Search Documents

By Stein A

The general mechanism of recrystallisation for cold worked metal is well established, and need be only briefly summarised with a few references to recent articles which clarify minor points. The types of extension, whether by stretching, drawing, hammering, rolling, etc., do not alter the general principles (1), although quantitative results may differ somewhat, particularly with regard to differences between the surface and interior of samples.These principles can be summarised as follows: The first stage in annealing is a recovery (sometimes known as relaxation) of physical properties such as hardness, elongation, etc., without any appearance of recrystallisation; the second stage involves a further alteration in physical properties, accompanying the formation of new recrystallised grains which replace the original structure; a possible third stage involves an increase in the grain size of the completely recrystallised structure by absorption of smaller grains by larger ones. These three stages will be referred to as recovery, recrystallisation, and grain growth. Depending on conditions, the three stages may be clearly marked or may occur more or less simultaneously.For a given annealing temperature, cold deformations below a certain amount fail to give recrystallisation, and the final structure consists of the original grains which have recovered and possibly become more equiaxed. When a certain deformation, critical for that annealing temperature, is given, recrystallisation can occur, and will give the maximum recrystallised grain size.Increasing deformations beyond this give progressively smaller grain sizes.For each material there is a minimum recrystallisation temperature, below which recrystallisation will not occur whatever the deformation or time of annealing. For a given deformation there is a temperature, critical for that deformation, below which recrystallisation will not occur, and above which it will take place with increasing rapidity.

Jan 1, 1947

By Slechta JJ

The performance of a hydrocyclone treating fine coal has been examined over a wide range of feed and operating conditions.The results were expressed in terms of partition curves from which the water split to the oversize flowstream,the corrected separation size and reduced partition curves were determined-.The following conclusions were obtained. (a) The water split to the oversize flowstream was found to be dependent upon the vortex finder and spigot diameters of the cyclone and the flowrate and solids content of the feed slurry. (b) The corrected separation size was dependent on the solids content of the feed,and the vortex finder and spigot diameters.The hydraulic pressure (or flowrate) of the feed slurry did not have a significant effect.This phenomenon could be explained in terms of crowding of the particles at the Spigot.

Jan 1, 1984

The mineral pulp as it passes through grinding-classification, flotation and solid-liquid separation is examined in the context of it being a particulate fluid. By focussing on the complex viscosity and yield stress of the fluid, new control strategies are discussed. The mineral-particulate fluid is dominatred by non-Newtonian rheology (ie shear thinning, shear thickening, shear yield stress and compressive yield strength). The control of this Theology is seen to be dependent on the fundamental practice-particle interaction forces and with adequate information, it is possible to use the complex shear properties to advantage. The advantages, in terms of final waste and concentrate management, to high weight per cent solids in the mineral particulate fluid, are explored and control strategies outlined.

Jan 1, 1993

Hindustan Zinc Limited (HZL) is one of the leading base metal producers in India. It operates a two-smelter Complex at Visakhapatnam, Andhra Pradesh. At this zinc-lead smelter zinc is manufactured by the conventional hydrometallurgical route and lead is produced by Blast furnace technology generating residues or wastes which contain substantial quantities of metal values. Disposal of such wastes is a problem in any non-ferrous industry. Both the stringent environmental regulations and the changing industrial scenario emphasise the need for industrial research to find economically viable and environmentally friendly technologies to recover the metal values from these waste materials. The in-house R&D Centre at Vizag Zinc Smelter (VZS) thinking globally re-engineered its activities and major thrust was given for converting waste to valuable metals and metal compounds. Basic analytical chemistry with the hydrometallurgical concepts has been adopted in developing these innovative technologies. In this paper attempts are made to provide a clear history of the different waste raw material, the process developed for each raw material and their superiority of over other parallel work. Most of the processes described here are pilot plant tested and under patenting. The process flowsheet, results obtained and advantages of each process are presented. This paper provides a consolidated approach through which the varied smelter waste materials can be processed with cost effective and eco-friendly innovative technologies. In-house R&D efforts at VZS with its contribution and achievement in converting æwastes into wealthÆ technologies are presented in this paper on the following the major thrust areas:recovery of zinc from liquid effluent; recovery of zinc from effluent treatment plant (ETP) gypsum sludge; production of highly pure electrolytic zinc metal powder from zinc bearing gypsum residue/sludge generated at the effluent treatment plant; hydrometallurgical recovery of copper as copper sulphate solution which can be used for CuSO4.5H2O, copper cathode/copper metal powder from copper-cadmium cement; recovery of manganese, lead and silver from anode mud generated at Zinc Cell House and 4-metal extraction/recovery of manganese, cobalt, copper and nickel from Indian ocean bed manganese nodules; recovery of zinc, lead, silver and sulphur values from silver concentrate residue generated at the froth flotation process; recovery of silver and lead as lead-silver sponge/lead-silver sulphide concentrate from lead bearing residues; recovery of lead, silver and copper from copper matte; recovery of antimony as antimony metal or lead-antimony master alloy from antimony bearing dross; and recovery of nickel and dimethylglyoxime from Ni-DMG complex.

Jan 1, 2000

The mine planning and operational aspects of applying Continuous Surface Miner (CSM) technology to Australian coal strip and open cut mines is investigated for both existing and planned deposits. CSM produc- tivity as a function of geomechanical properties, formation thickness, mechanical availability and in-pit physical constraints, are considered. Productivity and operational costs are derived from current production machines and from first principles.

Jan 1, 1989

The South Comet mine is an underground silver-lead-zinc mine located on the West Coast of Tasmania with an annual production in the order of 35 000 tonne per year. All ore mined is shipped to the Rosebery mill by road, a distance of 17 km.

Jan 1, 1993

Interaction between rock and fluid plays a critical role in rock engineering ventures such as stimulation of oil and gas wells, geothermal energy recovery and nuclear waste isolation. Robust and reliable design of the related services and underground facilities is based on understanding of the mechanics and chemistry of the coupled hydromechanical- thermochemical processes. This paper explores the application of the theory of such processes in minerals engineering, with particular reference to rockburst mitigation, in situ solution mining and cavity completion of coal-bed methane production wells.

Jan 1, 1995

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By KeBler H-W, Seeliger A

Vibration analysis for diagnosis of machines is a powerful instrument for condition monitoring. Especially for diagnosis of antifriction bearings various equipment and techniques have been developed and are available. The envelope analysis is the most reliable method for bearing diagnosis. Different bearing failures lead to different patterns of the envelope spectrum. Checking the amplitudes of characteristic bearing frequencies is mostly not sufficient for a reliable diagnosis. Therefore human experts compare the pattern of the spectrum with typical patterns of bearing defects. In this paper a diagnosis system is presented which imitates this action of human experts. Using a neural net the system not only distinguishes typical bearing defects but also detects unbalance, beating of disengaged machine parts and other kinds of machine failures.

Jan 1, 1995

By Whitford DJ

A distinct zonation occurs in the nature of submarine volcanic activity associated with westwards propagation of the Woodlark spreading system into continental crust. Olivine tholeiites (Type I MORB) flooring one spreading segment in the Eastern Sector of the Western Woodlark Basin are accompanied by more evolved "ferrobasalts". Basaltic andesites and Mg-poor andesite-dacites occur on axial and flanking seamounts respectively. In the Western Sector, Mg- and K-rich olivine andesites occur in a rift valley and on an axial seamount near the tip of the propMr/8 tig rift. Observed correlations between 6Sr ratios (0.7028-0.7041), REE patterns and K contents imply a complex petro- genesis with the relative importance of mantle heterogeneity and crustal contamination difficult to resolve.

Jan 1, 1987

By Konishi Y, Morioka Y, Okabe K

A part of the results of dissection survey of Chiba No.1 blast furnace, Kawasaki Steel Corporat- ion, is presented. Distributions of coke size and of slag and metal holdup are shown in the region of the dropping zone. A similar relation to the irri- gated packed bed is obtained. The distribution of coke size, coke temperature and liquid holdup are measured in and around the raceway. The shape of raceway in the horizontal and vertical sections indicates that each raceway worked individually. Liquid flow in the dropping zone and around the raceway on the basis of holdup measurements is Discussed.

Jan 1, 1981

By Burgess J, Brownrigg A

The world steel industry underwent rapid growth from 1950 to 1970. Since that time, production growth has been relatively slow, with declining production in the developed countries and increasing production in some newly developing countries. Since 1970, Western World crude steel production has been static at around 450 million tonnes, with cycles around this level in a 100 million tonnes band.

Jan 1, 1992

By Pathan AG

This research work is concerned with an investigation of the fracture toughness of sandstone, siltstone, and coal. Tensile failure trades have been examined with three different specimen geonetries, i.e; rectangular bar, round bar (in three point bending), and diametral compression discs. The Stress intensity approach, and J-integral methods were used to evaluate fracture toughness. Results from both approaches are discussed. True crack length was determined after pre-cracking, using the compliance calibration technique. Fracture toughness results of sandstone are independent of crack length and the size of the specimen. Fracture toughness may hence be regarded as a material property for sandstone. In cxnntrast fracture toughness values for !siltstone and coal are dependent on crack Length.

Jan 1, 1986

The role of automation in the environmental management of the various stages of mining projects is discussed. Remote sensing can be useful in the exploration phase, but tends not to have sufficient resolution for individual operations. Automatic samplers, whether for meteorology, air or water, are widely used, but can have operational problems. The environmental scientist, the electronics engineer and the computer programmer must combine in the future to develop products which are applicable, robust and simple to use.

Jan 1, 1985

The Western Australian Mineral Sands Industry has tried a number of different mining methods to efficiently exploit the potentially very large reserves of mineral sands in this state.The size of the operation, the location, the type and composition of the orebody contribute towards the choice of current mining techniques.The methods applied to these areas are described as well as reference made to other techniques which will . make possible the exploitation of lower grade reserves.

Jan 1, 1986

By J S. Simmons, J G. Skousen

This project evaluated the performance of nine passive treatment methods by studying 137 treatment units in eight eastern states. Performance was normalised according to construction cost, projected service life and kilograms of acid load treated. Results were dimensioned as $/kg of acid load treated/year. These costs were then compared to those of chemical treatment. Sites that achieved acid load reductions at costs below those of chemical treatment were considered successful. In addition to evaluating the performance of the treatment methods, this paper describes the various passive treatment systems, their applications and performance data for individual treatment units.

Jan 1, 2003

Petroleum exploration and development is vitally important for the future well being of Australia. The Australian petroleum exploration/development industry is alive but not so well. A combination of.:factors point to the industry requiring a much more mature effort in both short and longer-term planning to ensure greater success and effectiveness for petroleum discoveries and development. While many petroleum exploration companies are competently run, there are far too many which will be lucky to survive, even though their exploration areas are highly Prospective.

Jan 1, 1983

Its two years since we have presented at this conference and since that time we have made significant progress with our coal developments in New Zealand. In 2005 we held the Whareatea West exploration permit and had just completed the purchase of the Cascade mine. Today, in addition to Cascade and Whareatea we now have the Takitimu Mine, Eastern Coal Supplies, our coal blending and distribution facility in Timaru, prospecting permits at Ohai and Orepuki and an established customer base underpinned by the contract to supply FonterraÆs Clandeboye plant commencing in September 08. For this presentation I would like to take you through our purchase and development of the Takitimu mine.

Jan 1, 2007

The short review of hydrogeologic conditions in the three Polish coal basins have been presented as the background for the prevention measures against water inrushes being underta- ken in coal mines. The Polish mine safety regulations concerning water inrush prevention have been discussed, namely: - classification of sources of the potential water inrushes, - levels of water inrush risk and conditions of mining operation in the mines facing particular risk levels, - determination of the -di.mens.ons.of protecting pillars to prevent water inrush to mines, protection of surface water reservoirs and their earth embankments in regions submitted to mining deformations. Three examples of coal mining being carried out under water bodies have been presented.

Jan 1, 1988