Search Documents

By D. H. Wertz, R. R. Furlong

Dry room equipment at Donora Zinc Works is of the design which prevailed at the time the plant was built in 1915. It consists of 11 adjoining rooms, each being 99 ft long, 11 ft wide, and 7 ft high and having a capacity for 1040 retorts. Heat is supplied by steam coils beneath the slatted wood floor and by warm air ducts at the ceiling. Drying practice is about the same as that generally followed in the industry except that, under normal zinc furnace operations, the maximum drying time is 45 days. During certain seasons of the year the drying process was seriously affected by varying weather conditions which frequently resulted in a scrap loss of 5 to 7 pct. Because of these unfavorable conditions, which caused uneven drying and strains in the retorts, increased retort failures in the zinc furnaces were recorded. Regulation of temperature and humidity under all conditions appeared to be the logical solution of this problem. Controlled drying had been developed for a number of ceramic products and investigation of several such drying processes in this area revealed favorable results. Along with control of drying conditions and the attendant decrease in scrap losses, plant operators also reported a material reduction in drying time. Another factor affecting the decision to proceed with this development was the drastic change in market conditions for retort clay. Curtailment of shipments from the chief source of supply made it necessary to proceed with blending of other available clays, but quality of these clays was questionable for adequate retort life in the 24 hr furnace cycle. Rapid furnace testing of new mixtures was desirable but impossible with the prolonged drying schedule. Therefore development of a controlled drying process for zinc re- torts offered the solution to the problem of rapid testing of retort mixtures. Description of Process and Equipment The freshly extruded retort is cylindrical in shape, 58 in. long, 9 in. id and has 1 1/8 in. side walls. One end is closed and approximately 2 in. thick. The moisture content of this "green" retort is about 17 pct which means a necessary removal of 30 lb of water per retort. Retorts are set on the slatted floor of the dry room with the closed end down. The controlled drying process depends upon the circulation of a large volume of conditioned air at low velocity. To provide for uniform distribu-

Jan 1, 1950

By Kalervo Rankama

UNTIL a few years ago, geological mapping, the study of ore boulders, and different geophysical methods were the principal means used in the systematic search for mineral deposits covered by a layer of disintegration products or soil. These methods have been developed to a high stage of perfection as far as the geometrical definition of the conductor is considered. Use of geophysical methods in prospecting is based on the fact that an ore body differs from the country rock not only geologically but also in its physical properties. The general drawbacks and complications included in the use of geophysical methods are well known to everyone who has been using them, so need not be entered into here in detail. One of the more important ones is the fact that geophysical methods are unable to furnish information concerning the chemical composition of the ore bodies responsible for the indications. Further, the ores of many metals, such as silver, gold, beryllium, zinc, mercury, tin, lead, vanadium, antimony, chromium. molybdenum, tungsten, manganese, cobalt, nickel, and the platinum metals cannot be directly located by known geophysical methods, owing to lack of physical characteristics suitable for distinguishing them from the country rock. Thus it is quite natural that efforts have been made to develop direct methods for prospecting and locating ore bodies of the elements named. Known as chemical, biogeo-chemical, and geobotanical methods of prospecting, these have been much improved during recent years. A brief review of these methods and of some results obtained with them will be presented in the following, on the basis of available information and my own experience.

Jan 1, 1947

By J. S. Koehler, F. Seitz

THE dislocation theory of plastic flow originated in 1928, when Prandtl1 suggested that the internal damping of metals of plastic origin might arise from the motion of a crystalline imperfection. Following this, Dehlinger2 employed a similar imperfection in a theory of recrystallization. The first detailed theoretical discussions were those of E. Orowan3 and G. I. Taylor4 in 1934. The resulting theory was gen- eralized by J. M. Burgers5 in 1939. Mott and Nabarro, in England, and Seitz and Read,6 in the United States, started an extensive examination of the atomic theory of dislocations in the period between 1939 and 1941. However, this development was arrested by the mar and was not taken up again until after 1945. Since 1946, the field has been the object of very intense activity, particularly in the United States and England. Dislocations are beautiful and intricate imperfections; they are sufficiently complicated to account for the great variety of phenomena encountered in the field of plastic flow. Above all, the dislocation concept enables us to understand how a metal or other plastic solid can deform inelastically under very small stresses at temperatures far below the melting point. Suppose we attempt to shear a perfect crystal plastically. This can be done by sliding one entire atomic plane simultaneously through one atomic distance with' respect to the near-

Jan 1, 1954

The Motor Truck Sections of the 20th Annual Automobile Shows of 1920, to be held in the 8th Coast Artillery Armory, New York, Jan. 3 to 10, 1920, and in the International Amphitheatre, Chicago, Jan. 24 to 31, 1920, will he the largest and most comprehensive exhibitions of the kind ever held. Approximately 125,000 sq. ft. of exhibition space has been alloted at each place and upward of seventy makes of motor trucks, together with trailers, pacts and accessories will be dis-played. In conjunction with these expositions, Highway Transport Conferences will be held, with sessions each afternoon and evening. Every important phase of highway transportation will be discussed by men recognized as qualified authorities. Various talks will he il-lustrated by motion pictures and stereoptican slides. Members of the Institute may apply for complimentary tickets to-S. A. Miles, Manager, 7 East 42d Street, New York City.

Jan 12, 1919

By L. Leibowitz, M. G. Chasanov, L. W. Mishler

A drop calorimeter system is described for use in measuring enthalpies to 3600°K. Data are presented for tungsten between 2800" and 3600°K. The enthalpy of tungsten in cal per mole between 2000° and 3600°K can be represented by the equation HºT- Hº298 = - 1.7622 X 103 + 5.7772T + 8.9861 where T is in degrees Kelvin. A tabulation of com -puted values is presented for heat capacity, entropy, and free energy function. A drop calorimeter has been constructed to carry out enthalpy measurements at temperatures to 3600°K. Samples are heated by induction1 and dropped into a commercial adiabatic calorimeter, modified for this purpose. The experimental temperature is limited by the melting point of container materials and compatibility of the container and its contents. Several high-temperature drop calorimeters have been described in the literature1-5 but none has been used at temperatures as high as those in the present work; our measurements of the enthalpy of tungsten range from 2800" to 3600°K. DESCRIPTION OF EQUIPMENT An overall schematic view of the equipment is shown in Fig. 1. Power for the induction coil is supplied by a 25-kw 250 kHz Ther-Monic generator coupled to an iron core RF transformer. The Sample capsule is suspended in the work coil by 10-mil diam tungsten wires which are wrapped around a horizontal 5-mil diam tungsten wire. The horizontal suspension wire is clamped between two massive copper electrodes which are fixed in an x-y motion device that allows adjustment of the position of the heated capsule from outside the vacuum chamber. The copper electrodes are connected by flexible copper straps to a 1250-joule (5 kv, 100 pfarad) condenser bank. When it is desired to release the capsule, the condensers are discharged through the horizontal suspension wire causing it to vaporize rapidly. Very reliable and precise release of the capsule is achieved in this manner. Experiments have shown that no heat correction is required for this discharge energy. As part of the temperature measuring system, two prism holders have been incorporated in the apparatus. The upper prism holder is in the main vacuum chamber itself, whereas the lower one is in a side arm attached to the drop tube below the gate valve. The upper prism is mounted on a rotary vacuum feed-through, and may be moved under a protective shield when not in use. This prevents deposition of vapors on the prism surfaces when temperature measurements are not being made. Similarly, the lower prism is mounted on a push-pull vacuum feed-through, and when not in use may be pulled into its side tube. The prism mountings are fitted with guides and stops so that they may be moved precisely into the desired position. The aim throughout is to minimize the time the prisms are exposed to vapors from the hot samples. At the high temperatures reported in this paper, only the lower prism was used. The upper prism holder in these cases was fitted with an additional radiation shield. By using a prism and viewport, the lower surface of the samples can be observed by an optical pyrometer. The measurements discussed in this paper were obtained with a Leeds and Northrup 8622-C-S series manual pyrometer which is estimated to be accurate to 0.5 pct. Pyrometer calibrations and prism and window corrections were carried out in the conventional manner6 using tungsten strip lamps calibrated by the National Physical Laboratory, Teddington, England. Prism corrections were rechecked after each use. All work to date has been done in vacuum, and no measurable change has been observed in the prism correction below -2300°K for the upper prism and below -2800°K for the lower one. The total time of exposure of the prisms is about 50 sec per run. At high temperature, the final temperature reading is corrected by using the final A value for the prism; see Ref. 6 for details of this procedure. The calorimeter is a modified Parr Instrument Co. (Moline, lll.), Series 1230 adiabatic calorimeter with automatic jacket control. Other authors5 have used a similar calorimeter with good results. The calorimeter jacket cover and calorimeter cover are attached to the drop tube which contains a radiation shield. This shield is a gold-plated copper disc which can be operated manually from outside the calorimeter. The receiver is attached below the radiation shield and is lined with tungsten. In a typical experiment, the calorimeter and its jacket water temperatures were adjusted to 0.000°K temperature difference. The sample was allowed to equilibrate in the furnace at the desired temperature for about 20 min. The initial calorimeter temperature was then recorded, the sample dropped, and appropriate shutters closed. After about 3 min, the drop tube and receiver were filled with helium to 60 torr. The final calorimeter temperature was recorded after it had remained constant over a 5-min period. The equilibration time in the calorimeter was about 25 min. Thermistor probes are used to operate a hot and cold water supply system to maintain the jacket temperature equal to the calorimeter temperature. For actual measurements of the calorimeter temperatures, a quartz thermometer was used (Hewlett Packard Dymec Thermometer, Model #2801A). This thermome-

Jan 1, 1970

By W. E. Gaby

THE form of dip chart here presented for the use of the profession was devised by the author when he was confronted with a particularly heavy job of geological section making and. did not have any of the usual tables or charts at hand. This was at the property of the Teziutlan Copper Co. in Puebla, Mexico, where the orebodies are much faulted and lie conformably with a slightly inclined and. much folded schist. Because of the low dip and the folding of the orebodies, the engineering, and geological data respecting them were best represented on vertical cross-sections quite closely spaced. A less finished form of the chart was published in the Mining & Scientific Press of Aug. 6, 1921, with an explanation of its use. I have checked the new drawing for accuracy against the calculated table given, and constructed an explanatory diagram beneath. As some geologists are accustomed to using the table, I have included it, since no advantage is obtained by mere interpolations from the chart to get the required angle, except as it gives a mental picture of this angle. The chart gives a more rapid and much easier solution when cases multiply so that it becomes desirable to eliminate the tedious manipulations of a separate protractor. In fact, using the parallel ruler as des-cribed, it is not even necessary to make note of the angle sought. It is brought out graphically, leaving the mind free to note the correlations. The chart itself may be made more convenient by reproduction on celluloid with a slot running on the zero line of the protractor.

Jan 9, 1922

General Aurelio Blanquet,* the best known of living Mexican soldiers, formerly the trusted friend of Porfirio Diaz and organizer of the old Federal Guard of Mexico City, who as a sergeant commanded the squad that executed sentence on Emperor Maximilian, and. more recently was Minister of War in the Cabinet of Victoriano Huerta, landed in Mexico early in April and joined the forces of Felix Diaz. His landing in the state of Vera Cruz, it was stated, was for the definite purpose of aiding the movement now under way to overthrow Venustiano Carranza and to place in power a government that will be "pro-Ally" in its sympathies and will promulgate and enforce laws that will guarantee the rights of life and property in Mexico. The New York Tinges says of the revolution editorially: "Whatever may be the success of General Aurelio Blanquet's attempt to overthrow the Carranza Government in Mexico, admiration cannot be withheld from the General's publicity manager. No enterprise awning at the overthrow of a Government ever had more favorable and widespread advertising. Felix Diaz, whom Blanquet is going to reinforce, supersede, or overthrow, as the case may be-Mexican precedent in these matters offers opportunity for considerable speculation-has been conducting his revolution, at the old stand for some time, but without much success. But, says General Blanquet's representative, the landing of Blanquet will send a thrill to the heart of every true republican.' Meanwhile a biographical booklet is published, adorned with photo¬graphs illustrating the General's record, including such varied matters as the General in favor, receiving a decoration from Victoriano Huerta, and the General in exile, feeding the birds in Central Park."

Jan 5, 1919

By AIME AIME

THE 129th meeting of the American Institute of Mining and Metallurgical Engineers convened at New York City, in the Engineering Societies Building, Feb. 18-20, 1924. On February 21 an excursion was made to the Bethlehem Steel Co., at Bethlehem, where about 200 members and guests were splendidly entertained. An illustrated description of the Bethlehem Plant will be published next month. The meeting and excursion were largely attended; the registration at New York totalled 1276 versus 1201 in 1923. William Kelly, long identified with the iron-mining industry of the Lake Superior district, was elected President of the A. I. M. E. for the coming year, at ,the annual business meeting, Feb. 19, succeeding E. P. Mathewson. The following Directors were also elected (the date signifies year of termination of office; the final figure indicates the "District" the Director represents).

Jan 1, 1924

By James E. Little

(Wilkes-Barre Meeting, June, 1911.) OF the several extensive deposits of brown iron-ore in Cuba, including those of Mayari and Moa, that of Mayari was the first to be systematically explored, and was selected as the scene of the first operations in the development of this class of ore. Construction-work, begun in the spring of 1907, involved the building of 16 miles of standard-gauge railroad and two large double-track inclines, the installation of mining-machinery, a nodulizing-plant, power-plant, shops and shipping-facilities, and the dredging of an extensive basin for deep-draught vessels. Unusual weather-conditions delayed the completion of portions of this work so that the entire plant was not in operation until December, 1909. The ore in its natural state contains a very large percentage of water, which increases to some extent with the depth below the surface. Near the surface it is red in color, with somewhat granular structure. The color gradually changes with depth, finally reaching a bright yellow. The consistency also changes towards, the bottom to a clay-like, sticky mass. The relative proportion of red and yellow ore is quite variable; in some places the yellow reaches close to the surface, while in others the red extends almost to the underlying serpentine. Fig. 1 is a map showing the Mayari division of the Spanish-American Iron Co. The ore lies on an irregular plateau about 15 miles long and 5 miles wide at the widest point, entirely covered with pine trees and brush, which grow directly on the ore. The elevation at the northern extremity, which is approached by the railroad, is about 1,700 ft. above sea-level. At the southern end the general elevation is about 2,000 ft. Ore is removed by means of scraper-bucket excavators and steam-shovels, these machines loading into special standard-guage, side-dump steel cars of 100,000 lb. capacity. A short haul

Aug 1, 1911

By A. S. Yue, A. E. Vidoz, F. W. Crossman

Tensile specimens were prepared from a single grain of an epitaxially grown Al-CuAl2 eutectic ingot. The eutectic lanzellae were oriented parallel and perpendicular to the tensile axis of the specimens. Since the composite was of the eutectic composition, the aluminum-rich matrix could dissolve up lo 5. 7 wt pct Cu in solid solution and, therefore, was amenable to strengthening by precipitation hardening. The tensile properties of the eutectic single crystals were determined at room temperature as functions of interlamel-lar spacing, platelet orientation, and thermornechanical trealment. The obserced variations in composite stress and modulus with respect to the level of&apos; composite strain are discussed in terms of premature fracture of CuAlz platelets, a distribution function for the strength of the lamellae, and unequal strains due to localized fracture of&apos; platelets. The discontinuous fiber composite model of Kelly and Tyson is modgied to account for a changing distribution of fiber lengths during composite loading. The tensile properties at elevated temperatures were determined for the direc-tionally solidified eutectic oriented with platelets parallel to the tensile axis. The observed properties are attributed to the onset of plasticity of the CuAL2 phase above 150°C. DURING the investigation of whisker- and fiber-reinforced metallic matrix composites in recent years, two major problem areas have developed: 1) The fabrication of the composite involves tedious handling techniques in order to obtain a unidirection-ally aligned and uniformly spaced set of whiskers in the metal matrix. 2) Due to weak interfacial bond strengths or because of the formation of additional embrittling phases at the metal-fiber interface during long-time exposure or fabrication at elevated temperatures, many composite systems have exhibited considerably lower strengths than those predicted by a law of mixtures analysis.&apos; These problems have been bypassed by the technique of growing whiskers and plates of high-strength materials in a ductile metal matrix by controlled unidirectional eutectic solidification.2 The tensile properties of directionally solidified A1-CuA12 eutectic are presented here. This alloy consists of a ductile aluminum matrix, containing up to 5.7 wt pct Cu in solid solution, which is amenable to precipitation hardening by heat treatment and a reinforcing high modulus CuAlz intermetallic phase. The two phases are present in the form of alternating platelets or lamellae. The microstructural stability of this unidirectionally solidified alloy at elevated temperatures has been studied extensively.3.4 and preliminary tensile and bend tests have been reported. 5-7In the present investigation the tensile properties of the A1-CuA1, eutectic have been studied as a function of several ther-momechanical variables: solidification rate. heat treatment. rolling at elevated temperatures. and lamellar orientation. It was felt that the uniformity of structure and excellent interfacial bonding would give tensile properties concomitant with the metal matrix composite theory of strengthening proposed by Kelly and coson. 8-9 The tensile properties that were obtained point to a wide distribution of strengths for the CuAlZ platelets, which leads to large deviations from the predicted mechanical behavior for this composite. EXPERIMENTAL PROCEDURE Epitaxial Growth of Eutectic Alloy. The A1-CuA1, eutectic alloy was prepared by an epitaxial growth process. Sections of a master alloy ingot (total impurity content <0.008 pct) were placed in an alundum boat, melted. and directionally solidified to obtain a multigrained plate 12 by 2 by 4 in. This plate was tapered at one end to mate with a seed crystal 1; in. long and 4 by $ in. square. Then the seed-plate combination was placed in an alundum boat which sat in a quartz tube passing through the center of a horizontal resistance wound tube furnace. A dried argon atmosphere was maintained. The temperature gradient in the furnace was such that the liquid-solid interface of the eutectic alloy was located near the end of the furnace and could be observed through the quartz tube. Single-crystal plates were formed by melting the material back to the midpoint of the seed crystal of the desired platelet orientation and then epitaxially growing the plate from the seed by withdrawing the alundum boat from the furnace at a constant rate. This technique was used to produce aluminum and CuA12 lamellae parallel and perpendicular to the transverse direction on the plate. Metallographic examination showed that both phases were continuous across the original liquid-solid interface. It was also possible to grow a plate from two seeds placed side by side: and, although the lamellae of one seed were oriented at 90 deg to those of the second seed, the interface between the two grains remained parallel to the growth direction along the entire ingot length. Maintenance of a straight intergranular boundary during the solidification process was possible as long as both seeds were oriented with their original growth direction parallel to the solidification direction of the plate. Eutectic plates were directionally solidified at rates of 0.2, 1.0. and 4.7 cm per hr and sectioned transversely to the solidification direction to determine the apparent inter lamellar spacing of the lamellae. Metallographic examination was also employed

Jan 1, 1970

By J. S. Browning

The pegmatites of the Kings Mountain-Lincolnton, N. C., area constitute the largest known domestic reserve of beryl and spodumene. The reserve is estimated to contain 90 million tons of pegmatic material with 1,280,000 tons of recoverable Li2O (lithia) as spodumene.1 The pegmatites also contain 0.4 to 0.5 pct beryl disseminated throughout the orebodies. The pegmatites may contain a potential reserve of 240,000 tons beryl, equivalent to approximately 34,000 tons of BeO. Different flotation methods for separating beryl from feldspar or quartz, or both, have been developed by various investigators.2,3,4,5,6,7 On the other hand, published information is limited on concentration of spodumene-beryl ores. As the response of beryl and spodumene to flotation is essentially the same, a successful separation of the two minerals depends upon use of a selective depressant or a selective collector for one of the minerals.

Jan 7, 1961

By E. Posnjak

IT is rather the general belief that acidified, solutions of ferrous salts are readily oxidized when in contact with air, and often elaborate pre-cautions are taken to prevent it. This, however, is not the case and several statements may be found in the literature expressing surprise at the extreme slowness with which oxidation takes place when air or oxygen is bubbled through such a solution. Thus C. Baskerville and R. Stevenson1 "observed with surprise" that no oxidation apparently took place, as shown by titration with 0.5 N KMnO4, when a stream of air was passed for 3 hr. through an acidified solution of ferrous ammonium sulfate or ferrous sulfate. The same authors state that even the presence of salts such as. cobalt, chromium, copper, manganese, etc., which usually act as oxygen carriers, had "no effect upon the oxidation as was observed by passing air for 3 hr.. through solutions of Mohr&apos;s salt acidified with sulfuric acid." While this statement will bee proved further on to be at least partly incorrect the slowness of the oxidation of ferrous salts alone has been previously established by McBain.2 His investigation also showed that the rate of oxidation increases markedly with an increase in the concentration of ferrous sulfate as well as that of oxygen; the concentration of free acid had a comparatively small influence, which in the case of sulfuric acid was to retard slightly the rate of reaction. More recently R. Thomas and E. T. Williams3 investigated the catalytic effect of nitric oxide on the oxidation of ferrous salts, which had been earlier patented by McCulloch.4 They found that the probable mechanism of the catalytic action was the oscillation of the catalyst between two stages of oxidation and its interaction alternately with the oxygen and the ferrous iron.

Jan 12, 1926

By Dorsey Hager

One of the most interesting fields in North America was discovered, early in 1922, near the towns of Sunburst and Kevin, Toole County, Mont. This field produces oil from the Jurassic beds, which heretofore have been of but little importance as oil producers, and promses to be the

Jan 1, 1923

By Dorsey Hager

One of the most interesting fields in North America was discovered, early in 1922, near the towns of Sunburst and Kevin, Toole County, Mont. This field produces oil from the Jurassic beds, which heretofore have been of but little importance as oil producers, and promses to be the

Jan 1, 1923

By E. H. Kelton

THE purposes of this paper are to describe the use of adjustable cut and draw tools as a control test of drawing properties and to point out that no other well-known test or combination of tests determines this quality in zinc and zinc alloys. Rolled zinc has been used for making drawn articles, particularly battery cans, for many years. The development of rolling treatments satisfactory for, these purposes followed the usual course of trial and error experimentation depending upon cooperation with customers to determine what type of material was suitable. A quick test of drawing quality was highly desirable, of course. Scleroscope hardness and temper,1 having no apparent relation to drawing quality, were used simply to check the duplication of rolling treatment and grade of metal. The dynamic ductility1 test, on the other hand, was believed to be so like the drawing operation as to provide a reliable index and came to be taken as the criterion of good drawing properties. Faith in this test was strengthened by the fact that metal having the highest ductility was more satisfactory for operations, such as the manufacture of battery cups, that required several redraws. No distinction was made at that time in specifying metal as to whether it was to be subjected to simple cut and draw, redrawing or forming operations. It developed, however, that in some grades of metal the highest ductility did not coincide with the most satisfactory quality when the material was used for a single draw.

Jan 1, 1934

By A. Gemperle

Electron diffraction and transmission electron microscopy on foils at room temperature were used to investigate the ordering of Fe-Si alloys containing 10 to 23 at. pct Si. A certain degree of DO3 order was found in all alloys. With the exception of the lowest silicon concentration for which the antiphase domains could not be clearly resolved, the alloys have a domain structure of two-domain type with boundaries having 1/4a01<111> displacement vectors for less than 12.3 at. pct Si and with boundaries having 1/2 a0<100> displacement vectors for more than 12.3 at. pct Si. The alloys with 12.3 at. pct Si have a domain structure consisting of fine domains with 1/2a&apos;o<100> boundaries within much larger domains with 1/4a&apos;o<111> boundaries. The development of these structures can be explained by transition of the alloy from the disordered state into the B2-type order and then into the D03-type order by the mechanism proposed previously for the FeSAl alloys. The existence of the B2 structure in the lower part of the investigated concentration range reported in some articles can be explained by fine domains with 1/2a&apos;o<100> boundaries formed by several disordered planes within large domains with 1/4a&apos;o<111> boundaries. The ordered structure predicted by the theory —with practically no domain boundaries —is found in the alloys having 12.3 at. pct Si where it develops in the B2 structure region. ORDERING in Fe-Si alloys was first studied by phragmenl who found that beginning with 13 at. pct Si the DO3 (Fe3Si) superlattice reflections appear in the diffraction patterns. The equilibrium diagrams constructed later by corson2 and Haughton3 from various measurements proposed the existence of a homogeneous solid solution (a phase) in the range from 0 to 25 at. pct Si. Jette and Greiner4 and Farquhar et al.5 measured the relation between lattice parameter and composition and they considered the break in the curve at 9 to 10 at. pct Si to be caused by the ordered solution a"(Fe3Si). Glaser and Ivanick6 Determined critical ordering temperatures of the alloys containing from 10.9 to 27.9 at. pct Si from the measurement of the electric resistivity of quenched samples. In all cases the critical temperature was lower than the melting point and it was highest for 25 at. pct Si. Lihl and Ebel7 measured the lattice parameter curves at various temperatures up to 1000°C. The region between two breaks on these curves, corresponding to 10 to 12.5 at. pct Si at room temperature, was considered by them to be two-phase (a + a"). They concluded by extrapolation of the measured values that a" in the alloy having 25 at. pct Si is stable up to the melting point. Davies8 studied superlattice reflections in the X-ray diffraction patterns of an alloy containing 8.7 at. pct Si. He found the B2 structure and short-range order in the slowly cooled samples and the DO3 A. GEMPERLE is Research Scientist, Institute of PhysicS, Czechoslovak Academy of Sciences, Prague, Czechoslovakia. __Manuscript submitted January 2, 1968. IMD structure in the quenched and annealed samples. This investigation first reports the presence of the B2 structure, phase a&apos;: in Fe-Si alloys. Meinhardt and krisement9,10 also found its existence in Fe-Si alloys by neutron diffraction. No order was detected by them in the alloy containing 8 at. pct Si. The onset of B2 order was observed at a composition of 9.2 at. pct Si. They found almost perfect B2-type order with partial DO3-type order at room temperature in the 10 to 12.5 at. pct Si range and almost perfect DO3-type order in the 12.5 to 25 at. pct Si range. They established the critical temperatures Tc of both the structures through measurement at higher temperatures. The critical temperature for the B2 structure was found to be always higher than the critical temperature for the DO3 structure of the same alloy. They extrapolated the curves of the critical temperatures and concluded that the alloys with more than 17 at. pct Si have the B2 structure up to the melting point and the alloys with more than 23 at. pct Si have the DO3 structure up to the melting point. The results of Meinhardt and krisement9,10 were confirmed by Dokken&apos;s measurement" of the temperature dependence of the electrical resistivity in the 10.8 to 15 at. pct Si range. On the other hand chessin12 detected by X-ray diffraction a considerably lower degree of order in the 12.7 at. pct Si alloy. ANTIPHASE DOMAIN STRUCTURE IN ALLOYS WITH B2- AND DO$-TYPE ORDER The ordered structures B2 and DO3 can be described in terms of a subdivision of the bcc lattice into four fcc sublattices with a parameter double that of the bcc lattice. Following Marcinkowski13 we will label them I. 11, 111, IV. The B2 structure in the AB alloy is formed by placing A atoms on sublattices I and II and B atoms on sublattices III and IV. In a non-stoichiometric perfectly ordered alloy having concentration (A) > (B), A atoms occupy sublattices I and 11. and A and B atoms distributed at random occupy sublattices III and IV. The DO3 structure in an A3B alloy is formed by placing A atoms on sublattices I, 11, and 111, and B atoms on sublattice IV. In a nonstoichiometric, perfectly ordered alloy having concentration (A)/3 > (B), A atoms occupy sublattices I, 11, and 111, and A and B atoms distributed at random occupy sublattice IV. As further shown in Ref. 13, two types of domains are possible in the B2 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4 a&apos;o<ll1> only. Four types of domains are possible in the DO3 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4a&apos;o<111> and 1/2a&apos;o<l00>. Bethe14 suggested on the basis of theoretical considerations that in a structure with two sublattices at low temperatures only one domain should be present in the whole crystal at equilibrium. Similarly Bragg15 concluded that at low temperatures the domain struc-

Jan 1, 1969

By Magnus Troilius

The method of using the bromine process of determining sulphur in steel, described below, is in successful use at the Midvale Steel Works. Ten grams of drillings are weighed out and put into the 1/2-liter flask A, with long neck. The flask is connected with a wide glass tube C&apos;, which, in its turn, is connected with the absorption bulbs B, containing HCI, 1.12 specific gravity, and ahout 5 C.C. of bromine. The wide tnbe C causes the vapor to condense and flow back into the flask A during boiling. The bulbs B connect with a long glass tnbe, which may be made to carry off the bromine fumes through a hole in a window, or, better still, through a flue with powerful draught. The connections being made, 100 C.C. of boiling water are run in through the thistle tube T. The air is thus completely driven out of the flask. 100 C.C. of HC1 (about 1.19 specific gravity) are then run in. When the gas begins to run rattler slowly through B, heat is applied until boiling gradually ensues. The steel being completely dissolved, the apparatus is disconnected, and the contents of B rinsed out into a beaker of 100 C.C. capacity, into which a few C.C. of a concentrated solution of BaCI, have been previously introduced. Heat is then applied (best by means of the hot iron plate) until the bromine is completely driven off and the BaSO, has settled nicely to the bottom. The BaSO4, is then filtered off on a small

Jan 1, 1884

By G. Thodos, R. J. Smialek

A method has been developed that permits the correlations of Mehra and Thodos8 and Dastur and thodos2 for binary systems to be used for the prediction of the vapor-liquid equilibrium constants of the light and heavy constituents, Kland Kh, of a ternary hydrocarbon mixture. Furthermore, the unique relationship observed in this study, i.e., a plot of log Ke/Ki vs log Kp/K h is linear and passes through the origin, permits the calculation of the K-value for the intermediate component. This approach has been used to establish K-values for the constituents of the three ternary hydrocarbon systems used to develop this method and has also been applied to two additional ternary hydrocarbon systems to yield an average deviation of 7.7 per cent resulting from a total of 294 points for the five ternary systems considered. INTRODUCTION The rigorous calculation of vapor-liquid equilibrium constants for systems containing two or more components is a difficult problem and becomes extremely complex at elevated pressures and for conditions approaching the critical point. Although thermodynamic relationships can be developed to account for the vapor-liquid equilibrium behavior of simple systems, their use is limited because the necessary PVT data for these systems are not generally available. To establish a method for calculating K constants directly, without any recourse to the PVT behavior of a system, Mehra and Thodos8 applied the principle of corresponding states to the vapor-liquid equilibrium constants of binary hydrocarbon systems. They developed a series of charts which made possible the prediction of K-values for all binary hydrocarbon systems not containing methane. This work has been extended by Dastur and Thodos2 to include binary hydrocarbon systems containing methane. The charts developed in these two studies cover the high-pressure region and are applicable to conditions in the vicinity of the critical point. The ability of this approach to predict vapor-liquid equilibrium constants of binary hydrocarbon systems suggests that this method may be extended to the prediction of the K-values of the components of ternary hydrocarbon systems. In this investigation, the charts developed for both the methane and non - methane binary systems,2,8 together with mixture rules developed in this study, have been used to predict the K-values of the light and heavy components of a ternary hydrocarbon system. These calculated values are then used to establish the K-value of the intermediate component through the use of a novel relationship developed in the present study. DEVELOPMENT OF METHOD FOR PREDICTING K-VALUES OF TERNARY SYSTEMS The application of the corresponding state charts developed for binary hydrocarbon systems is restricted to those systems containing two components. The extension of these correlations to three-component systems requires that the ternary system be reduced to an equivalent binary, which can be treated in a manner consistent with the corresponding state development. To establish such an approach, the vapor-liquid equilibrium constant of the light component K is first calculated by assuming that the ternary mixture consists of the light component and a pseudo-heavy component of the intermediate and heavy constituents of the original ternary. To establish the vapor-liquid equilibrium constant of the heavy component Kh, the light and intermediate constituents of the ternary are combined to form a pseudo-light component of another equivalent binary system. The calculated values Kl and Kb are then utilized to calculate the vapor-liquid equilibrium constant of the intermediate component EQUILIBRIUM CONSTANT FOR LIGHT COMPONENT K To calculate the K value of the light (most

Jan 1, 1965

By R. L., Fullman

During the past year there have been a number of significant investigations that have furnished evidence on the driving forces governing grain growth and on the role played by boundary impurities. Thus Burke has shown that in high purity alpha brass the rate of grain growth in the earliest stages is approximately inversely proportional to the existing grain size. This relation agrees with one derived by Zener assuming that surface energy was the driving force in grain growth. Also in confirmation of the surface energy hypothesis, Burke found that growth virtually stopped when the grain boundaries or even only the grain corners were melted.

Jan 1, 1949

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore ex- ploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composi- tion laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, varia- tions are functions of distance. Hence, in either case, variations along the hole are of greater effect than across it.

Jan 1, 1949