Search Documents

By S. M. Marshall, A. C. Richardson, H. Y. Yancey

A year ago, Marshall and Bird presented a paper in which a new method of measuring the agglutinating power of coal was described.' The procedure used was to determine the strength of a button containing 10 parts sand and one part coal, formed by carbonizing the mixture in a crucible in an electric furnace. The result of the determination was reported as the total weight in grams required to bring about complete destruction of the button. Correlations were shown between the agglutinating value and some of the characteristics of the different coals that were investigated. This agglutinating test has been in use fairly continuously during the past five years for coals of widely differing coking qualities, and it has shown reasonably concordant results accurate enough for commercial use, although there are many features of the test which should have further scientific study. During the past year a study has been made of some coals of low coking strengths, and incidental to the main investigation some data which appear to be of interest and value were obtained on the loss in agglutinating power caused by exposure to the air. Three coals were investigated, all of which were of the Tertiary age; two were from one field in Asia, and one from a field in the United States. The three were similar, as shown by the proximate and ultimate analyses in Table 1 (moisture-free basis). Coals SA and RA generally contain about 5 per cent. moisture and coal P about 3.5 per cent. moisture on the as-received basis. The large difference in the ash contents of the coals, amounting to practically 10 per cent. between SA and RA, and P, makes difficult a direct comparison of their qualities. In the second section of Table 1 the figures have been put upon an ash-free basis., This table shows that these coals are closely alike. The ultimate analyses are almost identical except for the higher nitrogen content of

Jan 1, 1930

By S. R. Gilbert, B. W. Burdett, L. B. Hales

INTRODUCTION Grinding control is currently the most publicized control subject in the minerals industry. Flotation control and crushing control have not as yet received the widespread attention that grinding control has. The primary reasons for this center around the high capital costs of grinding equipment and the fact that grinding mills are extremely energy inefficient. In a typical copper concentrator the energy requirements to produce refined copper are: (1) [Total Energy Distribution (Kw-hr/yr)% Mining4.93 x 10817.3 Mineral Processing9.63 x 10833.8 Smelting and Refining13.9 x 10848.9] One-third of the total energy used for copper production is for mineral processing. A breakdown of this energy into process steps yields the following: [Total Energy Distribution (Kw-hr/yr)% Crushing and Grinding 7.16 x 108 73.8 Flotation 0.76 x 108 7.8 Materials Handling1.78 x 10818.4] It is apparent that comminution operations consume the largest proportion of the energy for processing and as such become major targets for improvements in efficiency. Unfortunately, size reduction operations are extremely inefficient. Efficiency calculations for grinding range from less than 0.1% to about 5% depending on the evaluation criteria. Because of these facts, grinding control has been and will continue to be the focus of major process control efforts. OBJECTIVES AND BENEFITS All benefits achieved as the result of grinding control are derived from modifying physical parameters which improve the efficiency of the grinding mill. These parameters include:

Jan 1, 1982

By C. A. Heiland

FOR the past three years, the senior writer has carried out, with inter-ruptions, a series of investigations into the characteristics of prospecting seismographs of a wide variety of construction. Early in 1932, a com-plete equipment was developed for both refraction and reflection observa-tions; its first function being, however, the application in reflection shooting. The performance of the equipment proved to be highly satis-factory in a series of field tests' which were carried out by the junior writer, whose services were loaned to the Colorado School of Mines by courtesy of the Plains Exploration Co. in Denver. The various problems that were encountered in the construction of the equipment, in its application in the field, and in the interpretation of the results, are fully treated in Publication 47 of the Department of Geophysics of the Colorado School of Mines. Its first part deals with the various problems encountered in the design of the instruments, and presents a discussion of such topics as the free and forced oscillations of damped and undamped mechanical seismographs, the action of oscil-lographic recording instruments and amplifiers, the characteristics of electromagnetic seismographs, and the requirements of damping, natural frequencies and static magnification for the pickups, amplifiers and oscillographs used in refraction and reflection seismographs. Further-more, a detailed discussion of the various methods of static and dynamic tests of seismic receivers, and a description of the reflection equipment developed at the School of Mines is presented. Unfortunately, a delay has occurred in the publication of the first part of this investigation concerning the instrument problems. There-fore, the second part, dealing with the field problems, is herewith pre-sented first.

Jan 1, 1933

References are in all cases to the earliest known editions. In the few cases where the first edition has been unavailable for consultation, the particular one studied is indicated. English translations are included when known, but not others. [ ]

Jan 1, 1942

By Frank R. Van Horn

It is customary to ascribe two general modes of occurrence to natural gas, namely, shale gas which, as the name indicates, is found in shale, and reservoir gas, which occurs in sandstone, conglomerate and dolomitic limestone. Both of these types are found in the Cleveland district. The shale gas has been produced on a small scale for a long period of years, probably dating back as far as 1883. Shale gas is a low-pressure gas, small in volume with variable pressure, and is limited to no definite horizon. It is generally independent of oil, may last for a long time, and is not dependent to any great extent on the structure of the rocks. There are many such wells in the district which range from 400 to 1,840 ft. in depth, although most have been completed at about 800 ft. This indicates that the wells pass through the Cleveland and Chagrin shales into the Huron or Portage shale of the Upper Devonian. During the last 2 years great interest has developed in a deeper-seated reservoir gas. What is commonly called reservoir gas is generally a high-pressure gas occurring in large volume at a definite horizon. Oil may, or may not, be associated with the gas, and in most regions in which reservoir gas is found, the geological structure is of great importance. This type of gas occurs in all large fields such as those of West Virginia which have been supplying Cleveland until the recent discovery of local gas at great depths in commercial amounts. Historical Outline The oldest well producing reservoir gas in the district was drilled in 1886 in Newburg for what was then known as the Cleveland Rolling Mill Co. This well was 3,000 ft. deep, and was thought to have reached the "Clinton" formation. Two "sands" showing small amounts of oil were recorded in the Niagara limestone at depths of 2,658 and 2,686 ft. This is about the horizon of the so-called Newburg sand which has proved to be of some importance as a source of gas and oil by recent drilling operations. The rock pressure was reported to be 400 to 500 lb. per square inch, but since the volume was only 14,000 to 16,000 cu. ft. daily, the well was not only considered unsuccessful but was thought to prove the absence of high-pressure gas in commercial quantities in the Cleveland district.

Jan 1, 1917

Secondary minerals are the result of a process of concentration and enrichment and are commonly richer than the primary minerals of the same deposit. Secondary ores that contain abundant sulphides are commonly distinguishable in the field from primary ores; this distinction is more difficult with ores that carry a small quantity only of sulphide minerals, and microscopical examination of the ore in thin section is advisable in all doubtful cases. It is frequently difficult, and in some cases impossible, to determine the primary or secondary character of quartzose gold ores. The safest guide is the presence or absence of gaseous or fluid inclusions in association with the ore minerals; such primary association coupled with a lack of traces of oxidation is indicative of primary origin. Any ore that carries traces of oxidation, such as iron stains, endritic oxides of manganese, kaolin and so forth must be considered to have been acted upon by surface agencies, and secondary enrichment must be suspected. Further examination, however, may indicate that the contained value is primary, and, therefore, persistent in its vertical distribution. The manner of occurrence of secondary minerals is frequently characteristic; secondary minerals, being due to the action of surface waters, are commonly found in cracks through earlier minerals, or as crusts lining vugs or surrounding nucleal masses, or in general, in some distribution later than and not conforming to the arrangement of the primary minerals. Secondary sulphides are often found as soft black pulverulent masses or coatings, although they frequently occur well crystallized or as

Jan 1, 1932

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack-poles of New York, from drawings, considerably modified, of Combes's theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet-for indeed the instrument is easier levelled, and, more-over, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity ; on the other hand, however, that correction

Jan 1, 1873

By Francis L. Vinton

THE eccentric theodolite I exhibit is one constructed by the Stack poles of New York, from drawings, considerably modified, of Combes's theodolite. The telescope is on one side of the horizontal limb, and the vertical circle is opposite to the telescope ; thus they nearly balance each other, making already the construction lighter than in the instrument of Combes, where the telescope and vertical circle are together on the same side, and are both balanced by a considerable weight. The instrument stands upon three levelling screws or feet, an improvement upon the old or general style of mounting a transit on four feet for indeed the instrument is easier levelled, and, moreover, stands more stable on three than on four points of support. The general advantage of an eccentric theodolite is evident, namely, that it can measure Any and all vertical angles, from 0 to 360, without being interfered with by the horizontal limb as is the transit; besides this advantage, it needs no preparatory adjustment or correction for eccentricity; on the other hand, however, that correction

By Yang Tsang Woo

The method of making coke that has been adopted at the Kaiping and other collieries in northern China resembles, to some extent, the familiar bee-hive oven process of the United States, except that a kiln with permanent sides is used instead of a closed oven, and the products of combustion are drawn off at the bottom. In building coke-kilns in China, two circular holes, 8 ft. 6 in. in diameter at the bottom and 13 ft. in diameter at the top, are excavated in the ground, and connected at the bottom by a flue, as shown in Figs. 1 and 2. The sides and bottom of the kiln are lined with fire-bricks, and covered with a lager of fireclay, and a rectangular opening, 6 in. by 8 in., connects the bottom of each kiln with the main flue. Around the edge of the hole, and overlapping the lining, is a wall of fire-brick extending 2 ft. 6 in. above the level of the ground. An open space 5 ft. wide is left in this wall, through which the coal is carried into the kiln and the resultant coke removed. This space, of course, is bricked up during the time that the coking-operation is being carried on. The wall is pierced with nine flue-openings uniformly placed around the circumference, each interverliilg space in the wall being strengthened with a brick buttress, as is shown in Figs. 2 and 4. The floor of the kiln, as well as the main flue, is lined with fire-brick. Before charging the coal, it is first placed in shallow bamboo sieves, 2 ft. in diameter, and immersed in a trough 10 ft. long, and 3 ft. wide, fed with pit-water, in which it is washed by hand. Fig. 3 shows the manner in which the washing is done. From 25 tons of good "dust" coal, 22.5 tons of washed coal are obtained. When ready to charge the coal into the kiln, a temporary cone-shaped flue of fire-wood and lump coal is first built to a

Jan 1, 1906

By R. P. E. Hermsdorf

THE electrolytic refining of metals for the removal of undesirable impurities has become a recognized necessity in the nonferrous field. Copper, lead, zinc, nickel, silver and gold have been produced in this manner for years. The United States Metals Refining Co., realizing that considerable quantities of lead and tin could be made available to the trade if a satisfactory method of purification of these metals could be established, decided to investigate the possibilities of electrolytic solder. In cooperation with Dr. Edward F. Kern, of the School of Mines at Columbia University, the company developed a process of electrolytic refining of lead-tin alloys using a tin-lead fluosilicate electrolyte. A pilot plant was installed in November, 1927, and the commercial unit was put in October, 1929. Since that time thousands of tons of electrolytic solder have been produced in this plant and consumed by all branches of industry that use solder.

Jan 1, 1936

The members of the Institute living in the lower Mississippi Valley, I extend a hearty and cordial invitation to their fellow-members to meet with them nest October, in St. Louis. They believe that it will be a meeting of singular interest, inasmuch as the district in question can show in active production almost all of the more useful metals and non-metals. Perhaps too few know that the Southeast Missouri District, about 80 miles south of St,. Louis, and to which a special trip is planned, is the largest lead district in the world. It was that before-the European war, and, now that the production of lead has greatly increased abroad, and has correspondingly increased in the United States, this is one of the most interesting of all lend districts. In 1913, the production of the world was 1,270,000 tons, the last world figures obtainable. In that same year the production of the United States

Jan 5, 1917

By William Phillips

THE earliest mention of the sulphur deposits in what is now Culberson County, Texas, seems to be contained in "Explorations and Surveys for a Railroad Route from the Mississippi River to the Pacific Ocean, United States War Department, 1853-54." Captain John Pope (he was not commissioned Captain until 1856) had charge of one of the divisions of the Survey. In his report on the geology of the route, William P. Blake noted the analysis of a greenish earthy powder from the bed of Delaware Creek, at the springs, which contained 18.28 per cent. of free sulphur. The report states: "From the chemical examination of the waters of the spring, by Dr. Booth, it appears that chloride of sodium is the principal solid ingredient, but considerable quantities of sulphide of sodium are present. * * * * * The waters from the springs examined by Dr. Booth were alkaline, but it is possible that some of the springs are acid; and in this case the precipitation of sulphur would ensue on the mixture of the acid waters with those charged with alkaline sulphurets and the origin of the deposits of sulphur would he thus explained." This is the first reference to the existence of sulphur in that region, the first mention of the character of the water found there and the first suggestion as to the' origin of the deposits. The possibility of the existence of acid waters was confirmed by E. M. Skeats, nearly 50 years later.1 In this publication, Skeats says that the water from the sulphur deposits in Section 11, Block 114,, Township 5, contains 79.08 grains of free sulphuric acid per gallon. This locality is about 13 miles (21 km.) south of Delaware Creek and about 35-miles (56 km.) east of the Delaware Springs. The next published reference to the existence of sulphur in Trans-Pecos Texas is in the First. Annual Report of the Geological Survey of Texas, 1889, page 226, where W. H. von Streeruwitz mentions that sulphur is found in that region, but gives no further information. In the

Jan 9, 1917

By H. A. Koch, R. L. Slobod

This paper discusses a new oil recovery process called the "miscible slug process." This process involves the injection of propane or LPG into the reservoir prior to gas injection. The operating conditions are maintained so that the slug is miscible with both the reservoir oil and the injected gas phase. Thus, a miscible phase displacement is achieved, and high recoveries are obtained from the area of the reservoir contacted. The most striking discovery of the laboratory study which included displacements from cores up to 123 ft in length was that relatively small slugs of LPG are effective over reservoir distances in the miscible displacement of oil. This makes possible the commercial application of the process. The important factors controlling the size of the slug are: (I) reservoir length, (2) reservoir fluid composition, and (3) reservoir pressure at the displacement front. Of lesser importance are the effects of injection rate and porous medium type. Questions which have not been completely answered deal with the effects of gravity and reservoir inhomogeneities on the process. INTRODUCTION One of the major problems facing the oil industry today is recovery of the large fraction of the discovered oil which will remain unrecovered unless some new processes are found. Water flooding has been one successful method used to increase recovery over natural depletion. But even successful water floods may leave 25 to 40 per cent of the pore space filled with residual oil. Recently a process which involves the use of thermal energy has been reported1,'*' which may prove useful in increasing recovery from shallow reservoirs containing highly viscous crudes. This paper deals with a new oil recovery process involving use of miscible phases to displace the oil from the reservoir. Miscible phase displacement oil has been an intriguing idea because the elimination of capillary effects in the reservoir leads to 100 per cent recovery in the areas contacted by the miscible displacing phase. The big deterrent in the past to the practice of miscible phase displacement has been the high cost involved in using large volumes of solvent in the process. The use of high pressure gas to achieve a miscible phase displacement of reservoir oil has been reported4,5 as one economically feasible method. However, this process calls for the maintenance of pressures above 3,000 psi at the dis-placement front. The process described in this paper is not restricted to high reservoir pressures; the only qualification being that the slug of material which is injected into the reservoir must be miscible with both the displaced oil 2nd the displacing phase. Two such cases are the use of an alcohol slug followed by water to achieve a mis-cable water flood, and the use of a low boiling hydrocarbon slug such as propane followed by gas to achieve a miscible gas drive. This paper will deal specifically with the propane dug process. This process will obtain a miscible phase displacement at pressures as low as about 1,200 psi at a reservoir temperature 01 150°F. The process is very simple. The propane displaces oil completely at one front because it is miscible with the oil, and gas displaces the propane completely at a second or trailing front because it is miscible with the propane. A small band of propane should thus remain wedged between the gas and oil phases. This idea has been called the "miscible slug process."6 Unfortunately, the propane slug will become diluted as it flows through the reservoir. This results from a mixing action since the fluids flow through a complex reservoir porous medium rather than simple capillaries. Fig. 1 diagrams a miscible slug displacement. The effects of some of

Jan 1, 1958

By Claudio Gutiérrez

The action of quebracho in the selective flotation of fluorite and calcite has been studied. It has been found that the unavoidable ions produced by dissolution of these minerals can precipitate calcium oleate which profoundly influences the adsorption of oleate. The depressing action of quebracho is due, at least partly, to a decrease of the oleate adsorption. The depression of flourite flotation by quebracho in the presence of calcium is due to the fact that precipitated calcium oleate can become only physisorbed, its adsorption being strongly prevented by quebracho. It is concluded that adsorption experiments with flourite must be conducted with a flotation-size mineral, which has a lower dissolution rate than when finely ground.

Jan 1, 1980

By Herbert Haas

GEORGE W. HAWKINS, Tucson, Ariz. (communication to the Secretary*).-The paper by Mr. Haas will no doubt be followed with considerable interest, as it covers the power-plant problem in quite a comprehensive way, including not only the usual operating costs but also the fixed charges on the investment, and for load factors ranging all the way from 25 to 100 per cent. and fuel oil ranging from $1.25 to $2 per barrel. The very fact, however, that his paper does cover such a wide range of conditions, makes it the more imperative that any conclusion drawn from his analysis be very carefully considered for any specific case, for in making such analysis the type of prime mover and size must be selected for some one condition which might not be the proper selection had some other condition been assumed as the basic one, resulting in an unfavorable comparison under all conditions except that condition assumed. From the reasons given by the author for his selection of the large turbine units, it is evident he had in mind very high load factors, ranging

Jan 12, 1916

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd.: (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the, St. Eugene Concentrator, Moyie, B. C., and (3) the. Tadanac (Customs) Concentrator,Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals -lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a FIG. 1.-THE SULLIVAN CONCENTRATOR, CHAPMAN CAMP, B. C. (NEAR KIMBERLEY, B. C.). low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential-flotation.

Jan 1, 1927

By Michael A. Toole, O&apos

INTRODUCTION The tremendous capital investment required to produce a low grade ore deposit demands a reliable answer to the question: "How much does it cost to drill a well to produce the uranium that geologists have indicated is there in the ground?" However, you will find the answers given will be many and varied, depending on whether they come from the operating company, the drilling contractor, a geologist, a reservoir engineer, purchasing agent, or whoever. Each generally considers only a limited area of the total operation. The operating company usually depends upon the drilling contractors, service companies, and consultants to supply expertise. Because it is often difficult to see the "whole picture" or even to agree upon what the "whole picture" is, planning a well program and its costs is often done piecemeal. Frequently, costs "saved" in one area of the program are needlessly spent in another, because the effect of one area upon the other was overlooked. Since the drilling fluid is such an influential part of the drilling program, it should be given utmost consideration when planning the overall program. As W. D. Lacabanne wrote in 1954: "The drilling fluid system is understandably called the heart of the rotary oil drilling rig. Any other type of rotary rig.... should benefit by the incorporation of mud fluids in the drilling scheme." And G. R. Gray mentions that "The driller recognizes the drilling fluid as one of the useful tools available to solve drilling problems." However, in minerals drilling, only in recent years has the drilling fluid been considered as more than a tool to get through special problem areas. Although there are many similarities between drilling for oil and gas and drilling for minerals, the differences in the drilling equipment used justifies designing specific fluids for the minerals drilling industry. NL Baroid/NL Industries, Inc. has been a leader in introducing such fluids and in providing technical know-how to the minerals drilling industry. The purpose of this paper is: (1) to discuss the selection of drilling fluids to meet specific drilling conditions during both exploration and production and (2) to show the interrelationship among factors present in the exploration and production phases that influence total well costs. DRILLING FLUIDS FOR DRILLING PROBLEMS The drilling fluid is a tool that can be used to improve drilling performance by improving hole cutting, cleaning, stability, and formation productivity. Properly formulated and maintained drilling fluids enable the drilling operation to be carried out with increased efficiency and lower total (overall) costs. However, it should be noted that not all drilling problems can be solved by even the most carefully prepared and maintained drilling fluids. Of the many possible drilling problems encountered in a well before reaching target depth, this paper will discuss only those most likely to be present in the shallow [61 to 610 m (200 to 2000 ft)] drilling operations in South Texas. LOST CIRCULATION Loss of circulation is the most common problem encountered in drilling. Because the losses occur under varied conditions, it is often difficult to determine the exact causes. "Lost circulation" or "lost returns" means the partial or complete loss of drilling fluid to voids in the formation. "Loss of water" while drilling with water may take place into any permeable section and should be distinguished from "water loss" or filtration of fluid through the filter cake of mud solids laid down on a permeable formation. "Loss of water" can frequently be stopped by the addition of colloidal sized clay particles such as high yield bentonites, whereas "water loss" may be controlled with organic polymers. Subsurface conditions that lead to loss of circulation can be classified as: (1) natural fractures, (2) induced fractures, (3) unconsolidated or highly permeable formations (loose gravel), and (4) cavernous formations (crevices and channels). Loss of circulation may occur whenever the borehole pressure exceeds the formation pressure. The greater the differential pressure, the more likely it is that circulation may be lost. To stop loss of whole mud, voids must be bridged so that a filter cake can be laid down on the permeable section. The plugging material must be of the proper size and shape to offer greater resistance to the fluid flow around it than the flow up the annulus. A plugging composition that satisfies these requirements may not be able to be handled by the small rig pump available.

Jan 1, 1979

By Jacob T. Wainwright

AS a means for increasing the efficiency in modern blast-furnaces by supplying to them blast of a much higher temperature than is now possible, the writer offers as a suggestion a modification in the construction of regenerative hot-blast stoves. Stated briefly, the plan proposed is to pre-heat both the gas and the air for its combustion in a manner similar to that generally adopted in Siemens openhearth furnaces. After thus carrying the temperature of the stove to a point much higher than that common in hot-hlast stoves, the cold blast passes through it. Without entering into the details relating to the reversing valves and the system of flues, the general plan may be outlined as follows, referring to the accompanying drawings: The valves are so placed in heating up the stove that the blast-furnace gas enters at B, Fig. 1, and the cold air for combustion at A. Ascending in flues, F and E, respectively, combustible gas and air meet and mix in the combustion-chamber, I. Flowing through K, they descend through the flues, G and H, escaping through the chimney. In this manner the walls of the combustion. chambers, I and L, are highly heated, and the right-hand side of the stove is carried to a higher temperature. By reversing the valves, blast-furnace gas enters at C and cold air for combustion at D. Both are pre-heated in their ascent through the flues, G and H. They burn in the combustion-chamber, L, and the hot gases of combustion, flowing through K, I, E and F to A and B, heat the left-hand side of the stove. In this manner the stove is carried to a temperature greater than that of those now generally in use, in which air and gas are burned without preliminary pre-heating. In the plan proposed, that side of the stove will, of course, be relatively cooler through which cold air and furnace-gas last passed in its ascent to its combustion-chamber. After having sufficiently heated the stove in the manner outlined, the cold blast is admitted through all the flues, A, B, C and D. It ascends through the highly-heated regenerative material to the chambers at the top and descends through the flue, P, Fig. 2 (dotted

Jan 1, 1889