Search Documents

By J. H. Westbrook

UNTIL very recently the development of high temperature alloys has been strictly empirical. It is, in fact, a great tribute to the intuition, perseverance, and industry of the practicing metallurgists of this country and abroad that the amazing increases in gas turbine service temperature over the past 15 years have been achieved with so little fundamental knowledge. The result of this development has been the realization of successful but highly complex alloys possessing five, six, or more alloying elements and correspondingly complex microstructures. Within the last few years, considerable effort has been devoted to the identification of the secondary phases in these alloys and to the correlation of the presence or absence of such phases with alloy properties. Little attention, however, has been given the problem of identification of the mechanism (s) by which such phases enhance the properties of the alloy and especially to the assessment of the particular properties of the secondary phase (either in- trinsic or relative to the matrix phase) which are basically responsible for the improvement. Conceivable mechanisms which might apply include dispersion hardening and precipitation hardening. In both cases geometrical factors—particle size, dispersion, volume fraction, etc.—and agglomeration re-

Jan 1, 1958

By H. H. Power, C. H. Pishny

When an oil operator becomes a party to a proration agreement he may wonder, with good cause, whether production prorated .today is merely deferred until tomorrow or whether oil might be lost. Various types of evidence obtained from production records when studied quantitatively are of great assistance in arriving at definite conclusions. A study of individual examples cited in this paper leads towards some solution of the problem, particularly when they are considered in the aggregate. Many production curves on various pay horizons were studied. A disappointingly large number of these were of contributory value, but inconclusive. However, there were enough curves of similar type from the Wilcox sand at Earlsboro, Bowlegs, Seminole City, the Cromwell horizon at Little River, and the Simpson dolomite at Valley Center, Kansas, from which reasonably definite conclusions were drawn. Assuming that deferred production is later made up with no increase in ultimate recovery, a curve (Fig. 1) shows the normal flowing and pumping life of a composite well, contructed by the family curve method. The initial production of the well shown is 1700 bbl. daily and the allowed production is 25 per cent. On this basis the average daily allowed rate for the first month is 425 bb1., or the area BCDE, which is equivalent to the area AFDG under the normal decline curve. The potential production for the second month is 1500 bbl. and the allowed production 375 bbl. daily. By this procedure a potential curve for each succeeding month is obtained (points A, H, I, J and K). If the well is opened it should produce somewhere near its potential curve for a short period and then decline at a more rapid rate than the potential curve. This theoretical analysis is basic. Actual examples exhibiting all points raised by the ideal curve are rare. Proration in the Mid-Continent area has been effected mostly by leases rather than by individual wells; hence a well may produce any

Jan 1, 1931

By Leonard Logan

Production control in the petroleum industry may be discussed under three general heads: engineering, legal, and economic. Though the problems that fall under the respective heads of engineering, law, and economics are separate, they are dependent and interrelated. The present study will deal with the economic phases of production control and only incidentally with the legal phases as they affect the economics of the problem. No one of these forms of control is more important than the others. The engineers have performed their service well, and although there are many problems of engineering control yet to be solved, they are not pressing. Legal control is a problem for the legislatures and the courts to solve. The petroleum industry is such a comparatively young industry and the legal problems are of such recent origin that the courts have not yet been called on to settle all the issues and the legislatures still have before them bills concerned with the regulation of the industry. Economic control of production in the petroleum industry is a highly desirable goal but it has not yet been completely achieved. Since the first commercial well was drilled in 1859, there have been recurring periods of overproduction. (Over- production will be used here to describe a condition wherein so much crude oil is available that a satisfactory and reasonable price is not received for the product.) The production of oil in 1859 approximated only 2000 barrels. In the following year production jumped to 500,000 barrels, thus bringing into

Jan 1, 1932

By John V. Beall, William F. Haddon

A long the mighty Andean Cordillera, there is splendor beyond imagination-in the natural beauty of the mountains and in daring engineering and lavish investment in the mines. This is the story of the great copper mines of Chile and Peru. Each mine has a special quality which has tested the physical and spiritual resources of the founder. In the early days of the older mines, the mining engineer of song and story was more the rule than the exception. He was physically tough, ingenious and a leader of men. In the current political and social environment of Chile and Peru, the foreign contract mining engineer is still needed; but he must be a different type of man. To John J. Selters at Cerro's Rio Blanco, the principal ingredient is still "toughness," but it is "toughness of mind" that is needed. "He probably should be a teacher." The copper mines are not new. They were, almost without exception, worked by Indians (La Exotica might prove the rule), and later by the intrepid Spaniards. Modern mining began after the turn of the century. In Chile, the first of the big ones was the Braden Copper Co. founded on the El Teniente deposit. This development was followed by Chile Exploration Co. at Chuquicamata and Andes Copper at Potrerillos. These properties have been developed over the years by vast expenditures of money and a monumental amount of labor. None was free of technical problems-metallurgy at Chuqui, marginal grade of the old mine at Andes, avalanches and the great fire at El Teniente. The evolution which has brought the established mines of Chile, and the new ones coming on stream, to their present state of development is in reality the work of wonders of input-money, engineering and responsible management in an atmosphere of political stability. Without any one of these, the result would have been failure.

Jan 11, 1969

By Paul M. Tyler

MUCH information concerning pegmatites which was thought to be true a few years ago has been proved false, and what is now actually known about some pegmatites is not true of many others. The erratic and seemingly unpredictable structure and variable composition of this class of mineral deposits has been widely emphasized. Even parts of the same pegmatite body exhibit marked differences in texture, mineral composition, width, and attitude. Constructive geological thinking in respect to pegmatites now aims to establish general laws rather than to stress the confusing diversity of features having no special economic significance.

Jan 9, 1953

By J. K. Buehler

With the rapid acceleration of the cost of shovel dippers and major standard shovel clipper rebuild components, maintenance management at Kennecott Copper Corp.'s Bingham Canyon mine initiated a dipper maintenance and rebuild program. The program focused on extending the service life of the shovel dipper, reducing field labor in maintaining dippers, and lowering shovel dipper rebuild costs. While comprehensive evaluation of the program is still underway, preliminary benefits of the program indicate: •Reduced field ,gelding for shovel dipper field maintenance, •Fewer dipper rebuild units entering the shop, and •Reduced dipper rebuild costs per unit.

Jan 1, 1979

By William O. Hotchkiss

IN COMMON with every other good citizen I long for conditions that will make perpetual peace a reality throughout the world. I have studied the statements of our public men relating to what we must do to bring this about after this war is over. In most of these I find one common error. They always build their plans on the unstated, subconsciously accepted premise that there can be such a thing as an ideal nation whose citizens are possessed of infinite wisdom and actuated only by motives that are above reproach. This heavenly vision fails to correspond with the facts. We wish it could be true but we are forced sadly to admit that the human beings that will live here after this war is over are going to be much like the fallible race that has occupied our planet for the past centuries.

Jan 1, 1943

By R. W. Snyder, W. H. Guilinger, B. S. Gottfried

Two numerical methods are presented JOT solving the equations Jor one-dimensional, multiphase /low in porous media. The case oF variable physical properties is included in the Formulation, although gravity and capillarity are ignored. Both methods are analyzed mathematically, resulting in upper and lower bounds for the ratio of time step to mesh spacing. The methods are applied to two- and three-phase waterflooding problems in laboratory-size cores, and resulting saturation and pressure distributions and production histories are presented graphically. Results oJ the tuo-phase flow problem are in agreement with the predictions of the Buckley-Leuerett theory. Several three-phase flow problems are presented which consider variations in the water injection rate and changes in the initial oil-and ujater-saturation distributions. The results are different physically from the two- phase case; however, it is shown that the Buckley-Lez~erett theory can accurately predict fluid interlace velocities and displacing-fluid frontal snturations for three-phase flow, providing the correct assumptions are made. The above solutions are used as a basis JOT et~aluuting the numerical methods with respect to machine time requirements and allowable time step for a fixed mesh spacing. INTRODUCTION Considerable progress has been made in recent years in obtaining numerical solutions of the equations for two-phase flow in porous media. Douglas, Blair and Wagner2and McEwenll present different methods for solving the one-dimensional case for incompressible fluids with capillarity (the former using finite differences, the latter with an approach based upon characteristics). Fayers and Sheldon4 and Hovanesian and Fayers8 have extended these studies to include the effects of gravity. West, Garvin and Sheldon, l4 in a pioneer paper, treat linear and radial systems with both capillarity and gravity and they also include the effects of compressibility. Douglas, Peaceman and Rachford3 consider two-dimensional, two-phase, in compressible flow with gravity and capillarity and Blair and Peaceman1 have extended this method to allow for compressible fluids. No one, however, has examined the case of three-phase flow, even for the relatively simple case of one-dimensional flow of incompressible fluids in the absence of gravity and capillarity. In obtaining a numerical technique for simulating forward in situ combustion laboratory experiments, Gottfried5 has developed a method for solving the one-dimensional, compressible flow equations with any number of flowing phases. Gravity and capillarity are not included in the formulation. The method has been used successfully, however, for two- and three-phase problems in a variable-temperature field with sources and sinks. This paper examines the algorithm of Gottfried more critically. Two numerical methods are presented for solving the one-dimensional, multi-phase flow equations with variable physical properties. Both methods are analyzed mathematically, and are used to simulate two- and three-phase waterflooding problems. The numerical solutions are then taken as a basis for comparing the utility of the methods.

Jan 1, 1967

By B. C. Craft

The principal events in the oil and gas operations for Louisiana during 1933 have been the rapid development of the Converse field in Sabine Parish, the discovery of three new salt domes, one in North Louisiana and two in South Louisiana, increased development in the Iowa field on the Calcasieu-Jefferson Davis Parish line, and extensive geophysical operations over a wide territory. Other miscellaneous events worthy of mention are the continued leasing of prospective oil lands over a wide area, extension of production at the East Hackberry field, Cameron Parish, discovery of deep sands at Caillou Island, Terrebonne Parish, and the completion of several important wildcats. Despite proration, oil production showed a substantial increase during 1933. The total output for this area was 25,599,802 bbl. as compared with 22,507,387 bbl. during 1932. North Louisiana There were 111 oil wells and 47 gas wells completed in North Louisiana during 1933 as compared with 109 oil wells and 33 gas wells during 1932. North Louisiana oil production decreased approximately 692,625 bbl. in 1933 from its 1932 figure. The normal decline in the old fields was partly offset by increased production at the Zwolle and Converse fields in Sabine Parish. Acid treatment of wells in the Zwolle, Converse and Monroe fields was highly successful. The method of application has been described by H. K. Shearer, Geologist, Pelican Natural Gas Co., as fo1lows:l With tubing in the hole and standing valve removed, the casing is filled with oil to the surface. The limestone solvent is pumped in through the tubing, at the same time bleeding off enough oil from the casinghead to equal the volume contained in the tubing plus the volume of open hole to be treated. The amount of solvent used in most of the wells treated was 1000 gal., which is enough to dissolve about 11 cu. ft. of chalk or limestone. After the computed amount of oil is bled off, the casinghead is closed and the remainder of the solvent is pumped in at whatever pressure is necessary to force it into the oil-producing horizon. The solvent is followed up with enough oil to

Jan 1, 1934

By J. B. Newsom

SAFER, cheaper, and faster sinking of mine openings seems to have been realized with the completion of a borehole 5 ½ ft. in diameter and 1208 ft. deep, in Minnesota, during 1938. Moreover, as the opening is to be used solely for ventilation, its circular cross section, smooth walls and freedom from fire hazard recommend it in comparison with the usual timbered shafts of rectilinear cross section. It should be pointed out that a drill hole sunk without the use of explosives frequently will stand open without support, whereas a shaft sunk by standard procedure using dynamite usually must be timbered because of the wall-shattering effect of explosives. The saving in maintenance resulting from the elimination of timber is obvious. The work was done by Pickands Mather & Co. at its Zenith mine, Ely, Minn. This company wanted a ventilation opening capable of delivering 50,000 cu. ft. of air per minute to the fourteenth level, 1200 ft. below the surface. While several general articles1-3 have described the method used, detailed time and performance records have not been presented before. Moreover, with a method as new as this, it is important to compare the results attained under widely varying conditions. Among the new conditions faced at Ely were some extremely hard rock, a series of vertical fractures, seepage water, and some long stretches of sound rock which, combined with excellent equipment, gave a chance to operate without unusual delays. Developments in boring large holes have generally taken the obvious course of increasing the size of the equipment, a line of attack that has resulted in putting down 3-ft. diameter holes at damsites for studying the foundations4 and in drilling ventilation openings between levels at Butte. 5 Such drills operate from the collar of the hole, and the power from the drill is transmitted to the cutting tool through drill rods or pipes. In order to keep down the volume of rock that must be ground to sludge, the cores in large-diameter drilling are made as large in diameter as possible. Their large diameter increases their weight per foot of length, which

Jan 1, 1939

By Ernst F. Eurich

Alexander Parkes patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the United States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverbera-tory furnace. If the lead was too impure, it was first softened

Jan 1, 1913

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By Otto H. Henry, Edward L. Badwick

Up to the present time, according to Hansenl and Haughton,² the constitution of the bismuth-indium system has not yet been published. The generally accepted value for the melting point of indium, as listed in most scientific journals and textbooks, is 155°C. Recently, however, H. M. Davis3 has determined a new melting point for indium of 157.3²C O.l°C. Since bismuth has been used in preponderance as an alloying element in the majority of low-melting alloys, and indium has been used with considerable success in lowering the melting points of low-melting alloys, 4,6 an interest has been developed in the application of these two metals, making a complete knowledge of the constitution of its alloys desirable. In this investigation, the melting point of indium reported by H. M. Davis has been found to be substantially correct. A value of 157. ²°C ± O.5°C was determined. The two eutectic compositions have been placed at 34 and 50 pct bismuth with their respective eutectic temperatures as 72.4°C ± 0.5°C and 90°C ± 0.5°C. The bismuth-indium phase diagram has been determined by thermal and microscopic analysis and is shown in Fig I. Thermal Analysis Granulated bismuth and indium shot, having a guaranteed purity of 99.99 and 99.95 pct, respectively, were melted in a carbon crucible by means of a laboratory heater. To minimize oxidation of the alloys, a heavy mineral oil (Nujol) having a high- flash point was used. A platinum-platinum rhodium thermocouple of fine wire encased in a thin-walled Pyrex glass tube, about 1/8 in. in diameter, was connected to a type K potentiometer for temperature measurements. The thermocouple was calibrated against the melting points of tin, bismuth, and the silver-copper eutectic and the boiling point of water. Since the temperature readings could be reproduced to 0.²°Cl and the accuracy of the temperature standards in this range is slightly better than 0.5°C, it scems reasonable to assume that the temperature readings are reliable to approximately 0.5°C. The cooling rate could be controlled by varying the amount of insulation surrounding the crucible. Three or four layers of asbestos paper, 1/16 in. thick, sufficed to give a cooling rate of from I° to ²°C per minute. Undercooling was slightly noticeable. This condition was minimized by vigorous stirring, since the advantage of using slower rates was too small to justify the greater expenditure

Jan 1, 1947

By N. J. Keys, B. Barlin

Operating properties of Bancroft Mines Ltd. are in the Western Province of Northern Rhodesia, just south of the Katanga border and at the north- western end of the Rhodesian Copperbelt. The concentrator, above, was commissioned in January 1957 to treat 150,000 tons per month of ore derived from the nearby Kirila Bomwe South orebody, and the Konkola orebody eight miles away. The Konkola orebody is comparatively low grade and mining was discontinued there in early 1958. Development work on the new mine at the Kirila Bomwe North orebody commenced in 1959. Today, the plant treats approximately 150,000 tons of ore per month from the Kirila Bomwe South orebody and development ore from the north orebody. Ultimately, 100,000 tons of ore per month will be produced from the north orebody.

Jan 9, 1963

By William Barrett

IN order properly to evaluate the data related to geomagnetic surveys, it is highly desirable to have all the available information concerning the magnetic properties of the, involved media. This is true of surface as well as subsurface formations and becomes of increasing importance as advancement in instrumental and interpretative technique permits the analysis of relatively slight magnetic reflections of buried masses. Since the magnitude and areal distribution of the usually complex resultant magnetic field at the surface of the earth is a function of the susceptibility1 of the involved matter, it necessarily follows that susceptibility determinations will afford valuable data for geophysical correlation. The present method was developed to meet the need for routine analysis of specimens in the geomagnetic laboratory where it was felt that general utility, ruggedness, ease of manipulation and reproducibility of results was of greater importance than extreme sensitivity.

Jan 1, 1931

By J. H. Jackson, P. D. Frost, C. H. Lorig, A. C. Loonam

THIS paper describes (1) the effect of sodium on the tensile ductility of magnesium-lithium base alloys, and (2) the precautions necessary to avoid sodium contamination. Effect of Sodium on Properties The harmful effect of sodium in magnesium-lithium base alloys has been recognized by other investigators.1,2 However, quantitative data on its effect have not hitherto been published. The effect of sodium on the ductility of an 87 pct Mg-9 pct Li-4 pct Zn alloy is shown in fig. 1. The sodium was introduced by adding sodium chloride to the flux, which consisted of 50 pct LiC1-50 pct KC1. Moderately high ductility was obtained at an indicated sodium content of about 0.05 pct. Actually, the value probably was less than 0.05 pct, be-cause analyses of the lithium, which were more accurate than those of the alloy, indicated that the highest ductility was obtained when its sodium content was 0.02 pct or less. In fact, in alloys having somewhat greater strength than this particular composition, the sodium content of the lithium must be under 0.01 pct to avoid embrittlement. The effect of sodium on the ductility of several alloys having fairly low strength levels is shown in fig. 2. These alloys were melted with a flux containing 75 pct LiC1-25 pct LiF, to which various quantities of sodium chloride had been added. Sodium had no significant effect in pure magnesium but markedly decreased the ductility of the magnesium-lithium-zinc alloy, even though the alloy contained only 3 pct Li. As the lithium content of the binary alloys was increased, the ductility of the sodium-free alloys also increased. However, the effect of sodium on ductility became progressively more pronounced. Sodium raised the minimum hot-rolling temperatures, particularly those of the high-strength alloys, but its effect, in this respect, was less critical than its effect on tensile ductility. For optimum cold roll-ability, a low-sodium content was required. No deleterious effect of sodium on the stability of properties at slightly elevated temperatures was found. Control of Sodium in the Alloys Optimum ductility is obtained in the magnesium-lithium base alloys when sodium-free materials are used. Commercial lithium was formerly the chief source of contamination. Now purified lithium is usually available. When lithium of ordinary purity is used, the effects of sodium can be minimized by using a flux consisting of 75 pct LiC1-25 pct LiF. Bubbling nitrogen through the melt also helps remove sodium. The damaging influence of sodium on the ductility of the magnesium-lithium base alloys was observed very early in the alloy development program. The discovery came about as a result of chemical analyses made on the lithium used in the alloys. Ductile alloys had been made from lithium containing about 0.2 pct Na, whereas the lithium used in the brittle alloys contained about 0.9 pct Na. The first magnesium-lithium alloys were melted under commercial fluxes ordinarily used in melting magnesium alloys. These fluxes were unsuited for scavenging the contaminating sodium, and the resulting alloys were not ductile. Next, a flux containing 50 pct KC1-50 pct LiCl was tried. This was somewhat more effective but still was not satisfactory. After a number of different experimental fluxes had been investigated, one containing 75 pct LiC1-25 pct LiF was adopted. This flux made it possible to obtain good ductility in the alloys. The

Jan 1, 1951

By Leland H. Johnson

THE Tennessee Coal, Iron & Railroad Co.'s ore mines began experimental tests with trackless mining units early in 1947. The units had many weaknesses to overcome, but are now well beyond the experimental stage and are becoming a necessity to ore seams that are amenable to this type of equipment. The development of this type of mining with the problems of increased underground supervision, maintenance, and training personnel, along with the benefits derived, are discussed.

Jan 12, 1950

By V. H. Wilhelm

The trend initiated in January 1936, of stabilized gasoline prices, increased demand and extraordinary drilling activity, continued in California during the year 1937. Crude prices were maintained during the year at the highest level since September 1930. Wildcat activity with resultant new discoveries and development of proven acreage were greater than in any year since 1928. Many fields in California in former years have been produced at full capacity, with consequent loss of reservoir energy, but at the present time continued activity is maintained to develop adequate reserves, so that production in these fields can be taken at a rate to correspond with good operating practice. Naturally, this good operating practice will be influenced to some degree by gas outlets and, in certain instances perhaps, by oil outlets. In any event, these last two controlling features will result in favorable rather than detrimental operation. In fields producing from great depths, ultimate production will be practically limited to the flowing and compressor life of the well, since there is as yet no economical method for pumping wells below depths of approximately 7000 ft. Experience has shown, however, that such pumping difficulties will be overcome and that production secured by pumping will add some to reserves established on the flowing life of the wells. California continued to operate under voluntary curtailment, but with unlimited transfers of allowable between various fields. Even though there was at all times considerable production above the Umpire's established quota, a constantly increasing demand reduced storage during the year. This increasing demand was due mainly to the rapid rise in Pacific foreign shipments from May to September. It is questionable, however, whether this favorable condition will be maintained over a prolonged period. (See Fig. 1.) Field Discoveries The great drilling activity during the year resulted in the discovery of three new fields in the San Joaquin Valley, as well as many extensions

Jan 1, 1938

By John Wulff, J. H. Hollomon

Service failures in brass condenser tubes are often due to corrosion. One of the commonest types of corrosion reveals a surface structure of redeposited copper.' The study of the effect of alloy addition agents in preventing this kind of corrosion has received impetus from the extensive publication of Bengough and May.2 The mechanism of such inhibition gauged from immersion corrosion,2 cell corrosion,3 and electrolytic potential4 measurements is controversial. This controversy may be attributed in part to a lack of definite knowledge5 of the actual nature of the initial films formed in corrosion experiments. In our own corrosion work on copper and 70-30 brass this lack became apparent and necessitated an examination of surface films by X-ray and electron diffraction methods. The present paper is but an introduction to the subject of inhibition and reports the structure of films formed in active corrodents. Experimental Procedure The arsenical coppers and brasses used in this investigation were made by one of the writers* in the plant of the Revere Copper and Brass Co. at Rome, N. Y. Standard commercial melting practice was followed. O.F.H.C. copper and electrolytic zinc were used and all arsenic additions were made by additions of a master copper alloy. The final analyses are given in Table I. Likewise, the extrusion, cold-rolling, and intermediate anneals employed followed standard usage. Final heat-treatments were given to all materials to produce a similar grain size (0.035 to 0.045 mm. for brass and 0.015 to 0.025 for copper) for the alloys containing various percentages of arsenic. Samples 1/2 by M by 1/4 in. were cut from sheet material resurfaced and finished with 0000 metal-lographic papers. The surfaces were all degreased in alcohol and benzine before immersion. After immersion in the corrodent, they were washed gently in tap water, dipped first in alcohol and then in pure benzine and allowed to dry in the diffraction apparatus. The reflection electron diffraction apparatus used has been described by Burwell and Wu1ff.6 Fig. I is typical of the photo-grams obtained. The X-ray apparatus was

Jan 1, 1941

By John Wulff, J. H. Hollomon

Service failures in brass condenser tubes are often due to corrosion. One of the commonest types of corrosion reveals a surface structure of redeposited copper.' The study of the effect of alloy addition agents in preventing this kind of corrosion has received impetus from the extensive publication of Bengough and May.2 The mechanism of such inhibition gauged from immersion corrosion,2 cell corrosion,3 and electrolytic potential4 measurements is controversial. This controversy may be attributed in part to a lack of definite knowledge5 of the actual nature of the initial films formed in corrosion experiments. In our own corrosion work on copper and 70-30 brass this lack became apparent and necessitated an examination of surface films by X-ray and electron diffraction methods. The present paper is but an introduction to the subject of inhibition and reports the structure of films formed in active corrodents. Experimental Procedure The arsenical coppers and brasses used in this investigation were made by one of the writers* in the plant of the Revere Copper and Brass Co. at Rome, N. Y. Standard commercial melting practice was followed. O.F.H.C. copper and electrolytic zinc were used and all arsenic additions were made by additions of a master copper alloy. The final analyses are given in Table I. Likewise, the extrusion, cold-rolling, and intermediate anneals employed followed standard usage. Final heat-treatments were given to all materials to produce a similar grain size (0.035 to 0.045 mm. for brass and 0.015 to 0.025 for copper) for the alloys containing various percentages of arsenic. Samples 1/2 by M by 1/4 in. were cut from sheet material resurfaced and finished with 0000 metal-lographic papers. The surfaces were all degreased in alcohol and benzine before immersion. After immersion in the corrodent, they were washed gently in tap water, dipped first in alcohol and then in pure benzine and allowed to dry in the diffraction apparatus. The reflection electron diffraction apparatus used has been described by Burwell and Wu1ff.6 Fig. I is typical of the photo-grams obtained. The X-ray apparatus was

Jan 1, 1941