Search Documents

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By R. W. Gurry

In the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and III0°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon conteDt of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched, The mean result of concordant ments-—taeats-is-^that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C .(i755°F.) and 1.89 per cent at III0°C. (2030°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutec-toid temperature (738°C. or I360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature II35°C. (2075°F.) instead of the commonly accepted value of about 1.7 per cent. Experimental Procedure The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.' In the empty furnace the range of temperature over a distance of 4 cm. at the heat center was 9°C. (I6°F.) but at a given location the temperature remained within +o.5°C. (o.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (I760°F.) and III0°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with toluene; this quickly produced on the

Jan 1, 1942

By C. F. Wang

Page I. Introduction............:.............. 395 Manchuria in General ....................... 395 Pen-hsi-hu............................ 397 Pen-hsi-hu Coal & Iron Co., Ltd................... 399 I1. organization........................... 400 III. Coal Deposit........................... 402 Location..............................402 Geology............................. 403 Coal Mining...........'.................. 404 Mining Methods........................407 Mining Cost.........................408 IV. Coal Washing Plant.......................408 V. Coking Plant..........................410 VI. Iron Deposit...........................413 Magnetite Belt.......................... 413 Origin of Deposit......................... 414 Iron Mining........................... 415 VII. Concentration Plant........................ 417 VIII. Briquetting Plant.......................... 418 IX. Blast-furnace Smelting...................... 418 iNTKODtrCTION Manchuria in General Manchuria. called the "Three Eastern Provinces" in Chinese. forms the northeastern corner of China and is bordered by Siberia on the north and northeast. and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty. and in more recent times it has bcen an arena for diplomatic maneuvering and commercial competition between the Russians. advancing from the north. and the Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 1, 1918

By Alvin Kaufman

The industrial revolution of the early 1800's and the subsequent remarkable progress in raising American living standards are based not only on a constantly improving technology but on an ever increasing use of energy from mineral fuels and waterpower. Industrial nations require inexpensive energy sources in order to grow. The more complex the economy, that is, the more intensive the processing of raw materials, the greater the energy needs of that economy. As a result of the current international economic expansion, the worldwide search for sources of low-cost energy has accelerated. As a part of this search there is considerable interest in the potential for commercial development of geothermal power, particularly abroad and in the western United States. This interest is indicated by the fact that 40 exploratory wells have been drilled in the California thermal areas alone during the 1955-62 period. Of these, 24 were drilled in The Geysers, Casa Diablo, and Salton Sea areas.

Jan 9, 1964

A discussion at a joint meeting of the New York Section of the American Electrochemical Society and the American Institute of Mining Engineers, Nov. 20, 1913. Chairman Lawrence Addicks:-Our program this evening represents an attempt to set before you the present situation and outlook in the metallurgy of zinc. It is a time-honored custom to throw bricks at the zinc man. The accusation is that he has borrowed a lime kiln and a gas retort and part of a sulphuric acid plant, hitched them together, and spent the last 50 years in regarding with holy veneration the reactions which take place in that retort. The copper man, who thinks of zinc as something with which copper is adulterated to make brass, and the iron man, who regards it as a sort of paint for corrugated sheets, and the lead man, whose opinion as to zinc is not fit for publication, have long felt that, when two or three of the minor details of their respective metallurgies were put in order, they would take a few clays and fix up zinc on a modern basis. But somehow there still seem to be some unsolved problems at home, and while we are waiting it seems only fair that the case for the defense should be adequately presented. There is probably no man in this country to-clay better able to do this than Mr. George C. Stone, of the New Jersey Zinc Co., on whom I have pleasure in calling to talk to us on "Progress in the Metallurgy of Zinc." George C. Stone:-It is frequently stated that there has been no change in the metallurgy of zinc since the first Belgian furnaces were built in the early part of the last century. It is true there have been no such spectacular and radical changes as were worked in the metallurgy of copper and iron by the introduction of converters; but, in the essentials, I believe the progress in zinc metallurgy has been as great as in that of the other common metals. The main reason that there have not been revolutionary changes is that the chemistry of zinc differs radically from that of the other metals and these differences control the type of apparatus that can be used. The differences are: 1. The temperature at which zinc is reduced by carbon is much above the volatilizing point of the metal and it is therefore always produced as a vapor.

Jan 1, 1914

By C. D. King

DURING the 30-year period spanned by these annual Howe Memorial presentations, many lecturers could proudly claim a kinship either as a student or an associate of the man whose memory we honor. Although it has been my good fortune to have attended many of these annual lectures, it was not my privilege to have known Henry Marion Howe personally. However, his great repute as teacher and scientist was known to all undergraduates of my day and the later years have enhanced my appreciation of his wisdom and foresight. Those who knew him well have said he derived particular pleasure from speculations on the future world of metallurgy. For this reason, I feel that perhaps he would not be unsympathetic to a lecture in his honor which departs from the highly instructive scientific presentations made in the past by so many able Howe Memorial lecturers, and which is concerned more with the practical phases of various steelmak-ing processes and some speculations on their future form and relative importance. The word "revolutionary" is frequently applied to each seemingly important improvement in the production of steel ingots, but in retrospect these changes, impressive as they appear at the time, are merely steps of progress. In the hundred years from the inception of tonnage steelmaking, only three processes can be truly classified as revolutionary. They are the pneumatic process, known in this country as the bessemer process; the reverberatory method called the open hearth process; and, the electric furnace process. There have been many variations and combinations of the three fundamental methods, but they remain truly the only revolutionary methods in steelmaking since its early history. Everything else has been evolutionary, in effect. doing the same things that we have done in the past but doing them better, correcting our errors through experience, and slowly but inevitably reaching a higher state of accomplishment. It has often been said that coming events cast their shadows before, and the production of steel ingots is no exception. As a result of the unrelenting demands of World War I1 and the years that followed, truly impressive progress has been made in steel ingot production. The incessant pressure for immediate results during this period required the employment of initiative and daring, as in few past decades, and many developments were brought to fruition. Of equal importance is the possible effect on future steelmaking methods of the many ideas initiated but still in formative stages. Fig. 1 portrays ingot production in the United States by the three fundamental processes over a period of 75 years and is interesting because it poses some questions as to future trends. The early ascendancy of the bessemer, its replacement in importance by the open hearth process, the amazing growth of the latter, and the recent challenge of the electric furnace are evident from the chart. Management is fully aware of these changes, but is even more interested in the future trends. Our concepts of the relative importance of the more recent developments and their possible effect on future processes may perhaps be best exemplified by a specific, hypothetical problem. Let us assume management is contemplating a new ingot producing plant with an output of 100,000 net tons per month, located in an area where some purchased scrap may be obtained but where by far the largest component will be own-produced blast furnace iron. Management requires a process or combination of processes which will yield highly uniform quality characteristics in the ingot form, and represent the soundest selection in investment and operating cost. Under these conditions, the obvious selection for the past four decades has been the open hearth process but, in view of more recent developments, management may believe that it is no longer permissible to disregard other possibilities with impunity. Accordingly, to be assured of the best possible selection, they request that you review not only the possibilities of utilizing the conventional open hearth, duplex, bessemer, and electric furnace methods, but also the more recent developments, such as the turbo-hearth, the Linz-Donawitz method, the Perrin modifications, and other possibilities. With this background, one might then appraise the relative importance of these methods to meet a specific need, and concurrently speculate on the forms that future ingot processes will assume and the relative importance of these processes.

Jan 1, 1955

By Newell G. Alford

Forecasts of future timber consumption in soft-coal mining are handicapped by the lack of adequate experience records for estimating properly the timber requirements of the industry. Data were obtained from plants where records are kept or from operators who collected the information and to these were added composite figures for the continental United States in 1905 and 19191 and for central and western Pennsylvania and for Illinois in 1922.2 The result, representing slightly over 928,000,000 net tons, is shown in Table 1. Some of the companies furnishing data were unable to segregate the timber into classes of use but for those who did, Table 2 shows the board feet of posts and cross ban used per ton of coal mined and the percentage of the total timber consumed that was used in roof support. The wide variation in amounts of timber per ton of coal mined is the result of

Jan 1, 1924

By B. W. Frazier

At a recent meeting of the North of England Institute of Min ing and Mechanical Engineers, during a discussion upon the com pression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

By J. A. Herbst, R. Mackelprang, J. D. Miller

Droplet size distributions were determined by stabilizing in gelatin and measurement of the distributions by means of computerized image analysis Several variables that affect droplet sizes were studied and the resulting size distributions were modeled via a population balance equation Key parameters in the model were related to the physical properties and operating conditions of the systems examined using a multiple linear approach

Jan 1, 1981

By N. K. Chen, R. Maddin, K. T. Aust

Lattice rotations occurring on the tension and compression sides during the bending of molybdenum single crystals at room temperature were followed in detail. Observations were also made concerning crystallite rotations and slip traces. &apos;The results indicated the participation of (110) as slip planes and the<111>as slip directions. Crystallite fragmentation during bending was also noted. EVERAL investigations have been conducted on pure bending of face-centered cubic metals.&apos;-" Structural changes as a result of "bend-gliding," and the importance of bending and constraints during conditions of axial stressing, have been noted.&apos;," It was evident that the mechanism by which the bending deformation occurs is more complex than the case of simple shear. Studies of the bending of body-centered cubic metals from the aspect of the crystallographic mechanism appear to be lacking. Molybdenum single crystals therefore were subjected to deformation by bending in order to determine the reaction of the body-centered cubic lattice to bending stresses. It might be expected for the bending of single crystals that lattice rotation as represented by the axis of compression would proceed toward the pole of the active slip plane and that rotation of the tensile stress axis should indicate the slip direction.&apos; It was believed therefore that a study of the tension and compression sides of bent molybdenum single crystals should give data concerning the operative slip system. Specific problems which are pertinent to the overall picture of plastic deformation were also investigated, e.g., whether the constraints offered by pure bending give rise to the deformation band, and also the nature of the asterism occurring on the tension and compression sides during the stages of deformation. Experimental Procedure Eight single crystal specimens were grown from sintered molybdenum rods 143 in. diameter using the method described previously.6 The purity of this material was reported as 99.9 pct as described elsewhere.&apos; The specimens were % to 1/10 in. in diameter x 7 in. long, with single crystals approximately 1 to 2 in. in length occupying the entire center sections of each specimen. The specimens were elec-trolytically polished using an electrolyte of 300 cc methyl alcohol, 60 cc H2SO4, 130 cc HCl, and a current density of 4 amp per sq in. Each specimen was then loaded in a bending apparatus similar to that used by Yen and Hibbard,&apos; as shown in Fig. 1. The load was applied by means of a spring and screw arrangement through four ball-bearing surfaces set 1.5 in. apart. Either the inner two bearings or the outer two (A, B, Fig. 1) were attached to a movable steel plate (D) through which the load was transmitted. Since the apparatus was mounted on a track of the X-ray apparatus, the tension or compression side of the specimen could

Jan 1, 1954

By O. Knacke, H. Barth, W. Gans

The rate of cementation was determined by measuring the time required to consume a thin electrodeposited layer of the cementating metal as indicated by a sudden increase in the electrical potential. The diffusion controlled cathodic current of the more positive metal was measured by conventional electrochemical techniques and compared with the cementation rate under the same experimental conditions. Micrographs revealed different types of crystal growth in different surroundings e.g. dendritic growth in acidic solutions.

Jan 1, 1973

By William E. Ford, Edward Salisbury Dana

A. Anhydrous Carbonates The Anhydrous Carbonates include two distinct isomorphous groups, the CALCITE GROUP and the ARAGONITE GROUP. The metallic elements

Jan 1, 1922

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 &apos;poises&apos; times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 &apos;poises&apos; times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By Henry F. Hebley

This paper brings within the compass of one comparatively brief article a general description of the situation concerning the nation&apos;s water resources. It touches upon the phenomenal growth in the demand for water supply and emphasizes the problems facing the coal industry both with regard to acid mine water drainage discharged from active and abandoned mines and the suspended solids discharged to the stream system from wet coal preparation plants.

Jan 4, 1953

By Clintford R. Jones, Om P. Pande

This chapter presents a survey of instrumentation and control systems used on ball mill circuits from the past to the present. It is based on the concept of optimization of plant practice, and addresses the influence of the circuit design on the control strategy and on the instrumentation philosophy. Methods of optimization of the grinding circuit, within the constraints of the mill design requirements, are reviewed. The modern use of automation and circuit optimization is critically reviewed for known and possible conceptual control loops. A comparative study of circuit variations due to instrument hardware, location and installation is provided. Future trends i.e., computer control (DDC) and the effects on both the control stratagems and the optimization stratagems are described.

Jan 1, 1982

By C. A. Schempp

STUDY of the adaptability of Tintic Standard ores to concentration dates back to somewhat before January, 1921, when the chloridizing mill at Harold, Utah, was put into operation. The operation of this mill has been fully covered in the TRANSACTIONS (Vol. 73). The process consisted essentially of a chloridizing roast followed by a percolating leach with a nearly saturated solution of common salt, acidified with sulfuric acid; precipitation of silver on sponge copper, and of copper and lead on tin-plate cuttings. This mill was built to treat the low grade siliceous ores having an average content of

Jan 1, 1933

Upper Peninsula W. O. HOTCHKISS, Chairman C. H. BAXTER, Secretary-Treasurer, Michigan College of Mining and Technology, Houghton, Mich. S. R. ELLIOTT RUDOLPH ERICSON W. H. SCHACHT Utah Meets second Thursday of each month, October to May, inclusive B. L. SACKETT, Chairman C. T. VAN WINKLE, Vice-chairman G. L. OLDRIGHT, Secretary-Treasurer, U. S. Bureau of Mines, Salt Lake City, Utah A. E. RING L. A. WALKER

Jan 1, 1932

By Auguste J. Rosh

The use of titaniferous ores in the blast-furnace has been the subject of much controversy for many years. Divers objections have been raised against them, and, for one cause or another, the verdict

Jan 1, 1893

By J. B. Clemmer, F. D. DeVaney, H. A. Doerner

PRODUCTION of magnesium metal in the United States during the past decade has increased from less than 6oo,ooo lb. in 1928 to more than 4,800,000 lb. in 1938.1 The growing industry has stimulated interest in methods of production and in sources of raw material. All of the present domestic production is from brines. However, the availability of large tonnages of magnesite in the state of Washington, together with the possibility of cheap power, have created interest in the utilization of magnesite for the production of magnesium metal as well as for other purposes. Magnesite, the carbonate of magnesium (MgCO3), usually is associated with limestone (CaCO3) and dolomite (MgCO3CaCO3). It occurs in crystalline and microcrystalline (sometimes termed amorphous) forms.2 The more common crystalline mineral is found in various shades of white, gray, yellow and brown, the colors being due to impurities, chiefly iron. Magnesite has a hardness of 3.5 to 4.5 and a specific gravity of 3.0 to 3.1. It forms rhombohedral crystals in the hexagonal system, having a vitreous, pearly luster. The quarries and mines of the Northwest Magnesite Co. near Chewelah, Wash., are large producers of magnesite for refractories. The deposits are extensive, some veins being hundreds of feet wide. The boundaries of the veins are indefinite, and the magnesite is interfingered with dolomite. Calcite, talc, serpentine, quartz and shale are disseminated through the deposits. The quality of the ore cannot be determined by appearance or by simple tests; chemical analysis is required. These features make it difficult to determine the boundaries or total quantity of workable ore.3 Only the higher-grade ores are mined, and a considerable proportion of the magnesite content is discarded by hand-sorting and log-washing methods. After calcining, the sorted product meets the specifications for usual refractory material, as it contains approximately 81 per cent MgO, 7 per cent Si02, 6 per cent CaO and 6 per cent Fe203 + A1203. A sample of the reject material had the following analysis after calcining: 65.4 per cent MgO, 6.3 CaO, 21.1 Si02 and 6.5 R203. The percentage reported as R203 includes compounds whose chlorides are acid-soluble but give precipitates in ammoniacal solution that are ignited and weighed. The more common constituents are Fe203, A1203 and Ti02. The sorted magnesite product is not the best grade, even for refractory purposes, and leaves much to be desired for a reduction process. The rejected material contains a large proportion of magnesite. It is apparent that an effective concentration method would yield a higher recovery and a better product. In general, the refractory grade is not suitably pure for other uses. Recent developments in the production of

Jan 1, 1940