Search Documents

By Gilbert Thiessen

THE purposes of this paper are (1) to show that the mineral matter content of coal is satisfactorily represented by the Parr formula; that is, Mineral matter = 1.08 Ash + 0.55 Total sulfur (2) to compare ash-to-mineral-matter ratios with factors by which ash values must be multiplied in order that dry, factor-times-ash-free values shall equal Parr unit coal values; (3) to examine such ash-correction factors and to compare them with similar factors corresponding to certain simplifications or modifications of the Parr formulas and (4) to show that ash-correction factors used for simplification in calculating approximate unit coal calorific values cannot be. correctly used for the conversion of other determined values in an analysis to the unit coal basis, but that each type of calculation requires separate treatment in simplification.

Jan 1, 1934

By Ralph V. Higgins

This paper concerns the magnitude of the amount of supersaturation that occurs in an underground reservoir during the flow of oil and gas to wells and to the amount of undersaturation that occurs during repres-suring of an oil reservoir where some effective permeability to gas exists. The study is based on earlier laboratory findings of other investigators on the rate of diffusion of gas in oil as a function of the depth of oil. Utilizing these relationships and the principles of reservoir mechanics, a quantitative estimate of undersaturation and super-saturation was calculated. The results showed that the diffusion of the gas is rapid enough that for all practical purposes no supersaturation exists during the flow of oil to wells or undersaturation during repressuring in reservoir sands having some effective permeability to gas. The reason diffusion of the gas virtually keeps the oil saturated is the long time required in radial flow for oil to reach the well and the slow rate at which pressure in reservoirs is increased during repressuring. INTRODUCTION Knowledge of the phase relationships during flow of gas and oil in an underground reservoir is essential to operating the reservoir in the most efficient manner. In material-balance calculations and in fluid-flow studies, the oil is assumed to contain all the gas that it will dissolve at given temperature and pressure. Pressure-volume-temperature relationships are normally obtained in the laboratory using "bottom-hole" or combined samples of the reservoir fluids. In such laboratory determinations equilibrium is obtained between the oil and gas in the pressure cells by mechanical agitation. During the flow of oil and gas in reservoirs, however, no comparable agitation occurs to mix thoroughly these fluids to aid in effecting equilibrium between the two phases. During repressuring of a partly depleted underground reservoir, the gas is usually injected into the reservoir faster than the oil can absorb it; consequently, the oil is undersaturated. On the other hand, as the oil flows through the reservoir to the wells during producing operations the pressure decreases faster than the gas in solution can diffuse through the oil to the gas phase. The oil therefore is supersaturated with gas. Where the oil is undersaturated, gas diffuses away from the gas-oil interface, and where it is supersaturated the gas diffuses toward the interface. In either case the gas moves from a higher to a lower saturation. This report contains the results of a study of the factors influencing the degree of nonequilibrium of the phase relations of oil and gas in porous mediums during the flow of oil through reservoirs to wells and also during the injection of gas into partially depleted sands. Data from an underground reservoir are presented and the degree of supersaturation during the flow of the oil through the reservoir to the well is approximated. Also data from another reservoir are used and the degree of undersaturation during the repressuring operation is calculated. In addition, the flow rates of oil in laboratory experiments and in underground reservoirs are compared, as data from the laboratory are often used to interpret events in the reservoir, and the rates of flow influence appreciably the degree of nonequilibrium. Much of the contents of this report was prepared in 1943; but, because of other activities during and since the war, the manuscript was left untouched until 1952, when it was decided to include an estimate of the amount of undersaturation during repressuring as well as supersaturation during flow.

Jan 1, 1955

By H. E. Ellis, O. L. Patterson, Granville Dutton

A large-scale water-injection program for the Holt Bryant reservoir of the Delhi field has been established by means of the new automatic multi-pool analyzer. The objectives of this program were to increase reservoir pressure and eliminate a cross-dip gradient of 200 psi. Pressure increases during the first 15 months of operation have allowed for increased oil production rates of 2,600 BID or 25 per cent. To determine the required water injection it was necessary to predict natural water influx ram. Elimination of the pressure gradients required the water-injection program to account for the fluid migration and pressure interaction between segments of the reservoir. An integral part of the ana1ysis included the determination of in-place volumes of oil and gas. The operation of the automatic multi-pool analyzer in determining the water-injection program is described. New features of the analyzer inc1ude an automatic maferial balance analog and a leart-squares computer for determination of unknown reservoir properties. Operational procedures are sufficiently simple to allow direct use by reservoir engineers on a routine basis. The rapidity and accuracy with which problems may be solved permit repeated ana1yses as a check upon reservoir performance. INTRODUCTION This paper describes the use of a new analog com- puter in determining the optimum injection program for a complex reservoir. The Holt-Bryant (Fig. 1) is the major reservoir in the Delhi field of Louisiana. Production is from the Tuscaloosa at subsea depths of 2,970 to 3,286 ft. The sand dips to the south and southwest from three to five degrees. The reservoir is approximately 12 miles long and varies in width from 1/2 to 2 miles. Various calculations have placed the initial volume of oil in-place in the wide range of 275 to 355 million STB. Two small gas caps were initially present in the reservoir. The Holt-Bryant reservoir was discovered in Dec.. 1944, and was fully developed with 188 producing wells by 1948. After development was completed, an east-west pressure gradient began to establish itself. This

Jan 1, 1957

Estimation of local recoveries is an important issue in a selective mining operation. Two techniques, probability kriging and multigaussian kriging, are applied to estimate local recoveries at Jerritt Canyon. The pros and cons of each method are discussed in light of the results. Both methods provide simple and satisfactory solutions to the problem of estimating local recoveries. Consequently, they can be useful tools to work with in a selective mining operation.

Jan 1, 1986

By John B. Miles

The present period of depression in the iron industry, with the resultant close approximation of the cost of production to the selling-price of pig-iron, should make the discussion of this subject at this time not only interesting but profitable. It is possible that it may result in the collection of data, which when added to those set forth in this paper will clearly indicate the influence of the rate of driving a blast-furnace upon its fuel-economy. The question is not whether an excessive rate of driving (meaning a rate definitely in excess of the average rate in the United States) results in an increase in the fuel-consumption, but rather whether a rate considerably less than the average does not result in a marked decrease in the fuel-consumption. The commercial and metallurgical sides of this problem must be kept separate. With a large margin between the cost of production and the selling-price of pig-iron, and a plant already in operation, it is frequently profitable to sacrifice a couple of hundred pounds of fuel per ton of pig-iron in order to secure the greater gross profits resulting from a larger tonnage. When this margin decreases with a plant in operation, or when the determination of the size of a new furnace intended for a certain production confronts the management, a clear understanding of the effect of the rate of driving upon fuel-economy becomes necessary. If it be granted that slow driving leads to low fuel-consumption, it should be borne in mind in the design of a new plant for the production of a certain tonnage that the adoption of an economical rate of driving increases only the size of the furnace proper, whereas, due to the decrease in quantity of blast required on account of the decrease in fuel burned, the stoves, the blowing-engines, the boilers and the piping may be de-

Jan 1, 1909

The following is a partial list of members and guests who called at Institute headquarters during the period July 10, 1917, to Aug. 10, 1917: G. A. Collins, Seattle, Wash. Norman Picot, Melbourne, Aust. A. D. R. Galloway, Komfrodua, W. Africa. W. E. Pomeroy, El Paso, Tex. F. Lynwood Garrison, Philadelphia,; Pa. Francis R. Pyne, Elizabeth, N. J. Geo. M. Henderson, Bland, N. M. W. L. Remick, W. Norfolk, Va. L. B. Herr, Jr., So, Bethlehem, Pa. M. F. Sayre, Schenectady, N. Y. Zay Jeffries, Cleveland, 0. Leighton Stewart, New York, N. Y. H. H. Lauer, Allentown, Pa. Randolph D. Talmage, Joplin, Mo. Wm. B. McKinlay, Yonkers, N. Y. H. J. Volker, Ossining, N. Y. A. N. Mackay, Republic of Colombia. Dwight E. Woodbridge, Duluth, Minn. Edmund Newton, Minneapolis, Minn. Kwong Wu, Peking, China. J. N. Acosta has resigned his position as mining engineer for the Shannon Copper Co., Gleeson, Ariz., and is now engaged as consulting engineer for Lower California, Mexico, with headquarters at San Diego, Cal. L. D. Albin, formerly assistant general sales manager of the Ingersoll-Rand Co., was appointed general sales manager on July 25,1917.

Jan 9, 1917

By M. Albertson

At Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 m.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 m.), the width at the lower lobe was about 1000 ft., and the width at the narrows probably 400 to 500 ft. The original depth of water varied from 20 to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the lake. About 1,500,000 tons of mill tailings, composed of sands and slimes, were discharged into the lake's waters previous to 1915. Most of this material

Jan 1, 1921

By R. M. Schuster, F. M. Benavides

This study compares the costs of transporting coarse coal by pipeline versus more conventional belt conveyors. Hydraulic conveying of crushed (not pulverized) coal has not had widespread commercial acceptance. However, there is little doubt that the technology is available, so that, should this method be proven economical for a given application, implementation will become more acceptable.

Jan 1, 1984

JAMES E. HOWARD,* Washington, D. C. (written discussion?). -Mr. Comstock, in his classification of the possible causes of transverse fissures, has not quite caught the point of view of the writer. It appears, following the trend of thought in Mr. Comstock's paper, that three groups instead of two might bee enumerated, namely: Fatigue of the steel, quality or, preferably, grade of steel, and mill practice. All steels are liable to failure by fatigue. Stresses that are capable of causing fatigue fractures are modified in their magnitude by the grade of steel acted upon. Mill practice is a term having a very wide meaning and in its relations to the development of transverse fissures has been used with such vagueness as to include many known factors and some that are unknown in the arts. According to the grade of steel employed, fatigue fractures may be accomplished by loads of greater or less magnitude, hence there is a relation between quality, or grade, of steel and the display of fatigue fractures. Mill practice of such an order as to affect the formation of transverse fissures must be shown to exert an influence on the ability of the steel to endure repeated stresses. Different grades of steel are selected for different purposes. Steel employed for fire-box purposes is of different grade from that used for cutting tools; although each grade is suitable for its purpose, and therefore of good quality. It is conceivable that a demand might be made for steel of physical properties in excess of those of any known grade. Under such a demand, impossible of' fulfillment, it would not be proper to refer to the steels as being deficient in quality; to do so would be a failure to recognize that all steels have their limitations in strength. Service conditions peculiar to rails admit of successive advance until the conditions can no longer-be met. The failure of a large number of rails from one type of failure, when all known means of averting the failure have been employed without success, is sufficient evidence that the end is close at hand. Iron rails, for a time, successfully met the requirements of railway service but weight of equipment, motive power, and rolling stock were increased, necessitating the use of steel. The early steel rails enjoyed the reputation of being of excellent quality, although: neither chemically nor structurally would they be so regarded ,lit the present time. They did good service in their day and under the conditions then prevailing were good rails. To meet the increased weight of rolling stock there has been

Jan 3, 1919

By Albert Stazicker

AT Climax the warehouse department operates as an independent unit similar to the mine and mill departments. It has the responsibility of receiving, checking, unloading, and storing all material and supplies delivered to the plant. In addition, the transportation of all supplies comes under the direction of the warehouse so that prompt delivery of supplies to all departments is one of its major functions. The transportation division operates heavy and light trucks, trailers, two large tractors, and two snowplows. In addition to delivering supplies it is also responsible for snow removal from the roads, hauling of sand and gravel for concrete and domestic coal to employees. and all miscellaneous work involving the use of tractors or trucks.

Jan 1, 1946

By S. Storchheim

MORE and more attention is being paid to the bonding of metals in their solid states. For a better understanding of this technique for joining metals and how it is affected by changes in temperature, pressure, and time at temperature and pressure, a detailed report concerning nickel to aluminum bonding has been published.' In order to broaden the knowledge accrued, some additional work concerning solid state joining of aluminum to copper and aluminum to zirconium was performed. The investigation of the Al-Cu system was considerably more extensive than the investigation of the Al-Zr system. For the A1-Cu system, not only were tensile sudies made but intermetallic penetration rate investigations also were carried out. The effect of temperature on intermetallic penetration rate for the A1-Cu system was determined at 11 tsi pressure, held 2 min. Procedure Apparatus: The hot pressing technique was the means of solid state reaction used and required the equipment depicted in Fig. 1. The following procedure was involved: The two metals to be reacted were placed in an aquadag-lubricated 18-4-1 tool steel die, 16 in. high by 1.440 in. ID, between punches of 1.366 in. diam made of the same material. A thermocouple well was located in the die body 3½ in. down from the top of the die, while another well was located centrally in the bottom punch 8½ in. from the bottom of the die. This die assembly was located in three cylindrical ceramic heating furnaces placed in tandem. Each furnace was controlled individually by a Variac power transformer. In turn, the die and furnaces were placed in a water-cooled stainless steel pot which could be evacuated. A cover, which contained a centrally located Wilson seal with an 18-4-1 1 in. diam ram running through it, was bolted on the pot. After sealing, the pot was evacuated by a roughing pump to 200 microns pressure, after which a diffusion pump was used to bring the pressure down to 5 to 15 u. At this pressure, the furnaces were turned on. As soon as they started to heat, out-gassing of the entire unit raised the pressure to 30 to 400 p. By the time the specimens were at temperature ready to be pressed, approximately 4/2 hr, the vacuum pumps had re-established the 5 to 15 u pressure. Once the desired temperature was reached, the required pressure was applied for a predetermined length of time to the 1 in. ram, through to the top punch, and to the specimen. When the time for keeping the specimen under pressure had elapsed, the pressure was released, the energizing coil current turned off, and the assembly allowed to cool. After cooling, the die was removed from the pot and the specimen was ejected. Specimen Preparation: Two different types of specimens were made for this investigation. One was for subsequent tensile testing, while the other was for determination of intermetallic alloy zone penetration into the parent metals. Tensile Bars—Commercially rolled copper pieces in. thick or zirconium sheet pieces 1/32 in. thick and 1.366 in. diam were placed between commercial 2-S aluminum rod 1 in. thick and 1.366 in. diam. This sandwich in turn was slipped into a 2-S aluminum sleeve 1.438 in. OD and 1.370 in. ID. This sleeve lined the couple up and prevented the aquadag lubricant from getting in between either the A1-Cu or Al-Zr interfaces. Immediately prior to the specimen assembly, the copper or zirconium was abraded on the flat surfaces with 320 grit silicon carbide paper, producing clean smooth surfaces. The aluminum was chemically cleaned just before assembly by: l—degrease in acetone, 2—distilled water rinse, 3—immersion for 3 min in 5 pct NaOH at 70" to 80°C, 4—distilled water rinse, 5—immersion for 2 min in 50 pct HNO3 solution at room temperature, 6—distilled water rinse, and 7—drying in a blast of gas. After the A1-Cu sandwiches were hot pressed and ejected, the specimens were machined such that the aluminum sleeve was removed, and the remaining aluminum was then threaded; the bar so produced was tested later for tensile strength. In all the instances where Al-Cu couples were tested, the specimens broke during the test at the Cu-A1 interface and never within the aluminum or copper. The ultimate tensile strength values at times showed considerable scatter for a set of given reaction conditions. Because of this, as many as three to five specimens were made for a particular set of conditions. The trend of the average tensile strengths obtained was not as conclusive as was the trend of the maximum tensile strengths, the latter values being obtained under optimum reaction conditions. Therefore, the values of ultimate tensile strength given herein are maximums.

Jan 1, 1956

By W. Joseph Schlitt

The types of copper leaching and recovery operations in the United States are reviewed, along with characteristics and trends in the industry. The contribution of the various leach operations to total mine output is discussed in order to provide a perspective on the relative importance of copper leaching as a method of production.

Jan 1, 1980

By J. W. Koger, R. E. Hurnrnel

QUENCHED, bcc p brass, P1, transforms to a mar-tensitic phase, when it is cooled below room temperature.' This transformation can be followed using resistance measurements since the resistivity of the martensitic phase is considerably larger than that of the parent phase, Fig. 1.' phillips3 first reported that, when Cu-Zn alloys containing between 37.0 and 39.0 wt pct Zn were quenched from the 0 region to room temperature, variable amounts of a phase could be observed depending on the mode of quenching. If the quench occurs very rapidly, the a phase forms by a "massive transformation". The resultant phase has the same composition as the high-temperature P phase from which it was formed. If the quench is less severe, the alloy is retained largely in the p form; however, some a is formed by precipitation. In this case, a contains more copper than the high-temperature 0 phase from which it has formed. The a phase most probably does not undergo a transformation in the temperature range where p transforms to low-temperature martensite. This can be deduced from the Eesistivity-temperature relation which is linear in this temperature range, Fig. 2. The stable a phase which is present along with R. E. HUMMEL is Assistant Professor, Department of Metallurgical and Materials Engineering, University of Florida, Gainesville, Fla. J. W. KOGER, Junior Member AIME, formerly with University of Florida, is now with Oak Ridge National Laboratory, Oak Ridge, Tenn. Manuscript submitted December 13, 1967. IMD.

Jan 1, 1969

By F. C. Bond

B. H. Bergstrom (Allis-Chalmers Mfg. Co., Milwaukee)—In reading this article, it was difficult to follow through the example given as a starting point in the derivation of the theoretical equation which relates ball size to feed size. A discussion with F. C. Bond led to the following clarification: Bond postulates that "the breaking force exerted by a ball varies ... as the cube of its diameter . . ." and that the force in pounds per square inch required to break a particle varies ... as its diameter squared." He concludes: "It follows that when a l-in. ball breaks a 1-mm particle, a 2-in. ball will break a 4-mm particle, and a 3-in. ball a 9-mm particle." The above example can be true only for a different set of assumptions. Since the first assumption is apparently true, it is the second that must be revised. The second assumption should read that the breaking force required to break a particle varies as its diameter to the 3/2 power. This relationship was derived in the next paragraph of the article.

Jan 1, 1960

By J. H. Swartz

During 1938 and 1939, an extensive series of geophysical surveys, employing both resistivity and magnetic methods, have been carried on in the Hawaiian Islands by the Section of Geophysics of the United States Geological Survey in cooperation with the Division of Ground-Water of the Survey and the Division of Hydrography of the Territorial Government (see Fig. 1). During this time, surveys have been conducted on the islands of Oahu, Molokai, and Maui. Two distinct types of ground-water occurrence are being investigated: (1) The basal fresh-water lens floating on underlying salt water in obedience to the Ghyben-Herzberg principle (Fig. 2); and (2) perched ground-water (Fig. 3).

Jan 1, 1940

By C. M. Loeb, A. M. Gaudin, J. H. Brown

R. E. Carter (General Research Laboratory, Schenec-tady, N. Y.)—Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crys-tallographic directions, and in materials containing quartz because of the a-p' transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 1, 1960

By E. M. Cox, A. S. Skapski, N. H. Nachtrieb, M. C. Bachelder

As a result of using copper-containing scrap in the steelmaking process, the copper content of steels has been steadily increasing for years. Consequently the possible role copper may play in the steelmaking process and in the finished product begins to attract the metallurgists' attention. Some time ago one of the present authors forwarded the idea—based on the results of the analysis of nonmetallic inclusions extracted electrolytically from steels—that sulphur in plain carbon steels is distributed mainly between copper and manganese, the amount of iron sulphide being very small; and that, consequently, the problem of copper and that of sulphur in steel cannot be treated separately.' At the time of the publication of the quoted paper little was known about the relative affinities of copper and manganese for sulphur at high temperatures except that at moderate temperatures (below 1000°C) the affinity of manganese for sulphur is much greater. To gather more experimental data on this subject, the present authors undertook the investigation of the equilibrium constants of the reactions: 2Mn(8 or 1) + S2(g) = 2MnS(s) 4Cu(s or 1) + S2(g) = 2Cu2S (S or I)* 2Fe(s) + S2(g) = 2FeS (s or 1) over a range of temperatures wide enough to establish the dependence of these equilibrium constants on temperature. From the equilibrium constants (K = l/Ps2) the free energy of formation (affinity) can be calculated from F° = -RTln 1/PSt (1) where the standard conditions chosen are: 1 atm of sulphur pressure and the activities of condensed components equal one. The decomposition pressure, Ps2, of sulphur over the respective sulphides is too small to be measured directly, but there is a way of eliminating this difficulty by measuring the equilibrium constant of the reaction between the sulphide and hydrogen. From the latter and from the equilibrium constant of the thermal dissociation of H2S we then calculate Ps2 for the respective sulphide. 2Mn + 2H2S = 2MnS + 2H, 2H2 + S2 = 2H2S_________ 2Mn + S2 = 2MnS The numerical values of the equilibrium constant of the thermal dissociation of H2S at different temperatures were taken from Kelley's paper, "The Thermodynamic Properties of Sulfur and its Inorganic Compounds."² In previous experimental work published by Jellinek and Zakowski3 and by Britzke and Kapustinsky4 the equilibrium constants of the reactions Metal sulphide + H2 = H2S + metal were determined by passing hydrogen, at different rates of flow, over the sulphide, analyzing the resulting H2S + H2 mixture and then extrapolating the H2S/H2 ratio (which is a function of the rate of flow) to the zero speed of flow, a method necessarily involving considerable uncertainty. In the present work the equilibrium ratio was actually measured instead of being extrapolated. The apparatus is shown in Fig 1. Experimental Procedure The sulphides were prepared by the following methods: FeS Powdered iron which had been reduced with hydrogen (ferrum reduc-tum) was mixed in stoichiometric ratio with sublimed sulphur and carefully ground. The mixture was put into an alundum crucible, covered with pure sulphur, and the reaction started by touching the mixture with a glowing iron rod. After the reaction was completed the product (still containing some metallic iron) was again ground with sulphur, put into a Rose crucible, covered with sulphur, and heated in a strong current of pure hydrogen. Analysis of the final product showed 62.46 pct Fe and 36.59 pct S. Theoretical for FeS: 63.53 pct Fe and 36.47 pct S. MnS Manganese sulphide (precipitated and carefully washed with distilled water containing H2S) was dried in a Rose crucible in an atmosphere of H2S and heated in a current of hydrogen for 2 hr at red heat. The product was then ground and ignited for several hours at 1000°C in a current of hydrogen sulphide. Analysis showed 64.53 pct Mn and 36.63 pct S. Theoretical: 63.15 pct Mn and 36.85 pct S. Some MnS samples were prepared from metallic manganese and sublimed sulphur by mixing and grinding them and then heating in a current of hydrogen sulphide in an alundum tube.

Jan 1, 1950

By R. H. Card

THE geophysicist is interested greatly in the resistivities of different formations or parts of the earth's crust; sometimes he is interested in a single figure in the nature of an average, or what may be called the effec-tive resistivity, of all the formations or parts of the crust at a given location to a certain depth. Conversely, the engineer whose work is concerned with the coordination of power and communication lines in such a manner as to avoid electrical interference between these two types of facilities is concerned very much with this effective resistivity; to a lesser extent he is interested in the resistivities of individual forma-tions. In connection with his work the coordination engineer often estimates the effective resistivity; of the earth from measurements of the mutual impedances of lines; in other instances he derives front measure-ments of a different type the resistivities of different layers of the crust and synthesizes these to obtain an estimate of the effective resistivity. In connection with problems concerning the coordination of power and telephone lines, measurements from which earth resistivities can be estimated have been made at many points in the United States by the American Telephone and Telegraph Co. and its associated companies, in cooperation with various power companies and with railroad companies having electrified sections of line. Other such measurements have been made by the Joint Subcommittee on Development and Research of the Edison Electric Institute and the Bell Telephone System. A study has been made of the correlation of these data with the ages and types of materials of the strata of the earth's crust at each of the test locations. The purpose of this study has been primarily to provide information to assist in predicting the order of magnitude of effective resistivities to be used in the preliminary consideration of problems con-cerned with the coordination of power and communication lines. To make the results of such a study, most useful, it is essential that the geo-logical data to be secured when such a prediction is wanted be readily obtainable. Data on the ages of strata and the types of materials com-posing geological structures can usually be obtained, therefore particu-

Jan 1, 1937

HAVING already shown you the methods of making the moulds for casting and how they are to be prepared so that they may receive the melted metals well, it is now necessary, in order to complete the casting with perfection, that I show you not only the operations and instruments by which metals are softened, but also how metals can be made as liquid and fluid as water so they may easily enter into all the hollows of the moulds that you have made. Of these, besides the fire which is the prime agent, there is a very powerful furnace, which is called a reverberator.* I believe this is chosen not only for convenience but also because it is necessary in large casts. This is made of baked bricks, or of crude ones if desired or of suitable fire-resistant stones. Although all masters have the same objective, each one proceeds to make this kind of furnace according to his own ideas so that it can be said that there are almost as many different shapes of such furnaces as there are masters. This can be seen in the place that contains the metal, which is of such a shape that the force of the fire may operate better. Thus some masters are called good who, seeing no farther than what has been shown them, make them circular like a bread oven. Some others make them oval across the fire en- trance, while others extend them lengthwise. Also, there are some who make a single outlet for the flames, some two, and some three. Some make the entrance for the fire high and narrow and others, wide and low. The same is true of the place where the flames are generated, which is called the firebox. Some put the wood in from the side, some lengthwise in the same direction as the entrance for the flames, and some from above by means of a little hole. Also, one makes the vault low, and another makes it high. And while one puts an entrance for air underneath so that the

Jan 1, 1942

By Frederic H. Lahee

After abandoning two dry holes, on the Mrs. Daisy Bradford land, C. M. Joiner finally completed his No. 3 on Sept. 8, 1930, at a total depth of 3592 ft. This well is 735 miles somewhat north of west of the town of Henderson, in Rusk County. Between Oct. 2 and Oct. 6, this well made numerous heads which indicated that it would produce about 300 bbl. daily. By Nov. 27, two dry holes,' completed near the Joiner well, taken in conjunction with the small production from this well, served to dampen any enthusiasm among those who hoped for a major pool; but by December 18 three other producers had been completed. On Dec. 28, 1930, E. W. Bateman's Lois Della Crim No. 1 drilled itself in with an estimated daily yield of between 10,000 and 15,000 bbl. from a depth of 3650 ft. This well, 10 miles north of the Joiner well, also in Rusk County, initiated the leasing campaign that led to the later orgy of drilling. On Jan. 25, 1931, Moncrief, Farrell and others completed their J. K. Lathrop 1 as another big producer, 7 miles east of Gladewater in Gregg County and 14 miles N. 20" E. from the Bateman Crim well. The Lathrop well, 3574 ft. deep, flowed 320 bbl. in 1 hr. through a ½in. choke. The first well completed in Smith County was Cook No. 1, drilled by Guy Lewis et al. in the James Jordan Survey, 4.7 miles west of the Joiner discovery well. On Mar. 30, 1931, it flowed 137 bbl. in 33 min, through a ¾-in. choke. The top of the pay sand was found at 3672 ft. Finally, in Upshur County, on May 5, the Mudge Oil Co. et al. completed the Richardson No. 1, which flowed 274 bbl. through a 4 2/64-in. choke in 2 hr. This well is 4 miles northwest of the Lathrop producer. Development It is unnecessary to give a lengthy description of the rapid development of the area discovered in these five far-separated wells, or to discuss the speculations offered as to whether there were several pools or only one.

Jan 1, 1932