Search Documents

By Wright D. J

Successful heap leaching depends on three major factors: 1. Chemical conditions appropriate for the dissolution of the valuable metal; 2. Contact between the leach solution and the valuable metal particles; and 3. Movement of the leach solution through, and out of, the heap. Given that appropriate chemical conditions can be provided, and the individual particles have sufficient permeability to allow solute/solvent contact, the problem of getting the solution to and from the particles remains. Non-uniform percolation of solution throughout the heap, caused by the presence of fines, is a common problem which occurs, to some extent, with all heap leachable ore. The conventional solution to this problem is agglomeration, which involves the attachment of fine particles to larger particles, effectively modifying the size distribution by preventing the fine particles from acting on their own. While agglomeration must be considered as an extremely effective technique with virtually no limit to its application from a technical point of view, its application is limited by economic considerations. A new technique has been developed which is not only a low cost alternative to agglomeration, but also has the potential for enabling the application of low cost heap and vat leach techniques to a significantly wider range of ores than current practice would suggest. The new technique, known as Electrokinetic Leaching, utilises electro-osmotic flow to enhance percolation through the heap. This paper describes and presents results of the laboratory testing, pilot heap operation and commercial application of Electrokinetic Leaching of a low grade gold ore and a tailings deposit. Comparative cost analyses between conventional and the alternative processing techniques are presented.

Jan 1, 1994

By Blair JR

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

By Boyle L. A

A positive displacement pump is being dev eloped for pipeline transportation of coking coal to a -50 mm export specification, at a con- centration and velocity which will allow trans- portation in the plug flow region, minimising degradation of the particle structure, and pipe= line friction losses which will be lower than with turbulent or laminar flow. Pump operation is by hydraulic powered free pistons in a rota- ting cylinder block, with cylinders overlapped by stationary inlet and discharge ports in a water lubricated and sealed rotary valve. Before this development coking coal was not considered suitable for transportation in slurry form, for the valves in the double act- ing duplex piston pumps used for slurry pipe- lines, cannot be divorced from the slurry and require that the solid material must be reduced to a fines'consistency before introduction into the pump suction. The hydraulic transportation of 10 million tonnes of -50 mm coking coal, 50 km from the Bargo area west of the escarpment to an offshore shiploader at Port Kembla is feasible. Study shows that economic factors alone would dictate that the development of a pumping system for long distance transportation of coking coal is necessary. The greatest impact from the slurry transportation of coking coal would be the

Jan 1, 1976

One of primary causes of poor blast performance is the improper relief of explosive energy. Under or over-confined blasts modify the explosiveÆs path of least resistance, which changes where and when the explosive energy is applied resulting in less than optimum blast performance. During the research for this paper the overbreak characteristics of five full-scale blasts were quantified using high speed cinematography and borehole cameras. The effectiveness of various overbreak control methods was also evaluated to guide design refinement. The results of this research along with general recommendations for reducing excessive damage are included with this paper.

Jan 1, 1999

Optimisation of capital in the development process is critical to the profitability of any new mining venture. The process of optimisation should apply to all aspects, that is the financing, management, revenue, reporting and, of course, the development of the project. Unfortunately, too much emphasis has been placed on the optimisation of the financing or reporting aspects and too little on the project itself. This paper addresses the latter.

Jan 1, 1991

By Chugh Y. P

A simplified, three-dimensional, time-dependent, mechanistic model of the overburden-coal seam-floor interaction has been developed and validated at two Illinois coal mines. The model based on the thin plate theory can involve any complex layout of mine workings, time-dependent sequence of extraction and, rheological properties of immediate floor strata. The model output data consist of spatially distributed surface subsidence and its slope and curvature, as well as load acting on pillars in one or more panels. A comparison of calculated and monitored surface subsidence or in- mine convergence measurements has proven the model's effectiveness for surface subsidence and load transfer Prediction.

Jan 1, 1992

Paddington processing plant is located approximately 30 km north of Kalgoorlie on the Menzies Highway and is owned by Placer Dome Asia Pacific. First mining was from the Paddington Pit, but in subsequent years the plant has had a history of treating ores from a large number of sources, and has used several different methods to reconcile mining and mill production. Reconciliations are necessary to keep a check on the quality control of mining and grade control processÆs. There is a need to be able to identify and resolve issues that will affect the profitability of the organisation quickly. They are also used to check the quality of the resource/reserve statements, and allow the accurate and timely payment of royalties to stakeholders. During the formation of the Kalgoorlie West operations when Delta Gold Limited and Goldfields Limited merged in 2001, the complexity of reconciliations increased dramatically. The expansion of the scope of reconciliations to include two mills, four underground mines and seven open pits, and ore from one deposit to both mills meant that a revised strategy was essential. A variety of issues have arisen over the years with discrepancies occurring when reconciling both tonnes and grade. There are many ways to approach reconciliations, and in recent times these philosophies have been widely debated on site. A consistent and logical approach that takes into account many different sources of ore, as well as different methods of delivery to the Run of Mine stockpiles is therefore necessary. This would standardise the different approaches taken by the various operations that combined to form Kalgoorlie west. The new method reconciles mill production back to the individual ore sources, and produces reconciled-mined tonnes and grade based on the mill throughput and the change in stockpiles. There will generally be a small discrepancy between the claimed mined tonnes produced (and grades) and the mill production. This needs to be highlighted to the operations concerned if it considered unacceptably large. Paddington mill over the last few years has had up to ten sources of ore each year, and up to 15 different stockpiles being processed during each month from those various pits. This combined with the need for a blended oxide/fresh feed, whilst striving to deliver a consistent (grade and hardness) product to the mill, has meant that reconciliations have been very difficult.

Jan 1, 2003

During 1991 - 1993 the author interviewed approximately thirty senior managers of varying responsibilities in either the engineering, construction or operation of a heavy industrial facility. The purpose of the exercise was to determine the factors driving a deterioration of the working relationship between the engineering and the operating company following practical completion of a major project. From the research a number of conclusions have been drawn as to the root cause of the deteriorating relationship. For this paper we are drawing on this initial research and our ongoing experience of solving problems of this nature to present some fundamentals that can be used to break the breakdown maintenance cycle.

Jan 1, 1998

By Leahy GJ, Wright DJ, Player RI

The operation of a one tonne submerged combustion pilot plant for the recovery of copper from anode furnace and converter slags is described and the effects of variables discussed. Using coal as reductant, copper levels of anode furnace slag were lowered to 1% or less, with batch times of approximately 120 minutes. Fluxing with limestone was required to produce a fluid slag at temperatures of 1200 - 1300¦C. For converter slags, reduction to 0.5% Cu or less was achieved in batch times of 35 minutes. The chemistry of the pyrometallurg- ical recovery of copper is briefly reviewed in relation.to copper recovery methods.

Jan 1, 1978

By Owen D

A central part of mine planning is to ensure the protection of the beneficial uses of water. Integrated mining software does not generally provide tools to help the mining engineer to achieve this objective. This paper identifies some of the requirements which are desirable for such a tool and discusses how object oriented modelling can help achieve an effective design.

Jan 1, 1995

By Y Gu, W McCallum

Mathematically sophisticated methods are now in common use for metal balancing of complex separation flow sheets at many concentrators. These balances usually entail minimisation of the sum of weighted squares of data adjustments subject to flow sheet constraints. The adjusted data provides numerical consistency across the complete flow sheet to facilitate performance calculations. A mine with multiple ore sources can be considered as a flow sheet with the end node comprising the concentrator and its products concentrate(s) and tailings. If the mass transfer and grade estimates for each ore source are sufficiently reliable, a similar metal balancing approach can be used for combined mine and concentrator data. Comparison of balanced and measured assays and mass movements provides useful guidance to security of marginal grade ore and possible dilution problems. This paper includes a summary of results from a case study based on a mine with multiple ore sources.

Jan 1, 2002

Productivity of mines can be improved by taking fewer, but larger blasts. The initial blasts taken in starting a mining block are restricted by the low amount of void or space to fire into. Block cave mines are using a blasting technique to blast areas that have less than the normally accepted minimum void to establish drawbells for their orebody development. This technique used in block caving mines can be used to improve productivity in mining operations that utilise other mining methods. Some larger blasts have been done in mines, using open stoping methods, which have had void ratios as low as 13 per cent. This has been possible with the use of the explosive gases to transport the broken rock out of the area normally considered to be available to blasts. This trapping of the explosive gases in the broken rock has allowed rock to be moved over 30 m, horizontally, to allow for more void to be available in the blast area. This gives the necessary void ratio allowable to fire larger blasts. This paper will discuss the blasts where this technique has been used in mines to increase the tonnes fired in low void situations. It will also discuss where this type of blasting may improve the productivity of underground mines. Figure 1 shows the how explosive gases have enabled the broken rock to flow out of a draw point without the typical air blast and fly rock that would normally cause a rope suspended sign to be damaged beyond use.

Jan 1, 2008

By B R. Olsson, N Marinopoulos

To establish the design and the capacity of the Stanwell Magnesium Plant, Australian Magnesium Corporation Ltd (AMC) with Fluor Australia has modelled the operation of the magnesium plant using ARENA Simulation Modelling. The reliability model has been used to evaluate: surge capacities required between different sections of the plant; critical equipment requiring standby capacity; the number of trains required for different sections of the plant; and potential capital cost reduction options. The reliability model was established using the detailed Process Flow Diagrams, reliability information from literature and maintenance, operation and start-up experience from the Demonstration Plant. The model was run with different plant configurations to assist AMC in determining the most effective configuration to provide the production capacity at the lowest capital cost. The model was not only able to confirm the plant capacity to the independent technical expert but was able to minimise quantitative risk by minimising the quantities of hazardous materials on site. Fluor Australia provided the ARENA simulation expertise and has used this software for optimising new plant design and to establish improvements in operating plants. Reliability modelling is a normal feature of chemical plant design but is rarely used in the resource industry. The experience gained by AMC in the modelling system has indicated that metallurgical plant design can be improved by the application of reliability modelling.

Jan 1, 2002

Material hardness and environmental factors can limit or restrict conventional blasting techniques and this has led to advancements in the performance and efficiency of ripping. Not all materials can be ripped, however today's technology and experience can help make a reasonable prediction. A ripping versus blasting decision will depend on the total volume of material to be moved, the production capabilities and costs of the ripping tractor(s) and on the size and relative efficiency of drilling and Blasting.

Jan 1, 1995

By S La Brooy, C Fountain

Throughout its history the mining industry has focused on the highest-grade deposits sited in the most convenient locations. The burgeoning global population and higher standards of living not only increase the demand for mineral products but also make it harder to mine and process them. The future will include the development of lower-grade, more complex orebodies, and orebodies in difficult locations. The industry will be expected to provide for humanityÆs needs while reducing its environmental footprint and maintaining profitability. This paper reviews some of the likely adaptations in mineral processing that will occur over the next 20 years. The challenges inherent in adapting to lower grade and more complex materials might be exacerbated by such factors as the availability of water and low-cost energy. In underground mining, higher energy costs are likely to foster further developments in underground preconcentration, especially for ores that can be upgraded at relatively coarse sizes. The adoption of underground crushing could also render material amenable to semi-dry preconcentration options such as might be achieved by the rotary classifier developed by CSIRO and being commercialised by RCR Tomlinson, or more modern versions of the hand-sorting of ore that use sensors based on colour or other suitable rock properties. The cement industry and some gold roasters have used the alternative of dry grinding and classification, which might also have a part to play in dry processing. There is also likely to be increased interest in options such as in situ leaching that further minimise the surface disturbance. Underground operations will have to balance the energy savings from reducing the amount of material brought to the surface and reduced surface disturbance against the practical limitations of installing and maintaining processing equipment underground. On the other hand, surface disturbance and energy issues in open cut operations will be balanced by potentially lower mining costs and higher overall recovery from the deposit.

Jan 1, 2008

In engineering applications of explosives for rock breaking, the released energy is expended mainly into heat, rock crushing and fracturing, seismic waves, air blast, and noise. Those parts of energy which pass into seismic waves and air wave create environmental problems since they are transmitted away from the blast site. In order to predict the environmental effects accurately, one must be able to predict the energy distribution at the source. The energy distribution at the source is significantly controlled by the blast constriction. Consequently, the accuracy of prediction and control of ground vibrations generated by blasting is affected by various matrices of blasting constriction.

Jan 1, 1986

By Boyack DJ

DEFINING AN ECONOMIC TARGETExploration usually begins with the corporate goal of finding a minimum tonnage and grade of a selected mineral. Sometimes this is expressed more simply as a minimum quantity of contained metal without any indication of the desired grade or implied profitability. Such a goal is useful in the selection of exploration areas and the planning of initial drilling programs. However, it should be reviewed as soon as significant mineralisation has been identified. To make rational decisions about exploration expenditure, the potential return from a deposit must be estimated from the outset and re-esti-mated frequently.The potential return will depend on:1. The proportion of mineral which can be economically recovered from the deposit by mining (the mining recovery).2. The quantity of valuable constituent that can be recovered after dilution with waste rock during mining and losses due to incomplete metallurgical recovery.3. Expectations of price and markets.4. Capital and operating costs applying to the selected mining and processing methods, and to transportation and marketing. Increasingly, environmental costs and constraints must also be considered.

Jan 1, 1990

By R Simonato

It is now recognised that rotary sample division is by far the best laboratory tool for extracting subsamples from a lot of material. In terms of sampling theory, rotary division, by virtue of the fact that it can extract many increments from the lot during the division process, radically reduces the variance due to distributional heterogeneity in the sample being divided. There are a number of occasions in sample preparation when it is necessary to extract a subsample of a target mass. To do this with rotary dividers taking a fixed fraction of the starting mass is a tedious task. In response to this problem, a variable split sample divider has been designed and built for the mineral industry. This paper discusses the utility of the device and presents test data showing that the machine is capable of making accurate mass split while overcoming segregation in the material being divided.

Jan 1, 2008

By Fourney W. L, Weaver T. A

A large number of single borehole crater-forming shots were analyzed in terms of correlating the crater parameters with explosive weight. The objective was to determine a scaling rule for which the explosive weights varies over many orders of magnitude and covers many different geologic materials. Included in the data base are type and weight of the explosive, geologic medium and degree of saturation, charge depth-of-burial, crater dimensions, and crater rim (lip) measurements. An alternative scheme to the usual plot of scaled depth-of-burial versus scaled volume removed was desired. The proposed technique uses a plot of the logarithm of the explosive weight, Y, versus the logarithm of the slant length, R', calculated from the known depth-of-burial of the explosive and the measured crater radius. A plot of Log Y in kilotons versus Log R' in meters from all the crater tests in this data base resulted in a straight line with a of slope 0.31 and showed good correlation between the variables Log Y and Log R'. Since the crater data includes many geologic materials, different explosives (including nuclear tests), and large differences in charge weight, the straight line fit suggests that the type and strength of the geologic materials play a subordinate role to explosive energy in crater formation.\

Jan 1, 1990

Attention is given to three possible alternative structures namely corporate joint venture, partnership joint venture and unincorporated joint venture. A corporate joint venture involves the formation of a separate and distinct legal entity with limited liability. The shareholders of the Company will be the members of the consortium. A partnership joint venture involves the members of the consortium joining a formal partnership. The partners will conduct the business in common with each other and will share the profits and losses of the project activities. The partners will be jointly and severally liable. An unincorporated joint venture is distinct from a partnership. The members of the venture will not be jointly and severally liable. Taxation and accounting aspects are examined and an outline provided of a typical joint venture agreement. The two main advantages of an unincorporated joint venture are considered to be a favourable treatment for income tax purposes and a greater degree of flexibility when compared with the corporate joint venture and the partnership joint venture.

Jan 1, 1983