Search Documents

By E. M. Wise

IT is known qualitatively that the recrystallization behavior of platinum is dependent upon the amount and particularly the nature of impurities present, the amount of prior cold-work and the annealing time and temperature, but published data are limited. A study of the effects of cold-work and annealing temperature on the hardness of a sample of very pure platinum was undertaken to supply part of this information. CONCLUSIONS 1. The platinum used in the experiments had a probable platinum content of 99.99+ per cent, and had the following mechanical properties in the completely softened condition: Vickers hardness number, 39.4; ultimate tensile strength, 19,340 lb. per sq. in.; proportional limit, very low; elongation, 37.5 per cent in 2 inches. 2. The effect of cold-rolling on the hardness is shown in Fig. 1. The hardness increases rapidly up to 10 to 15 per cent reduction and more slowly up to about 75 per cent reduction, beyond which it increases more rapidly. 3. The recrystallization temperatures for a 15-min. anneal, after cold-rolling 19, 39.5, 50.8, 66, 80.5 and 89.5 per cent reduction in thickness, are approximately 765°, 700°, 635°, 600°, 545° and 425°C., respectively. 4. The recrystallized grain size of this platinum is a function of the percentage of cold reduction, being larger the lower the percentage of cold-work. 5. Little or no grain growth resulted from subjecting recrystallized samples to higher temperatures or annealing for longer times.

Jan 1, 1940

By Robert Mehl

IT has been shown that quenched iron of high purity exhibits a Widmanstätten figure much resembling martensite in appearance.1 This figure exhibits a maximum of four directions of the surface traces that characterize it, suggesting that a Fe forms from y Fe in plates parallel to the {111}, octahedral, planes in the y lattice. Because of this, and also because of the general similarity to the structural appearance of martensite and to the Widmanstätten figure obtaining in slowly cooled hypoeutectoid steels it has been suggested2 that the orientation relation-ships obtaining between the y and a phases in pure iron are identical with those demonstrated in martensite3 and in slowly cooled hypoeutectoid steels,4 and indeed that the crystallographic mechanism of formation of a Fe from y Fe is the basic mechanism determining the orientation relation-ships found in both martensite and in slowly cooled hypoeutectoid steels. This paper will present experimental evidence in support of this view.

Jan 1, 1934

ALABAMA Aldrich.-Lloyd, T. W. Anniston.-Carrington, F. G. Klugh, B. G. Bessemer.-Abbott, C. E. Dobbs, G. G. Ferguson V. Salmon, h. S. Stuart, Q. W. Birmingham.-Adams, J. H. Aldrich, T. H. Aldrich, T. H., Jr. Allen, A. W. Armstrong. W. D. Ball, E. M. Bonnyman, J. Bush, M. W. Carter, E. Crawford, G. G. Davis, C. B. Dryer. T. B.

Jan 1, 1923

By H. L. Gilbert, H. A. Johansen, R. G. Nelson

High purity electrolytic chromium plate has been hydrogen-reduced and arc-melted under inert atmosphere to give sound ingots. These ingots may be hot forged to break the as-cast structure and then worked at 500°C to finished form. An intermediate and final high temperature anneal gives best ductility and grain refinement. HE increasing interest in refractory metals for I use in high temperature gas turbines, jets, and rockets has led to great efforts in exploiting the fifth and sixth groups of transition elements. Much of the interest has centered upon production of metals that can be worked and fabricated by normal means to produce various engine parts or components having the high temperature characteristics of oxidation resistance and high creep strength required for such uses. If these pure elements do not exhibit all of the desired characteristics, it may be possible to obtain a high purity alloy that will. Since, in all cases, development of these transition elements has depended to a large extent upon removal of oxygen and nitrogen as a means for producing ductile metal, the hypothesis has been accepted that oxygen is the normal embrittling material in a high grade electrolytic chromium metal. Various methods have been employed in an effort to remove this oxygen by direct or indirect attack.' Many workers have endeavored to produce pure chromium through reduction of the oxide by carbon or active metals, while others have recommended fusion electrolysis of chromium salts or reduction of these salts by active metals, such as sodium or calcium. Hydrogen reduction of the oxide or chloride and thermal dissociation of the iodide have been reported to give high purity metal. Experimental Work The U. S. Bureau of Mines, Northwest Electro-development Laboratory, has systematically re-examined the more promising methods and developed two which produce metal having ductility at temperatures lower than heretofore described. It has been found' that oxide-free chromium chlorides in a NaCl-KCl carrier salt may be mag- nesium-reduced and the byproduct salts distilled off in vacuo to give a high purity chromium sponge. Fusion analysis conducted under the supervision of W. W. Horton of Knolls Atomic Power Laboratory showed the oxygen and nitrogen both to be below 10 parts per million on a selected sample. A small amount of carbon is carried over in the final metal from the chlorination and reduction steps which are carried out in graphite crucibles. This trace of carbon is not detrimental to hot ductility. A more practical method for producing ductile metal is through hydrogen reduction of high purity electrolytic chromium. Normal electrolytic chromium will, if "developed" for a few minutes at 1100°C in high vacuum, be found by the method of Adcock:; to contain about 1 pct chromium sesquioxide (Cr2O3). This small amount of oxygen may be effectively reduced by hydrogen.2, 4 The method employed was to crush electrolytic chromium plate in a gyratory crusher to pass 60-mesh; finer crushing appears to offer no advantage. A nitric acid leach removed the iron picked up during crushing. The leached powder was rinsed until neutral with distilled water and vacuum-dried.

Jan 1, 1954

By Mitchell, Edmund I.

VARIOUS suggestions as to proper fees for engineering services have been put forth by individual practitioners and by the American Institute of Consulting Engineers, the Connecticut Society of Civil Engineers, the Iowa Engineering Society and the Mahoning Valley (Ohio) Engineers, for the guidance of both the engineer and his client. The American Institute of Architects also has a schedule of minimum charges (revised 1908). So far as can be determined, however, the four national societies representing civil, mining, mechanical and electrical engineering have never given consideration to this question. An examination of technical periodicals published during the past decade shows that these schedules make provision for three methods of charging; i.e., (A) a percentage of the cost of the completed project; (B) a per diem rate; and (C) a fixed sum. Suggested minimum charges are as follows:

Jan 1, 1921

By F. B. Plummer

PETROLEUM ENGINEERING deals with the production, transportation, and refining of crude oil. Refining is chiefly the work of the chemical engineer; production, that of the petroleum engineer. Production engineering only is discussed in this paper. Petroleum production engineering is closest related to and, in fact, is a branch of mining engineering. Formerly, many petroleum engineers were trained as mining engineers or mining geologists. The profession is related also to mechanical and civil engineering to about the same extent that mining engineering is. Petroleum production draws upon the mechanical branch for drilling and pumping machinery and upon civil engineering for the construction of transportation lines, water supplies, and water-disposal plants. Fundamentally, petroleum production engineering deals with the removal of the oil from the reservoir rocks, just as mining is concerned with the removal of ore. The process of oil production demands a specialized knowledge just as distinct from mechanical and civil engineering as mining is distinct from operating a Diesel engine. Even though the chief tools of the petroleum engineer are the drill and the pump, these may be of little avail, and certainly not efficient, if their selection and use is not based on a knowledge of the physical chemistry of oil, the geology of the formations, the structure of the oil sand, the hydrodynamics of the reservoir, and the interrelation of all these many factors.

Jan 1, 1936

By W. C. Elli, M. E. Fine

YOUNG'S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,' is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.'. ' With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951

By M. G. Corson

THE theory of hardening by interference with slip which has been so clearly developed by Jeffries and his co-workers requires that an alloy to be amenable to age or heat hardening should contain among its components some that will stay in solid solution at high temperatures and precipitate as a secondary phase on cooling. This secondary phase may be either a more or less pure individual element (chromium in the case of copper, anti-mony in the case of lead), or some intermetallic com-pound. Those cases of hardening which depend on the precipitation of a compound are not only the most frequent, but are also far superior in the efficiency of hardening obtained. However, the slip interference theory as stated in its most general form is not sufficient to foretell new cases of this type of hardening and also will not explain some phenomena of a more intricate nature. It is not sufficient that a secondary phase might be absorbed by the main one at high temperatures and precipitated at the lower ones. The kinetics of this precipitation and the accompanying. physical phenomena of dimensional changes play independent and highly important parts. These kinetics, while not yet sufficiently studied to he formulated in the shape of physicochemical equations, might find their expression-in a qualitative systema-tization of the phenomena of precipitation according to two different viewpoints. To begin with, we encounter the question as to the velocities of the precipitation and of the growth of the phase precipitated. To harden a metal in an efficient manner we must be able to control the precipitation on one hand and also to bring the total of the secondary phase to such a number and size of the particles pre-cipitated as, will produce a desirable hardening effect under commercially feasible conditions of. age or heat hardening. From this viewpoint six different cases may be dis-cerned.

Jan 7, 1928

By L. S. Darken

IN the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be repre-sented satisfactorily by the simple equilibrium expression K - (p1)p1 (p2)p2 . (R1)r1(R2)r2 . where (P) denotes the concentration of a product and (R) the concentra-tion of a reactant in the reaction r1R1 + r2R2 + . . . Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a com-ponent is not proportional to its true mol fraction, But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple com-ponents and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satis-factorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature as ionization or the occurrence of polar and nonpolar molecules-are presumably less effective in metal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By Robert F. Mehl

THE mechanical behavior of metals and alloys is presumably conditioned by two factors; namely, the crystalline symmetry and the interatomic forces. Considerable attention has been given to the first of these factors through the recent advances in X-ray technique. It is the purpose of the present paper to call attention to the importance of the second of these factors, to point out promising methods of investigation, and to present some pertinent data. Plastic deformation takes place by slip along atomic planes.1 This slip may be inhibited in a number of ways: by the interatomic forces of cohesion which bind the atoms rigidly in a lattice structure, which in pure metals is usually of high symmetry; by lattice distortion caused by solid solution formation or by mechanical strain; by the intercrystalline boundaries where slip is restrained, probably by the non-registration of the atom planes in adjacent crystallites;2 and by the presence of small hard particles which serve to "key" the slip along the atom planes.3 In pure metals, and perhaps also in solid solutions, the atom planes of easiest slip are those exhibiting the greatest density of atomic population and the greatest interplanar distance4 and apparently can now be predicted from the analysis of the lattices. Concerning the interatomic forces, which resist this slip by holding the atoms firmly together, little is known. Most textbooks on physical metallurgy, following the work of Bottone,5 correlate the hardness of the pure metals with the atomic volume,

Jan 1, 1928

By T. Kilner, A. Plumtree

DURING an investigation of electro-deposited silver structures, samples were prepared for metallographic examination by cold mounting in plastic, grinding on successive grades of emery paper down to 3/0, and chemically polishing by swabbing using the chromic acid solution described by Gilpin and Worzala.1 Attempts to etch these samples using the standard solutions described for silver (e.g., 5 pet KCN-5 pet Na2S2O8, H2O2-NH4OH, and various potassium dichro-mate solutions) all failed to give good results due to staining of the samples and to rapid etching. The staining was caused by the chromic acid polishing solution being trapped in small fissures between the sample and the mounting plastic, and also in small fissures in the sample itself. To overcome these difficulties, an etchant was developed which prevented staining at the same time as it slowly etched the sample. This resulted in a very clean, crisply etched surface as shown in Figs. 1 and 2. This etch consisted of 10 ml of orthophosphoric acid, 10 ml of distilled water, and 2 drops of the polishing solution noted above,' which is made by mixing 100 ml of saturated CrO3 solution, 45 ml of 10 pet HC1 solution, and 800 ml of distilled water. The etching procedure involved taking the final polished sample, either immersing or swabbing in the etchant for a period of 1 to 2 min, rinsing as quickly as possible in distilled water, alcohol, and ethyl ether in that order, and then immediately drying. This etch is easily controlled due to its slow rate of etching, and produces samples with clean, sharp surfaces. Pits due to overetching produced varying contrast effects when viewed under polarized light, and are therefore obviously useful for revealing many structural details within the sample. Another effect of overetching was to produce a height varia-

Jan 1, 1968

By Richard P. E. Hermsdorf

IN the nonferrous sessions this year, magnesium wiggled its way into a dace of prominence such as it has never before enjoyed. This was evidenced not only by the number of papers presented on that metal but by the attendance at the meetings. The atmosphere permeating these magnesium meetings was similar to that which exists in a family with a new baby. Everybody crowded around to see what it looked like and then wondered whether it would be a success and credit to the family. Well. magnesium appeared to be a vigorous youngster, full of life, and raring to go. A close relative of maenesium named " aluminum, although much more grown up, also attracted much attention. From the activity and spirit in these sessions

Jan 1, 1944

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Charles T. Holland

Miners have observed for many years that as pillars are removed in mining operations the pillar adjacent to those mined out frequently shows evidence of being compressed. Although this has been known for a long time, little or no information is available concerning how far from the mining area the pillars are affected in this manner, or how great is the magnitude of the compression, or concerning the manner or characteristic way in which the compression acts, as the mined-out area approaches the pillar under consideration. The writer made a study of pillar action in the Mona mine of the Arkwright Coal Co., partly to get some quantitative data on the deformation of coal-mine pillars. The study was not completed but it seems best to present the information that was obtained. Method of Measurement Fig. 1 shows the details of the apparatus used for measuring the deformation. This is permanently attached to the pillar. Fig. 2 shows the details of the gauge that records the deformation. This gauge is removable and was used to measure the deformation at all the stations. The recording dial is graduated in thousandths of an inch and records measurements up to one inch. Fig. 3 shows how the removable gauge is placed in the instrument. When installing the instrument in the side of the pillar, all loose coal near by was removed and a trench 4 to 6 in. deep, and approximately 1 ft. wide, was dug in the pillar. In this trench near the top and the floor, the holes holding the instrument were bored. These holes were then partly filled with thin cement and the rods were inserted. The remaining space in the holes was tamped full of cement. At this time, by carefully manipulating the permanent rods and clamps and adjustable pin, it was possible to adjust the instrument so that the removable gauge would stand true and measure any vertical deformation between the top and bottom rods. Fig. 4 is a photograph of one of the instruments installed, showing the removable gauge in place.

Jan 1, 1938

By Gerhard Derge

A SERIES of studies of the corrosion of tin is under way in the Metals Research Laboratory at the Carnegie Institute of Technology. The complete program includes examination of the corrosion properties of high-purity tin and the changes produced in these properties by the addition of varying amounts of alloying elements. Other studies of this subject have been made recently under the sponsorship of the Inter-national Tin Research and Development Council, but these researches have been confined largely to the weakly acid environments commonly encountered in the canning industry.1 There is little information avail-able regarding the corrosion of tin under alkaline conditions, but such data would be of value, for a large amount of the metal is used under such conditions. The potential measurements to be described were made because they seemed to offer the most rapid method for obtaining a general view of the conditions to be encountered in such service. These experiments will also serve to establish a technique that will be of value in further studies. It must be emphasized that the results reported are those of controlled laboratory experiments and that the conclusions drawn cannot yet be applied to service conditions; rather, they point to the directions in which, more exhaustive experimental work may be clone to best advantage.

Jan 1, 1938

H. Van F. Furman, Denver, Colo. (communication to the Secretary): There are some statements in Dr. Carpenter's interesting paper which appear to require explanation, if not modification.

Jan 1, 1901

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselman Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo. 12. Chaco River area, N. M. 13. Lewis and Thurston County fields, Wash. For two of these areas; the Paonia field, Colo., and the Coosa field, Ala., we have published recently preliminary reports, and final reports are in preparation. In addition, we are nearing completion of a coal reserve study of Montana, and are beginning similar studies in several other states, as part of a program of revising our estimate of national coal resources on the basis of presently available data. Factors Involved in Making Estimates Our responsibilities include detailed field mapping to secure information on areas of outcrop of coal beds, their range in thickness, nature of roof rock, amount of overburden, correlation of the beds, stratigraphy and structure of the coal-bearing rocks, and the preparation of coal reserve figures based on these data. The computation and estimation of resources of coal in the ground, like that of resources of other mineral commodities, involves consideration of many additional purely geological factors that can be appraised best through such regional studies. Regional variations in the thickness and texture of rocks overlying and underlying coal beds, for example, give evidence as to the probable position of the edges of the basin of coal deposition, or may aid in the delineation of sand-filled channels that sometimes cut out coal beds. It is apparent that the detailed field studies, in which data are gathered, are the basis for coal reserve studies, and in our present program these two phases of work are being carried on together. Previous Coal Reserve Estimates For many years we have been aware

Jan 1, 1950

[59H1-Water Law and Its Significance to the Mining Industry by Wells A Hutchins 59H2-Relation of Land Subsidence to Groundwater Withdrawals in the Upper Gulf Coast Region, Texas by Leonard A Wood and A G Winslow 59F3-Hydraulic Mining of Gilsonite and Its Application to Coal Mining by J H Baker 59H4-Recovery of Phosphates by In Situ Fluid Mining by Sylvain J Pirson 59F5-Coal Cleaning Plant Design for Minimum Operating Labor by Wm M Bertholf and John D Price 59F6-Coke Combustibility A Neglected Characteristic by J D Price 59B7-Union Carbide's Uranium Operation at Maybell, Colorado by K W Lentz and F T Temple 59H8-A Rapid Method for Estimating Alumina in Feldspathic Sands by Hugh H Bein 59H9-Water Laws as Related to Dredging in Idaho by Robert A Lothrop, Richard B Porter, and Robert P Porter 58B19-Separation and Washing of Alumina Process Residue by Morton Handelman 59B11-Feed Preparation and Froth Modification for Fatty Acid Flotation by Carl C Martin and Burt C Mariacher 59B12-Design Requirements for Tailing Disposal in the Southwest by E Vern Given 59B13-Semi-Dome Shaped Buildings for Bulk Storage by Edward E Ives and William L Payne]

Jan 1, 1961

By AIME AIME

AN enthusiastic crowd, cheerfully confident that the upturn in the oil industry has arrived, gathered in Los Angeles on Sept. 29 for a Petroleum Division meeting arranged by the Southern California Section. The assembly room of the California Oil and Gas Association was the place of meeting. H. Norton Johnson was in the chair for the morning session, with about eighty members and guests present. Four papers were presented before lunch and a fifth, on electrical coring, was withdrawn as the work on which it was based is still confidential. Joseph Jensen read his contribution on the "Kettleman Hills Middle Dome Unit Plan" and, as he had an active part in framing the plan, his outline and discussion of it was authoritative and informing. J. H. Woods asked concerning the operation of the casing-head gasolene plant under the plan and was informed that one company would operate the plant and royalties would be paid participating companies

Jan 1, 1933

By J. C. Fisher, J. H. Hollomon

The fundamental problem concerning the fracture of both crystalline and noncrystalline solids is the divergence between the actua1 and the theorcticallY computed fracture stresses; the stress required for fracture, computed from the forces between atoms, is many times that actually observed with commcrcinlly available materials. Computatiolls have been made,,2 indicating that the theoretical fracture stress should be from 100 to 1000 times that actually observed. There are other incidental problems that have arisen, perhaps the most importallt of which is the problem of size effect often observed in the measurement of the fracture stress of non-metallic solids, such as glass. Another effect conccrns the relation between deformation and the stress required for fracture, Experiments recently made with pearlitic steels indicate that the tensile fracture stress increases with increasing tensile deformation and decreases with increasing prior com-pressive deformation, This marked ani-sotropy of the effect of deformation on the fracture stress is in contrast with the essential isotropy of the flow stress. Early experiments on rock salt crystals by Joffe, et al.3 have illustrated the effect of tensile strain in increasing the tensile stress required for fracture. A consistent theory must be constructed that will explain not only the divergence, of the measured fracture stress from the theoretical value, the size effect, and the ergence of deformation; but will also explain and predict the effects of combined stress, of temperature, of strain rate, and of metallurgical structure. With respect to this last variable, it has now been relatively well established that the carbide particle is the clement of structure controlling the fracture of steels. In steels carbide particles vary in shape from plates to spheroids. It has been found that not only docs the magnitude Of the Fracture stress depend upon the size and shape of these particles. but also its dcpendencc upon strain is affected by changes in 'hap' an' size Or the particles. The precipitate resulting from the age hardening Of duralumin also modifies the fracture stress of this alloy. Nonmetallic inclusions greatly lower the fracture stress of all metals. The magnitude of the lowering depends 0' the size and shape of the included particles. In glass, the major source of the low fracture stress has been fairly conclusively demonstrate' by Griffith4 '0 arise from real flaws or cracks present in the material. He showed that the stress concentration at the end of a defect was of suficient magnitude to raise the stress at this location to a value comparable with the theoretical strength Of the material. If the cracks were reduced in size, Griffith showed that the observed fracture slrength the by virtue Of the decrease in stress concentration. He also pointed out that cracks disposed perpendicularly to the applied tensile stress would be more effective in lowering the fracture

Jan 1, 1947