Search Documents

By R. L. Schmidt, J. D. Verhoeven

The diffusion coefficients and electrotralzsport mobilities of aluminum, gallium, and arsenic have been determined in molten germanium with the capillary reservoir technique. The diffusion coefficients are slightly higher than those determined by the solidification technique of Brirton et a1.1 It was found that aluminium and gallium migrate to the cathode in molten germanium) whereas arsenic migrates to the anode under an electric field. A possible technique for producing p-n junctions by means of electric field freezing is discussed in view of the experimental data. In the past decade or so the literature has abounded with articles concerning the solid-state properties of the semiconducting elements germanium and silicon. It is surprising by comparison how little has been published concerning the liquid-state properties of these materials. In the production of doped germanium or silicon the diffusion coefficient of the dopant in liquid germanium or silicon is an important quantity. Yet, to the best of our knowledge, no one has ever made a direct measurement of the diffusion coefficient of solutes in either molten germanium or silicon. A number of authors'-4 have determined some diffusion coefficients by the indirect technique developed by Burton et al.1 This technique appears to give numbers of the correct order of magnitude but it does depend upon a number of assumptions in the analysis and also requires prior knowledge of the viscosity of the melt. In the present work a more direct measure of the diffusion coefficients of arsenic, gallium: and aluminum in molten germanium has been made. It has been shown independently by two groups of authors5, 6 that, when an electric current is passed through the interface of a solidifying metal containing an impurity, the resulting electrotransport in the liquid boundary layer at the interface offers a mechanism for control over the redistribution of the impurity accompanying the solidification. These authors show that the degree of control is proportional to the mobility, U of the impurity atoms in the liquid boundary layer, where the mobility is defined as the drift velocity relative to the solvent per unit electric field. In principle the results apply to the solidification of a doped semiconductor and offer an interesting technique for control of the doping of a semiconductor. In the present work the mobilities of aluminum, gallium, and arsenic were determined in molten germanium in order to evaluate the potential usefulness of electro-transport as a technique for solute control when applied to the solidification of doped germanium. EXPERIMENTAL PROCEDURE Both the diffusion coefficients and the mobilities were measured using high-purity alumina capillaries and a resistivity technique for analysis. A schematic diagram of the electrotransport apparatus is shown in Fig. 1 and the details of the cell design are shown in Fig. 2. For the mobility experiments electrical contact with the bottom of the capillary was made with graphite, as shown in Fig. 2. In order to prevent electrical contact with the melt the graphite was coated with a thin layer of alumina using a plasma spray torch. The cell assembly, a graphite electrode, and another assembly containing two blank capillaries were fastened to the lavite disk shown in Fig. 1. To make a run the system was evacuated and the doped germanium was outgassed at the operating temperature of 1030°C. The cell and blank capillaries were then submerged beneath the melt and a slightly positive pressure of helium was introduced to fill them. After passing current through the cell for a given time the cell and blank capillaries were raised from the melt and the furnace was shut off. The temperature of the cells dropped below the freezing point of germanium within 1 to 2 min after the furnace was shut off.

Jan 1, 1968

By Charles M. Cooley

With explosives representing over 10 pct of the cost of operating the entire company, the Maumee Collieries Co., Terre Haute, Ind., inaugurated a program to develop a low-cost blasting agent. Results of more than two years' work were announced on May 1 by Hugh B. Lee, president of the company. Utilizing a mixture of commercial-grade ammonium nitrate and carbon black packed in polyethylene bags, Maumee has been able to reduce blasting costs by 50 pct. The lower costs are brought about principally by elimination of high transportation charges on fixed explosives and use of low-cost material (commercial NH,NO, and carbon black). The Akremite blasting method incorporates a 20-lb cap-sensitive primer to detonate the stable explosive. Maumee now uses Akremite exclusively in its stripping operations producing more than 2 million tons of coal per year. The explosive is employed to break about 25 million cu yd of overburden that covers the coal

Jan 5, 1955

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By D. E. Thomas, C. E. Birchenall

ALTHOUGH Eoltzmann gave a mathematical solution for the diffusion equation (for planar diffusion in infinite 01. semi-infinite systems only) in 1894 allowing for variation of the diffusion coefficient with a change in concentration, it was not until 1933 that this solution was applied to an experimentally investigated metallic system. The calculation was carried out by Matano' on the data obtained by Grube and Jedele3 for the Cu-Ni system. Since that time concentration dependence of the diffusion coefficient has been demonstrated for many pairs of metals. However, the nature of this dependence has never been fully elucidated. Many investigators have suspected that these variations could be related to the thermodynamic properties of the solutions, one of the earliest explicit statements being contained in a discussion of irreversible transport processes by Onsager' in 1931. Development along these lines has been greatly retarded by the lack of reliable data on the variation of tliffusivity with concentration, the paucity of the thermodynamic data for the same systems at the same temperatures and compositions, and an incomplete understanding of the relation of the thermodynamic properties of the activated state for diffusion to the bulk thermodynamic properties. The last factor has been discussed by Fisher, Hollomon, and Turnbull.5 In many instances where data exist, it is difficult to know which are acceptable. This problem probably applies more strongly to diffusion data than to activity measurements. For instance, four sets of observers"-" have reported self-diffusion coefficients for copper. The average spread between extreme results is a factor of about four, though the individual sets of data are self-consistent to about 20 pct. Thus one or more factors are out of control, at least in these experiments, making estimates of internal error unreliable. The most reliable diffusion data in most systems have resulted from the use of welded couples with a plane interface from which layers for analysis are machined parallel to the interface after diffusion. The layers are analyzed, and the result is a graphical relation between distance and concentration, usually called the penetration curve. Given the same set of analytical data and distances and following the same procedure in computation, different observers will generally produce diffusion coefficients which vary appreciably, especially at the extremes of the concentration range. Experiments must be carefully designed so that the precision is good enough to answer a particular question unequivocally. In the first calculation of the dependence of the diffusion coefficient on concentration in the metallic solid solution Cu-Ni, Matano found that the coefficient was insensitive to concentration from 0 to 70 pct Cu, after which it rose more and more steeply to some undetermined value as pure copper was approached.' The same behavior was reported for Au-Ni, Au-Pd, and Au-Pt.* The data used were those of Grube and Jedele which were very good at the time, but are not considered particularly good by present standards. Furthermore, the method of calculation makes the ends of the diffusion coefficient-concentration curve unreliable. For better reliability, the high copper end of the curve has been checked by incremental couples, where the concentration spread is 67.7 to 100 atomic pct Cu. The implication of the curves calculated by Matano was that diffusion is very concentration sensitive in one dilute range of this completely isomorphous system and hardly at all in the other. Matano's result is confirmed. Later Wells and Mehll0 published data on diffusion in Fe-Ni at 1300°C, which represent a thorough test of the shape of the concentration dependence curve. They ran couples with the following ranges of nickel concentration: 0-25 pct, 1.9-20.1 pct, 0-20.1 pct, 20.1-41.8 pct, 0-99.4 pct, and 79.3-99.4 pct. Although the trend of the data indicates an S-shaped concentration dependence, their curve was drawn to the pattern set by Matano. Their original data have been recalculated for the 0-99.4 and 79.3-99.4 pct couples. Wells and Mehl's points and two independent recalculations from the raw data are plotted in Fig. 1. What appears to be the best curve is drawn through them. This curve shows little sensitivity to composition in both dilute ranges with a strong dependence at intermediate composi-tions.? Similar experiments on the Cu-Pd system are reported here at temperatures where solubility is unlimited. These lead to the same type of concentration dependence for the diffusion coefficients as was found upon recalculation of the data for the Fe-Ni system. Experimental Procedure Cu-Pd: The concentration dependence of the diffusion coefficient may be determined by the use of

Jan 1, 1953

By R. E. Stewart

The major mining companies of the world all face the problems associated with investing in new mining ventures. In particular, investment in foreign countries - whether these are advanced or developing countries - requires careful consideration. A thorough analysis of all the possible risks must be undertaken, so that realistic decisions can be made. Some of the points to be considered are outlined in this paper.

Jan 1, 1977

By V.K. Zworykin

Throughout its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes: it has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron . Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction —at the very best a tenth—of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. TO overcome it, a different imaging medium must be employed, The existence of such a medium became evident when it was demonstrated1 that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed. Furthermore, although a wave length may . be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light. Actually, the elcctron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. The Electron Microscope Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the clectrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By V. K. Zworykin

Throughout its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes: it has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron . Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction —at the very best a tenth—of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. TO overcome it, a different imaging medium must be employed, The existence of such a medium became evident when it was demonstrated1 that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed. Furthermore, although a wave length may . be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light. Actually, the elcctron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. The Electron Microscope Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the clectrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By E. J. Rapperport, E. D. Levine

The boundaries of the (a +ß) field in the Al-Li system were determined between 150°and 550°C utilizing quantitative metallography and lattice-parameter measurements. The solubility of lithium in aluminum decreases from 12.0at. pct Li at 550°C to 5.5 at. pct Li at 150°C. P Al-Li is saturated with aluminum at 45.8 at. pct Li and has this boundary value constant over the temperature range 150°to 550°C. THE solid solubility of lithium in aluminum has been determined by several investigators, 1-6 but, as shown in Fig. 1, there is little agreement among the various determinations. The earliest investiga-tions'-' are suspect because of the use of impure materials. Although high-purity materials were employed in more recent work,4'5 the experimental techniques may have led to contamination of the specimens. Probably the best work has been that of Costas and Marshall,6 who obtained close agreement between results obtained by two independent phase-boundary techniques: electrical resistivity and mi-crohardness. No detailed studies of the solubility of aluminum in the bcc ß phase, Al-Li, have been reported. Cursory investigations1,2,6 have indicated only that the (a+ß) -p boundary lies between 40 and 50 at. pct Li and is relatively independent of temperature. The present work was undertaken in order to provide an independent check on Costas and Marshall's determination of the solubility of lithium in aluminum, to extend knowledge of this solubility limit to temperatures below 225°C, and to make an accurate determination of the solubility of aluminum in Al-Li. EXPEFUMENTAL Alloy Preparation. In view of the difficulties encountered in previous investigations of the A1-Li system, close attention was paid to the use of methods of alloy preparation and treatment that would minimize contamination. Aluminum sheet (99.99 + pct Al) was vacuum-induction melted in a beryllia crucible to remove hydrogen. Lithium (99.9 pct Li) was charged with pre-melted aluminum into a beryllia crucible, in a helium-filled drybox. The crucible was sealed in a Vycor tube and transferred from the drybox to an induction furnace. Melting of alloys was performed by induction heating in a helium atmosphere. Solidification was accomplished by means of a suction apparatus, shown in Fig. 2, in which the alloy was forced by changes of pressure into a 3/16-in. inside diam closed-end beryllia tube. This technique produced rapid solidification of a small portion of the melt, resulting in alloys with a high degree of homogeneity. Typical lithium distributions are presented in Table I. Transverse sections 1/8 in. long were cut from the alloy rods, and each section was split in half longitudinally. One half of each section was analyzed for lithium, and the opposing halves were employed for phase-boundary determinations. Lithium contents were determined by flame photometry with an accuracy of 1 pct of the amount of lithium present. Thermal Treatments. Homogenization and equilibration heat treatments were performed in electrical-resistance furnaces with temperatures controlled to ± 2OC. Calibrated chromel-alumel thermocouples were employed to measure temperature. Homogenization was performed in helium-filled l?yrex tubes for 1 hr at 565°C. The encapsulated specimens were then transferred directly to furnaces maintained at lower temperatures for equilibration. Equilibration times were 2 hr at 550°C, 8 hr at 450°C, 27 hr at 350°c, 90 hr at 250°c, and 285 hr at 150"~. These times were chosen on the basis of conditions employed by previous investigators. Alloys were quenched from the equilibration temperatures by breaking the capsules into a silicone oil bath. By performing all possible operations either in sealed capsules or in a helium-filled drybox, the specimens were given minimum exposure to the atmosphere. Quantitative Metallography. Metallography of Al-Li alloys is difficult because of the atmospheric reactivity of the ß phase. It was found possible, however, to prepare surfaces of good metallographic quality by preventing contact with moisture during preparation. Grinding through 4/0 paper was performed in the drybox. The specimens were then transferred under kerosene to the polishing wheel. Three polishing stages were employed: 25-p alundum with kerosene lubricant on billiard cloth, 1-µ diamond paste on Microcloth, and 1/4-p diamond paste on Microcloth. Between stages the samples were cleaned by rinsing in trichloroethylene and buffing

Jan 1, 1963

By Julian E. Tobey

A MEMORABLE year has just passed in the field of coal utilization. Because of the war, oil conversions in industrial, commercial, and domestic installations have been made to the equivalent of 20,000,000 tons of coal. The war emergency has resulted in a great shifting of various types of coals to various markets. Huge tonnages of metallurgical-quality coals have been withdrawn from steam and domestic business and sent into the iron and steel industries. Marginal coals have replaced these coals in the steam and domestic field.

Jan 1, 1944

By Morris A. Steinberg

Because of the broad scope of my topic I will discuss my subject from the point of view of a present status of the metallic materials that are used in structures and will dwell primarily on those structures related to high- performance aerospace systems. Thus, I can best portray the status of these structural materials as related to existing transportation systems, delineating some of the highlights of alloy development, fabrication, and properties obtained. I shall point out what are, in my opinion, the needed solutions to pressing unsolved metallurgical problems connected with certain selected metals: aluminum alloys, beryllium, titanium, steels, superalloys, refractory metals and some metal-matrix composites. Aluminum Alloys For a number of years a series of strong aluminum alloys used for airframes has had an important bearing on the development of minimum- weight, highly efficient structures. Among these alloys are such familiar ones as 2024-T3, 2014-T6, 7075-T6, 7079-T6 and 7178-T6. A review of the development and use of strong aluminum alloys in aircraft structures indicates that before about 25 years ago there was very little application of products other than forgings in the high-strength tempers produced by precipitation heat treating to T6- or T8-type tempers. 1 As stated by Dix in 1944, "There has been a gradual evolution in engineering viewpoint regarding the mechanical characteristics which are required in a structural material suitable for aircraft. Formerly, emphasis was placed on a generous spread between yield and tensile strengths, on elongation, on impact strength and on resistance to corrosion. Aircraft structural engineers still differ widely as to the importance which they attach to these proper tie.” 2 It is fair to say that this evolution is still taking place, that the problem is much the same in 1970 as in 1944 - except that strength levels have advanced some - and the question remains as to how far we can go in that direction. In the meantime, a new group of alloys has received acceptance and widespread use. The first alloy of this group, 7075-T6, was formally introduced by Dix's 1944 paper. The drastic changes that have taken place in the size and configuration of components employed in air-

Jan 1, 1971

By James S. Browning

The Bureau of Mines conducted laboratory and small-scale continuous tests of kyanite ore from Georgia and South Carolina to determine the technical feasibility of recovering commercial grade kyanite concentrates by flotation. The research indicated that combinations if sulfuric acid and petroleum sulfonate may be used effectively for flotation of kyanite from quartzite-kyanite ore. This report summarizes the results of these tests, and demonstrates the feasibility of producing commercial-grade concentrates with a high recovery of the contained kyanite. Extensive deposits of kyanite occur in the southeastern United States. The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate for many years at the present rate of consumption. According to Espenshade and Potter,' the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30% kyanite. The tonnage of kyanite-bearing gneiss and schist is much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina-South Carolina, and at Graves Mountain, Ga. Of the known deposits, only four were being mined for kyanite in 1 967. These deposits are near Farmville and Dillwyn, Va., Clover, S.C., and Washington, Ga.

Jan 1, 1970

C. A. HANSEN (communicated appendix*).-Since the above paper was written, tests have been conducted with a view to securing a sounder basis for discussing the effects of temperature on the behavior of the zinc cell. The following data, while making no pretense to great accuracy, are still reasonably close. Cells were operated with the same feed solutions, but at varying temperatures, the latter being controlled by means of immersed steam coils. Current efficiencies obtained indicate that the corrosion rate

Jan 11, 1918

By Ralph Sherman

THE remarkable increase in the distribution of the small underfeed stoker for use in furnaces and boilers in small industrial plants, apartment houses and homes has brought producers and distributors of bituminous coal to consider the problem of which coals and which sizes are best suited to this market. Many papers have also appeared, mostly in the trade journals, discussing the problem of the combustion of various coals and various sizes of coal in small stokers. Much difference of opinion has been apparent in these articles; due often, it would appear, to a mis-understanding of the fundamentals of the process of combustion in the stoker fuel bed. During the past year and a half, a program of research has been conducted at Battelle Memorial Institute: (1) On the process of combus-tion in the fuel bed of the small stoker, sponsored by Battelle Memorial Institute, and (2) on the relation of the characteristics of bituminous coals to their performance on small underfeed stokers, sponsored by Bituminous Coal Research, Inc. As a result of this program of research, two publica-tions have been made, one1 dealing with the problem of clinker formation, and the other2 with the relation of the size of the coal fed to the stoker hopper to that of the coal that reaches the retort to be burned. The experimental research on the relation of size to the performance of the coal is being actively continued. A publication of Bituminous Coal Research, Inc. presenting the data obtained on the performance of several sizes of four typical bituminous coals will appear shortly. Because of the early appearance of that publication, the present paper includes few numerical data. The purpose of this paper is to follow the coal from the hopper through the furnace with a discussion of the various actions that occur, in the hope that it will lead to a clearer understanding of the relation of the type of coal, the size of coal, and other characteristics, to the performance. The authors do not pretend to have obtained the answers to all the complex questions involved; many unanswered questions will be proposed on which future research work is planned.

Jan 1, 1936

By S. M. Bishoff

The disturbance of surface land to support the underground mining of coal requires several hundred acres to produce easily in excess of $1 billion in sales at a moderately sized mine over 20-30 years. Due to the recent influx of environmental legislation, these surface operations must now undergo complete reclamation upon permanent cessation of production. This reclamation procedure has become so complex that the cost of reclamation must be a major consideration in the design of a new mine. This presentation will discuss these costs as they may be methodically evaluated and surcharged as a percentage of the product price. When placed in the proper, logical perspective, it is anticipated that the obstacles involved in this process may be minimized.

Jan 1, 1985

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of' the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.',' The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949

By R. A. Morse, W. O. Keller

The properties of limestone reservoir rocks such as the distribution and degree of continuity of the pore systems, and the relative volumes and permeabilities of the systems making up the complex cause large variations between performance of individual limestone reservoirs and their susceptibility to secondary recovery methods. The effects of these factors on the mechanism of fluid flow cannot be adequately evaluated with presently developed concepts, laboratory data, and geological information. The observance and interpretation of the performance of individual limestone reservoirs provides, at present, the most adequate approach for evaluating the integrated effects upon performance of the many. now immeasurable variations in the properties of limestone reservoirs. INTRODUCTION The development and application of techniques for increasing the efficiency of oil recovery from natural reservoirs is a problem of primary importance to the industry. During the past several years, a great deal of effort has been expended by the technical personnel of the industry toward the improvement of present known methods of oil recovery. and evaluating the factors which control the susceptibility of particular reservoir types to economic application of secondary recovery methods. Providing adequate and accurate laboratory data on the properties of the reservoir rock and its contained fluids. together with good production statistics, are available, methods have been evolved for estimating with reasonable accuracy the performance of an oil reservoir under either continued natural depletion or conditions imposed by introducing additional displacing fluid into the reservoir from an extraneous source through the injection of gas and/or water. The susceptibility of limestone reservoirs to secondary recovery by gas injection is very much dependent upon gas-oil relative permeability relationships for the reservoir in question. In a rock formation in which the porosity is of the intergranular type such as is found in sand stones and some non-fractured dolomites, a representative sample of the pore structure can be obtained in a small core plug. In this type of reservoir, it has been shown that relative permeability data obtained from laboratory experiments can be Properly applied to evaluate the flow relationships actually observed during the depletion of a reservoir. In addition, a good idea of the fraction of the reservoir which will be swept by the injected gas may be obtained from the spacing pattern used and the permeability profile of cored wells. From these data, it has been demonstrated that reliable estimates of performance and recoveries under gas injection operations can be made for reservoirs in which the Porosity is of the intergranular type. Limestone reservoirs on the other hand often present much more complex problems. One reason that the performance of limestone reservoirs is so variable is that there may be, in reality. two or more pore systems, the integrated performance of which will depend upon the physical properties of each system and their inter-relationship. For instance, in a limestone reservoir, the main pore structure, as far as void spaces for storage of hydrocarbons is concerned, may be represented by the intergranular openings of the rock. Usually in limes and dolomites, the intergranular pore openings are very small and the matrix permeabilities extremely low. Often, as in the case of Many dolomite and oolitic lime reservoirs, this is the only pore system, and performance is observed to be very similar to that of a sand stone of similar permeability. However, in the great majority of' the limestone reservoirs, there is present, in addition to the intergranular pore system, a complementary system of openings caused by fracturing or solution.',' The openings in the latter system are usually many times more permeable than the intergranular pore system due to their much larger size, and may contribute almost all the fluid carrying capacity of the formation, even though their volume may be a very small part of the total pore space in the reservoir. Obviously, the performance of such a complex under either primary or secondary control will deend upon the distribution and degree of continuity of both systems, the relative volumes and permeabilities of the

Jan 1, 1949

By Julian M. Avery

IN its dual role of pig-lion smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose During the past 10 years or more, improvements in blast-furnace technique and economy have, n fact, been directed primarily to increasing efficiency n the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace The net over-all result is a decrease n the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently amore than offset n value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements The purpose of the present paper is to suggest that, while progress has been made n this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all economy of a different order of magnitude than results thus far obtained by the use of other expedients The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss can be successfully attacked by increasing the over-all pressure, i e , the "top pressure" under which the furnace is operated It is indicated that pressure operation may also be expected to result n concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By W. E. Newell

The basic principles and assumptions involved in D. L. White's solution5 for ultrasonic wave amplification in piezoelectric semiconductors are summarized. If the gain per unit length is maximized at each frequency without regard to the drift-field power density, the gain increases linearly with frequency. Therefore it would seem that very high gain is possible for frequencies in the hundreds of megacycles. However, with present materials the resulting drift-field power density is so large that cooling would be a major problem. For this reason it is more realistic to judge the capabilities of an ultrasonic amplifier in terms of the gain that is possible with a specified power density. In this case the gain at high frequencies does not increase but decreases more rapidly than l/f. The calculation of the gain us frequency at a fixed power level involves the repeated solution of a cubic equation and is therefore tedious. For the purpose of comparing different materials, sufficient accuracy can be obtained from an approximate solution which may easily be plotted as three straight lines on logarithmic graph paper. This method is used to compare the Performances of CdS, CdSe, ZnO, and GaAs. At a power density of 10 watts per cu cm, the first three give maximum gains of 60 to 80 db per cm in the vicinity of 60 megacycles. At the same power density, GaAs has a maximum gain of about 7 db per cm near 150 megacycles. Although an increase in mobility usually increases the gain for a specified power density, it is shown that there is an optimum mobility above which the gain decreases. An approximate expression for the optimum mobility is established. It is well-known that the interaction between charged particles and an electromagnetic wave can be used to amplify the electromagnetic wave. In the conventional traveling-wave tube, electrons in a vacuum are caused to move at a velocity slightly greater than the wave velocity, thereby coupling energy into the wave.' In principle, the same effect would be evident in a solid except that repeated collisions prevent the electrons from attaining a velocity greater than that of an electromagnetic wave. However, the drift velocity of electrons can be made to exceed the velocity of an acoustic wave in a solid. In 1956, weinreich2 noted that the deformation potential provided one means of coupling energy from drifting electrons into an acoustic wave, but the effect was too small to be of any practical importance. It was not until 1961 that White and Hutson demonstrated that the piezoelectric effect provided a strong enough coupling to give appreciable amplification of an ultrasonic wave and awakened wide interest in electron-phonon interactions. Qualitatively the effect may be described as follows. An acoustic wave propagating through a piezoelectric material is accompanied by an electric-field wave. If the vibrations are properly oriented with respect to the crystal axes of a piezoelectric semiconductor, the local electric fields are axially directed and cause bunching of the charged carriers. If the drift velocity of these carriers is less than the velocity of sound, they tend to be dragged along by the acoustic wave. This electroacoustic effect results in a net potential appearing across the material and in attenuation of the acoustic wave. On the other hand, if the drift velocity exceeds the velocity of sound, energy is coupled from the carriers to the acoustic wave and amplification results. Related effects which are being investigated include ultrasonic amplification in semimetals6-' and semi-conductor, and current saturation in piezoelectric semiconductors.'4-17 There are various problems which hinder the immediate application of ultrasonic amplification in a practical device. First, there are the traditional problems encountered in the design of acoustic delay lines: attenuation in the electromechanical transducers, reflected waves (which can lead to self-oscillation in an amplifying device), mechanical tolerances necessary to maintain phase coherence, and so forth. Second, there is the problem of selecting the best material from among the various piezoelectric semiconductors as they become available in single-crystal form with a wide choice of characteristics. This paper deals with the second problem and shows that the most realistic way of comparing materials is in terms of the gain which can be obtained without exceeding a

Jan 1, 1964

By John T. Norton, R. E. Hiller

The tremendous increase in the use of metals that have been prcpared by the various cold-working processes during recent years has greatly stimulated the investigation of problems concerned with the fundamental nature of these processes. It has been observed in practice that different methods of bringing about the same dimension changes in a sample result in a rather wide range of properties. Cold working reduces the ductility of a metal, or what is perhaps more nearly correct, its "working capacity," and naturally the manufacturer wishes to produce an article that has as large a working capacity as possible, and to produce it with the smallest number of operations. It has also been known for some time that cold deformation produces a parallel alignment of the crystal grains of a metal, and that the type of this preferred orientation depends to some extent at least upon particular processes employed in the deformation. The present investigation has for its purpose the study of the relations between the various factors of a cold-working process and the preferred orientation of the metjal crystals resulting from this deformation. The work is chiefly confined to a study of cold-drawn seamless tubing. Preparation of Samples The tubing samples used in this investigation were made of steel having a carbon content of 0.10 to 0.20 per cent, and were drawn on a standard type of draw bench. In order to obtain the large reductions, the annealed stock was coated with lead, for purposes of lubrication. The reductions of area stated refer to reduction from the annealed condition without intermediate heat treatment. The cold work was done as nearly as possible at room temperature. The samples of wire and strip used for purposes of comparison were of steel of approximately the same carbon content and were prepared in the manner indicated. X-ray Method of Investigation The condition of preferred orientation in cold-worked samples is best investigated by the X-ray method that employs a small circular beam of * Assoriate Professor of Physics of Metals, Massachusetts Institute of Technology. t Graduate Student, Department of Metallurgy, Massarhusetts Institute of Technology.

Jan 1, 1932

By J. B. Austin, R. L. Rickett

Measurements of the rate of decomposition of austenite at constant temperature are commonly represented by plotting the percentage transformed on linear coordinates against time on either a linear or a logarithmic scale, a method that yields a curve that in shape resembles an integral sign (Fig. 1). A graph of this kind is not always convenient because extrapolation to the beginning or end of the transformation, or even intebrpolation, may be uncertain unless there are a large number of observations, which seldom happens; furthermore, the degree of consistency of a set of measurements is difficult to judge from such a curve. It is desirable therefore to find some mode of plotting, or even better to find a standard variety of graph paper, that gives a straight line instead of the integral shape. The straight line has many advantages; the number of readings required to fix the position of the curve is greatly reduced, interpolatiorr is easy and rapid, extrapolation can be carried out with greater confidence and, finally, the consistency of the measurements is readily estimated from the scatter of the points. The last advantage is particularly valuable when the data are obtained by direct microscopic examination alone, because they are influenced by the skill of the observer in estimating the relative size of areas, possibly also by undetected inhomogeneity of the specimen. A search for ways of representing the observations as a straight line yielded two methods which are described in this paper. The paper also includes an account of some interesting relations brought to light in applying these methods to the available experimental data. Usually the best way to derive such a method of plotting is to base it on established principles of chemistry and physics, as has been done, for example, for the temperature variation of the equilibrium constant of a chemical reaction. But so little is known of the mechanism of the decomposition of austenite, and so little is available in the way of well established background for changes of this kind, that it is simpler to rely upon purely empirical means. The general plan therefore is to study existing data with a view to finding some function of the direct observations that will

Jan 1, 1939