Search Documents

"Located in Madison River Canyon, about 14 miles by road from Norris, Mont. Built in 1907 by Madison River Power Co.DAM: Rock filled wooden crib structure, 183 ft. long, 34 ft. high or 44 ft. to top of flashboards.SPILLWAY: 140 ft. long, equipped with flashboards 10 ft. high.PIPE: One 10-foot and one 12-foot wood-stave pipe, 7,515 feet long.PRESSURE: One pressure chamber, 32 ft. high, 30 ft. wide and 81 ft.CHAMBER: long, built of concrete.PENSTOCKS: 4 9-foot steel penstocks about 200 ft. long, one for each wheel.WATER WHEELS: 4 double horizontal, center discharge, Sampson special 44-inch turbines, 3,600 h-p., at 100 ft. head. Speed 300 r. p. m„ direct connected to generators.GENERATORS: 4 G. E., W. C., 2,250 k-w., 4,000 volts, 300 r. p. m., 3 phase, 60 cycles, alternators, with exciters mounted on same shaft.TRANSFORMERS: 12 G. E., W. C., 900 k-w., 60 cycles. High tension voltage 23,100, 34,650, 46,200; low tension voltage 4,000, 3,800, 3,600. Now operating at 46,200, delta connected. They can be connected Y for 40,000, 60,000 or 80,000.OPERATION: This is the principal plant of the whole system and carries most of the load."

Jan 1, 1913

By R. F. Slack, J. C. Draper, J. A. Younkins

In 1959, the Duquesne Light Co. was faced with the problem of moving more than 40 million tons of bituminous coal in Greene County, Pa. The coal had to travel a distance of about 4 ½ miles from a new mine portal in Rocky Run Valley to the company preparation plant and loading facilities on the Monongahela River. After careful study of this immense transport problem, Duquesne decided that the belt conveyor system described in the following pages offered the best solution. This system, now in operation, is probably one of the four or five longest permanent overland conveyor systems in existence. The general layout of the entire system is shown in Fig. I. A detailed description of the salient features of the system is presented below. THE MINE The valley of Rocky Run where the system begins is very, very narrow and very steep. It was chosen as the site of Duquesne's new mine portal because it was the only place on this particular property where the Sewickley coal seam cropped out. The valley also had two other advantages. First, it fronted on a state road and, second, it offered a site where some 4 million gallons of water could be stored for use in dust-allaying sprays needed in the mine. The company elected to construct a drift mine in the valley because this would require neither the hoisting time of a shaft mine nor the walking time of a slope mine. As part of the mine construction project, the valley was leveled by relocating its stream and filling its center with material cut from each side.

Jan 11, 1966

By L. C. Graton

Although marked by numerous well-known attributes of its own, gold does not possess a kind and range of physical, chemical and geological characteristics wholly different and apart from those of other metals. Instead, it is merely one of the family of metals, with its individual and distinctive traits subordinate to the underlying family relationships and resemblances. The geologist concerned with pure science will pursue, therefore, the same general course and will examine the same broad kinds of facts and interrelations when studying the occurrence of gold as when studying that of copper or cadmium, or any other metal. But when we come to consider the use and economics of the metals, we discover that gold differs strikingly from all the others. Gold, in short, is unique, not by virtue of its inherent characteristics, but because of a peculiar and concerted psychological regard in which it is held. It will be evident, therefore, that the geologist who would deal with gold supply must give far greater weight to economic considerations than is required in his contacts with any other metal. If the geologist be called the scientist of occurrence, and the economist the scientist of use, the economic geologist stands as the necessary link between them. Perhaps it is in part because the economic geologist has made himself more familiar with the science of occurrence than with the science of use and has thus in some degree failed to bridge effectively the gap between the two fields, especially with regard to gold, that the usen1 of gold now appear to be in a state of general concern and even of alarm for the security and adequacy of future supplies. In the case of no other mineral commodity do the users, as a rule, trouble themselves greatly about the adequacy of supply except in so far as that may affect the price which they shall have to pay for the commodity. Oversupply, with resulting low price, they regard as a gift of good fortune. As to long-term undersupply, they are generally content to go ahead on faith, leaving the producer to discover as best he may the means for meeting their requirements or the inventor to find a substitute. But history has shown that for gold a different situation exists. While

Jan 1, 1931

By G. S. Cole, G. F. Bolling

Fluid flow strongly influences ingl structure and the columnar -to-equaaxed transition. Artificial flow patterns siwzilar to the nuturul ones act to induce this transition, while dampening forces act to suppress this transition. It is shown here how simple mechanical forces can be applied to a systerrz in order to induce or slipPvess relative fluid flow and the change both the structure transition and the exact structures obtained. The example used is the effect of slow rotations and oscillations 012 a cooling- ingot (of laboratory scale). The details of rotution and oscillation for various cooling rates, lenlperal~ire gradients, and sizes of ingot are related to other solidzfication variables. THE grain structure of a casting can be changed by altering the fluid motion during solidification. Just how important these changes are depends directly upon the degree to which the fluid motion can be controlled. An early step in understanding the nature and influences of fluid motion was taken by studying natural thermal convection; when a static mechanical device was used to suppress natural flow the result was opposite to that obtained when an electromagnetic device was used to augnlent flow in a pattern similar to the natural one. ''2 Suppression allowed more columnar growth to occur, but "augmented natural convection" brought about an earlier columnar-to-equiaxed transition (CET). Since the solidification of a free ingot must have characteristics somewhere between those displayed during suppression and augmentation, we know that natural convection must influence the CET. Further, since heat transfer in the liquid is always some time-dependent combination of convection and conduction, it can easily be guessed that the temperature gradient in the liquid is the vital factor affecting the CET.1,2 It is obvious that the structure arising from the unadulterated solidification of an ingot, without external influence, is rarely if ever the best possible one. Although the pattern of the natural fluid flow may be considered efficient, the magnitude of the flow and the heat transfer decrease freely from the outset. For a

Jan 1, 1968

US 4,134,618-Method for restoring an underground reservoir subsequent to the solution mining of an ore body of uranium, copper, nickel, vanadium, molybdenum, silver, rhenium, or selenium. Clean water a cycled through the mined area, via the injection and production wells used during mining, at a flow rate sufficient to entrain residual dissolved solids. The solids are separated at the surface and disposed of, e g., in a deep disposal well, while clarified water is recycled C A. Kossack, assigned to Atlantic Richfield Co. Jan 16, 1979 4 pp. (299-5) Filed. 12-29-77 (865,646) US 4,155,982-In situ leaching of a subterranean uranium ore deposit The ore is leached with a dilute aqueous solution of ammonium bicarbonate containing a small amount of hydrogen peroxide in order first to convert tetravalent uranium in the ore to the hexavalent state and second to dissolve the hexavalent uranium preferentially to the other metals or elements commonly occurring In such ore The uranium- enriched leach liquor IS brought to the surface, and the uranium recovered by means of adsorption on a particulate ion exchange resin, elution with an acid, and treatment with ammonia to precipitate relatively pure ammonium diuranate. G G. Hunkin, T P. Fife, and J R Stano, assigned to Wyoming Mineral Corp. May 22, 1979. 13 pp (423-7). Filed: 10- 9-74 (51 3,445). Same: Canadian 1,027,849, dated Mar. 14, 1978. US 4,157,847-In the mining of sulfur by the Frasch process hot water accumulating above subterranean sulfur from previous mining operations is recycled downward to contact and heat additional solid subterranean sulfur. Advantageously, pressurized and superheated drive water from above ground is commingled with the underground water to raise its temperature before it is recycled downward R. L Williams, R L Latiolais, J. L Gabriel, and R. L Bouis, assigned to Freeport Minerals Co June 12, 1979. 13 pp (299- 6) Filed 7-28-77 (81 9,879). US 4,158,76%1n this method for determining the uranium content of a solution obtained in the solution mining of an underground uranium ore deposit, the intensity of gamma radiation from the Th-234 daughter of U-238 emitted by the solution is determined as it impinges on a scintillator after being passed successively through filter foils of a ytterbium- tin alloy, a lutecium-tin alloy, and a hafnium-zirconium alloy This scintillation is evaluated as a measure of the uranium content To assure that the uranium-thorium conversion has reached a stable state, the measurement should be made about three months after the uranium solution has been produced R C Smith, assigned to Westinghouse Electric Corp. June 19, 1979 11 pp. (250-255). Filed. 10-20-77 (843,770).

Jan 1, 1980

By H. M. Hobart

THIS paper deals principally with investigations undertaken by the Welding Research Sub-committee of the Welding Committee of the Emergency Fleet Corporation. The general object of the investigations has been to extend the use of welding in the construction of merchant ships and, specifically, to provide a definite basis for obtaining the best economy and efficiency in employing welding in place of riveting in the construction of the hulls of such ships. Composition of Ship-plate Steel The chemical composition of the steel employed in such hull construction varies with the thickness of the plates. Through the courtesy of Mr. H. Jasper Cox of Lloyd's Register of Shipping, the following information may be given concerning the kind of steel plate employed in American Shipyards in 1918 for the hull construction of merchant ships. Lloyd's requirements do not relate to the chemical composition. They require a tensile strength of 58,000 lb. per square inch (40.75 kg. per sq. mm.) for their lower limit and 72,000 lb. per square inch (50.59 kg. per sq. mm.) for their upper limit. For the information of the Committee, Lloyd's obtained from their surveyors at various works data of the carbon content, which is as follows:

Jan 2, 1919

By Earl R. Parker, Ralph Hultgren

DURING the past year publications in physical metallurgy have not been abundant when compared with the output of prewar years. Nevertheless, some noteworthy contributions have been made to the literature. Because of the necessity for war production, much of the metallurgical effort has been directed towards the solution of problems of production processes. The limited amount of time devoted to other problems is reflected in the small number of papers devoted to nonapplied research, though a few excellent contributions have been made to the fundamentals as will become evident in the following pages. Results of many of the government-sponsored research investigations have been released to the public and are being published in the technical journals. Many more of these papers may be expected to appear in the 1946 publications.. Public distribution of information obtained in the course of these investigations should be of great value to American industries in the postwar era. Continued activity in research of all kinds is apparently assured because of intense

Jan 1, 1946

By C. A. Hansen

INTRODUCTION It has been the experience of the writer, during some. five years' work with electrolytic zinc, that the zinc cell is perhaps more- sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulphate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities. and cumulative impurities derived from the leaching of the ore; it also in

Jan 3, 1918

By C. A. Hansen

Page Introduction............................206 Power Characteristics in Zinc Sulfate Electrolysis........... 207 Current Efficiency......................... 207 Corrosion Rates..........................216 Voltage Required by the Zinc Cell..................219 Power Requirements of the Zinc Cell ................221 Impurities in Zinc Electrolyte.....................222 Non-cumulative Impurities.....................223 Cumulative Impurities ....................226 Impurities in General........................228 Temperature and the Stability of the Zinc Cell..............229 Practical Expedients for Control of the Zinc Cell...........234 Acknowledgments...........................234 Appendix................................235 Discussion...................:.......... - 236 Introduction It has been the experience of the writer, during some five years' work with electrolytic zinc, that the zinc cell is perhaps more sensitive to impurities in the electrolyte than the analytical methods as yet developed for the chemical identification and determination of these impurities; but that, when proper purification methods have been applied to a given solution, the behavior of the cell is quite independent of the original sources from which the zinc sulfate has been derived. It has also appeared that the behavior of the zinc cell is the best and surest check on the correctness and thoroughness of the purification methods used, because it indicates the presence of both current impurities and cumulative impurities derived from the leaching of the ore; it also indicates whether these impurities are current or cumulative, at least in so far as they are of serious importance commercially.

Jan 1, 1919

By Ferit Gurses

EXTENSIVE coal and lignite deposits exist in Turkey. Bituminous coal is the nation's principal mineral resource; important not only as fuel for the industrial development of the country, but also as a means of obtaining foreign exchange. Of the electrical power generated during 1939, 82.8 per cent was derived from coal.1 It is anticipated that the lignite deposits will be one of the major sources of power for the electrification of the country. BITUMINOUS COAL The locations of the four principal bituminous-coal2 basins are indicated on Fig. 1. The Eregli-Zonguldak basin lies on the Black Sea northwest of Ankara; the Canakkale basin lies near the junction of the Dardannelles; the Trakya basin is in European Turkey northwest of the Bosphorus and the Erzurum basin lies far to the east. The Eregli-Zonguldak basin is the most important of the four. This coal basin was discovered in 1829 but did not arouse interest until 1848; up to 1865, its annual production had not exceeded 50,000 metric tons. In 1865, during the Sultanate, working of coal mines was started by the Navy department, and the annual production was 61,145 metric tons. In 1908, the Minister of Commerce and Agriculture was authorized to develop the whole coal basin. Production reached 264,397 metric tons in 1910, and during 1915-1922, preceding the revolution, the total production of the basin was 2,676,043, or an average of 334,000 metric tons annually. The period of national revolution that followed was marked by a steady increase in coal production in Turkey, although world production decreased, because of the crisis of 1929-1932, about 52 per cent. AREA AND GEOLOGY OF THE COAL BASIN The geology of the Eregli-Zonguldak area is not yet completely known. The basin begins at Gungazi, to the west of Eregli, and extends to Sogutozu, a distance of about 106 miles. The coal beds, however, appear only in places and the overlying Cretaceous strata hide them elsewhere. This area includes the most important centers, such as Kandilli, Alacaagzi, Teflenli, Kozlu, Gelik (see Fig. 2). The geological sequence of the district is correlated with the Cretaceous of the Balkans; which is, in turn, a prolongation of the Alpine zone. Geological surveys made by G. Ralli, R. Zeiller and P. Arni3 show that the Eregli-Zonguldak formations fall into three natural divisions. Series a, The Alacaagzi in the district of that name (Fig. 2), is of the Culm stage. The strata strike generally east-west and dip about 30° south. This series appears also around Kandilli and Camli, with a steeper angle of dip, but the deposits there lack regularity. The Alacaagzi stage appears also farther east, to the south of Kozlu and Gelik. The Alacaagzi series contains 15 seams of an average thickness of 2 ½ ft. of good coal. Series b, the Kozlu, best represented in Zonguldak, Kilimli, Catalagzi, and between

Jan 1, 1944

By Richard H. Hopkins, R. W. Kraft

A new technique facilitating the rapid determination of the three-dimensional morphology of phases suspended in an opaque matrix is described. The vapidity of the technique is based upon continuous cinephotomicrographic recording of specimen microstructure as the specimen surface is removed under controlled conditions in an electrolytic cell. The advantages of the technique for determining spatial morphologies in opaque materials are illustrated by application of this method to the study of the configuration of faults in a specimen of directionally solidified CuAl2-Al eutectic alloy. A spatial model of the eutectic fault network deduced in this manner has substantiated the facts that faults in this alloy tend to lie parallel to one another in a direction close to that of the specimen growth axis and that the majority of faults tend to bridge lamellae rather than run parallel to them as growth proceeds. For the specimen studied fault density decreased as growth proceeded. ALTHOUGH metallographic observation is a powerful tool for investigating the correlation between structure and properties in metallic alloys, ordinary metallographic methods suffer the fundamental limitation that any conclusions concerning the three-dimensional structure of these opaque materials must rely upon inference from two-dimensional microsections. For this reason it is frequently impossible to make valid judgments regarding the true spatial distribution of the micro-constituents in specimens under investigation. Several techniques have been devised to circumvent the basic limitation of planar microsec-tioning and employed with varying success. These include construction of three-dimensional models of alloy microstructure from sequences of photomicrographs,1-3 quantitative deduction of spatial features based upon statistical studies of data from random and/or selected plane microsections,4-6 and selective dissolution of one phase in a two-phase alloy to reveal the topography of the phase remaining.' However these techniques also have certain obvious disadvantages. Construction of three-dimensional models is a very time-con- suming procedure due to the tedious polish-etch-photograph cycle needed to obtain the necessary photomicrographs to portray the spatial microstructure. Statistical methods by their very nature give only average values of the quantities being studied and cannot therefore give a detailed physical picture of the microstructure to be observed. Finally, the technique of selective dissolution is only applicable in systems where the phases are of vastly different chemical reactivity; it is of little use in the study of single-phase alloys. Since the determination of the three-dimensional structure of opaque materials is hindered by two facts—the materials are opaque to radiation in the visible spectrum and construction of spatial models of microstructure is quite laborious—two solutions to the problem suggest themselves: 1) use radiation of energy great enough to render the alloy transparent, i.e., some microradio-graphic method, or, 2) devise a rapid means to section and record alloy microstructure. Stereomicroradiography has indeed been used to study internal arrangements of phases in several materials8,9 but the method, in general, is limited to very thin specimens (due to X-ray absorption) and simple microstructures. It would seem then that development of a rapid, simple, and generally applicable technique for studying the details of alloy microstructures in three dimensions can best be undertaken by following the second approach above. Using this idea a new technique for rapid evaluation of spatial microstructures was developed based upon cinephotomicrographic recording of the micro-structure of a specimen undergoing controlled electrolytic dissolution. It was further felt that application of this technique to the careful study of the spatial configuration of faults in a CuAl2-Al eutectic alloy would yield information that could be correlated with the extensive data3,6,10-12 already compiled concerning the solidification and crystallography of this eutectic. The practicality and usefulness of similar methods for studying three-dimensional features in alloys has recently been illustrated by the study of dislocation loops in zinc13 and spheroidized structure in steel.14

Jan 1, 1965

By Dix, E. H.

THE percentage of manganese used in commercial aluminum alloys is small, and yet this element is an important addition to some very valuable alloys. When used alone with commercial aluminum containing iron and silicon as impurities, the usual percentage in wrought materials is from 1 to 1.5 per cent., whereas castings may contain as much as 2 per cent. An aluminum-manganese alloy containing nominally 1.25 per cent. manganese is much used in sheet form for the manufacture of cooking utensils and other articles requiring a little greater strength and hardness than could be obtained with commercially pure aluminum. It is also used for various purposes in the form of rods, tubes and pipes. The aluminum-manganese alloys, both wrought 'and cast, offer excellent resistance to many kinds of corrosion attack. The U. S. Naval Gun Factory uses an aluminum alloy containing from 1 to 2 per cent. each of copper and manganese, for both castings and forgings. Manganese is also used, up to about 1 per cent., as a minor alloying .element in several of the strong aluminum alloys of the duralumin type. It is felt that the role of this element when thus used has not been fully understood, but it is believed that the results obtained in this investigation will throw additional light on the subject. The earlier work on the system aluminum-manganese was general in nature, and no detailed investigations of the relations existent in the useful aluminum-rich alloys have been reported. Guilletl1in 1902 surveyed the system, and Hendrichs2 in 1908 published an equilibrium diagram which, although based on .few data, is often used in the literature. Fragmentary work has also been done by other investigators."

Jan 1, 1927

By R. W. Raymond

In my former paper (Bans., xii., 410) I quoted the ruling of Judge Hallett, of Colorado, in the "Iron-Smuggler" case, tried before him in June, 1882. Under his charge, the jury in that case found for the defendants, practically declaring that the deposit on the outcrop of which the Iron Silver Mining Company's claim was located was not a " lode," or else that the portion of it within that claim was not the apex. The case was appealed, and the decision of the Supreme Court, given in February, 1886, is reported in 116 U. S. Reports, p. 529. It simply declares that there is nothing in the charge of Judge Hallett to warrant the setting aside the verdict. The definition of a legal lode given in that case, and quoted in my paper at the page above-named, is perhaps the best of several which Judge Hallet has pronounced. That is to say, his earlier definition, that " a lode or vein is a body of mineral, or mineral-bearing rock, within defined boundaries in the general mass of the mountain," is here accompanied with further explanations, which relieve it from the requirement on one hand, that the body shall be continuously ore-bearing if it he only well-defined, and, on the other hand, that the boundaries shall be well-defined if the ore-bearing body be proved to exist. So far as this particular case is concerned, the approval of this ruling by the Supreme Court merely prevents any re-hearing as to the face. Undoubtedly, the evidence was conflicting; and the jury chose to believe, for the purpose of that occasion, the " experts " who

Jan 1, 1887

By J. S. Kirkaldy, W. V. Youdelis

THE occurrence of concentration distributions in rapidly cooled castings with gradients of opposite sign to those expected on the basis of the constitution diagram and diffusion controlled kinetics, has long interested metallurgists. The work on inverse segregation to 1937 has been adequately reviewed by Vaughan, and to 1949 by ell-walpole. The general conclusion for unidirectional solidification, that the enrichment of the initially solidifying regions with lower melting point compositions is due to the flow-back along interdendritic channels of normally segregated residual liquid, has a very sound experimental basis. Perhaps the best experimental work and the most complete qualitative description of the process has been given by Adams.3 The authors accordingly assume the reader's understanding of the content of this paper. It appears that one of the principal deterrents to the complete understanding of the process has been the lack of an analytical description. Although a number of workers including Masing,4-6 Sauerwald,7 and Adams3 have attempted quantitative predictions,

Jan 1, 1959

By Arthur B. Cummins

Diatomite is a siliceous rock of sedimentary origin, which may vary in degree of consolidation, but which consists mainly of the fossilized remains of diatoms. These are microscopic algae of the order Bacillaria. Diatomite is a unique form of silica, there being nothing else found in nature or produced by the manufacturing arts, that has its characteristic physical structure. There are numerous sediments which contain some diatom residues, admixed with a substantial amount of other materials-clay, carbonates or silica. While these are classified as diatomaceous silts, shales, or mudstones, they are not properly diatomite, a designation which is restricted to material of such qualities that it is suitable for commercial uses. The terms diatomaceous earth and kieselgur are synonymous with diatomite. The expressions infusorial earth and tripolite are obsolete. Diatomaceous silica is a definition best used to distinguish the basic component of diatomite, that is, the substance of the silica shell itself and is the major constituent of beneficiated diatomite or processed diatomaceous products. Some highly indurated materials, such as cherty shale, porcelanite, and opaline cherts which have resulted from diagenetic changes cannot be considered as diatomite although they may have been derived therefrom. On the other hand, diatomaceous oozes or loose sediments consisting mainly of diatom residues with or without much organic matter are source materials in process of becoming diatomite. Composition and Properties Pure diatomite is composed of opaline or hydrous silica, with small amounts of associated inorganic components-alumina, iron, alkaline earths, alkali metals, and minor constituents, all of which may occur in solid solution or as an essential part of the opal complex. Crude diatomite on the other hand may contain variable amounts of organic matter and soluble salts, and the usual contaminants of sedimentary formations-particles of rockforming minerals, sand, clay, or carbonates. As occurring in nature, diatomite contains an unusual amount of free water, which may vary from 10 to 60 pct or more. Diatomite, in the dry deposits which are characteristic of most of the important world deposits, occurs as a lightweight, comparatively light colored, "chalklike" material. The apparent density (dry basis) in situ varies from 20 to 40 lb per cu ft. The structure may be either massive or finely stratified. The earth is highly porous, usually soft and easily friable. It is nonreactive with acids and may be tentatively identified by the above characterizations. Confirmation is by microscopic examination which readily reveals the nature of the material. In deposits which contain organic matter the appearance of the material is totally different. The color may vary from light tan or gray to brown, greenish or nearly black. There is frequently difficulty in distinguishing it in the field from peatlike materials, but the difference is readily apparent after calcination. Powdered diatomite or diatomite products have an apparent density (loose weight) of 5 to 16 lb per cu ft, wet densities of 10 to 30 lb per cu ft, specific gravities 1.9 to 2.35, index of refraction 1.42 to 1.48. Diatomite is essentially micro-amorphous, but does show some tendency toward orientation in structure after a cristobalite pattern. Amorphous silica has been considered as a random association of cristobalite crystallites, the size of which are only slightly larger than a unit cell.20 The prop-

Jan 1, 1960

By O. C. Baptist

The Umiat oil field is in Naval Petroleum Reserve No. 4 between the Brooks Range and Arctic Ocean in far-northern Alaska. The Umiat anticline has been tested by 11 wells, six of which produced oil ; however, [lie productive capacity and recoverable reserves of the field are subject to considerable speculation because of unusual reservoir conditions and because several wells appear to have been .seriously damaged during drilling and completion. Oil is produced at depths of 275 to 1,100 ft; the depth to the bottom of the permanently frozen zone varies from about 800 to 1,100 ft, .so that most of the oil reserves are in the permafrost Reservoir pressures are estimated to range from 50 to 350 psi, increasing with depth, and the small amount of gas dissolved in the oil is the major source of energy for production. Laboratory tests were made on cores under simulated permafrost conditions to estimate oil recoverable by solution-gas expansion from low saturation pressures. The cores were also tested for clay content and susceptibility to productivity impaiment by swelling clays and increased water. content if exposed to fresh water. The results indicate that oil can be produced fronz reservoir rocks in the permafrost and that substantial amounts of oil can be produced from depletion-drive reservoirs by a pre.s.r~lrr drop of as little as 100 psi below the saturation pressure. Freezing of formation water reduces oil productivity much more than that due to increased oil viscosity: Failure of we1ls drilled with rtuter-base mud to produce is attributed to freezing of water in the urea immediately surrounding the wellbore. Swelling clays apparently contributed very little to the plugging of the wells. INTRODUCTION Naval Petroleum Reserve No. 4 lies between the Brooks Range and the Arctic Ocean in northern Alaska. The Umiat oil field is located in the southeastern part of the Reserve and is about 180 miles southeast of Point Barrow (the only permanent settlement in the Reserve and the primary supply point for drilling of the wells at Umiat). Eleven wells were drilled for the U. S. Department of the Navy, Office of Naval Petroleum and Oil Shale Reserves, between 1944 and 1953 to test the oil and gas possibilities of the Umiat anticline. Six of these wells produced oil in varying quantities and the best one pumped about 400 B/D.' Estimates of recoverable oil range from 30 to 100 million bbl. The main oil-producing zones are two marine sandstone beds in the Grandstand formation of Cretaceous age: these are referred to as the upper and lower sands. Good oil shows were found throughout the sand settions in the first three wells drilled on the structure, but the highest rate of oil production obtained on any 01 the many tests was about 24 BOPD. These first wells were drilled with conventional rotary methods using water-base mud; later wells were drilled either with cablc tools using brine or rotary tools using oil or oil-base mud. These experiments were successful as is shown by comparing the oil production from Well No. 2 with that from No. 5. These two wells are only 200 ft apart and are located at about the same elevation on the structure. Well No. 2. drilled with a rotary rig using water-base mud, was abandoned as a dry hole after all formation tests were negative. Well No. 5. drilled with cable tools and reamed with a rotary using oil, pumped 400 BOPD which was the maximum capacity of the pump and less than the capacity of the well. These field results indicated that the producing sands were extremely "water sensitive" and it was assumed that the cause of this sensitivity was the presence of swelling clays in the sands. Because of the very unusual reservoir conditions and the difficulties encountered in completing oil wells in the permafrost. the Navy asked the U. S. Bureau of Mines to make laboratory studies under simulated permafrost conditions to assist them in estimating the production potential of the field and the recoverable reserves. These tests were designed to determine the cause of the plugging of wells in the permafrost and to test oil recovery from frozen sand by solution-gas expansion with the oil gas-saturated at very low pressures. EXPERIMENTAL METHODS AND PROCEDURES Samples Analyzed Core samples were analyzed that represent the lower sand in Umiat Well No. 7, the upper sand in No. 3. and both the upper and lower sands in No. 9. These sands should be productive in all of the wells because of their location on the structure. Core samples from

By D. G. F. Hedley, D. F. Coates, K. Barron

INTRODUCTION Preceding papers presented in this symposium have considered the influence of various parameters, such as geologic structure, groundwater, etc., on the stability of rock slopes and have given some analyses and guide lines for slope design. To carry out such analyses it is necessary to put numbers to these parameters; where possible, this is best done on the basis of in- situ observation and measurement. Since none of the design analyses can be considered exact and since conditions vary during excavation, it is also desirable to monitor the behaviour of the slopes as the excavation proceeds. In this manner a feedback of information on the actual excavation conditions can allow a continuous reassessment of the design parameters to be made and can give early warning of incipient failures. The purpose of instrumenting rock slopes is thus to provide information which fits into one of two categories: (a) To give basic data to assist on-site assessment and design of the rock excavation. (b) To provide data for the control and assessment of safety during excavation. The purpose of this paper is to review briefly some of the instruments and measuring techniques available for gathering this data and to indicate where such data may prove useful. This is not a comprehensive review of all available instrumentation but, rather, is a survey of some of the instruments and techniques with which the authors have had some experience and which have proven useful. STRUCTURAL ASSESSMENT Whilst most structural assessment of a site is done on the basis of geologic mapping and core examination, there exists some instrumentation which can, in particular circumstances, assist in this assessment. Seismic instruments can be used to determine the geometry of formations and to give an indication of the relative competency of rocks. These instruments operate using seismic reflection or refraction techniques and, although mainly confined to shallow sub-surface exploration, can be useful in distinguishing between soil/ bedrock contacts and, in some cases, the extent of weathered surface rock.

Jan 1, 1971

By Wm. A. Haven

As soon as the likelihood of American participation in the war was established, and in spite of the fact that we can produce almost as much as all other countries combined, the demand for prompt deliveries of iron and steel products from American factories began to exceed their utmost capacity, and, after fifteen months of practically full operation, has continued to do so. Therefore, it would seem worth while to review some of the aspects of the supply and demand for steel as well as the efforts that are being made to bring them into balance. It is still being debated as to whether the situation should be defined as a real shortage that will persist through the emergency period or as a temporary one than can be relieved by less drastic measures than a Government-sponsored program of expanding existing plants and building new ones.

Jan 1, 1942

By H. G. Doll

The S.P. log is shown to be a measurement of the potential drop along the drill hole, caused by ohmic effect in the mud. The notion of static S.P. is brought forward, and its relation to the S.P. log is discussed. Other factors influencing the shape and amplitude of the log are considered; attention is given to conditions encountered in practice. Numerous figures are given illustrating graphically the results; these figures are of particular interest for comparison with field examples. The S.P. log, although indicating permeability, is not an absolute measurement of permeability, nor of porosity, of the formations traversed by a drill hole. It is affected by several parameters, such as resistivity of formations and mud, thickness of formations, and others, which should be appraised carefully. Simple rules have been established for a better distinction of the boundaries of permeabl: sections, particularly in difficult cases, such as those encountered in highly resistive formations. A systematic application of the established principles will assist in obtaining more information from the S.P. log than was possible thus far; for instance, under favorable conditions, presence of oil may be detected, or amount of shale in sands may be estimated. Introduction The S.P. log, or spontaneous potential log, has been known and widely used during the last 15 years for the location of permeable beds traversed by drill holes.1,2 In electrical logging practice, the S.P. log is shown on the left hand side track of the record (as may be seen in later examples) where it can be easily correlated and interpreted with the resistivity curves located to the right. Usually, the S.P. log consists of a base line, more or less straight, having excursions or "peaks" to the left. The base line frequently has been found to correspond to impervious beds, while the peaks are usually found opposite permeable strata. Measurements which will indicate positively the presence of permeability in the formations, and which will give accurately the boundaries of the permeable zones, are of great importance in oil-field practice. Thus far, the S.P. log is the best approach to such determinations; unfortunately, its interpretation is not always evident. With respect to the base line of the S.P. log, it may be noticed that this line is not always at a definite location on the chart. Sometimes it may shift abruptly, while other times a gradual drift is apparent. As far as the peaks are concerned, their shape is not uniform; some are rounded while others are sharp. Also, from other data, it may be found that occasionally the peaks extend appreciably beyond the boundaries of permeable zones into zones which are not everywhere permeable. A comparison with permeability measurements made on cores has often confirmed that there was no definite correspondence between the magnitudes of the peaks and the permeability values. In the same geological horizon, it generally will be found that most of the thick and permeable for-

Jan 1, 1949

By C. H. Mathewson, E. M. Thalheimer

In planning the present experiments, we have made a particular effort to secure that adjustment of working conditions which would render the forthcoming tests most serviceable by way of indicating the comparative properties of the three different commercial grades of copper used. More specifically, we have endeavored to obtain certain definite information with respect to the relative behavior under test of ordinary electrolytic copper and furnace-refined lake copper containing (a) a moderate percentage of arsenic and (b) a rather large percentage of arsenic, in addition to the usual content of silver and other impurities. These comparisons were made systematic and comprehensive by testing throughout a series of (eight) reductions running from 0 to 70 per cent. in the case of cold-rolled metal, and throughout a series of (15) temperatures running from 100' C. to 1,000" C. in the case of annealed metal. In other words, a survey of properties similar to that made by Grard,' in the case of electrolytic copper, was here repeated (with modifications) and extended to two other commercial varieties of copper. The great importance of copper both as a material of construction and as the base of our most important alloys (aside from steel) has led to innumerable investigations of its properties, particularly in commercial forms. Naturally, the merits of furnace-refined lake coppers us. those of the very pure electrolytic product have furnished the subject of much experimental work and animated discussion, wherein the effect of arsenic has by no means been overlooked. In the literature of the past 10 years,

Jan 1, 1917