Search Documents

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By J. L. Walter

Tungsten ingots with and without small amounts of aluminum, silicon, and potassium were prepared by conventional powder-metallurgy techniques and hot-rolled to 0.001-in.-thick sheet. The ingots were rolled three different ways: I) initially cross-rolled, then straight-rolled; 2) straight-rolled, and 3) straig-ht-rolled, then cross-rolled. Total reductions were 99.8 pct. Samples of the sheet were annealed, in vacuo, at temperatures from 1200" to 2200°C. Substructures and textures were determined by transmission electron microscopy and X-ray diffraction. The doping agents were found to form particles of mullite (Al,Si,O,,) which, on rolling., appear to form strings of particles aligned parallel to the rolling direction. These strings of purticles are associated with an increase in the recrystal-lizution temperature from 1400°C for undoped sheet ThE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of drawn and recrystallized wire.'" The grains generally do not occupy the entire cross section of the wire and have lengths many times the wire diameter. The grain boundaries are, in general, nearly parallel to the wire axis and have long ''fingers" projecting one into the other as may be seen in Fig. 1, a longitudinal section of recrystallized doped wire. When unsuitable additions or no additions are made or the wire is not sufficiently reduced during draw- to 2000°C for doped sheet. The particles also limit lateral grain growth while allowing growth parallel to the rolling direction. This results in the formation by primary re crystallization of large highly elongated grains of specific preferred orientation. The undoped sheet recrystallized to small equiaxed gains. The preferred orientations of the large grains were determined from axis density plots to be (113) (691). (0i3) (362), (116) (304) types for the initially cross-rolled then straight rolled material. These orientations are similar to the orientations of the large elongated grains in doped and heavily drawn tungsten wire. The nucleation of the large grains appears to occur by recovery of certain of the polygonized regions of specific orientation, followed by strain-induced boundary migration.

Jan 1, 1968

By M. N. Short, I. A. Ettlinger

M. N. Short,? Washington, D. C., and I. A. Ettlinger, New York', N. Y. (New York Meeting. February, 1926) The Pioneer mining district, better known as the Superior district, from its principal town, is located in Pinal County in south-central Arizona about 80 miles east of Phoenix and 22 miles west of Miami. The region embraces a, confused series of mountain ranges of moderate height but precipitous slopes, between which lie irregular valleys filled with alluvial detritus. The average elevation is about 2800 ft. in the valleys and the summits of the ranges reach 2000 ft. above this. Superior is situated on the north bank of Queen Creek where it emerges from one of those ranges into a more or less basin-shaped valley. The drainage of Queen Creek is to the southwest and the flood waters spread out and lose themselves in the desert northeast of Florence, the county seat of Pinal County. The Magma copper mine (Fig. 1) is the only producer in the district. Although discovered in 1875, its production has been important only

Jan 1, 1927

By T. A. Rickard

RICO, in the southwestern corner of Colorado, is one of the productive mining centers of the San Juan region, so-called because its waters drain into the river of that name, which is tributary to the Colorado. The San Juan region includes the counties of Ouray, Hinsdale, San Miguel, Dolores, San Juan and Montezuma. It is traversed by a network of picturesque mountain ranges on whose lofty summits there rests perpetual snow. The region is peculiarly rugged, and, in the early days of its development, tested to the full the hardihood of the adventurers who first explored its can ions 111 search for gold and silver. A prospecting party, guided by Jim Baker, scout and trapper, penetrated in 1861 this part of the territory of Kansas. At that time the country was in the possession of the Ute Indians. In October, 1873, by the Brunot treaty, they ceded to the United States Government the richest mineral-bearing portion of their

Jan 1, 1897

G. K. BURGESS, ? Washington, D. C.-At the Bureau of Standards it was decided, in order to study the high-aluminum end of these curves, that efforts should be made to prepare pure aluminum, and the promise of getting aluminum, practically free from the two elements that have such great effect in very small quantities, namely, silicon and iron, and which

Jan 12, 1919

By S. N. Kesten, Richard Murphy, A. H. Land, W. F. James

Introduction—by W. F. James and A. H. Lang This paper describes the geology and present state of development of uranium and thorium deposits in Canada. It is expected that this information will be added to that now being assembled from available American and British data to provide a background for engineers and others who may be called upon in the future to examine or search for radioactive deposits. Some generaliza- tions regarding the Canadian deposits are included, but many of these are necessarily tentative. The information contained in the paper is up to date for the end of 1948. The information contained in this paper has been derived from many sources. Much of it is from the records of the Canadian government-owned Eldorado Mining and Refining (1944) Limited and from examinations of government and private properties made by officers of the Geological Survey of Canada. Some information on privately-owned properties has been quoted from other sources mentioned in the text. The information has been assembled by W. F. James of Eldorado Mining and Refining (1944) Limited and A. H. Lang of the Geological Survey of Canada, who have written the sections for which they are credited. The description of the Eldorado mine is based on reports by Richard Murphy, formerly chief geologist for Eldorado; the report by Mr. Murphy was published previously by the Canadian Institute of Mining and Metallurgy,' to whom the writers are indebted for permission to repub-lish. The section dealing with the geology of and development work in the Goldfields area, where Eldorado has important holdings, is by S. N. Kesten, field geologist for Eldorado. The geological diagram of the Goldfields area (fig. 2) was kindly supplied by A. M. Christie of the Geological Survey of Can-

Jan 1, 1951

By W. F. James, Richard Murphy, S. N. Kesten, A. H. Land

Introduction—by W. F. James and A. H. Lang This paper describes the geology and present state of development of uranium and thorium deposits in Canada. It is expected that this information will be added to that now being assembled from available American and British data to provide a background for engineers and others who may be called upon in the future to examine or search for radioactive deposits. Some generaliza- tions regarding the Canadian deposits are included, but many of these are necessarily tentative. The information contained in the paper is up to date for the end of 1948. The information contained in this paper has been derived from many sources. Much of it is from the records of the Canadian government-owned Eldorado Mining and Refining (1944) Limited and from examinations of government and private properties made by officers of the Geological Survey of Canada. Some information on privately-owned properties has been quoted from other sources mentioned in the text. The information has been assembled by W. F. James of Eldorado Mining and Refining (1944) Limited and A. H. Lang of the Geological Survey of Canada, who have written the sections for which they are credited. The description of the Eldorado mine is based on reports by Richard Murphy, formerly chief geologist for Eldorado; the report by Mr. Murphy was published previously by the Canadian Institute of Mining and Metallurgy,' to whom the writers are indebted for permission to repub-lish. The section dealing with the geology of and development work in the Goldfields area, where Eldorado has important holdings, is by S. N. Kesten, field geologist for Eldorado. The geological diagram of the Goldfields area (fig. 2) was kindly supplied by A. M. Christie of the Geological Survey of Can-

Jan 1, 1951

By J. P. Carson

THE Croton water-shed furnishes the source and storage of watersupply to both the old and the new aqueduct. The Croton river rises in the southern part of Dutchess county, about 68 miles from the lower end of New York city. Its three main branches, called the East, Middle and West branches, flow southward across Putnam county, joining, near its southern boundary, to form the Croton, which continues thence in a general southwest direction across Westchester county to the Hudson river at Croton Point, about 35 miles north of the city. The water-shed above the proposed site of the Quaker Bridge dam extends about 33 miles north and south, with an average width of 11 miles, making in all about 362 square miles, from which, by complete storage, an average daily supply of 250,000,000 gallons may be collected—sufficient for the needs of the city, probably, for the next fifteen years. The water-shed above the Croton dam is 23 square miles smaller, and furnishes the present daily supply of 100,000,000 gallons. By referring to the map it will be seen that the shortest approximately straight line between the proposed site of Quaker Bridge

Jan 1, 1891

By William E. Ford, Edward Salisbury Dana

The aluminate, ferrates, etc., allied chemically to the borates, have been already intro- duced among the oxides. They include the species of the Spinel Group, pp. 418-423, also Chrysoberyl, p. 423, etc. SUSSEXITE. In fibrous seams or veins. H. = 3. G. = 3.42. Luster silky to pearly. Color white with a tinge of pink or yellow. Translucent. Index, 1.59.

Jan 1, 1922

By T. Egleston

The necessity of using a refractory material capable of much greater resistance to chemical action and having a far higher melting-point than those which contain silica, which melt and sweat off in the furnace even when not exposed to bases forming with silica more or less fusible compounds, has led to a careful practical study of all those materials which contain very refractory bases. The results of these researches, extending over several years, and made on a very large scale in many of the largest works in Europe, are of the highest interest, not only considered as a step in the progress of the study of the materials themselves, but in the application of refractory materials to metallurgical uses in general. The result of the experience of the last seven years with these basic materials, as in general with all such substanccs, is that natural products cannot be used as such. They are either too uncertain in their quality, contain substances which may in certain cases be very injurious, or, when in a condition in which they might be used, are so rare as to become practically unavailable for employment on a large scale. The materials that may he used are therefore not only limited in number. but they must be prepared artificially. When the use of basic artificial material is further extended, no doubt the number of these substances will not only be greatly increased, but the methods of preparation will be both perfected and cheapened to such an extent as to permit their application in processes for which they have hitherto proved too expensive. The quantity of refractory materials required for making ingots will he from 130 to 150 Ibs. per ton, or between 6 and 8 per cent. of the metal produced. In an establishment producing 2000 to 3000 tons of steel per week, considerable space is required to handle the basic materials properly. It is proposed in this paper to briefly discuss these basic materials and their application in the only two metallurgical processes where they have as yet been applied. These are the basic Bessemer and the basic open-hearth process, known as the Thomas-Gilchrist processes.

Jan 1, 1886

By Frederick Laist, H. J. Maguire

The ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaccs, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper; this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it mas found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first- and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator produces a product that is self-fluxing; in fact, it is possible to produce a concentrate containing more iron than is necessary to flux the silica. Under these conditions, the amount of basic fluxing materials required for the smelting operations became very srnall and the converter slag lost its former value as a blast-furnace flux. For this reason, a less expensive method of recovering the copper, silver, and gold contained in it than smelting in blast furnaces had to be found. It was not feasible

Jan 1, 1921

By W. T. Roberts, N. G. Turner

A study of the fatigue properties of several grades of commercially pure titanium has established that the strain-aging process is of minor importance in the development of a fatigue limit and a relatively high fatigue strength ratio. Metallographic observations and damping measurements at room temperature indicate that striations are able to spread from grain to grain only at stress levels above the fatigue limit. This suggests that the fatigue limit represents the stress above which large-scale dislocation unlocking takes place. Fatigue tests on annealed material at - 60" and - 196" c showed that under conditions when a thermally activated diffusion process would be suppressed the fatigue limit is not eliminated. Prestraining at room temperature did not have a detrimental effect on fatigue strength at room temperature but a decrease was recorded at — 60°C. This is further evidence that initial dislocation locking is a important strengthening mechanism. TITANIUM and titanium alloys have S-N curves with a definite fatigue limit, and a high ratio of fatigue limit to UTS can be attained. Other materials which show similar fatigue characteristics are mild steel and some Al-Mg alloys. The fatigue limit of these materials has been associated with their strain-aging capacity. It is well-known that commercial-purity titanium contains interstitial impurities which can give rise to a sharp yield point, and a small strain-aging effect following static strain has been demonstrated.7 This type of aging reaction is differentiated from the dynamic aging process when aging occurs during plastic deformation, and which is generally observed at elevated temperatures. In a titanium at room temperature, dislocation locking is associated with the interaction of interstitial oxygen, nitrogen, and carbon atoms with dislocations. Ehr-lich has shown that the distortion produced by introduction of these atoms into the hcp lattice has no shear stress component and hence there is no interaction between the stress field and the screw component of a dislocation. Thus the dislocations as a whole are only weakly locked. It is clear that strain-aging effects in hcp a titanium will be much less pronounced than those observed in bcc iron and steel. In recent years, the attribution of the fatigue limit solely to strain aging has been questioned. It has been pointed out that a definite fatigue limit is observed at temperatures as low as -196°C in some titanium alloys,' and strain aging is not expected to be effective at this temperature. The role of initial locking of dislocations in determining fatigue behavior has been examined in low-carbon steel by Oates and Wilson. They showed that under conditions in which the aging potential is low the factors which control the buildup of local stresses and hence affect dislocation unlocking, e.g., grain size, are important. There are indications that other metals can have a definite fatigue limit with no established strain-aging capacity, an example being magnesium12 which has the same crystal structure as a titanium. The spread of plasticity from grain to grain in hexagonal metals may be more difficult than in cubic metals because of the limited number of slip systems in the former, and this may account in part for their fatigue behavior. The present work was undertaken to elucidate the relative importance of crystal structure, strain aging, and initial dislocation locking in determining the properties of commercially pure titanium when subjected to cyclic stressing. 1) EXPERIMENTAL METHODS Three grades of commercial-purity titanium were used and a material of lower interstitial content was prepared by melting high-purity Japanese sponge titanium (referred to as H.P. Ti). The compositions and typical mechanical properties of the materials are shown in Table I. Fatigue tests were made in push-pull (zero mean stress) using an Amsler Vibraphore machine at a frequency of about 160 cps. Two types of fatigue specimen were used—one with a waisted gage length for determination of S-N curves and the other with a parallel gage length for metallographic studies and damping measurements. After careful machining and mechanical polishing, all specimens were electropolished prior to fatigue testing. The electrolyte consisted of 10 parts methyl alcohol, 6 parts 2-butoxyethanol, and 1 part perchloric acid (SG 1.54) and it was maintained at a temperature of -10" to -20°C during polishing. Tests at room temperature were normally carried out with the specimen immersed in a silicone oil bath which could be heated for elevated-temperature tests.

Jan 1, 1969

By Eli T. Conner

My connection, under a commission from the Councils and Board of School Control of the city of Scranton, Pa., with a recent investigation of mine-caves and the resultant damages to surface-improvements, has led to the preparation, at the invitation of our Secretary, of the present paper. It is notorious that there are, in the anthracite-fields, frequent subsidences of the surface, due to the removal of the coal beneath. No particular attention is paid to such occurrences, unless they happen to injure surface-improvements. Many caves have happened in Scranton and its viciuity, which hare excited but little remark, since they have generally caused no serious damage. In August, 1909, a cave occurred in the Hyde Park section of the city, generally known as the West Side, which nearly destroyed school-house No. 16 and considerable adjacent property. Fortunately, there were no pupils in the building at the time; but the thought of the possible result, had the usual number of pupils and teachers been present, aroused the public to the gravity of the situation; and the School Board employed engineers to investigate the case. Two reports were made by separate sets of engineers, which differed in some particulars. These differences were pointed out in the public press and magnified, and the consequent agitation of the subject was taken up and greatly exaggerated by some of the metropolitan newspapers, giving to uninformed people the very erroneous impression that the whole city of Scranton was in danger of sinking into the bowels of the earth. All this tended to affect the credit of the city and to depress real-estate values. The matter was considered at a joint meeting of the Board of Trade, the Councils, and the School Board. The Hon. J. Ben. Dimmick, a former Mayor, suggested that it

Jan 1, 1912

By M. J. Marcinkowski, A. Szirmae, R. M. Fisher

Room -temperature hardness measurements obtained from single and polycrystalline samples of a 47.8 at, pet Cr-Fe alloy which were aged for various times al 500°C show a two-fold increase over that of the unaged alloy after annealing for 1000 hr. A detailed examination of the deformation markings in the neighborhood of the hardness imbressions reveals that twinning becomes an increasingly more important mode of deformation as aging proceeds. this observation is shown to be inconsistent with the Proposals that the transformation is eve of order-disorder On the other hand, the results are in agreement with previous observations of Fisher et al. of a coherent chromium-rich precipitate which forms in an iron-rich matrix as a result of a miscibility gap in this alloy system as proposed by Williams . Using the coherent precipitate hypotlzesis as a model, a detailed analysis of the various possible strengthening contributions to both the slip mid twinning stresses is made. In the case of' slip, lattice friction within the chromium-rich phase and the chemical energy associated with the interface between the two phases contribute about 60pet to the total strength. The contributions from coherency strains and modulus differences are thought to contribute the remaining 40 pet of the strength but are difficult to evaluate because of uncertainties regarding the flexibility of the dislocation line. All of the factors have nearly the same or else a smaller effect on the twinning stress in the aged alloy. Twinning is never observed in the unaged alloy because the twinning stress is much higher- than that for slip. With increased aging times, the various contributions to the total stress for both twinning and slip increase, but most of those for slip increase much more rapidly, so that, in the fully aged alloy, it surpasses the stress for twin propagation. When a twin is nucleated by the chance occurrence of an internal stress concentration during a test, the subsequent twin burst results in a low hardness reading. FeRNTIC Fe-Cr alloys from about 15 to 80 at. pet Cr content show considerable change in properties such as hardness, electrical resistivity, saturation magnetization, and so forth, after aging in the vicinity of 500°C.* The most marked change is a large increase in hardness accompanied by a sharp decrease in ductility, so the phenomenon has often been referred to as the 475°C (885°F) em-brittlement problem. Changes in microstructure are rather subtle and most investigators have not been able to observe any X-ray diffraction or metal-lographic changes during aging. There is little doubt that the phenomenon is inherent to the Fe-Cr binary system and is not directly related to the formation of a phase. Two distinct schools of thought have developed during the past decade concerning this problem. Masumoto, Saito, and sugiharal have concluded, from their own specific-heat measurements, that atomic ordering occurs in this temperature range. Pomey and Bastien2 have also attributed the changes in physical properties with aging in the neighborhood of 500°C to atomic ordering. In addition, Takeda and Nagai3 claimed to have found X-ray verification for superlattices corresponding to the compositions FesCr, FeCr, and FeCr3. However, all known attempts to observe superlattices in Fe-Cr alloys using neutron diffraction, which should be much more sensitive, have been unsuccessful. These have been reported by Shull et al.4 for 25 at. pet Cr, williams5 for 75 at. pet Cr, and Tisinai and samans6 for a 28.5 at. pet Cr. steel. The second and more prevalent opinion ascribes the 475°C embrittlement phenomenon to the formation of a coherent precipitate due to the occurrence of a miscibility gap in the Fe-Cr system below about 550°C. This latter concept was first indicated by the results of Fisher, Dulis, and Carroll,7 who were able to extract fine particles about 200Å in diameter from samples of 28.5 at. pet Cr steels aged from 1 to 3 years at 475°C. The extracted material was found to be nonmagnetic, to have a bee structure with a lattice parameter between that of iron and chromium, and to contain about 80 at. pet Cr. Williams and paxton8 and williams5 confirmed these results and first explicitly proposed the existence of a miscibility gap below the a region in the equilibrium diagram. Alloys aged within this gap

Jan 1, 1964

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By Clarence Zener

Contents Page General Principles................................................................. 551 Equilibrium Diagrams......................................................... 551 Nucleation................................................................... 553 Kinetics of Phase-boundary Propagation......................................... 553 Kinetics of Growth of New Phase............................................... 556 Spheroidization............................................................... 560 Pure Iron-carbon System........................................................... 561 Formation of Pearlite.......................................................... 561 Interlamellar Spacing........................................................ 562 Pearlite C-curve............................................................. 563 Bainite Formation............................................................. 565 Formation of Martensite....................................................... 570 Loss of Tetragonality of Martensite.............................................. 570 Effect of Alloys upon Decomposition of Austenite..................................... 572 Pearlite...................................................................... 572 Bainite and Martensite......................................................... 574 Time-temperature-transformation Curves............................................. 576 Appendix A............................................................. ......... 579 Appendix B....................................................................... 580 Appendix C....................................................................... 580 The present investigation started in an attempt to understand certain details of the decomposition of austenite, and of the effect of alloying elements thereon. As the investigation proceeded it became apparent that not only these details, but all the general features of austenite decomposition, could be understood in terms of fundamental physical principles. Since the direct applicability of these physical principles has not been previously recognized, it was decided to incorporate the original results of the investigation into a review of the general subject of the kinetics of austenite decomposition. This review constitutes the present article. An extended summary of the results is given on pages 576 to 579. This article, which deals with the kinetics of phase transformations, may appropriately be considered as a sequel to two recent articles1,2 from this laboratory on the equilibrium relations in medium alloy steels.

Jan 1, 1947

By Leslie F. Tedsen, John E. Dorn, Alan E. Flanigan

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By V. Jares

DESPITE the fact that a combination of metals-aluminum-zinc-tin, and sometimes aluminium-zinc-cadmium-is extensively used for aluminum solders, as well as for die-castings, the constitution of these alloys has not yet been made clear. I. BINARY SYSTEMS The system aluminium-zinc is the basis of the ternary alloys under consideration. Their composition was made sufficiently clear by the investigations of Roscnhein and Archbutt,1 Bauer and Vogel,2 Sander .and Meissner,3 Hanson and Gayler4 and Isihara.5 Only the temperature of decomposition of the crystals s seems still to be doubtful, whether it is considered as a compound of Al2Zn3 (according to Bauer and Vogel) or as an intermediate phase of variant composition (according to Hanson and Gayler). This temperature is given by most of the authors, as in the neighborhood of 256° C., only Isihara giving 280° C. As its accurate determination is of special importance in the study of the ternary alloys under consideration it was experimentally controlled in the following manner: An alloy corresponding in composition to the formula Al2Zn3 was made, in which the temperature effect was found to be the greatest. This was drilled and a silver-constantan thermoelement inserted into the cavity so as to be in direct contact with the alloy. The whole was then very slowly heated and the heating and cooling curves determined. The transition temperature from the heating curve was found to be 281° C., whereas-from the cooling curve it was 252° C.

Jan 10, 1926

By Alfred W. Gauger, George A. Burrell

The senior author of this paper, while in Colorado on other official business, made a trip to the Cripple Creek gold-mining district to get more data than are at present available regarding the composition of the gas that issues from the rock into the mines of the district. This was done at the suggestion of George S. Rice, Chief Mining Engineer of the Bureau of Mines. There are -many questions of interest and importance in connection with the ventilation of the mines in the Cripple Creek district, such as the menace to life and mining of a suffocating gas entering the mines from the rock, the danger due to powder smoke (from blasting operations), and danger of continued inhalation of rock dust by the miners. This report confines itself to the first problem, the gas from the rock, and principally to one phase of this question, the composition of the gas and its effects on men and lights. A more thorough study of this and other ventilation problems is planned. That the rock gas is a real menace is shown by the fact that miners (variously estimated from 25 to 50 by different persons interviewed) have been killed by it in the 25 years that mining has been vigorously carried on at Cripple Creek. Many men have had narrow escapes from death, some of them having been incapacitated for days. In addition, much loss of time results because at certain periods of the year or on certain days it is impossible to enter some workings. At a few mines, fans force air into the workings, thus supplementing the natural ventilation and much improving conditions, but the improvement is not entirely adequate at all times. Origin of the Gas Lindgren and Ransome1 think that the gas found in the rocks of the Cripple Creek mining district represents the last exhalations of the ex-

Jan 1, 1917