Search Documents

By R. A. Spitz, T. C. Frankiewicz, R. E. Lueders, D. S. Davies

Further development of the Nitric-Sulfuric Leach (NSL) process has led to an improved design of the leach and nitric acid recovery steps. NO produced in the leach step is reacted with oxygen, regenerating NO2, which is sparged directly into the leach reactor. Leaching is simplified to two steps, and the nitric acid plant is replaced with an oxidation recycle gas system. Laboratory work substantiated the concept and led to selection of operating conditions. The lab work also pointed to improved process control compared to use of nitric acid as the sole oxidant. Recovery of copper from purified pregnant liquor is modified to use air agitation electrowinning improving cathode quality and lowering tankhouse costs. Economic evaluation shows reduction of capital requirements from $2640 per annual ton to $2220 per annual ton in 1978 dollars for 45 kt/a of copper production.

Jan 1, 1982

By J. A. M. van Liempt

SINCE the discovery, of von Laue, that a crystal forms a natural grating for X-rays, our knowledge of the structure of solids has gone forward with rapid strides. This progress is not only of purely scientific interest, but has also yielded direct technological results. One of the most valuable results is the broadening of our knowledge of the structure of pure metals and alloys. To promote these studies it is often desirable to have at our disposal pieces of metal consisting of one single crystal. As is so often the case in the natural sciences, we obtain the best results by making our earliest experiments on pure, simple materials and avoiding unnecessary complications. The Cryogen Laboratory at Leyden followed this method with much success, because the work was done at such low temperatures that the heat movement of the atoms was almost' absent. Similarly we can simplify the studies of metals by leaving out of consideration the influence of the grain boundaries and the mutual influence of the crystals by using unicrystalline instead of polycrystal-line metal. Methods of making single crystals have been scientifically studied during the past few years. Some methods were already known in the arts, but these have been improved and new methods have been developed. The methods for making metallic single crystals may be divided into the following groups: A. From the liquid state B. From the gaseous state C. Electrolytically D. By recrystallization in the solid state

Jan 1, 1927

By Donald C. Branford

The place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past Io years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. Divisions in Definition or Field of Geophysics Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of fmancial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or SO of the earth's crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1946

By Donald C. Branford

The place of geophysics in the curriculum of a college or an engineering school has been much discussed. There is uncertainty as to whether the graduate may be called a "geological geophysicist" or a "geophysical geologist." Some have used the term "geophysical engineer." The question of the specialized undergraduate curriculum versus a general undergraduate training in the parent sciences with the addition of cultural electives has been and is still being argued. The literature during the past Io years shows that there are two rather definite schools of thought on this subject. The prospective employer, engaged in active geophysical exploration, visualizes the graduate in terms of the routine work he will do in the field. The school administrator, grounded in many years of tradition in the cultural type of education, visualizes the graduate in terms of his position in a political and cultural society as well as in his work as a professional geophysicist. Both are right and both wrong. A third school of thought, that of the student himself, has been almost totally ignored. It would seem best, for the purpose of this paper, to treat these various points and allied material separately, and then to integrate the conclusions as a set of conditions that should be fulfilled as far as possible in the ideal curriculum. At the end the relationship of our findings to the curriculum that has been tentatively adopted at the University of Pittsburgh will be considered. Divisions in Definition or Field of Geophysics Geophysics is that field of science in which geological and earth problems are solved with the use of physical and chemical techniques. Altogether too much attention has been paid to the artificial separation in this science of the commercial applications from the so-called "pure" or academic geophysics. The only real difference in the two types of work is one of scale of operations. In the commercial field the scale is large in terms of fmancial backing, immediate economic importance, and speed of operations. In the academic field the scale is large in terms of breadth of interests, in eventual economic importance, and length of time allowable for theoretical investigations. In exploration work the scale is small in terms of dimensions, since the methods are applicable only to the outer 20,000 ft. or SO of the earth's crust. In academic work, the student is not pressed for results of immediate economic importance, and therefore can afford to spend more time on problems that seem unimportant at the time. In the sense of background knowledge of the parent sciences necessary to the geophysicist, no essential difference can be found. Physics, chemistry, geology, and mathematics together, and in their proper proportionate amounts, form the matrix from which geophysical ideas and methods may spring.

Jan 1, 1946

By H. Brevers, Maurice Rey

Through circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. Flotation of Realgar Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arseno-pyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed non-polar and the other polar, a distinction that has been stressed in a previous paper.' Depression of Realgar and Flotation of Cinnabar Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1943

By Maurice Rey, H. Brevers

Through circumstances connected with the war, the senior author lost his records, therefore it has been impossible to include numerical data in this paper. The arsenical quicksilver ore investigated had been roasted, with poor metallurgical results. The vapor-tension temperature curves of mercury and arsenious trioxide are similar, and the arsenical compound hampers the coalescence of mercury drops in the condenser and is the cause of large stack losses. The ore was a gray limestone carrying small amounts of carbon and mineralized with cinnabar and two arsenic minerals, realgar (As2S2) and arsenopyrite (FeAsS). The proportion of realgar often exceeded that of cinnabar; the proportion of arsenopyrite was smaller. The grade of the ore varied between 0.8 and 4 per cent Hg. The problem was to make a high-grade mercury concentrate, as free from arsenic as possible. The water used throughout the testing was hard, having a pH of about 8. Flotation of Realgar Realgar showed a very strong tendency to float. It formed a film at the surface of the pulp and floated in abundance with only pine oil. Therefore an attempt was made to float the realgar before the cinnabar, but this was not very successful; the percentage of mercury in the realgar concentrate could never be brought below 2 or 3 per cent. Cinnabar slimed easily and floated with pine oil, so that some of it always accompanied the realgar. There was also the question of the cinnabar-arseno-pyrite separation. On further investigation it was found that realgar can be floated not only with pine oil but even better with a combination of hydrocarbons and pine oil. Washing the ore with ether revealed that it contained hydrocarbons, which helped to float the realgar. In this connection it belongs to the same class as carbon, sulphur and talc. It can be floated also with a xanthate, when activated by a heavy-metal salt. The conditions favoring the two types of flotation are opposed, as activation by a copper salt facilitates xanthate flotation (in fact, is even necessary to it), whereas it hinders pine oil and petroleum flotation. One type of flotation can be termed non-polar and the other polar, a distinction that has been stressed in a previous paper.' Depression of Realgar and Flotation of Cinnabar Many chemicals were tested in an attempt to float the cinnabar and depress the realgar. Finally starch rendered soluble with caustic soda was tried, also several grades of commercial soluble starch, and dextrin was found to be the best and the most convenient reagent. Several of these starch preparations have a strong flocculating effect on the pulp, which is a distinct disadvantage. Dextrin, with its low flocculating power, is excellent. It is noteworthy that starch preparations are also depressants for carbon and talc, so that the fact apparently has a general

Jan 1, 1943

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).¬A study of this paper raises a question on which it is hoped Mr. Stork will throw more light; that is, why does an oxygen content generated on poor melting conditions have a deleterious effect on the properties of the iron, while an oxygen content generated by the oxidation of steel scrap in the cupola is beneficial to the strength and chilling ability? In each case the oxygen is absorbed at the same time and place in the process of melting and it is by no means clear why the superiority of semisteel should be assigned solely to its oxygen absorption, when oxygen absorbed without the steel addition is admitted to be injurious. It is not apparent why oxygen caused to be absorbed by the steel addition should not pro-duce the effects of burning, sluggishness, slag inclusions, gas occlusions, etc., the same as oxygen absorbed by the iron in the cupola for any other reason, and it would seen that other factors to which he has not given sufficient emphasis must enter into the author's results. To an impartial reader of this paper, who was most favorably inclined toward J. E. Johnson, Jr.'s theory of the improvement of cast iron by oxygen, the discrepancy in the author's reasoning or statements is difficult to accept, and it is hoped that an explanation will appear in the final discussion.

Jan 11, 1919

By A. Ahmadieh, J. E. Dorn, Jack Mitchell

A detailed investigation of the disloccrtion mechanisms controlling prismatic, slip in a solid solutions of magnesium containing up to 15.9 at. pel Li revealed that low-temperature prismatic slip is controlled by the Peicrl's mechanism for all alloy compositions. At higher temperatures slip in the 7.9 at. pet Li alloy was found to follow the diclates of the cross-slip mechanism from basal to prism planes, while the higlier-lilhium alloys exhibited an athermal dejormation process which might be due COARSE-GRAINED polycrystalline aggregates of distilled magnesium exhibit very limited ductility at low temperatures.' The ductility of polycrystalline magnesium, however, is much improved by solid-solution additions in excess of about 8 at. pct to shot-range ordering. The major effect of lithium additions on the low-temperature Shear] stress. for prismatic slip appears to be due to its efftct in lowering the Peierl's stress whereas (1 increase in the shear stress with increased lithium conlent at higher temperatures might he due to short-range order strengthening. Additions rip to 7.9 (at. pel Li appear to have only minor effects on the slackiug-jaidt energy. Li.2 Although the relative amounts of basal slip and twinning are not materially altered by such alloying, a substantial change takes place in the relative amounts of prismatic slip. Whereas prismatic slip is negligible and limited to regions of high stress concentrations in the vicinity of the grain boundaries in pure magnesium, extensive prismatic slip over entire grains occurs in the higher lithium content alloys. Furthermore, as the lithium content is increased above 8 at. pct, the flow stress for polycrystalline aggregates decreases. Comparison of the single-crystal data on pure magnesium for basal slip by Sheely and Nash3 and those for prismatic slip by Flynn, Mote, and Dorn4 indicates that the critical resolved shear stress for prismatic slip is much above that for basal slip.

Jan 1, 1965

By H. C. Rickaby

BY August 1944 Canada expects to be shipping 56 percent hematite ore from its new Steep Rock iron mine, via Port Arthur on Lake Superior, to the steelmaking centers in Canada and the United States. This is indeed welcome news to steel men, especially if they operate open hearth furnaces, as the Steep Rock ore is a high-grade lump and will be valuable as charge and feed ore. But better news is the fact that this first big producer of high-grade hematite ore in Canada, since the exhaustion of the Helen mine in the Michipicoten area north of Lake Superior in 1918, has a proved ore body of 16,757,000 long tons and a probable ore body of 14,000,000 long tons, thus giving an over-all total of 30,757,000 long tons and assuring production for a number of years to come.

Jan 1, 1943

By C. E. Shoenfelt, D. E. Winchester

NO important discoveries of petroleum during 1933 were reported from New Mexico. Lea and Eddy counties were the centers of activity during the drilling season and each had a number of interesting completions. The Hobbs pool, in Lea County, was definitely outlined on the east, north and northwest. Under an agreement reached last summer by state officials and operators, the Hobbs pool was continued under proration throughout the year. One hundred eighty-four units of 40 acres each were being produced at the end of 1933. The allowable was 21,306 bbl. daily at the beginning of 1933, but when the agreement was revised in the spring the minimum was raised to 30,000 bbl., and by the end of the year had been raised to 33,473 bbl. At present the field is being prorated on the basis of 25 per cent on acreage and 75 per cent on potentials except in the southwestern edge of the field, where water encroachment is a problem. In this area the basis of proration is 40 per cent on acreage and 60 per cent on potentials. A corrective method employed in this part of the field has been partly successful. The water is advancing in the upper part of the pay, a dolomitic limestone, and in a number of instances packers have been set in the pay below the water and above the oil. The locating of a satisfactory seat for a packer is difficult and in some instances has not been a complete success. Pipe line runs from the field during the year aggregated 11,413,218 bbl., bringing the total gross production up to 41,093,681 bbl., of which 39,000,-000 bbl. has been produced under proration, which went into effect on July 10, 1930. On Nov. 30, potentials were determined on the assigned pressure basis and the total was reduced 71,165 bbl. daily, to 1,265,-332 barrels. The outstanding completions in the Hobbs pool were three in number, of which the best was the Humble Oil & Refining Company's No. 3B Bowers in sec. 20, 18S., 38E., with an initial production of 11,664 bbl. of oil and 10,000,000 cu. ft. of gas. The Shell Petroleum Company's No. 4B McKinley, in the same section, produced at the rate of 22,940 bbl. of oil while flowing open, but when tubed, flowed at the rate of 6610 bbl. The third outstanding well, No. 4 Hardin of the Tidal Oil Co., and located in

Jan 1, 1934

By HAROLD E. WHITE

LONG before the Stone Age, when man first sought shelter where there-were no natural shelters, such as caves and clefts in the rock, he uprooted trees and planted them upside down so that the roots formed the roof. By selecting trees whose roots grew out in a horizontal direction and; by planting these trees close enough - together, a crude shelter was formed. He then took mud, formed a plaster and covered over the' roots. Later the walls were made by using sticks and twigs and plastering between them. It is natural then, that he wiped his muddy hands on- his own hairy body and soon found that the mud was difficult to remove when, dry. It is due, to this discovery that we mix animal hair in 'our modern plaster to increase its strength. The use of fibrous asbestos in some refractory cements has followed this same principle.

Jan 1, 1929

By Harrison Everett Ashley

(Pittsburg Meeting, March, 1910.) Slimes are usually defined as all material passing a certain-sized sieve, which is invariably the finest sieve employed by each metallurgist in his tests; 100-mesh and 200-mesh have been taken as the limits by different writers in recent volumes of the Transactions ; 150-mesh is common practice. The reader of the first two volumes of Richards 1 is impressed by the inflexibility with which all grinding-arrangements are praised or condemned according as they make little or much slime. Until recently, one of the principal aims of the mill-man was to keep down the slimes. He was obliged to have separate apparatus for sand- and slime-treatment. The latter was sometimes puzzling and erratic. Often it was found most .economical to omit treatment of the slimes entirely, or to store them in immense basins or heaps, waiting for possible future improvements in methods of treatment. Recently, improved processes of agitation and filtration have made possible the successful extraction of values from many slimes. The tendency, when the metal is exceedingly finely disseminated, is to cut out all sand-treatment and to slime everything. These processes have been almost entirely mechanical in their conception, and it is the object of the present paper to show that certain chemical considerations may greatly hinder or assist their successful operation. It has long been a source of dissatisfaction to chemists that their analyses fail to be of much help to the clay-worker; that it is a matter of common occurrence for clays of closely identical ultimate chemical constitution to show the widest possible divergence in physical properties. * Published by permission of the Director of the U. S. Geological Survey. Ore Dressing (1903).

Aug 1, 1910

By Henry Howe

1. The purpose of the National Research Council as organized for war purposes is twofold, to stimulate those outside its own personnel to conduct researches of importance for winning the war and to carry on such researches through its personnel to a limited extent. How this is clone is explained in Section 10. "Research" is used here in a very broad sense, including, for instance, inventing and developing mechanical and physical devices. The need of this work arises from the inevitable concentration of most of the governmental war agencies on the production and transportation of war materials of. the types now adopted, as distinguished from devising new kinds of instrumentalities, such as armor, guns, aircraft, and apparatus for detecting, locating, observing, signaling, transporting, and many other military purposes. But it is important that we should devise new agencies. The war came near being won by an invention, the submarine, and its course has been affected greatly by two other inventions, tanks and aircraft. In spite of our numerical superiority victory may well be snatched from us by an invention, if we allow Germany to outstrip us in inventing. Hence the importance of the Council's work in mobilizing and organizing the services of the patriotic civilian experts throughout the country, so as to bring their powers to bear on important war problems and on inventing war devices, as an adjunct to the development work of the regular governmental bodies. 2. Status of the Council.-Though President Wilson's request caused the Council to be created by the National Academy of Sciences under its congressional charter in 1916; though his executive order of May 11, 1918, directs the heads of "Governmental departments immediately concerned" to "continue to co-operate with it in every way that may be required;" and though the Government has contributed largely to its financial support (Section 12, page 10), it is not a department of the Government but an independent research body, aiming to evolve the necessary mechanism for the novel work of systematic stimulation and guidance of research. Thus the Government, which instigated the creation of the Council, recognizes and collaborates with it, and in part supports it. The Council acts moreover as the Department of Science and Research of the Council of National Defense.

Jan 12, 1918

COLUMBIA SECTION S. S. FOWLER, Chairman., J. C. HAAS, Vice-chairman, LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY. J. F. MCCARTHY. On July 15, 16, and 17, 1918, through the good offices of Secretary Stoughton, and the courtesy of War Department officials, Columbia Section was able to secure a series of moving pictures which were presented under the auspices of the Spokane Engineering and Technical Association.. The title was "The Way Out," representing the activities of individuals who had lost an arm, a leg, or both, yet whose apparent misfortunes were made the stepping stones to advancement in various human activities. The exhibitions were given at Natatorium Park in the evening, each of the three performances being attended by 1000 per-sons. Later the films were shipped to Kellogg, Idaho, where they were shown in the principal playhouse one evening to a full house. On July 31, 1918, the Columbia Section participated in the luncheon and other entertainment in honor of Alfred D. Flinn, Secretary of the Engineering Council, who made a trip through the country to meet different classes of engineers, members of the National Societies, for whom he had a message. The entertainment was under the auspices of the Spokane Engineering and Technical Association, Mr. Peter Mogensen presiding. The luncheon was held in the Elizabethan Room, Davenport Hotel, at noon, 35 engineers being present, of whom about one-third were our members.

Jan 9, 1918

By AIME AIME

A STUDY of subsidence and ground movement in the copper and iron mines of the upper peninsula of Michigan has been made by W. R. Crane of the United States Bureau of Mines and published as Bulletin 295 of 66 pages and 49 illustrations. As a result of subsidence, the country adjacent to the mines and over- lying the mine workings in this district is often broken to such an extent as to affect its value; mine shafts and development openings are occasionally so damaged as to be rendered useless, and water can enter the workings through fractures and cave-ins. The problem is more serious in the iron-mining districts, where villages and towns not owned by the operating companies have grown up around mining operations.

Jan 1, 1929

Capital, as represented by mineral resources, is being exhausted rapidly without possibility of identical replacement. The public must be discouraged from thinking-why worry about the bank balance so long as there are plenty of blank checks? Instead of each man, woman, and child being owners of a mineral capital of $89,000 as former Secretary Ickes once stated, they are really the guardians of a mineral reserve which, when harvested, cannot be reproduced. The proper use of this material is the basis of modern civilization and military power. The best American institutions cannot be maintained or transmitted to our children unless this trust is guarded. It is unfortunate that more attention has not been focused on the fact that this country is headed for a have-not status in the family of great nations if some- thing is not done to preserve its mineral heritage. It is the privilege of the United States now to champion and implement democracy because it is industrialized and can get at its raw materials. A high price is being paid every day in mineral depletion for the privilege. No one can eat his cake and have it too. The United States still must face world-wide economic competition and, perhaps, World War III. In the final analysis all wealth comes from the ground, whether plant, animal, or mineral. Value is in-

Jan 1, 1950

The sudden and untimely death of Dr. Charles R. Van Hise, late' president of the University of Wisconsin, was one of the greatest losses, not only to the educational world and science of geology, for which he was a great leader and pathfinder, but also to the world of mining and allied interests, for which he was an adviser and helper who blazed trails and pointed out paths of development, which the practical men of englneering and industry will follow long after his death. To the general public, Dr. Van Hise stood as a great educator who conceived and wrought out a new idea in the people's university .of .a commonwealth and as a great active mind that could not be held within the bounds of education and science but, by its own bigness and broadness, was forced into the contemplation of the larger affairs of the nation. To the engineering profession, dr. Van Hise will be remembered as a tireless worker who solved some of the most complex problems in geolpgy and the development of mineral resources and recorded these findings In a form that is of lasting value to those who follow him in similar labor. In this combination of thinker and worker, educator and economic student, scientist and practical engineer, lies Dr. Van Hise's contribution to his generation. As an educator, Dr. Van Hise attained perhaps his widest recognition, for in the University of which he was president he evolved and accomplished a new idea, which caused it to be called, in 1908, by President Eliot of Harvard, "the leading State University." At the time of his death, Nov. 19, 1918, he was just completing fourteen years as president and forty-three years as student and teacher in the University. His entire life of 61 years had been devoted to his State and its University. He was the first alumnus of the University and the first Wisconsin-born citizen to become its president—and he enjoyed the longest term as president of the institution. Since his graduation from its College of Engineering in 1879, he had been constantly a member of its faculty. As Chief Justice John B. Winslow, of the Wisconsin Supreme Court said at the time of President Van Hise's death, " Wisconsin has had many able sons, men who have served their Country and their State with ais-tinguished honor in various fields of effort, but among them all none, I believe, has rendered greater service in his time than President Van Hise. The University will be his true monument, for to him, more than to any one person, we owe the present commanding position of that, great Institution." What his "new ideal of a State University" was maybe best expressed in the words which he used to outline it in his inaugural address in 1904. "I shall never be content until the beneficent influence of the University of Wisconsin reaches every family of the State. This is my ideal of a State University. When the University of Wisconsin attains this ideal, it will be the first perfect State University.... The University of Wisconsin desires to prevent that greatest of all economic losses to the State, the loss of talent. To prevent this loss of talent, the University must not only provide for those who come to Madison for instruction, but must go out to the people of the State with the knowledge which they desire and need." Hence it was said early in his administration that "the boundaries of the State are the campus fence."

Jan 1, 1920

By J. Gordon Parr, A. J. Goldak

OgdEN et al.1 and Bumps et al.2 suggested that the solubility of aluminum in a titanium extended to 30 pct.* Sagcl,3 Clark and Terry,4 Anderko et al.,5 Ence and Margolin6 and Saulnier and croutzelles,7 subsequently proposed the existence of an intermetallic compound in the region of 25 pct Al. Although Anderko et al.5 suggested that the structure of this phase, Ti3Al, was of the DO,, (Ni3Sn) type, their conclusion was based only upon the results of a powder photograph that included reflections from ? = 0 to ?= 27° (CuK),some of which were reported to be indistinct. Ence and Margolin,6 referring to a 25 pct alloy (but without indicating whether the figure referred to weight or atomic pct) stated: "The structure of Ti2Al is isomorphous with Ti3Sn DO19, as pointed out by Pietrokowsky". But the point was not proven, because Ence and Margolin did not report values of calculated intensities of Ti2Al with the DO,, structure. In fact, the observed intensities they reported are in poor agreement with the values we calculate for DO19 (see Table I). Saulnier and croutzelle7 concluded, on the basis of electron micrography and microdiffraction studies, that the structure of the 25 pct A1 alloy was ordered hexagonal. Our purpose has been to unequivocally determine the Ti3Al structure. Alloys containing 25 pct Al were prepared from iodide titanium and spectrographic standard aluminum by levitation melting. The levitation chamber was evacuated to 10-6 mm Hg before filling with 99.999 + pct A. After casting, the alloy was chilled to liquid air temperature and crushed to -200 mesh in a percussion mortar. The powder, wrapped in molybdenum foil, was annealed (by induction heating) at 1000 "C for 2 hr in the argon atmosphere of the levitation chamber. No sublimate was seen on the foil or elsewhere, and therefore the assumption is

Jan 1, 1962

By Walter C. Holmes

IN the recently published book entitled "Man in a Chemical World," by A. Cressy Morrison, the several pages discussing explosives were included in the chapter on "Serving Industry." Such a classification is entirely correct, as blasting explosives function only as a tool for accomplishing certain useful work, a tool which is completely destroyed in one use. Explosives are so important to industry and to modern society, in fact, that it seems impossible to imagine the existence of civilized nations without access to commercial explosives as ready servants. Two main types of explosives are now in use, the low-velocity or deflagrating type, such as black powder, which is adapted for use in coal mining and other applications where a slow, heaving effect is desired, and high explosives of the dynamite type,

Jan 1, 1938

By Walter Bradley

MINING by hydraulic process of the important gold-bearing gravels of the Sacramento Valley in the basins of the Yuba, Bear and American rivers began in 1853, and continued at an ever-increasing rate for 30 years. In its most active days it reached an annual production of $15,000,000, and averaged $10,000,000 per year over the 30 years. During that period no provisions were made to prevent the debris from being dis-charged into the water courses, and ultimately large quantities of silt, sand and gravel were washed down to the lower valleys; filling channels, causing overflow of agricultural lands and difficulty in maintaining navigable depths in the Sacramento River. Agitation and suits filed because of these damages finally resulted in the injunction decision of Judge L. B. Sawyer,1 in the U.S. Circuit Court, Jan. 23, 1884, which closed down practically all hydraulic mining operations not having means to restrain their debris. In 1893 (approved March 1, 1893), Congress passed the act introduced by Representative Anthony Caminetti, of California, creating the California Debris Com-mission, composed of three officers assigned from the Engineer Corps of the U.S. Army, and since that time it has been legal and possible within the drainage systems of Sacramento and San Joaquin rivers to conduct hydraulic mining of gold-bearing gravels behind dams built under this commission's permit and supervision. In the watersheds of the Trinity and Klamath rivers, which flow directly to the Pacific Ocean and do not affect navigation or agriculture, operating permits from the California Debris Commission are not required. There is a measure of restriction there, however,. through what is known as the Trinity and Klamath River Fish and Game Dis-trict. Chap. 215, Stat. 1931, in order to secure relatively clear water for the fishing season, provides that between July 15 and October 15 each year there must not be discharged into these rivers debris that will cause a turbidity greater than a content of 50 parts per million in the

Jan 1, 1936