Search Documents

By G. H. Charlewood, J. W. McBean

"One hundred years after being developed, the diamond drill is still an essential tool in mineral exploration. The basic principle is unchanged, but the technique has been revolutionized, particularly in the past fifteen years. The cost of core drilling has not kept pace with the rising cost of living. The price of machinery, supplies and labour in drilling has doubled and trebled since 1946. Some of the techniques which have made it possible to hold the price line are described."

Jan 1, 1967

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By D. W. Euler, D. G. Brophey

"In an attempt to address the issue of rising labour costs, and to improve productivity, a laser-based system to guide underground LHDs and trucks has been developed. This comprehensive system is known as the Opti-Trak system.Essentially, the vehicle is equipped with front and rear-mounted lasers which scan a reference strip mounted on the drift back. The vehicle follows this reference strip and in addition, based on reflective bar codes mounted beside the reference strip, initiates certain functions (i.e. dump cycle, speed change, brake check, etc.). Any programming that is drift-specific is handled by the positioning of the reference strips and bar codes. Consequently, the vehicle can easily travel to many different haulageways or branches, providing the reference strip and bar codes are in place.The advantages of this system are an immediate elimination of haulage operator costs and an increase in available hauling time to 7 hours out of an 8-hour shift as compared to the typical 5Y2 out of 8 hours that a manned haulage system offers.This paper describes the Opti-Trak system and the benefits to be realized from automation of mine haulage requirements."

Jan 1, 1994

By G. A. Vissac

IN THE preliminary design of a coal washery, the most important factor to evaluate is the ash content of the final product. The ash content permissible may be imposed by market demands, but, in the final analysis, sooner or later - as most consumers today are buying coal on a 'heat value' basis - the coal operator has a certain margin of latitude. and the ash content of the coal to be delivered can be determined on the basis of maximum returns and highest profits. A few years ago, the most desirable separation was selected on the basis of the plus-minus 0.10; that is, the most desirable gravity of the separation was selected at the point showing a minimum amount of near gravities in the raw coal. The reason for this was an expected wide error over these near gravities. Today with the recent development of cry accurate, automatically controlled cleaning apparatus, a much larger latitude is possible, and the most desirable gravity of separation can be selected, almost exclusively, on the basis of the economic factors involved. To illustrate these new methods of investigation we shall give two examples, based on actual coals from the western United States.

Jan 1, 1957

By L. Lariviere, M. Grenier, R. Khalili, D. Shook

A mineral processing facility near Montreal, CEZinc, Noranda Inc., has recently implemented a leading-edge intranet solution for monitoring the performance of plant operations, and providing condition-based maintenance. This innovative multi-faceted software implementation incorporates: web-delivered plant information systems; area-wide control loop performance assessment (using sophisticated algorithms to evaluate poorly performing controllers); and integrated alarm management functions.The system has enabled a project to improve plant operations through better process control. Maintenance technicians, engineers, supervisors and managers all can see the performance of the controllers, and the performance of the plant itself, through webdelivered graphics and reports. Information is combined from many sources, real-time, historical, relational and analytical, to provide a complete picture of plant operation.The web-based solution centralizes the administration of user access, and simplifies the deployment of several different kinds of information to many desktops. It is an extensible system that allows users to create and share their own web pages and data views.The paper will discuss the solution architecture and the improvements the IT, operations, maintenance, and engineering groups have experienced, and overall benefits to the facility.

Jan 1, 2003

By A. R. Miller, G. Desrivières, M. C. Bétournay, D. L. Barnes, P. Laliberté

"Over the last four years, an international initiative, championed by Vehicle Projects LLC, the Fuelcell Propulsion Institute and Natural Resources Canada, has been active in carrying out research projects to prove out the concept of applying fuel cell technology to underground mining vehicles. These have been carried out by a consortium consisting of mining companies, equipment manufacturers, technology developers, national laboratories and consultants, with the participation of Canadian and U.S. mine regulatory agencies.This clean technology, which produces only water and electricity, would allow several advantages to be obtained, in the health area (by eliminating diesel emissions and reducing noise generation), in lowering production costs (such as reducing ventilation required) and lowering greenhouse gas emissions.This paper outlines the results obtained in several key areas, such as, the operation of fuel cells in underground conditions, risk issues related to underground and surface operation of hydrogen vehicles and hydrogen production and delivery systems, and the design and mining performance of the world’s first hydrogen mining vehicle, a mine production locomotive. The work to date on the fuel cell loader, designing the power plant and power transmission systems, operational requirements, and operating cost reductions is also presented."

Jan 1, 2003

By K. Barbetti

"The carbon-in-pulp (CIP) process has been the dominant gold recovery process since the early 1980s. CIP has proven to be very adaptable for a wide range of ores and circuit configurations. The key performance indicator for CIP circuits is the minimisation of soluble gold losses to tailings, however, it is also important to operate the circuit efficiently (maximising gold loadings on carbon and minimising carbon inventory). Over the last 30 years the Curtin Gold Technology Group has studied CIP circuits as part of an on-going collaborative industry funded project (the AMIRA Gold Processing Technology Project). In the early years the project undertook basic research into understanding activated carbon, and its management in the circuit. More recently the development of process models and instrumentation has provided additional tools to assist operators. The results show that while most CIP circuits operate well, there are still significant opportunities for further cost savings, or additional revenue. This paper reviews the observations arising from this work, including key requirements for good carbon management, the results of benchmarking and industry surveys of carbon circuit over 20 years, the value of process modelling of CIP circuits to establish operating parameters, and the use of automated instrumentation to better optimise carbon control in the circuit.INTRODUCTION The introduction of activated carbon to recover gold from cyanide leach solutions in the last quarter of the 20th century was the most significant development in gold ore processing since the advent of cyanidation seventy years before. Replacing the Merrill–Crowe zinc cementation step with carbon-in-pulp (CIP) or carbon-in-leach (CIL) circuits provided a process that allowed the treatment of lower grade and problematic ores (e.g. high-clay ores), at lower capital and operating costs, and higher metal recoveries. The CIP circuit was first developed in the 1950s at the Carlton Mill, Cripple Creek, Colorado. All the components of the modern CIP process came to fruition at the Homestake Mine in South Dakota in 1973 (Fast, 1988). From the late 1970s onward a variation of CIP, carbon-in-leach (CIL) which combined the leach and adsorption stages, became the preferred circuit design in most parts of the word."

Jan 1, 2017

By R. Charlier, G. Radioti, J. -P. Radu, S. Delvoie, F. Nguyen

"In order to investigate the fracturing of the bedrock and its possible heterogeneous distribution in situ, four boreholes equipped with double-U geothermal pipes of 100 m long were installed on the campus of the University of Liege (Liege, Belgium) over a surface area of 32 m². The bedrock, which starts at a depth approximately of 8 m, is quite fractured and consists mainly of siltstone and shale interbedded with sandstone.Different geophysical methods are applied at two different phases, after drilling the boreholes and after injecting the grouting material. The first approach consists in lowering an ultrasonic borehole imager (borehole televiewer; Zemanek, Glenn, Norton, & Caldwell, 1970), an instrument that acts as an ultrasonic transducer and receiver, into the boreholes to obtain high-resolution, continuous images with 360° coverage of the local geology and fracturing. Moreover gamma-ray logs of the four boreholes are obtained and inclinometry is conducted.After drilling the boreholes fiber optic cables are attached along the pipe loops and the double-U pipes are installed inside the boreholes. Then the grouting material is injected. The second approach consists in measuring the temperature along the fibers by applying the Distributed Temperature Sensing technique (Soto, Sahu, Faralli, Bolognini, Di Pasquale, Nebendahl, & Rueck, 2007). A laser pulse is injected into the optical fiber and the temperature along the fiber is determined by the intensity of Raman stokes and anti-stokes reemitted signals. Temperature evolution is measured during hardening of the grouting material. Local maxima of the temperature curve are probably due to a local lower thermal conductivity and/or a local larger quantity of grouting material due to gathering of fractures.A detailed fracture characterisation (position, opening, orientation, dip angle) is obtained based on the acoustic signal travel time and amplitude. The fractures are characterised by the same dipping and orientation but significantly vary in number and location in the four boreholes, despite the close distance between them. Gamma-ray data and observation of the cuttings during drilling result in rock identification through depth as well as in determination of the layer dipping. The inclination of the four boreholes tends to be perpendicular to the dipping. The combination of the two geophysical methods as presented provides information useful for the hydro-thermo-mechanical behaviour of the bedrock. The contribution of the thermal behaviour of borehole heat exchangers to bedrock investigation will be further studied by conducting Distributed Thermal Response tests (Fujii, Okubo, & Itoi, 2006). During the tests we will measure the temperature variation thanks to the installed fiber optics. These data will allow us to correlate any anisotropic thermal behaviour to the geological characteristics. The available information could be used for a detailed numerical model."

Jan 1, 2015

By N. W. Bliss

"Bauxite has been the almost universal ore of aluminum for about 100 years, with most of the world's reserves oc¬curring in the developing countries. As a result of fiscal and political activities prompted in part by the energy crisis, the formation of the IBA combined with increasing freight and labour costs, these reserves are no longer as competitive or as secure as they once were. This has given fresh impetus to the development of processes for alumina production that utilize raw material other than bauxite. Canada has no bauxite and it is prudent to look for alter¬native raw materials within our own boundaries suitable for one of these processes.Of the three igneous rocks that have been used as a source of alumina, only anorthosite is considered as a potential source in Canada. The Al content would be extracted by a sinter process, which currently requires a raw material with a. minimum of 28% Al2O2. Thus, about 4 tons of anorthosite and 10 to 12 tons of limestone are needed to produce one ton of alumina. There are two petrologically distinct types of anorthosite, one containing the plagioclase andesine-labradorite and around 26% Al2O3, and the other containing upwards of 30% Al2O3, in by¬townite-anorthite; for our purposes they may be con¬sidered as low- and high-alumina anorthosite respectively. The high-alumina anorthosites are somewhat rare; the low-alumina anorthosites are much more common, partic¬ularly in Eastern Canada. Geologically speaking, there is no shortage of anorthosite in Canada. The reserves are im¬mense, although their low Al2O3 content coupled with con¬siderations of location, access and proximity to limestone could be constraints to their development. Fly ash from coal-fired thermal power stations and nepheline syenite can also be used in a sinter process, but neither is likely to be utilized in Canada in the immediate future.The H+ process utilizes an acid attack to leach Al from a raw material with at least 20% Al2O3. One of the best raw materials is kaolinite-bearing clay; not only is it high in Al, but most of it can be extracted. With the possible exception of the Whitemud clay in Saskatchewan, Canada is apparently deficient in clays with sufficient reserves to support an alumina plant utilizing the H+ process. Low-alumina clays with illite and montmorillonite may also prove to be a suitable raw material if advantageously sited with respect to industrial centers. The average shale con¬tains only 15% Al2O33, much of which may be contained in minerals, such as feldspar, not amenable to acid leaching. If shale is used as a source of alumina, it will be because it contains some other valuable commodity, such as oil or uranium, the extraction of which leaves the spent shale upgraded in extractable Al2O3 and lowers the over-all costs to a point where it is economic, Thus, rejects from coal washing plants are most commonly considered as a source of alumina; they are already mined, are available in large and ever increasing amounts, and may contain significant amounts of combustible material which upgrades the Al2O3, content of the resulting ash. Coal rejects from existing and developing coalfields in Alberta and British Columbia are a possible source of raw material, but present data indicate they may contain insufficient Al2O3."

Jan 1, 1976

By D. D. Tannant

An experimental and numerical study was conducted on the geomechanical behaviour of oil sands during penetration tests in which a steel wedge with an apex angle of either 20 degrees or 30 degrees was forced into compacted oil sands. The boundary conditions simulated in the laboratory tests are similar to shovel penetration into oil sands. The objective of the laboratory tests was to measure the force required to push a steel wedge into compacted oil sands. A wedge penetration test differs from conventional triaxial tests in that much more shear is generated. The laboratory data was needed to improve calibration of micro-mechanical input parameters for a two-dimensional discrete element model of oil sands constructed with Particle Flow Code (PFC). Initial model calibration was performed with triaxial test data and then a PFC model of the wedge penetration test was constructed. The measured force-displacement behaviour of the steel wedge was compared with PFC modelling results. It was found that different combinations of PFC particle and bond parameters could equally well replicate the laboratory triaxial compression data for bitumen-rich oil sands. When the wedge model was run, it was found that the resulting force required to penetrate the wedge into the oil sands was about four to six times higher than that measured. This clearly indicates that further research is required to improve the predictive capability of PFC models of oil sands.

Jan 1, 2002

We report the studies of Proton-Exchange Membrane Fuel Cells (PEM FC) and hydrogen storage materials at McMaster University for the last 14 years. From the initial investigation of ionic conduction mechanism to the revelation of the origin of non-Arrhenius temperature dependence, as well as the synthesis and characterization of high temperature polymer electrolytes, both experimental and theoretical works have been compiled for the fuel cell membranes. In addition to the discovery of suppressed ionic conduction in Electrode-Membrane Assembly (EMA) and novel hydrocarbon PEMs based on micro-emulsion, the first evidence of hydrogen adsorption saturation by carbon nano-tubes was also achieved, which has been the bottleneck for the application of PEM FC. Prior to our study, a number of controversial publications have claimed the hydrogen capacity of these materials to be between 0.1 to 10.0 wt.%, and none demonstrated a plateau of adsorption with pressure that is consistent with monolayer saturation. Others suggested that the tube bundle structure is opened under high pressure to enable higher adsorption on newly uncovered surfaces, but received no confirmation. Using our home made high-pressure instrument with in-situ electrical probes, we found that a plateau is nearly achieved at about 300 atm in the room temperature isotherm, and that nanotube bundles actually compress with pressure instead of splitting, using in-situ electrical measurements.

Jan 1, 2005

"Developed by CRIRSCO, IRT is a document that draws on the best of the CRIRSCO-style reporting standards. These reporting standards are recognised and adopted world-wide for market-related reporting and financial investment.The IRT is not an international reporting code and does not supersede existing national reporting standards. Rather it is a guideline that encapsulates the content of these standards for the benefit of the international mining industry and its various stakeholders.The template is a 'living document' that is continuously updated and improved as new national laws, rules, codes and guidelines are created or amended.The International Template is advisory only and where national codes already exist, these will take precedence. The International Template is intended to assist those countries that either do not have a reporting code or whose code is outdated, to produce a new code consistent with international best practice. It also provides a consolidated version of national codes that reflects their compatible international components and may thus be used in comparisons with other international reporting systems. The word 'Template' is used advisedly to indicate that this document is a model for code development and does not in itself constitute a 'code' which implies that it has legal or other regulatory force.From this point forward, the Template includes words that imply a mandatory action, such as ""requires"", ""applies"", ""must"" etc. This is to enable the Template to be easily adopted by countries and organisations wishing to do so, and does not imply that the Template itself is a mandatory reporting standard.INTRODUCTION2 In this edition of the International Reporting Template (""The Template""), important terms and their definitions are highlighted in bold text. The guidelines are placed after the respective Template clauses using indented italics. They are intended to provide assistance and guidance to readers for interpreting the application of the clauses in the Template.Indented italics are also used for Appendix 1 — 'Generic Terms and Equivalents"", and Table 1 —'Check List of Assessment and Reporting Criteria' to make it clear that they are also part of the guidelines for the application of the Template.Appendix 1 contains a table of generic terms and their equivalents, designed to avoid unnecessary duplication or ambiguity in the textAppendix 2 provides Rules of Conduct for Mineral Resource and Mineral Reserve estimators that may be considered in addition to the Codes of Ethics or Practice normally applying to members of professional institutions."

Jan 1, 2003

Mining Subscribes to Murphy?s Law Personal observations on the past ?Perfect, benign deposit mines can be screwed up-spills and concentrate handling issues ?Long term contamination and water management assessments inadequate ?The ?permitting mentality? and its effects on the application of proponent and regulator resources ?Reliance on simple principles but nature and chemistry is more complex

May 1, 2010

By Dale A. Sketchley

The objective of Quality Assurance and Quality Control programs on advanced exploration projects is to ensure that data from sampling, assaying, and recording of geological observations are of high integrity for the purpose of obtaining reliable mineral resource and reserve estimates. National Instrument 43-101 Standards of Disclosure for Mineral Projects states that all scientific and technical reports must be prepared and certified by a Qualified Person in accordance with professional and industry standards following Mineral Exploration Best Practices Guidelines and Definitions, and Guidelines of the CIM Standards on Mineral Resources and Reserves. Additional information is given in Companion Policy 43-101CP and Technical Report Form 43-101F1. Although the Qualified Person must discuss and describe the Sampling Method and Approach; Sample Preparation, Analyses, and Security; and Data Verification; there is little specific information in the guidelines on Quality Assurance and Quality Control programs. Examples from the Oyu Tolgoi Cu-Au Project are given for optimizing sampling protocols, following proper sample preparation procedures, safeguarding sample shipments through chain of custody, ensuring quality of assaying with Round Robin monitoring programs, verifying transcribed data, and validating data with check assays to ensure high integrity for resource and reserve estimation. Oyu Tolgoi, also known as Turquoise Hill, is in the South Gobi desert, Mongolia, about 550 km south of the capital city of Ulaanbaatar, and 875 km northwest of Beijing, China. The project covers a major copper-gold system, which consists of the South West, South, Central, and Far North deposits, comprising high sulphidation and porphyry mineralization with oxide, supergene, and hypogene ore types. Exploration is done by multiple diamond drill rigs, and samples are prepared on-site and shipped to laboratories in Mongolia, Canada, and Australia for further preparation and analysis.

May 1, 2003

By H. J. McQueen

Before 1950, hot working was simply deforming above the recrystallization point and gave a soft product compared to cold working. From 1960 onwards, improved testing in compression and torsion (stress, strain rate, temperature, quenching) provided valid specimens for microstructural analysis by polarized optical and transmission electron microscopy (TEM). Indeed, TEM was essential to uncovering the hot working mechanisms because it could distinguish between cold and hot substructures (dynamic recovery) in either initial or new grains (dynamic recrystallization). Over the years, teams at Concordia, McGill and UBC obtained NSERC support for students and equipment. CANMET built up a hot forming group having capabilities from high-rate cam-plastometer compression to rolling of experimental alloy billets; this was combined with latest metallographic instruments for fundamental research. Al alloys of every class (2000, 3000, 5000, 7000, 8000) were studied to understand the effects of solutes, precipitates, dispersoids and composites. The complex flow patterns in extrusion were clarified and modeled by finite element methods. Physical simulations of rolling schedules (up to 20 passes and reductions of 98%) by torsion provided evidence of microstructure development during both the passes and the softening intervals, thus clarifying development of texture in different alloys. The results frequently appeared in proceedings of Light Metals symposia and Canadian Metallurgical Quarterly

Jan 1, 2011

"The Companion Policy is guidance and not law. It sets out the views of the Canadian Securities Administrators (CSA) at to the manner in which the CSA interprets and applies certain provisions of NI 43-101 and Form 43101F1. The Companion Policy references the CIM Best Practice Guidelines for Mineral Exploration, and the Mineral Resources and Mineral Reserves, and that they should be followed by Qualified Persons.COMPANION POLICY 43-101CP TO NATIONAL INSTRUMENT 43-101 STANDARDS OF DISCLOSURE FOR MINERAL PROJECTS This companion policy sets out the views of the Canadian Securities Administrators (the “CSA”) as to the manner in which the CSA interprets and applies certain provisions of National Instrument 43-101 and Form 43-101F1 (the “Instrument”), and how the securities regulatory authorities or regulators (the “Securities Regulatory Authorities”) may exercise their discretion in respect of certain applications for exemption from provisions of the Instrument. PART 1 APPLICATION AND TERMINOLOGY 1.1 Supplements Other Requirements – The Instrument supplements other continuous disclosure requirements of securities legislation that apply to reporting issuers in all business sectors. 1.2 Evolving Industry Standards and Modifications to the Instrument- Mining industry practice and professional standards are evolving in Canada and internationally. The Securities Regulatory Authorities will monitor developments in these fields and will solicit and consider recommendations from their staff and external advisers as to whether modifications to the Instrument are appropriate. 1.3 Application of the Instrument -The definition of “disclosure” under the Instrument includes oral and written disclosure. The Instrument establishes standards for disclosure of scientific and technical information regarding mineral projects and requires that the disclosure be based on a technical report or other information prepared byor under the supervision of a qualified person. The Instrument does not apply to disclosure concerning petroleum, natural gas, bituminous sands or shales, groundwater, coal bed methane or other substances that do not fall within the meaning of the term “mineral project” in section 1.1 of the Instrument. 1.4 Mineral Resources and Mineral Reserves Definitions - The Instrument incorporates by reference the definitions and categories of mineral resources and mineral reserves as set out in the Canadian Institute of Mining, Metallurgy and Petroleum (the “CIM”) Definition Standards on Mineral Resources and Mineral Reserves (the “CIM Definition Standards”) adopted by the CIM Council on November 14, 2004, as amended. 1.5 Best Practices Guidelines for Mineral Resources and Mineral Reserves - A qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow the CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines adopted by CIM on November 23, 2003, as amended. These guidelines are posted on www.cim.org."

Jan 1, 2003

By Dong-min Lee

As the construction industry is becoming more large-scaled and complex, the BIM technology has been utilized throughout the industry. Since 2008, the construction industry in South Korea (Korea) has required carrying on BIM-based project continually. According to this trend, BIM S/W market, as well as BIM library market is also gradually activated. Many countries have already been establishing Web-based BIM library market, also Korea has been trying to establishing this Web-based BIM library market. In this study, through market research of Web-based BIM library market of advanced countries including the U.S.A. and U.K., establishment strategy of BIM library market to be derived by late starters that introduce BIM such as Korea, Japan and China was deduced based on current establishment status of BIM library market in Korea. In addition, deal with an issue that a clear revenue-sharing system between business principals of Web-based BIM library market is not available at the current stage was presented as a factor of inhibiting activation of BIM library market. So in order to offer a reasonable revenue-sharing strategy in BIM library market as conceptual level, a methodology and process of applying Game theory being used for deriving. It is expected that a reasonable revenue-sharing model between business principals would be presented as its standard of BIM library market to be more activated in the future.

Aug 1, 2013

By M. L. McAllister, M. Veiga

The mineral industry has seen many significant changes in the past decade. Increasingly, it has responded to unanticipated pressures and demands with a variety of voluntary initiatives. Yet there is still much to do. Mining now takes place in a different context than was the case in the past. Socio-economic, political and environmental considerations must now be integrated into traditional mining systems. This process of integration needs to involve industry, governments, academics, communities and other stakeholders to design a new approach to mining, one that can be fostered through interdisciplinary links and holistic strategies. This paper considers the meaning of sustainability in the context of the Canadian mining industry and explores the need for a broader vision for the mining industry. The role of technology is then analyzed and related to an initiative recently taken by Canadian universities to develop a national network for interdisciplinary research into sustainable mining, CaSM.

Jan 1, 1999

By S. D. Botts, F. Cantuarias

"The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd., is a $2.3 billion copper/ zinc project, located in the Ancash Department of Peru. The project consists of an open pit mine, a 70 000 ton per day concentrator, a 302 km long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 Mtpy of copper and zinc concentrates over a 23 year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world.This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14, 2001 by Peruvian president Alejandro Toledo.The construction stage of the project generated 8000 direct jobs, with a peak of 10 000 employees, and 30 000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals, around 30% of whom came from the region where the deposit is located. Approximately 5600 indirect jobs were generated from the project. Independent sources state that Antamina increased the Peruvian mining exports by 30% (mining exports constitute 50% of Peru’s total exports) and Peruvian GDP by 1% in its first year of full operation in 2002.Since winning the privatization bid for the project in 1996, the company has implemented an approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company’s environmental program.Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues and, as a result, has set new standards in Peru for environmental and community management and sustainable development."

Jan 1, 2003

By Paul R. Terry

This paper presents a brief picture of the quality of coal produced in Eastern Canada for use in thermal generating stations. It describes, in particular, the characteristics of coals burned in six power plants -two in New Brunswick and four in Nova Scotia. Each station is dis-cussed in turn, and comments are made on the coals used therein with regards to origin and physical and chemical properties affecting station operation. A table of coal data shows, at a glance, the wide variation in the quality of coals received by these stations from producers in New Brunswick and Nova Scotia. "The promotion of improved coal quality for thermal generation can benefit our national economy." T HIS is the opening statement in a paper which was presented by Mr. D. A. Pirttinen at the Coal Division's Toronto meeting in April, 1960. In bringing the power engineer's viewpoint to the coal producers' attention, Mr. Pirttinen made a survey of utility steam plants operating in Canada, and the results of this survey formed the basis for his paper, which he titled: "Generating Station Coal Quality.

Jan 1, 1965