Search Documents

The preferred alternatives in heap design and their motivation are identified as- -normal heap leaching, to be generally applied wherever possible, - flooded vat leaching, to be appliedwhere wetted ore lacks adequate cohesion or if limited space necessitates it,- thin layer leaching, to be applied where deleterious vat chemistry necessitates it.A number of the following features would probably be incorporated in the optimization of normal local heap leach operations- pre-cyanidation - pre-agglomeration - retaining walls- staged (counter-current) heap treatment- control of calcium levels- reduced pH and trickler irrigation

Jan 1, 1984

By E Mroczek, M Climo, B Carey, M P. Simpson

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The composition and volume of geothermal fluids in New Zealand offers considerable potential for the extraction of various metals and minerals, as well as being a source of heat energy, steam and gases, and for use in generating electricity. While extracting products from geothermal fluids is technically feasible, positive economics is the key driver for commercial success; however, there is no assessment of this opportunity that identifies simple, cost-effective processing technologies and provides a greater understanding of the economic viability and barriers for implementing such technologies. The methodology that will be used to evaluate the commercial opportunities for New Zealand is discussed.CITATION:Mroczek, E, Simpson, M P, Climo, M and Carey, B, 2015. From waste to wealth – mineral extraction from geothermal brines, in Proceedings PACRIM 2015 Congress, pp 133–138 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Vogwill R. I J

The Boddington Gold Mine, operated by Worsley Alumina Pty Ltd, is located about 100 km south of Perth and is one of the largest-producing gold mines in Australia.Multiple open pits are planned and several extend below the water table, through the deeply weathered lateritic profile and into the underlying Archean bedrock. Groundwater related mining problems, such as poor trafficability, wet floor conditions and slope instability began to occur early in 1990.The mine is located within Archean greenstones which are steeply dipping and faulted. Rock types include mafic to felsic volcanics, pyroclastics and sediments. These rocks have been regionally deformed and metamorphosed and are intruded by quartz micro-diorites and post-mineralisation dolerite dykes. Deep weathering has produced a typical oxide profile consisting of laterite, clay and saprolite zones underlain by weathered to fresh bedrock.

Jan 1, 1993

By Peng S. S

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support.

Jan 1, 1992

By Fink ST

Management requires up-to-date information on the activities of an enterprise in order to maintain control and to assist in decision-making and planning. In today's environment it is essential that this information is immediately available and in an easily assimilated format. If this is not the case, management is forced to make decisions based on intuition and past experience. At Mt Newman Mining Co, a computer application has been developed and implemented with the objective of providing this type of information to management. The Key Parameter Reporting System (as the application is known) allows for daily (constant) on-line capture of selected production statistics, safety statistics and free format textual comments relating to topics such as industrial relations, major maintenance and other pertinent news. Information can be retrieved,'and displayed or printed in either a tabular or graphical format. All senior managers have colour visual display units in their offices for immediate access to the system. Access to selected sensitive information is controlled. All company staff are able to retrieve unsecured information from the system via visual display units installed in all company Locations.

Jan 1, 1983

A case-study is presented of the tailings dam of Nairne Pyrites Pty. Ltd., at Brukunga, South Australia. The methods of-construction and operation of the dam are outlined over the whole working life of the mine. Procedures of soil mechanics used to estimate the stability 'of the face of the dam are described, and seepage problems are dis- cussed. It is concluded that the dam is basically stable, and enabled Nairne Pyrites Pty. Ltd. to dispose of tailings economically, although more attention to seepage control may have been ad- vantageous. Suggestions are made on the construction and operation of tailings dams elsewhere.

Jan 1, 1975

The environmental and social responsibilities of the mining industry have long been recognized by the industry itself, but during the past decade it became one of the main targets for the more radical members of the community. This came as something of a shock to an industry which had always considered that it had acted responsibly within the standards of the day. As far back as early 1968, the Australian Min- ing Industry Council (AMIC) was clipping from newspapers the odd letter written by environmen- talists and critics of mining activities. In those days every such letter was carefully studied to ensure that AMIC, if not having the answers, at least had an understanding of the types of argu- ments then starting to be used against mining activity and in favour of environmental preserva- tion. Within 18 months, the infrequent letter to the editor had become a flood of such letters and feature articles, and the environmentalists' attack on mining activities had been launched in all its Vehemence.

Jan 1, 1978

Scheduling the transformation of in situ coal to run of mine coal and its subsequent beneficiation to a saleable product involves the use of many `parameters' or `adjustment factors'. These include in situ density, moisture adjustments, mining

Jan 1, 1998

By Anderson J. M, Gillies A. D S, Jones N

There are a number of current theories in relation to methane migration and emission into workings following underground coal mining activity and some controversies do exist. Mining causes changes in the stress regimes in surrounding strata and results in fracturing. Permeability increases and methane flows into workings under a pressure gradient. The effects of stress on permeability depend on the physical properties of the coal and surrounding strata. Methane emission also depends on the original methane content and the proportion which will be liberated. There are several methods for determining in situ methane content and desorption characteristics of coal samples and several methane prediction methods but clearly more research is necessary to achieve an adequate predictive model.

Jan 1, 1992

By Weber D, Knox PR

The criteria developed for the Argyle Diamond Mine process plant control system are reviewed. The control system installed is described along with a discussion of the method of implementation adopted. The control system was extensively tested prior to instal- lation at site. This approach led to signi- ficant time savings during plant commissioning and facilitated rapid escalation of plant production. The control system has performed satisfactorily with a high level of operator acceptance and basically satisfies the criteria Developed.

Jan 1, 1986

By Rubisov DH

This paper is related to the problems of the mathematical modelling of vibrating screening process and to predicting the screening operation results. The authors propose a model of screening based on the interpretation of granular material segregation on a screen surface as an instantaneous process. Results show an agreement with laboratory and pilot plant tests. Derived formulae can be used for screen sizing and screening result estimating.

Jan 1, 1993

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By Richards AB

This paper describes the ENVIB software system, which has been developed in a menu-driven form to aid in the monitoring and assess- ment of vibration caused by routine blasting operations and for research and development projects. The paper gives an outline of the capabilities of the system by means of screen-dumps and a general descriptive commentary. Technical notes have been added where appropriate to further describe the system. The ENVIB system covers: I . Analysis of blast vibration results, and preparation of graphs and tables for control and estimation purposes. 2. Effects of atmospheric conditions and air vibration propagation. 3. Real-time acquisition and analysis of analogue blast vibration sig- nals directly from transducer equipment or from FM tapes. 4. Analysis of digital files on floppy disc or transferred via the serial port from blast monitoring equipment. 5. Transfer function calculation for structure response studies.

Jan 1, 1988

Samples weighing 0·5 g are fused with sodium hydrogen sulphate, leached with 5 ml. of 4 M nitric acid and diluted to 10 ml. with water. An aliquot of the clear solution is boiled with concentrated nitric acid and then 2 ml. of a phosphotungstate solution are added. After dilution to 10 ml. with water, the solution is heated in a boiling water-bath for not less than 10 min. When cold, the solution is extracted with 2 ml. of iso-amyl alcohol and the yellow phosphotungstovanadate complex is compared with a standard series. Concentrations down to 4 p.p.m. may be analysed at a rate of 100 samples per man-day of 8 hr.

Jan 1, 1971

By P Bartlett, K Naidoo

Premier Diamond Mine is planning a new, mechanised, block cave, with a production level approximately 1000 m below surface. A high degree of tunnel damage is expected, due to stress and the relatively low in situ strength of kimberlite. An evaluation of the timing of tunnel excavation, tunnel size and spacing has been carried out to define critical parameters for planning layouts and development schedules. Extensive use has been made of three-dimensional FLAC3D numerical models, calibrated against known rock mass behaviour at 650 m depth, to examine the influence of undercut advance on production level excavations. These were able to represent the effect of stress rotation on tunnels during undercut advance and the effect of an inclined undercut. The analysis has provided guidelines that are possibly applicable to any deep block cave layout. The choice of drawpoint layout is of considerably less significance than the proportion of ground extracted on the production level elevation prior to advancing the undercut. The analysis shows that damage to production development will be potentially severe if it is all excavated prior to advancing the undercut, or is mined directly beneath the undercut face. The development of the main production tunnels alone ahead of the undercut may be feasible, but no breakaways should be put in as they appear to trigger a rapid increase in the severity of damage. The optimal sequence is when all production tunnels are developed at least 10 m in plan behind the undercut, where the induced peak field stress is less than 20 MPa and a maximum support pressure of 100 to 500 kN/m2 is require to contain movement. The assessment showed that the conditions are not significantly improved by increasing drawpoint spacing from 15 m to 18 m. The vertical spacing between the undercut and production level beneath is investigated. Provided production level development is carried out beneath the undercut, there would appear to be little benefit in increasing the vertical spacing between the undercut and production level beyond the current 15 m to 18 m.

Jan 1, 2000

By d&apos, Alton AJ, Rigden DT

Modern petroleum refining offers a complexity of environments, each requiring different metals for the satisfactory performance of-the various sections of the refinery, and this paper first outlines the varied enva.x¦on-ments thus met.It follows that the metal types in use will also vary to suit each particular environment, and the paper' consequently covers the use of ferrous-metals, ranging from plan carbon steels to the high alloy types and the non-ferrous metals, particularly copper and its alloys.The failures of some,of these metals and alloys are then illustrated by experiences it Kwinana. These failures are duo to (a) corrosion, (b) erosion, (c) faulty welding, and (d) mechanical defects,' of which the first is by far the most prevalent. The protective measures taken to prevent subsequent failures are then given under one or other of the following headings :(1) alterations in process conditions, (2) the use of alternative ,alloys,(3) suitable heat treatment, (4) redesign of the failed section, (5) cathodic protection, and (6) use of corrosion inhibitors.Reference is then made to the use of specialised metals and alloys.Metals, generally in the form of oxides or salts, are also used as catalysts in refining processes. Activated alumina is used, combined with silica .forScracking' of heavy oils, and as a support -for platinum, cobalt, molybdenum, nickel and similar metals, which catalyse hydro-genation and dehydrogenation-processes. .In the final formulation of petroleum products metallic compounds may be added. Reference is made to the large quantities of lead used by the petroleum industry and to the use of metallic soaps and detergents in the formulation of lubricating oils and greases.

Jan 1, 1962

Modern plate tectonic reconstruction of Mexico and Central America shows that the southeast-extend ing Precambrian backbone of Mexico, together with the east-flanking accreeted Huastecan (Appalachian-Caledonian) orogenic belt, are geotectonic elements practically absent in Central America, except west-ern and northern Guatemala and Belize, and contrib-uted little to the mineral potential of the entire region.The gradual accretion of the Cordilleran oro-genic belt took place against the western-south-western margin of the Precambrian backbone, and its consolidation required several tectonic events from the medial(?) Paleozoic to the end of the Mesozoic. The striking features of this "long-lived" orogenic belt are the massive sulphide min-eralization in the upper Paleozoic eugeoclinal as-semblage, the widespread gold occurrence in quartz veins in the lower Mesozoic volcanics and related intrusives, the carbonate-hosted silver-bearing lead-zince deposits of the Mississippi Valley-type (or Pine Point-type) around carbonate banks within the Lower Cretaceous back-arc miogeocline, that de-veloped over the Precambrian backbone and deeply-eroded Huastecan orogenic belt, the massive sul-phide (Pb-Zn) deposits in the Upper Jurassic-Lower Cretaceous sequence, transitional from miogeocline to eugeocline, which carry high grades in silver, and the iron deposits in this transitional facies, which are described in the literature as related to dioritic intrusives of Late Cretaceous age. Central America, south and southeast of the Mota-gua-Polochic fault system, forms part of the in-ternal zones of this orogenic belt.

Jan 1, 1990

Based on twenty years of experiences of applying computers in mine water engineering in Hungary, a program package was developed for home utilization and for other users abroad as well. This program package has been adapted to the CAD System of Coal Mining of COMECON countries. The main features of the "mine water subsystem" in the CAD System of Coal Mining and short descriptions of the key programs of the package are presented in this paper. Foreword The serious water problems of Hungarian mining pressed and/or stimulated its professionals to apply computers for supporting their problem-solutions. The first trials of these computer applications in mine water engineering were dated from the sixties. Owing to its twenty years of experiences in computer appli- cations in mine water engineering the Central Institute for the Development of Mining in Hungary was requested to work out the "Subsystem of Mine Water" for the Computer Aided Design System ('CAD) of Coal Mines in COMECON countries. This paper gives a brief presentation on the main features of this "subsystem"with reference to significant components.

Jan 1, 1988

By Northcote GG

There are many underground mines with shaft or decline access with limited production capacity or where the mine may become uneconomical as trucking costs escalate with increasing depth of the decline. In such cases a need may exist for a shaft hoisting system which can be constructed more quickly and more economically than a shaft sunk by conventional methods. Relatively cheap small diameter shafts can be constructed by raise boring. This paper describes a simple hoisting system which has been designed to take advantage of the benefits of raise boring. The system uses twin bored raises with a double drum winder hoisting a skip in each hole. The design concept is based on 1. accepting that the raises cannot be truly straight or vertical, 2. using the raise to guide the conveyance, and 3. minimising operating, maintenance, and capital costs. The hoisting system requires a certain degree of accuracy in the alignment of the twin raises. A survey of raise boring practice showed that the required accuracy could probably be achieved with conventional techniques. However it was thought it would be necessary to survey the pilot hole during drilling and to be able to correct the hole if deviation became

Jan 1, 1978

Flue gases from electrical power station boilers, roasting, metallurgical and chemical plants could be treated by flotation using conventional flotation machines. The flue gases are introduced into the pulp instead of the air. The flotation media is a suspension of Ca(OH)2 or CaCO3 or a solution of NH4OH etc containing Na oleate as collector and frother. The SO2 and dust content of the initial flue gases were experimentally reduced by 100 to 1000 times in one flotation operation. The velocity of the flue gases through flotation machines could reach approximatively 0.4 to 0.5 m/s and more against 1.5 m/s reached in scrubber absorbers used for this purpose, but the quality of purification is expected to be better for flotation, which is essential for the cases of heavy polluted metallurgical and chemical flue gases. For some chemical plants the flue gases flotation media may be different and more suitable as compared to the above mentioned media. The proposed flotation method could be used for separation of dry grinded ores in the form of aerosols, with a realisation of flotation from a closed space (gas bubble in the pulp) onto the interface liquid-air where the particles are attached inside the bubbles.

Jan 1, 1993