Search Documents

By C. S. Smith, K. K. Ikeuye

In an earlier paper1 one of the authors called attention to the significance of the relative free energies of grain boundaries and interphase boundaries in alloys in determining the shape and distribution of micro-constituents. The ratio of the interphase and inter-crystalline boundary energies (that is, —?12, where ?12 is the energy of the interface between a crystal of phase 1 and a crystal of phase 2, and ?11 is the energy of the boundary between two crystals of phase 1) will be denoted by F. It is this ratio that determines, by the simple triangle of forces relation, the dihedral angle, ?, of phase 2 where it adjoins a boundary between two grains of phase 1. On a metallographic sample various angles are actually obtained because of the random orientation of the plane of observation, but the statistically most frequent angle is the true one. These basic principles were discussed in detail in the earlier paper. The experiments described below show the effect of both composition and temperature on ? and T for some alloys containing a liquid phase, and provide data on the rate of approach to the equilibrium angles in both solid and liquid phases. All the alloys were melted in a graphite crucible and cast into ingots 3/4 by 11/8 in. cross-section. Some of the aluminum alloys consisted of two immiscible liquids from which uniform castings could not be obtained. The amount of liquid phase varied locally to a considerable extent and the analyses were meaningless. Nevertheless, the composition of the liquid would not differ from that in an alloy of the intended gross composition, and the synthetic composition of the alloys was therefore used in considering the surface energy results. The ingots were given initial deformation by cold-rolling to 50 pct reduction, annealed, and given a second 50 pct reduction prior to cutting into small samples for heat treatment at the times and temperatures subsequently reported. The resulting micro-samples were carefully prepared metallographically and examined at magnifications of 650, 1280, or 2500. The objectives used were 21X, 0.40 NA (dry); 41X, 0.65 NA (dry); and 80X, 1.40 NA (oil emulsion). The appropriate angles were measured by rotation of the stage of a Bausch and Lomb metallograph to align the appropriate boundaries successively with a cross-hair in a micrometer eyepiece. About 250 angles were measured on each phase. Though the angles were read to 1°, the accuracy is probably not above 3°, because of uncertainty in setting the cross-hair tangent to the sometimes curved boundary. The corners of very small particles, particularly in early stages of adjustment after cold-rolling, were difficult to measure and the results were slightly dependent on the magnification used (compare Fig 1-C and 1-D). With particles of larger size and more nearly equilibrium shape, magnification made no difference (vide Fig 1-F and 1-G). The measured angles were grouped in 10° intervals (5° if ? was less than 20°) and plotted in bar

Jan 1, 1950

By Colin J. Dixon

The full realization of the potential of computers in geological in- formation system demands new approaches to the machine representation of information. At the same time, the feasibility of such a system, particularly in commercial field, demands greater freedom in input preparation and a degree of standardization in the arrangement of subject matter system. The paper describes some of the basic notions of project "GEOSEMANTICA 70". The aim of the project is to devise means of storing real geological informations in a machine rather than the representation of the information in human language form. This is seen as the only long-term solution to the problems of the complex vocabulary of geology and the complex syntax of geological description. Effectively, a machine language is being defined, consisting of a set of symbols and a date structure for representation of geological and related information. Beyond this, is the definition of a set of rules allowing the use of constrained text as an input/output medium. The investigation is oriented primarily to the representation and handling of information about mineral deposits and the associated geographic, economic and engineering information.

Jan 1, 1969

By Henry A. Wentworth

(New York Meeting, February, 1912.) ELECTROSTATIC separation of ores in its present form is generally known as the Huff' process from the name of Charley H. Huff, of Boston, Mass., through whose constant and persistent labors (with the invention of Clinton E. Dolbear as a basis) the successful commercial process embracing separative machinery and the various electrifying devices has been developed step by step, and the finances for the long period of development provided, and the method finally established and recognized throughout the world as an important and successful addition to the ore-dressing department of metallurgy. The permanent field-success of electrostatic separation began in 1908 with a 20-ton Huff experimental mill built specially for the purpose by the American Zinc, Lead.& Smelting Co., in Platteville, Wis., a plant which was a success from the start and was gradually increased in capacity as the market-conditions warranted to 100 tons of concentrates per day. Much credit is due to the above-mentioned company for its initial venture, and for its assistance in applying the process to field use. Prior to 1908 electrostatic separators had been installed and operated (but for a comparatively short time, however) in a number of places; some under the patents of Mr. Dolbear by himself and associates, and some under the patents of Lucien I. Blake and Lawrence N. Morscher, by W. G. Swart, mining engineer, of Denver, who has always been a courageous advocate of electrostatic separation. Due to the difficulties experienced in the generation of the electrical charges, the primitiveness of the separators, the wooden construction instead of iron as at present, the lack of control of the electrical fields and other difficulties overcome by the later inventions of the Huff Electrostatic Separator Co.,

Jun 1, 1912

By K. Sallmann

Spurred by a variety of factors, coal flotation is making headway among the preparation plants of West Germany. The author gives some statistics on German coal flotation plants and information on the properties of the feed and quality of the derived products. Types of machines and reagents used, dewatering practices, tailings disposal, and thickening operations are covered. There is special emphasis on the many-sided problems that confront German coal preparation engineers. The coal mining industry of West Germany is concentrated in three coalfields: the first on the Ruhr and the Rhein rivers, the second on the Saar river, and the third near the frontier between Germany and the Netherlands, around the towns of Aachen and Erkelenz. The total run-of-mine production of these three coalfields amounts to 736,000 tpd which come from 145 collieries. There are 121 washeries, 43 of them with a flotation plant. The total throughput of these 43 washeries is 280,000 tpd, out of which 26,000 tons (9.3 pet of the washery feed coal) are cleaned by flotation. The capacity of the individual flotation plants varies within relatively wide limits, the average being 40 tph and the capacity of the largest flotation plant being 120 tph. During the last few years, the number and size of flotation plants have been steadily increasing, although flotation must be looked upon as an expensive and rather complex cleaning process. The considerations which have led to the widespread application of flotation may be summarized as follows: 1) In making coking coal, it is seldom possible to add uncleaned fines to the coke oven charge, as their ash content is too high. If, however, the ash content of the fines is reduced to a maximum of 7 or 8 pet, they can be admixed to the washed and crushed small sizes without difficulty. This means, naturally that revenue is increased since the price of coking fines is always higher than the price for dust or uncleaned wet fines. 2) To prevent silicosis and pneumoconiosis, water infusion and spraying of the coal are practiced much more today than ever before. As a result, moisture content of run-of-mine coal has markedly increased and the washery feed coal contains more and more slurry instead of dry dust. The price of slurry, how- ever, is very low, and in many cases it is impossible to sell filtered raw slurry with a moisture content of 20 to 25 pct and, at the same time, 20 to 25 pct of ash. Reduction of the ash content of these slurries improves the possibility of dewatering them and, in this way, also enhances the marketability of this product. 3) The new severe laws and regulations against pollution of air and rivers make it necessary to de-dust coal better than in the past and to reduce the quantity of the waste water from coal preparation plants and their solids content to a minimum. 4) Even if there were no compulsory reasons to clean the fines, flotation will often lead to an increase in the overall yield. Although not the only application, it appears that the treatment of coking fines is the primary field for the flotation process in coal preparation. It must not be overlooked, however, that a series of arguments may be advanced against flotation: 1) Flotation is an expensive process because, in addition to the cleaning operation itself, the dewatering of the froth and the disposal of the tailings is very costly. 2) Operation of a flotation plant requires well trained personnel. 3) Filtered froth has about a 20 pct moisture content and, therefore, if mixed with the cleaned small coal it causes an undesirable increase in water content of the coke oven charge. For this reason it is necessary to take additional measures for dewatering washed small coal and this, of course, entails additional expense. 4) Disposal of flotation tailings involves very difficult problems, particularly in the highly industrialized regions. An investigation covering 32 flotation plants of Western Germany shows the following composition and properties of their feed:

Jan 1, 1961

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y', and E carbonitride has been confirmed and it has been found that y' is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part' reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,' this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* 'Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,' obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969

By JOHN A. MALONEY

AS noted in the February issue of MINING AND METALLURGY, an advisory committee to the Museum of Science and Industry of Chicago was authorized by the Institute's Board of Directors, with W. R. Wright of Chicago, former Director of the Institute, as chairman. Since that time the committee has been undergoing organization, and held its initial meeting at the Museum offices in Chicago on April 11 and 12. Functioning as consultants to the Geology and Mineral Industries branch of this new institution, the advisory committee is aiding in building an exhibit which will tell the story of geology, mining, and metallurgy to millions of visitors a year. Although patterned to some extent

Jan 1, 1932

By Robert L. Clayton, Arthur Baker

Two massive sulfide zinc-copper ore bodies are in quartz-sericite schist (probably formed by regional metamorphism of sediments) and andesite of the Precambrian Yavapai Series, on opposite sides of a large rhyolite mass. The Copper Queen ore body is conformable with bedding of its schist host rock, but the Old Dick ore body probably crosscuts the strata. A lens of low-grade mineralization in chlorite schist, associated with the Old Dick ore body, crosscuts through 150 feet of strata. The ore bodies are almost entirely enclosed by premineral faults with less than 150 feet of displacement. The minerals of the ores are pyrite, sphalerite, and chalcopyrite, with minor arsenopyrite and galena and small amounts of intimately associated chlorite, sericite, and calcite. Old Dick sphalerite-chalcopyrite intergrowths have mutual boundaries, and sphalerite grains contain abundant exsolved chalcopyrite. Copper Queen sphalerite-chalcopyrite intergrowths have extremely ragged boundaries, the sphalerite contains no exsolved chalcopyrite, and the ore overall has a schistose texture. The pre-mineral fault on the hanging wall of the Copper Queen ore body has had 100 feet of post-mineral displacement. Wall rocks of the Old Dick ore body locally have been sericitized. Andesite and quartz-sericite schists for at least several hundred feet around both ore bodies have been chloritized erratically and contain traces of copper.

Jan 1, 1968

By R. F. Mehl, C. E. Birchenall

SINCE Maxwell1 first considered the self-diffusion process in 1872 its importance in the kinetic theory of matter has been recognized. Until the discovery of isotopes in 1913, a direct measurement of this quantity seemed impossible. The only information that could be gathered indirectly was for gaseous systems for which the kinetic theory was well developed. When methods of direct observation be-came available, investigations on self-diffusion were carried out in condensed phases. In metals these data are presumably of potential importance in the study of recovery, recrystallization, creep, sintering, and related phenomena. Following the pioneer work of Von Hevesy2 and his collaborators, who determined the rate of self-diffusion in lead with the naturally occurring thorium B isotope, several metals have been investigated. Pb, Ag³, Au.6,5, and Cu6,7,8,9 are examples of isotropic crystals existing in only one phase modification. Anisotropy of diffusion has been demonstrated in Bil6 and Znll. This paper is a study of a single metal in two allotropic forms and also of self-diffusion in a body-centered cubic lattice. Despite the fact that the measurements in each of the papers cited on self-diffusion in copper seem to be internally consistent to about 10 to 15 pet, the curves reported by different authors differ by factors of 2 to 4 at the same temperatures. This uncertainty may account, in part, for the failure to establish a successful correlation between the self-diffusion rates and other physical characteristics of the metals. No satisfactory theory of metallic self- diffusion has as yet been proposed to account for all the existing data and to permit estimation in other metals. Experimental Part: Two units of radioactive iron were used in these experiments, each a mixture of Fe53 and Fe59 (12). Fe53 decays by K electron capture and the emission of an X ray with a half life of about 4 years. Fe59 emits two beta spectra, one with a maximum energy of 0.26 Mev, the other 0.46 Mev, and gamma rays of 1.1 and 1.3 Mev, with a half life of about 44 days. They were present in nearly equal concentration initially. The composite half life started at about 50 days and increased as the Fe59 decayed, leaving Fe55 relatively more abundant. After aging a year, the half life was too long to measure significant decay in a month. The absorption properties also changed with time. Because of the importance of the absorption coefficient in the diffusion calculations, it was necessary to determine this quantity frequently over the period during which these experiments were carried out. This correction was unsuspected at the time of publication of notesl3 on this work and accounts for the discrepancy in alpha iron and for part of the discrepancy in gamma iron.* * The data in the present paper supersede those given in the notes entirely. In one note the scale of log D was inadvertently reversed. In addition to the correction for the drift in absorption coefficient, the D values for gamma iron at low temperatures were high owing to insuficient correction for diffusion occurring during heating and cooling through the high temperature part of the alpha range at a rate much slower than that employed in the runs reported here. The high temperature alpha rates are much higher than the low temperature gamma rates and correspond to large equivalent times at these temperatures. These experiments were discarded and new measurements taken. Independent experiments with the same activity units indicated a radioactive contaminant in the iron, but exhaustive attempts to isolate and identify it chemically failed. These experiments? indicate † These experiments will be discussed in a later publication from this laboratory. that the contaminant represented only a trace of little importance in the diffusion results. The active iron was plated from an iron chloride solution. Enough of the solution was dropped on a 1% in. square of filter paper to wet it thoroughly.

Jan 1, 1951

By P. E. Fitzgerald

ACIDIZING, as the terns is used in the petroleum production industry, involves the use of hydrochloric acid in predominantly limestone formations, resulting in the lowering of resistance offered to the flow of oil and gas through the oil-bearing formation, usually with resultant increased production. A number of articles have been written on the chemical treatment of oil and gas wells; a bibliography of these works will appear in Volume 123 of the Institute's TRANSACTIONS (1937), and a few other references are appended to this paper.

Jan 1, 1937

By H. N. Treaftis, J. W. Cahn

THE previous determinations of the solvus of tin in solid lead disagree with one another by as much as 40°C or almost 10 at. pct. Even determinations that appear to be careful differ considerably in both the solubility and its temperature coefficient. Recent kinetic workl -3 on the rate of precipitation of tin from lead-tin alloys and thermodynamic work4 on the heat of solution of tin in lead have given some insight into the time necessary to reach equilibrium in this system. As this time is longer than that used in almost all previous determinations of the solvus, these determinations are questionable. Since the interpretation of recent kinetic results requires accurate values of the equilibrium solubility the present work was undertaken. DISCUSSION OF PREVIOUS RESULTS The methods used in previous studies may be placed into three classes: 1) Several alloys covering a range of compositions are allowed to reach "equilibrium" at a certain temperature.5-7 Some property, such as the X-ray lattice parameter of the lead-rich phase or the re- sistivity of the alloy, is then measured as a function of composition. The solubility limit for that temperature is taken to be that composition at which a discontinuity in the property occurs. However, the recent kinetic work has shown that tin precipitates in two stages. The first stage is rapid but leaves the lead still supersaturated. The second stage is very slow, and it seems from the equilibration times quoted by the investigators of the solvus that the end of the first stage of precipitation was usually mistaken for equilibrium. This is especially true at temperatures below 100°C where the first reaction is still quite rapid (from minutes to months), but where the second stage is so slow that very long holding times are required to reach equilibrium. Alternatively micrographic work8 on several alloys of different compositions seems to have given good results if done carefully. 2) The beginning of precipitation in a homogenized alloy is measured as it cools slowly8-10. Since reactions in solids undercool easily, such determinations will always give too low a temperature for the solvus. 3) Some property of an alloy is measured as a function of temperature while the alloy is above the solvus.5,9,11 The range of temperature can usually be extended slightly into the two phase region. Then the alloy is precipitated at a much lower temperature and slowly reheated. The solvus is taken to be the lowest temperature where the property of the reheated alloy is equal to that previously determined for the homogeneous alloy. Usually one also expects a discontinuity at the solvus in the temperature variation of the property for the reheated alloy. The difficulty in this method is the sluggishness of the dissolution process, and this method may give too high a solvus temperature. EXPERIMENTAL The phase boundary or solvus temperature was determined by a modification of method 3 for a series of chemically analyzed high-purity alloys, ranging from 5.1 to 26.4 at. pct Sn. The resistance, as a function of temperature, of a sample of homogenized alloy (which could easily be undercooled) was compared with the equilibrium resistance which that alloy sample attained after precipitation at room temperature followed by long isothermal anneals at various temperatures. Before each anneal the sample was rehomogenized and reprecipitated. The solvus temperature could be located to within 1°C as the intersection of the resistance vs temperature curves for the homogenized and equilibrium alloys. No attempt was made to locate the phase boundary more accurately since the limiting factor was the precision with which the alloys could be analyzed. This precision was ±0.1 wt pct Sn and corresponds to an error of 1 deg in temperature. This use of isothermal anneals differs from some of the previous investigations in which method 3 was used with baths of slowly rising temperatures. It was found early in the investigation that solvus temperatures tended to be high if the latter method was used even at extremely slow heating rates. For example a

Jan 1, 1961

By A. B. Parsons

AN often repeated criticism of the profession of engineering is that it is as a whole it lacks solidarity. organization, co-ordination, and leadership. Significantly, the critic, are all engineers. Other members of the body politic either do not know about the absence of organization or they do not care. If engineers have no organization they have a plethora of organizations. There exist in the United State, today some 350 societies. institutes. clubs, associations, and councils of engineers and engineering technologists and this number excludes several hundred local chapters of national societies. trade associations, and local engineers' clubs of purely social character- Successful engineers must be proficient in analyzing, planning, and co-ordinating. but it is generally admitted that for their profession as a whole their success in this respect has been indifferent.

Jan 1, 1943

By John Garcia

THE presence of carbon de terre along the banks of the Illinois river was noted by the members of the Joliet and Marquette expeditions in 1673, and that may be referred to as the birthday of coal in the Middle West. The march of progress in the majority of indus-tries radiating from Chicago-one of the phenomena of history-is due in no small measure to this same carbon de terre and to the development and exploita-tion of the vast coal resources, which nature in a generous mood spread so lavishly over almost the en-tire state. The geological records indicate that coal-bearing rocks underlie three-quarters of Illinois, in-cluding 85 of the 102 counties and the entire area is estimated at from 36,000 to 42,000 square miles. Not all of the coal in this great area may be mined under the conditions existing today; producers are now taking the "cream" since industry demands the best quality and the lowest cost, thereby forcing competition among operators, which, in turn, com-pels the development of mines in those areas where the coal may be most readily .won, leaving the coal that is more difficult and expensive to mine to pos-terity. This is not such a bad arrangement, since the engineers of succeeding generations will enjoy the advantage of the experience of their ancestors, where-by they should profit and know how to mine a 2-ft. seam with as much economy and dispatch as we today work coal of thrice that thickness. During the period between 1830 and 1850, Illinois coal-mining progressed from the art of scratching along the outcrop to the development of small mines, mostly slopes, drifts and shallow shafts, but the real progress in the industry was coincident with the con-struction of railroads.

Jan 2, 1927

By S. D. Dahlgren

ORDERED G.P. zones having the cesium chloride structure were found to exist in the bcc iron-rich grains of an Fe-Au-Cu alloy that had been supersaturated with approximately equal atomic percentages of gold and copper, and aged at 400° and 350°C. Streaks and superlattice spots in electron diffraction patterns revealed the presence of the ordered zones in the aged material. The ordered Ll2 structure is commonly found for precipitates in fcc metals (e.g., Ni3A1 in nickelL7') but it is uncommon to find precipitates in bcc metals having the cesium chloride structure. The formation of the G.P. zones caused age hardening of the grains. Samples containing 3.8 at. pct each of gold and copper (with the remainder being iron) were annealed at 95@ or 1125°C in quartz capsules and were quenched by breaking the capsules under water. X-ray diffraction patterns revealed two solid solutions in the quenched samples. One solid solution was bcc and the other was fcc. The microstructure consisted of iron-rich grains of 0.3 mm diam surrounded by a yellow gold-copper-rich grain boundary network. The Au-Cu phase diagram %hows continuous solid solubility of gold and copper with ordered phases forming below 410°C. None of the ordered Au-Cu phases have the cesium chloride structure. Both Fe-Au and Fe-Cu phase diagrams3 show extended miscibility gaps and only terminal solid-solution phases. Consequently, it is reasonably certain the iron-rich grains consisted of an a-phase terminal solid solution, and the grain boundary network consisted of a gold-copper-rich terminal solid solution. Lattice parameters of the quenched solid solutions were consistent with the suggestion that the quenched phases were terminal solutions. The lattice parameter of the bcc phase (2.879A) obtained upon quenching from 950°C was higher than that (2.866A) for pure iron. The fcc phase in this sample had a lower lattice parameter than that for a 50 at. pct Au and 50 at. pci Cu solid solution, i.e., 3.866 compared to 3.877A. The lattice parameter for the 50 pct Au and 50 pct Cu solid solution was interpolated from data for Cu-Au solid solutions.4 More gold and copper were soluble in iron at 1125°C than at 950°C as indicated by a 0.012A increase in the bcc lattice parameter for a sample quenched from 1125°C. After the alloy had been quenched from 950° and 1125°C, the bcc lattice parameters were 2.879 and 2.891A1 respectively G.P. zones having the cesium chloride structure-which formed during low-temperature aging—were detected by electron diffraction and observed with electron transmission microscopy. In Fig. 1, the asymmetrical streaks parallel to ( 100) directions indicate that platelike G.P. zones had formed parallel to (100) planes of the matrix. The direction of streak asymmetry shows that the bcc unit cell of the G.P. zones was larger than the bcc cell of the matrix. The ordered cesium chloride structure is indicated by low-intensity superlattice spots at 010 positions which are nonallowed for bcc structures. The superlattice spots are streaked; therefore they are from the G.P. zones and are not caused by rel-rod effects of a thin matrix phase. The appearance and size of the zones observed in electron transmission microscopy and the appearance of the asymmetrical streaks in the electron diffraction patterns for the Fe-Au-Cu alloy were the same as those observed for a similarly treated Fe-Au alloy.' Ordered G.P. zones were detected also for an Fe-Au-Cu sample aged only at 400°C. The production of the ordered cesium chloride structure zones by low-temperature aging of super-

Jan 1, 1968

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By Dick Whittington, W. R. Taylor

GENERAL In mid-1974, a representative of ARCO Petroleum Company walked into our Austin offices and asked for a permit for ARCO's first Clay West Mine site. This was the first in situ uranium mining permit issued in the United States. That initial permit, issued in January 1975, was for three acres. The four years since have been characterized by growth and change. Today there are 16 permits approved for approximately 1,540 production acres issued to five companies at eight sites in four counties. There are approximately seven additional permit applications being processed or on the verge of being submitted for an estimated 2,000 additional acres of production. As a rough gauge of the financial scope of this activity, at the typical 40 production wells per acre and an estimated $2,000/well, operators hale installed or committed $122 million for production wells. This does not account for the exploration and development wells installed to delineate the ore or the cost of processing facilities for extracting the uranium. HISTORY OF URANIUM MINING IN TEXAS Information I have concerning early in situ uranium mining activities is "sketchy" but the apparent first on-site test of in situ uranium mining was conducted between 1967 and 1971 at the Dueterstat site, north of Yorktown in Gonzales County, by City Service. Others ran tests at the Bruni site in Webb County and the Burns and Clay West sites in Live Oak County in the mid-70's. During this period, Texas Water Quality Board personnel in the central and district offices maintained a general surveillance of these various test activities. Regulation of in situ uranium mining was formalized with the issuance of a permit in January 1975 with the advent of ARCO's initial production scale (3 acre) effort in the Clay West area at the Moser mine site. Since 1975, the accelerating rate of mining and exploration activity is noticeable. There were 16 exploratory rigs operating early in 1977. This year, the rig count is averaging 46--a 287% increase. HISTORY OF LEGISLATION Paralleling this mining activity was state and federal legislation which subjected in situ mining to environmental regulation. The following is a brief chronology of the legislation that is directly or indirectly related to uranium mining. As most of you know, disposal wells are an integral part of most in situ uranium mines operating in Texas. They are used both during production and during aquifer restoration following production. The wells are regulated by the Texas Injection Well Act, enacted in 1961 by the Texas Legislature. In 1967, the Water Quality Act established the Texas Water Quality Board, and provided for the regulation of water quality by the so-called permit system. In 1969, the Solid Waste Act was enacted by the Texas Legislature. The legislation provides for control of wastes from manufacturing, mining, and agriculture. This Act regulated uranium surface mining activities until 1975 when the Texas Surface and Mining Reclamation Act placed responsibility with the Railroad Commission for uranium open-pit mining and surface mining of coal and lignite. In 1972, the Federal Water Pollution Control Act (Public Law 92-500) was passed. This legislation forms the legal base for the NPDES (National Pollutant Discharge Elimination System) and the subsequent point source effluent guidelines and standards. The November 6, 1975 issue of the Federal Register published interim final rules for Best Practical Treatment levels for effluent discharges from ore mining and dressing operations. Litigation was immediately initiated by eleven companies against these proposed rules, and they are currently being reconsidered for reissuance in 1979. In 1974, the Federal Safe Drinking Water Act (Public Law 93-523) was enacted. A part of this legislation is the Underground Injection Congrol Program. The regulations implementing this program have undergone various public hearings and it is expected that they will be published in the Federal Register before the end of 1978. In 1975, the Texas Surface Mining and Reclamation Act (Senate Bill 55), providing for the Railroad Commission's authority to require reclamation of surface mines, was passed. In 1977, an amendment to Senate Bill 55 was introduced that proposed to place regulation of in situ mining of coal, lignite, and

Jan 1, 1979

By John D. Price

R. W. Campbell (Jones and Laughlin Steel Carp., Pittsburgh)—As usual John Price has presented an excellent paper. I know of no one who has devoted more time and conscientious thought to this subject than he has, and his efforts have produced scientific data and conclusions of real value. Results of similar studies made by the Jones and Laughlin Steel Corp. on the blending of Pennsylvania coals may be of interest. During 1935 the late F. W. Wagner and the present writer developed an empirical physical fuel value formula for evaluating the combined physical tests of metallurgical coke, see Table IV. In the development of the formula, the tumbler test, shatter test, screen test, and porosity of coke have been taken into consideration. Each of these tests brings out some physical property not expressed by the others, and in estimation of the importance of these tests as a medium for evaluating coke for the blast furnace, their worth has been graded as follows: It was thought that some additional penalty should be applied to cokes that do not show a uniform screen size, assuming that coke larger than 4 in. was not desirable and that this size was an indication of irregular size. Therefore the screen test factor is further corrected by applying a penalty of 1 pct for each 1 pct material greater than 4-in. size as shown by the screen test. The physical fitness of coke for blast furnace use depends upon four fundamental characteristics: l—gen-era1 strength, as indicated by the shatter test; 2— abradability, or the resistance of cell walls to reduction in size by attrition, as indicated by the tumbler test; 3—porosity; and 4—size and uniformity. Each of these characteristics is not of equal importance, but surely, in an attempt to determine an accurate physical value, the individual value of each should be taken into consideration. The formula is used as a yardstick, so to speak, in determining variations in the normal production of metallurgical coke and in making comparisons between normal coke and experimental blends with other coals. Table IV gives results of coking tests on raw and washed high volatile coals and these same coals with blends of coke breeze, anthracite coal, char and low volatile coals, all from Pennsylvania. The table also gives the source of the coals and coke breeze, as well as their proximate analyses. It will be noted that the washing of the raw high volatile coal increased the physical fuel value from 26.17 to 39.16, showing the effect of removing shale and slate which produces a detrimental fracturing and weakening of the coke. It is a well known fact that many Pennsylvania high volatile coals contain an excess of resinous material or binder which has a tendency to weaken the coke, owing to its high evolution of gases during carbonization. Tests were therefore made with coke breeze, an inert material, in an attempt to alleviate this condition. Blends of washed coal with 5 pct and 7.5 pct coke breeze collected from the coke plant quenching sump (82.9 pct through 1/8-in. screen) resulted in cokes with a physical fuel value of 20.75 and 16.73 respectively, lower than results obtained from 100 pct raw high volatile coal. It will be noted that the percentage of + 4-in. coke increased but that the tumbler test was very low. Undoubtedly better results could have been obtained if the coke breeze could have been crushed extremely fine. During World War II the government asked the coking industry to consider the use of anthracite coal as a substitute for high quality low volatile coal, which was extremely scarce at the time. The next series of tests was made with blends of raw and washed high volatile coals and 5, 10, and 15 pct Pennsylvania No. 5 buckwheat anthracite (100 pct through l/8-in. screen). It was necessary to use some raw high volatile coal in these blends because of insufficient washer capacity at the time. It will be noted that the physical fuel values

Jan 1, 1954

By GLENVILTE A. COLLINS

(Presented at a Meeting of the Spokane Local Section of the Institute, Feb. 17, 1912, and accepted for publication in the Bulletin. ) WHILE I am not at the present time engaged in active mine-management, my duties permit of extensive study and examination of many mines, mills, and reduction-works in various places throughout the United States. Being much interested in efficiency-work in general, and an ardent reader of writings on this subject by Frederick W. Taylor and others, as applied to manufacturing-plants, and having served my apprenticeship from mucking to the engineering design of ore-dressing and underground plants, I hope that this paper will lead others to investigate the field more fully, to the improvement of general mine- and mill-operations, as well as the advancement, intellectually, physically, and financially, of the employee and his relations with the employer. If a man who is prepared to look closely and observe broadly starts in Canada and zig-zags from camp to camp to southern Mexico, taking time casually to inspect mines, mills, and smelters, he will be pitifully impressed by the great difference in customs, and the general waste of labor, time, and money throughout the country. He will so seldom observe a dollar's worth of results given in exchange for a dollar spent that he will form a poor opinion of operating-efficiency and management. This highly-scientific department, requiring an amount of skill and executive ability equaled in few, if any, of the professions, certainly falls short of the standard established in our greater manufacturing industries. It is easily said that this is due to the diversity of conditions in mining, milling, and smelting. But on second view it must be admitted that there is room for tremendous improvements in nearly every mining-organization. The proposal of such improvements is often met by the argument that any mine

Sep 1, 1912

Jan 1, 1896

Jan 1, 1924