generated under CESL (Cominco Engineering Services Limited) and Vale pilot and demonstration plant medium temperature (150 °C) process conditions. Three different samples were analyzed. Derivative samples were prepared by extracting gypsum, sulphur and amorphous/poorly crystalline iron oxyhydroxide phases from the leach residues. Thermal behavior of the samples was studied by thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) in the temperature range 25 to 800 °C in both air and nitrogen atmospheres, with XRD analyses both before and after heating. Thermal transformation temperatures for different iron oxides/oxyhydroxides present in hydrometallurgical leach residues vary over a wide range which suggests the variable crystallinity of the phases. Raman spectroscopic analysis was carried out to help identify the type of iron phases in the residues. Furthermore, hydroxylamine hydrochloride (HaHC) and oxalate extractions were used to compare the fractionation of the amorphous/poorly crystalline iron phases in the residues. Given the compositions of the residues, any thermal events in the temperature range of 200 °C to 480 °C were attributed to amorphous/poorly crystalline iron phases.

Jan 1, 2014

By Joseph Daniels

When Dame Nature shook her horn of plenty and distributed her bounties over the face of the earth, she blessed the Pacific coast with many riches, but with these she added many offsetting disadvantages or handicaps, designed, no doubt, to effect a proper balance between wealth and economy. Nowhere is the application of the law of compensation more aptly illustrated than in the matter of fuel and power resources. A glance at the map of the Pacific northwest will show that west of the Coast Range batholith we are bounteously supplied with coal, with timber, with water power, and with tributary resources of oil from California. Alaska, British Columbia, Washington, all contain large resources of coal; Oregon and California to a lesser degree, but, compensating the golden state for its deficiency in this respect, oil was placed in the treasure ,chest. Timber, of wide variety and in lavish quantity, covers the forests from tidewater to mountain slope, and within this protected watershed area flow streams which give the Pacific coast states the largest single share of the potential water-power resources of the country. Something over 40 per cent. of the total estimated horsepower of the United States is to be found in the Pacific states, and British Columbia has 15 per cent. of the total for Canada; but of this total less than 10 per cent. has been developed.

Jan 1, 1924

By W. G. Hatch

Introduction In November, 1927, a paper was presented at the Annual Meeting of the British Columbia Division by H. A. Pearse(l), in which he described the milling practice at Britannia and set forth the metallurgical results which were being obtained at that time. In the intervening four years, various changes and additions have been made in equipment and practice, which have resulted in marked improvements in efficiency and costs. These changes and their effects are discussed in the present paper. During the past few years two major changes have been made in plant equipment. The first of these was the. elimination of an intermediate crushing stage by discarding two gyratory crushers in favour of two Symons cone crushers. The latter installation-now effects in one stage a greater reduction than was formerly accomplished in two, that is, by the gyratories together with a set of rolls. The second important change in equipment took place when the original M.S. flotation machines were replaced by six Forrester pneumatic machines, so that now the flotation department consists entirely of machines of this type. A number of minor changes and some further additions to equipment have also been effective in raising plant capacity and concentrate grade, while making noticeable reductions in tailing losses and costs of ore treatment.

Jan 1, 1932

By D. S. Salonine

Aluminum alloys offer a wide range of capability with a unique combination of advantages that makes them the materials of choice for numerous products and markets. One of the most important applications is their use as the primary structure and outer envelope in aerospace vehicles. Wide and thorough studies on hot working and microstructure evolution of aluminum alloys have been made in Russia. The most important appear to be: - introducing the structure diagrams in strain rate - temperature coordinates which show areas of different microstructures (non-recrystallized, recrystallized, and mixed) after the hot deformation and the following heat-treatment for common aluminum alloys (Yu.M. Vainblat); - studying the press-effect ("structural effect" by V.I. Dobatkin); - learning the influence of hot worked substructure on aging mechanisms; conducting researches on press heat-treatment. These works allowed a deeper understanding and a better control of the mechanical behavior of aluminum products. Comparisons are made to equivalent developments in Europe and America.

Jan 1, 2004

By David Stone

North American Palladium is the owner/operator of the Lac des Iles mine located 115 km north of Thunder Bay, Ontario. The mine has produced an average of 65,000 ounces of palladium since 1994. Lac des Iles is currently undergoing the first phase of a major expansion that will increase ore production from 2,400 tons per day to 15,000 tons per day. A future expansion is being contemplated for 30,000 tons per day. The current expansion will increase palladium output to 250,000 ounces per year. The mine plan for the ultimate pit results in an excavation 1 km long by 800 m wide and over 450 m deep. This makes the ultimate pit at Lac des Iles one of the ten deepest open pits in the world, and the largest in Canada. This paper outlines the geotechnical data collection and design methodology for the ultimate open pit at Lac des Iles.

May 1, 2001

By H. A. Halupka, I. A. Mozer

"At its plant in San Juan, Peru, Marcona Mining Company operates two grate pelletizing furnaces for the agglomeration of 3.5 million long tons of magnetic concentrates annually. Line One, installed in 1963, was built by Lurgi as a downdraft process furnace utilizing a furnace fan for the recuperation of hot gases from the cooling zone. This line was modified in 1966 to include both updraft drying and downdraft drying, and the original roof burners were converted to side-wall burners. Line Two, a Dravo-Lurgi furnace with an annual capacity of 2.4 million long tons, was built in 1966. This line, in contrast to the modified Lurgi furnace, employs direct recuperation of hot gases from the cooling zone and utilization of process gases from the firing zone for updraft drying.At its plant in San Juan, Peru, Marcona Mining Compa-ny operates two grate pelletizing furnaces for the agglo-meration of 3.5 million long tons of magnetic concentrates annually. Line One, installed in 1963, was built by Lurgi as a downdraft process furnace utilizing a furnace fan for the recuperation of hot gases from the cooling zone. This line was modified in 1966 to include both updraft drying and downdraft drying, and the original roof burners were converted to side-wall burners. Line Two, a Dravo-Lurgi furnace with an annual capacity of 2.4 million long tons, was built in 1966. This line, in contrast to the modified Lurgi furnace, employs direct recuperation of hot gases from the cooling zone and utilization of process gases from the firing zone for updraft drying. 5 per cent increased capacity, 30 per cent lower fuel oil consumption, and approximately 400 per cent reduction in grate bar and pallet corrosion. Firing of the pellet bed was improved by conversion from roof to side-wall burners. This modification also permitted utilization of monolithic refractory in place of pre-fired shapes, thereby improving over-all furnace availability and reducing refractory stock requirements from 154 different shapes to 18.Data are presented to compare operating performance of the Dravo-Lurgi furnace and the modified Lurgi furnace. These data show 30 per cent lower fuel oil consumption and 10 per cent higher capacity per unit grate area for the Dravo-Lurgi furnace, which also averages higher availability due to greater operating flexibility."

Jan 1, 1970

By S. E. Jackson, L. J. Cabri

Quantitative determination of gold at sub-ppm concentrations in sulphide minerals is an important component of deportment studies for sulphide-gold deposits. Laser Ablation Inductively Coupled Mass Spectrometry (LA-ICP-MS) analysis is preferred for this application because it rapidly and cost-effectively provides spatially resolved (<20 pm), low ppb concentration data for gold and other elements in mineral grains. Recent advances in LA-ICP-MS analysis include the development and application of elemental mapping. Raw signals from multiple line scans or lines-of-spots are deconvoluted and calibrated to generate elemental maps which provide detailed information on spatial variations of gold and other elements within and between grains.

Jan 1, 2011

?Podolsky Water treatment plant discharges to Norman North bog which drains into Whistle / Post Creek watershed and into Wanapitei Lake ?Whistle Mine closed and reclaimed but continues to treat and discharge water to Whistle Creek

May 1, 2009

By I. R. Muirhead

"One approach to making new technology available is to demonstrate its value under full-scale operating conditions. Studies were undertaken to assess the feasibility of this approach to introducing a longwall mining system to the western Canadian coalfields.The longwall method of mining coal is described, world and Canadian usage is reviewed, and the merits of the system in comparison 10 other coal mining methods are discussed.The rationale for a longwall demonstration in western Canada is presented, along with a proposed organization for the design, operation and dissemination of the findings from such a trial. The factors which must be considered in the design of the demonstration, and in the assessment of a potential site are highlighted. It is concluded that a demonstration of this technology is both timely and essential to prepare the way for the western Canadian coal industry of future prospects for coal.IntroductionFor many years CANMET has encouraged research work organized on a cooperative basis. This requires that a working consensus must be negotiated by researchers and operators at the beginning of the project and continuously refined as work proceeds. The result is usually a more relevant selection of research problems, improved direct ion and con duct of experiment al work and often a validation phase in which research concepts are tested in an opera ting environment. All this tends to narrow the gap between obtaining research results and applying them.Even under the best of circumstances cooperative projects require a good deal of coordination and enthusiasm to maintain focus and the pace of work. The working perspective of a research scientist in a government laboratory is substantially different from that of a mine operator at a producing mine, and a common ground must be found. This is difficult to do and cooperative projects typically evolve over several years as experimental results progressively define the potential solutions to mining problems."

Jan 1, 1985