Search Documents

By Stanley Reichert

The manganese deposits of the Embree Iron Co., Embreeville, Tenn., are thought to be fairly typical and representative of the East Tennessee type of deposit, and so to warrent rather detailed description. The methods used by the Embree Iron Co. for prospecting and mining, and to a lesser extent for milling; should therefore be applicable to other East Tennessee manganese deposits, as yet' undeveloped. Early History and Discovery of Manganese Brown iron ore (limonite) was mined by the Embree Iron Co. at various times from 1890 to 1910. The early method was simply pick-and-shovel mining in open pits. Later hydraulic giants were used and sluice lines carried the ore down the mountain slopes to log washers.. During this phase of mining, manganese ore was discovered under the iron ore in some of the pits. In other areas oxidized zinc ore was found under the iron. It thus happened that the valuable zinc deposits were discovered in 1914. During the World War period, from 1914 to 1918, there was sporadic prospecting for manganese ore among the abandoned iron workings, but the main activity then centered around the recently discovered lead and zinc deposits. It was not until 1934 that manganese mining began in earnest, under the supervision of R. D. Pritchett, Mine Superintendent. Geology of the Manganese Deposits United States Geological Survey Folios 151 (Roan Mountain) and 118 (Greeneville show that Bumpass Cove is a synclinal structure thrust faulted along the southeast flank, but with normal sequence of strata along the northwest flank. Fig, l. shows the areal geology of Bumpass Cove as taken from the folios superposed on the U.S.G.S. -T.V.A. 1/24,000 topographic maps of the Erwin and Telford 7 ½ minute sheets. The manganese mines occur near the contact of the unfaulted Shady dolomite and the Erwin quartzite. This contact zone is deeply weathered, with overburden averaging 40 to 60 ft. thick. The material overlying' the bedrock along this normal contact is a very tough, plastic clay, termed "buckfat" or "ocher" by the miners. It is not a true ocher, however, in the sense of having commercial value. The manganese deposits occur along this "ocher" band. Fig. 1 also shows how the manganese deposits occur along the broad topographic terrace between the 2100 and 2200-ft. contour lines. This terrace lies at the foot the Erwin quartz ridge. Apparently it is the topographic is expression of the deeply weathered zone along the Shady-Erwin contact.

Jan 1, 1941

By Persifor Frazer

IN his “Final Report," Vol. II, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

Jan 1, 1877

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By Persifor Frazer

In his " Final Report," Vol. 11, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

By Paul Tyler

STRATEGICALLY situated in almost the heart of the leading fertilizer-consuming area of the United States, Tennessee long has ranked second only to Florida as a phosphate-producing state. Since 1932 its share of the national output of phosphate rock has increased steadily, and in 1937 its production mounted to an all-time record. More significant even than the increase in tonnage are the forward strides in technology. The Tennessee Valley Authority's research program has led to quasicommer-cial operations using hydroelectric power to manufacture concentrated phosphatic fertilizer that is used to further the farmer education program designed to streamline the fertilizer business and halt the appalling waste of farm land by soil erosion. Even more stimulating to chemically minded imaginations is the production of elemental phosphorus by a private company that not only has succeeded in extracting it from the phosphate rock in electric furnaces but actually has contrived to capture it and to transport it safely in tank cars. New values have been created for low-grade phosphate deposits, and the economic life of reserves has been lengthened while the waste of former years goes back into the mills for recovery of its values by modernized methods. Tennesse's phosphate-mining industry dates from the discovery of blue rock in Lewis County in December 1893. Its known reserves are of the order of 101,500,000 tons, which compares with the production of 825,099 tons in 1937; that is, 21 per cent of the phosphate-rock output of the whole nation. The total output reported from 1894 until July 1, 1938, was approximately 19,000,000 tons. Official estimates of reserves are overly conservative and evidence submitted before a joint Con-gressional committee in November 1938 places "probable" reserves at more than 6,000,000,000 tons.

Jan 1, 1939

By Benjamin F. Merembeck

A mutispectral scanner (MSS) obtains remotely sensed data of the earth's surface in vector form, one vector element for each spectral sensing band of the MSS. Data generated by either airborne or orbiting MSS systems are organized in a lattice of scan lines and elements within scan lines. Each element, called a pixel, is represented by an observational vector and corresponds to a relatively small specific area on the ground. The total observations for a sensed scene frequently are in the millions and are composed of a number of populations, each representing a different land form category. Based on samples from the populations, the mean vectors, or spectral signatures, and the covariance matrices for the categories may be estimated. From these, an among category covariance matrix and a combined within category covariance matrix can be found. The total among category variance is the trace of the among category covariance matrix. Canonical analysis finds a linear transformation matrix such that the first transform variable accounts for the maximum possible part of the total among category variance. Similarly, the second transform variable, orthogonal to the first, accounts for the maximum possible part of the remainder of the total variance, and so on. Such transformation often results in over 95 percent of the total variance accounted for in the first three canonical variables, even though the initial number of spectral bands exceeded twenty. Transformation of bulk data into three canonical variates allows color map products to be developed by assigning each variable to a different basic color. Such color products are believed to be more useful for photo-interpretation than color products resulting from any combinations of three of the initial spectral bands.

Jan 1, 1977

By J. C. Trantham, J. W. Marx

From 1955 to 1958 the Phillips Petroleum Co. conducted a series of small scale counterflow combustion field tests in a tar sand about 60-ft deep and 6 to 12-ft thick near Bellamy, Mo. A total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern, were employed. Electric heaters, gas burners and wellbore fuel packs were tested as counterflow ignition devices. Direct drive ignition followed by reversal to counterflow operation was not possible in this case because of formation plugging by the semi-solid tar during the direct drive phase. Sustained counterflow burning was achieved with wellbore fuel packs under conirolled conditions which permitted close correlation of fire front velocity, air velocity, air-oil ratios and yields for a wide variation in process parameters. The tar in place was about 10' APl with a reservoir viscosity greater than 500,000 cp. The composite oil prodlcct was 26' API with a viscosity in the range of 5 to 15 cp. Vertical sweep efficiency in the line drive pattern was essentially 100 per cent, with no evidence of gravity segregation. Original tar in place ranged between 800 and 1,000 bbllacre-ft, specific rock permeability averaged about 800 md before burning and effective air pemeability with residual oil and water in place (at the time of ignition) averaged 250 md. The volume of oil recovered during stabilized line drive counterflow burning represented about 67 per cent of the volume of tar originally in place in the burned out zones. A minimum was found when air-oil ratios were plotted against formation air velocities, and a limiting air velocity existed below which the counterflow fire front reversed and burned back over its own trajectory, using the residual coke left behind. INTRODUCTION Early in 1955 the Phillips Petroleum Co. began preparations to field test counterflow underground combustion as a method for producing oil from high viscosity hydrocarbon deposits, such as bituminous (tar) sands. At that time all published information on the use of underground burning io increase oil recovery was based on the direct drive process, in which the fire front moved through the formatim in the same direction as the injected air stream. Such direct burning is not applicable to many heavy oil sands or to most tar sands because the heat-thinned native hydrocarbon congeals in the cold rock ahead of the fire front forming a gas permeability block which smothers the combustion. Laboratory experiments first demonstrated that this permeability blocking would not occur if the fire front and the air stream moved in opposite directions. In this counterflow (reverse) burning process the heated heavy oil or tar is driven back through the combustion zone. Here thermal cracking produces relatively light hydrocarbon products which pass through the heated rock behind the fire front (largely in the vapor phase) and are incapable of causing a gas permeability block.' Exploratory wring revealed that consolidated bituminous sandstones with a combination of tar saturation, permeability, thickness and depth favorable for experimental field testing existed at several points in western Missouri. By the fall of 1955, a test site for determining technical feasibility of the counterflow process under field conditions had been selected near Bellamy, Vernon County, Mo. — about fifty miles north of Joplin. The pay zone was too thin and too shallow to constitute a commercial prospect, but these same factors permitted controlled experimental operation with a small compressor installation and with a large number of monitor wells. These were needed for adequate observation of the underground phenomena at reasonable cost. RESERVOIR CHARACTERISTICS The reservoir chosen for the experimental field tests was a 124 thick section of tar sand extending from 49 to 61 ft subsurface, with shale and siltstone laminations sealing the top and bottom. This section was part of a larger 30-ft thick tar sand deposit which extended both above and below the test zone. Core analyses showed that the 12-ft sand was effectively subdivided into two approximately equal sections, with the lower zone being consistently more permeable than the upper zone. The most significant laboratory core data are summarized in Table 1. The line drive test which is the principal subject of this report utilized only the lower 6-ft thick zone, with the upper zone regarded as part of the 55-ft overburden. WELL PATTERNS The over-all field test program involved a total of seven different well patterns, including conventional five-spots and seven-spots plus a 15-well line drive pattern and a 10-well radial pattern. In some of the tests the full 12-ft zone was employed; in other cases only the more perme-

Jan 1, 1967

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after being pulverized to pigmentary size. The current world production of iron oxide pigments is estimated by the author to be between 499 and 590 kt (550,000 and 650,000 st) based on 1979 data. The fact that highly colored natural deposits of iron ore are found throughout the world accounts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments produced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970) and increasing to $97 million by 1980 (Spinrad, 1980). Nomenclature With the increasing importance of the synthetic iron oxides it is necessary to make a distinction between the natural or mineral pigments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a commercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pigments. Natural pigment ore sources are selected for their special physical-chemical properties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pigmentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments. Classification An important characteristic of a pigment is its color and, therefore, a logical separation can be made on this basis. A. Yellow Iron Oxide Pigments 1. Natural mineral origin a) Goethite b) Lepidocrocite c) Ochres d) Siennas e) Limonite 2. Synthetic pigments a) Goethite B. Red Iron Oxide Pigments 1. Natural mineral origin a) Hematite b) Siderite (calcined) c) Pyrites (calcined) 2. Synthetic pigments a) Hematite C. Brown Iron Oxide Pigments 1. Natural mineral origin a) Umbers b) Limonite (calcined) c) Siderite (calcined) d) Goethite (bog ore or sulfur mud) 2. Synthetic pigments a) Blends of hematite, goethite, and magnetite

Jan 1, 1983

By N. H. Emmons

An interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at its plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory. Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaccs. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top mas necessary and the engineering force was started on the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of east copper, but the heat was great that the copper bent readily, due to the jarring of its

Jan 1, 1911

By A. W. Hesse

The trend of American construction toward permanence and longevity is noticeable in the more recent coal plant installations; also, the policy of many coal operators has changed from seeking to obtain the desired tonnage from several plants of small capacities to designing a single installation to produce the whole amount. The mine openings and plant of the Nemacolin mine of The Buckeye Coal Co., are located on the Greene County side of the Monongahela River, 73 miles south of Pittsburgh. The map (Fig. 1) shows the general location, also the Lambert syncline. This syncline partly accounts for the selection of the site; the other reasons were the possibilities of rail and river shipments. Two shafts and a slope were sunk to the coal, work starting on all three in the second half of the year 1917. The air shaft was sunk to a depth of 243 ft. and completed in February, 1918; the slope was completed in November, and the skip shaft was stopped at a depth of 21 ft. below the coal, then the concrete lining was stopped 8 ft. above the coal August, 1918. Work on the skip shaft was resumed May, 1923, and sunk to a depth of 60 ft. below the coal by September, but it was not until May, 1924, that the lining was poured. Max. Min. WateR Water during after Sinking, Crouting, Depth or Cu. Yd. Cu. YD. Gal. per GaL. per Opening Size Length Excav. Conc. Min. Min. Air shaft..... 20 ft. diam. 251 ft. 8 in. 4788 1902 475 2 Slope........ 11 it. by 19 it. 1 in. 857 ft. 11500 5200 50 2 Skip shaft.... 32 ft. 8 in. by 12 it. 8 in. 296 ft. 6042 2293 300 3 Fig. 2 shows sections of these openings. The surface plan shows the relative positions of the openings. Coal was first hoisted from the air shaft May 7, 1918, and entry driving was continued; but the coal had to be stored, as the railroad had not been extended from Crucible to Nemacolin. As soon as the slope was driven to the coal and the linings concreted, the entries were driven along projected lines to connect with those advancing from the air shaft, and skip shaft. As soon as the underground connections had been made between the two shafts, the hoisting by buckets was inaugurated at the skip shaft and construction on the fan at the air shaft started.

Jan 1, 1927

By W. G. Frailing, W. P. Sims

The Lakeview Pool of Kern County, California, was discovered in 1910 with the drilling of Lakeview No. 1 which blew out and produced an estimated 8,250,000 bbl of oil in 544 days of uncontrolled flow. The well has since been known as the Lakeview Gusher. Full exploitation of the pool did not take place until about 25 years later. A total of 112 producing wells were completed in the Lakeview sand through April 30, 1949. As of that date, about 30 per cent of the total wells drilled were still producing, with an average pool production rate of approximately 2000 bbl per day. The cumulative oil production was about 41 million bbl of oil, or 55.3 per cent of the tank oil originally in place. The pool is bordered on its down-structure side by a body of inactive edgewater and water production where present has been principally the result of coning. Since the depletion of the greater portion of the gas energy by the Lake-view Gusher, the pool has operated under gravity drive. Relatively high angle dips, good permeabilities and favorable fluid characteristics have made gravity drainage particularly effective. Since January, 1942, the oil recovery -has been relatively constant at about 53,000 bbl per ft drop in fluid level. Correlations between the volume of reservoir space drained and the cumulative oil produced indicate that an ultimate recovery of 63.3 per cent of the tank oil originally in place is attainable. INTRODUCTION The Lakeview Pool is an outstanding example of gravity drainage. It is one of many productive reservoirs of the Midway-Sunset Field, and is located in Kern County, approximately five miles southeast of Taft and two miles north of Maricopa, California. Its position rel- ative to surrounding pools and to the Thirty-Five anticline is shown on Fig. 1. The northern portion of the pool lies in sections 32 and 33, Township 32 South, Range 24 East, Mt. Diablo Base and Meridian, while the southern portion lies in sections 25, 26, 35 and 36, Township 12 North, Range 24 West, San Bernardino Base and Meridian. As no two sections bear the same number, they will hereafter be referred to by section number alone. The purpose of this paper is to review the performance of the Lakeview Pool in an effort to evaluate the effectiveness of gravity drive as a recovery mechanism. REGIONAL STRATIGRAPHY AND STRUCTURE The oustanding structural feature is this area is the Thirty-Five anticline, the axis of which plunges South 75" East through the center of Section 35. As shown on Fig. 2, the following zones are oil and gas bearing in the Thirty-Five anticline area: Pleistocene Basal Tulare Tar Sands Pliocene San Joaquin Mya Sands Top Oil or Scalez Zone Etchegoin Kinsey Sand Wilhelm Zone Gusher Sand Calitroleum Sand Miocene Reef Ridge Lakeview Sand Sub-Lakeview Miocene Sands Monarch Sands or fractured shale equivalent Maricopa Webster Sand or fractured shale equivalent Fractured Shale-Uvigerina Zone C Obispo Sand and fractured shale equivalent Pacific Shale Zone The productive interval of the Lakeview Pool is limited to Upper Miocene and Lower Pliocene deposition. In this general area, the most prevalent type of accumulation results from stratigraphic traps or permeability pinchouts. As is the case of the Lakeview Pool, strati-graphic traps resulting from angular unconformities are present. The structure within the Miocene does not parallel that of the Etchegoin (Pliocene), as the Miocene beds were folded, and in places faulted, and subjected to erosion prior to Pliocene deposition. The Lakeview horizon consists of truncated sands which occur on the northeast flank of the Thirty-Five anticline. The direction of strike is west and northwesterly through sections 25 and 36 and continues northwesterly through sections 26 and 33, to the approximate center of section 32. At this point the strike swings to the northeast and the horizon re-enters section 33. in the northwest corner. The change in strike in section 32 affords synclinal accumulation at that point. The Lake-view sand is truncated updip by the Etchegoin overlap. To the southeast, the sand shales out, while to the northwest, the productive interval appears to be limited by a combination of stratigraphic pinchout and permeability barrier. Structurally, the Lakeview reservoir presents three areas of interest, as shown on Fig. 3. Area I in section 32 is a region in which a productive Sub-Lakeview Miocene sand is present. It occurs from 10 feet to 30 feet below the base of the Lakeview sand and attains a maximum thickness of 25 feet in Well No. 21, section 32. The producing characteristics of the Sub-Lakeview Miocene sand differ radically from those of the Lakeview sand. Water production at high structural locations and abnormally high fluid levels indicate that there was no communication with the Lakeview sand. Wells in Area I penetrated this sand and produced it in conjunction with the Lakeview sand. In Area 11, the Lakeview sand is a

Jan 1, 1950

By W. C. Ellis, M. E. Fine

INTRODUCTION IN the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;1 the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition which has a large effect on other properties. The thermal expansion data for the system have been reported3,4.5,6 only from room temperature to 100°C, and for this temperature range a minimum in coefficient in the region of 50 at. pct cobalt is well established. 3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the interrelation. EXPERIMENTAL PROCEDURE The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 50 pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 ½ in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for r hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,7 the differential expansion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outer silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested on a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A non-oxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1948

By Albert E. Wiggin

PagE I. Early History of Boston & Montana Mill at Great Falls (1891 to 1905). 210 a. Original Mill Built in 1891.........210 b. Coarser Concentration Tried...211 c. Screen Sizing of Fine Jig Feed Introduced..211 d. Installation of Finer Grinding.......211 e. Steam Stamp Tried in Place of Blake Crushers..... 211 j. Mill Increased from Three to Six Sections........ 213 g. Tonnage Increased from 300 to 450 Tons per Section... 212 h. Round Tables Replaced by Wilfley Tables....212 I1. Hancock Jig Replaces Evans Jig...212 a. Description of Hancock Jig...213 - b. Tests Made on- Hancock Jig..213 1. Treating Natural Feed..215 2. Treating Sized Feed..215 3. Treating Classified Feed .215 c. Tests Made on Evans Jig...216 III. Richards Pulsator Classifier System...218 a. Experimental Work.....218 b. Installation of System in Section No. 4,....... 220 IV. Woodbury Classifier and Jig System.............222 V. The Great Falls System................ 222 a. As Installed at Anaconda............ 224 1. Coarse Crushing and Jigging Division...... 225 2. Hancock Jig Division........... 226 3. Fine Middling Division.......... 229 4. Table Division............. 230 5. Slime Division.........230 b. Special Features of Great ails Flow sheet....... 231 1. Development of Hancock Jig Flow Sheet..... 231 2. Development of Finishing Table Flow Sheet.... 232 3. Treatment of Coarse Middling Table Products .. 232 4. Results of Test Made on 500-Ton Section at Great Falls Mill...........234 VI. Comparison of Great Falls and Evans System at Anaconda.... 236

Jan 1, 1914

By D. Kuhlmann-Wilsdorf

A new theory of work hardening is developed which rests on only a few simple principles and is applicable to a wide variety of materials and dislocation structures. It explains, qualitatively, the general characteristics of the three-stage shear stress-shear strain curve of fcc metals, as well as the most important features connected with easy glide. The value of, the work-hardening coefficient in stage 11, is derived quantitatively, from first principles, and is shown to be insensitive to many changes in detailed dislocation behavior. The low rate at which energy is stored during mechanical working in stage 11, the dependence of slip line length on stress, and the so-called Cottrell-Stokes law are explained. Although the theory is primarily developed for fcc metals and alloys, it is largely applicable also to some other materiuls, and in particular apparently to poly crystalline simple steels in theh linear range of hardening. FOR pure fcc metals and alloys, after many different pretreatments and under a great variety of testing conditions, the well-known three-stage work-hardening curve is commonly observed. Moreover, the work-hardening coefficient in stage 11, 011, bears an almost constant relationship to G, the modulus of rigidity, such that K = G/Brr" = 300, within a factor of about 2 either way. The very fact that the three-stage curve and the value of K are so very persistent, can hardly be understood except on the assumption that some quite simple phenomena are responsible. In this light all available theories of work hardening must be judged unsatisfactory: Each of them is based on some quite specific dislocation model, while it is known that metals with similar values of K may have widely different dislocation structures, for example, dislocation tangles in the case of pure fcc metals, and piled-up groups of dislocations in a-brasstype alloys. Thus, while a particular theory might conceivably represent a special case with a reasonable degree of accuracy, it cannot possibly have illuminated the underlying principle. Another severe criticism applying to the presently most widely discussed theories is that they employ empirical or even quite unexplained parameters in order to arrive at a numerical value of K. This indicates that some vital aspect of the work-hardening process has remained unexplained. In the present paper, a new theory of work-hardening is developed which does not suffer from the above shortcomings. It is derived from first principles, and is founded on the realization that the underlying causes for the three-stage work-harden- ing curve and for the persistence of the numerical value of O,, must be few and simple. As a first step it is shown herein that the experimental oklservations on "easy glide" can be explained on the assumption that in this stage dislocations multiply, beginning in a number of restricted area:;, and from there penetrate into crystal regions still substantially free of glide dislocations until a quasi-uniform dislocation distribution has been established. During "easy glide", the resistance to the movement of the foremost dislocations, advancing into still largely a dislocation-free regions, is believed to control the flow stress. This resistance is determined by various factors, among them the reaction of the dislocations against bowing-out into loops, which is due to their line tension. Without such bowing-out no dislocation multiplication would occur, but the corresponding contribution to the flow stress stays practically constant all through stage I. According to the present theory, stage TI begins as soon as there are no more areas left into which newly formed dislocations have not yet penetrated, i.e., as soon :is a quasi-uniform dislocation density has been attaned. Regardless of how, in detail, the dislocations should happen to be arranged at the end of "easy glide", whether in pileups or tangles, on one glide system or on several, the stress necessary to overcome the line tension of the segments must now increase, because the dislocation density increiises while the average free dislocation length decreases. It is argued that all other contributions to the flow stress stay at about the same level as in stage I, and that the said increase in the stress necessary to bow out dislocation segments into loops is responsible for the major part of work hardening in stage 11. Stage TII of the stress-strain curve is explained by largely follouing the ideas of Seeger and his co-workers; however, it is pointed out that the start of stage m may on occasion indicate the onset of "conservative climb" instead of cross slip. Indirect evidence indicates that linear work hardening persists even under the profuse action of cross slip, but at a lower rate. Only when, in addition to cross slip, climb operates extensively, does the work-hardening rat,. drop sharply, ultimately down to zero. BRIEF SURVEY OF EXPERIMENTAL EVIDENCE The stress-strain curve of crystals of many different substances are qualitatively similar. No significant permanent plastic deformation takes place below the so-called "critical resolved shear stress". As the applied stress is raised beyond this level. yielding occurs with little or no work hardening and

Jan 1, 1962

By C. H. P. Lupis, Henri Gaye

There are m -I conditions for the stability of a solution of m components with respect to infinitesinzal flucturations. However, in most cases, only one of these conditions has to be considered to determine the domain of instability and the existence of this more restrictive condition greatly simplifies the calculations. It may be used advantageously for the prediction of miscibility gaps and the method is illustrated in details for the case of the Ag-Pb-Zn system. THE thermodynamic conditions for the formation of a miscibility gap may be viewed as a necessary consequence of the conditions for spinodal decomposition. A previous article1 has examined in detail the form of these conditions for multicomponent systems. There is only one condition for the stability of a binary system (with respect to infinitesimal fluctuations), but there are two conditions for a ternary system, and m — 1 conditions for an m-component system. The probability of violating a stability condition, and thus forming a miscibility gap, obviously increases with the number of components, a result which is rather intuitive since the atoms of the solution have now many more ways of redistributing themselves and introducing complexities in the form of the free energy hy-persurface. It is of interest to take advantage of this possibility of precipitating new phases and to examine which stability condition is the likeliest to be violated, that is, which stability condition is thermodynamically the most restrictive. The finding of such a condition would greatly simplify the application of the stability criteria since only one condition could then be considered, instead of m - 1. In Ref. 1, coherency strain energy terms were neglected, thus restricting the applications of the treatment to solutions where they are negligible, such as liquid alloys. In the following study the same assumption will be made. To generalize the treatment to systems where the strain energy terms are sizable, the reader is referred to Cahn's classical article on spinodal decomposition.2 Let us designate by Gij the second derivative of the Gibbs free energy with respect to the number of moles ni and n j. There are several equivalent sets of m — 1 stability conditions.' The one considered here expresses that the successive diagonal determinants of order 1, 2, ... m — 1, associated with the symmetric Gij matrix (for 2 5 i, j 5 m) are positive.' For a binary solution 1-2, the condition for stability is: O(u=G22^0 [1] For a ternary system 1-2-3, the condition [I.] is re- tained (the value of G22 will differ, of course, according to the concentration of 3) and another condition is introduced: £>(21 = G22G33 - Gl3 ^ 0 [2] In a composition diagram, these two conditions define two domains of instability. Starting at a point where the solution is stable (for instance at a point where the solution is very dilute) we gradually change the composition until the condition [I] or [2] is violated. As already noted in the literature, e.g., in the work of Prigogine and Defay,3 it is the boundary of the domain (2) which is first crossed. For if we assume that the boundary of the domain (1) is reached first, at this point G22 = 0 and the second condition is necessarily violated (D(2) = -& 5 0), in contradiction with our original assumption. An exhaustive study of the ternary regular solution case may be found in the work of Meijering.4 Moreover if the boundaries of the two domains have a common point, they also have a common tangent. For if the two lines were to cross each other as is illustrated in Fig. 1(a) any point M in the line QP would be such that £> = 0 and 0"' > 0 which, as shown above, are incompatible results. Thus, the two lines must be tangent at their common point Q as illustrated in the example of Fig. l(b). The reasoning of Fig. l(a) implies that the point Q is not a "singular" point for either boundary line. This singularity may be of two types. First, the lines meet without crossing each other and without being tangent. Second, the tangent at Q for D"' or 0"' is not single-valued. Other types of singularity are unlikely because of the usual analytical forms of D"' and 0"'. The exception to the common tangent requirement due to the first type of singularity was pointed out by John Morral;5 it occurs when the common point, Q' or (3" in Fig. l(b), is located at a boundary of the composition diagram, e.g., at the line X3 = 0. It may also be noted that at the common nonsingular point Q of D(1) and D(2), Fig. 1(b), G23 is necessarily equal to zero, whereas at a point such as Q' or Q", this conclusion is no longer valid because the product G22G33 is now indefinite (of the form 0. a). The exception to the common tangent requirement due to the second type of singularity occurs when two branches of the same boundary line intersect, for example when D(1)or D(2) decomposes into a product of functions, at a point which belongs to the boundary of the other condition. It is possible to show by a simple analytical calculation that, in this case, if Q is a singular point of D(1), then it is necessarily a singular point of D(2), and that the reciprocal is true except if G33 = 0 at Q. For the present article, however, more elaboration on these singularities appears to be unwarranted. To generalize the previous results to an m -component system, we use the mathematical theorem stating that if the diagonal determinant D(r) = 0, then

Jan 1, 1970

By E. Miller, K. L. Komarek

Equatiorzs have been derived which related maximum solid solubilities in semicondcting compounds having retvograde solidus curves with 1iqllidus data. Liquidus curves in Lke Pb-Te, Pb-Se, ard PB-S systetris have been defermined by thertrzal aralyses. Fvotrz expevimental maximum solibilities ia CdTe, PbTe, uxd PbS vetvograde tetrperatures hale beep1 calculated. TIze resllts support the concept that under certaiz conditiots pronounced itjlections in the liquidis curves arc indzcatiz:e of retropade solidus curves and that the tenlperatltre of the lmaximum solid solubility will be close to the temperature of the point of inflection in the liquidus curve. The maximum solid solihility within a gvoup of homologous cottrpoods SeetlLs to increase with increasing flatness ol the liquidus curvres. The phenomenon of retrograde solubility in metals, i.e., maximum solubility in a solid terminal phase in equilibrium with a liquid phase, has been theoretically predicted by Van aar' in his calculations of hypothetical binary phase diagrams. It was not until 1926, however, that retrograde solubility was experimentally verified in the Zn-Cd system.' Since then many sys- tems with retrograde solubility have been found, so that at present approximately fifty binary diagrams with a retrograde solidus curve are known.3 Meijering4 has critically appraised the accumulated data and has presented calculations which alloy predictions as to whether or not a solidus line will be retrograde. Interest in retrograde solubility increased when it was found that the solidus curves of germanium and silicon alloyed with a great many doping elements are retrrade. The problem was treated thermody-namically by odkinson,% d all available data on solid solutions in germanium and silicon were summarized by Trumbore.7 Although it is to be expected that intermetallic compounds will also exhibit retrograde solubility, experimental evidence is much more limited. Until now retrograde solidus curves have been reported for the compounds de,' be, Ps:" ne," SnSe," and SnS.13 All these compounds are semiconductors, and the solidus curves were usually obtained by determining the carrier concentration at room temperature of samples equilibrated at elevated temperatures and then quenched. It has been hown,'' however, that it is not always possible to quench in the equilibrium compositions from above a certain temperature. Theoretical discussions have either explicitly excluded intermetallic compounds4 or not treated them with respect to retrograde slubilit.j In the following a thermodynamic treatment of retrograde solu-

Jan 1, 1967

By David Sinclair

THE dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests.§ None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their appli-cation in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I THE PHOTOELASTIC METHOD The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution.

Jan 1, 1940

By D. O. Hobson, J. O. Stiegler, C. J. McHargue

The effects of alloy composition, deformation temperature, heal treatment, ad inlerstilial contamination on the occurrence of deformation twins were studied. The twinning transition temperature varied with composition and was a maximuni of 140°C for the 40 pcl V composition. Tire remperature range of the transition was very narrow. Alloys of 20 to 70 pet V could he cold-rolled and exhibited profuse twinning. The alloys which did not twin at room temperature (10, 80, and 90 pel V) could plot be cold-rolled. Oxygen additions systematically lowered the transition temperatures for all vanadium contents. The transition temperature for a 30 pet V alloy increased with annealing temperature, apparently due to changes in dislocation density and configuration. Twinning did not nucleate fracture in any specimen in the 20 to 60 pet V composition range. THERE is great current interest in the refractory metals and alloys as structural materials. An important factor in considering the ductile-brittle behavior of such materials is the role of mechanical twinning as a deformation mechanism. Mechanical twins have been observed after deformation at low temperatures or at high loading rates in the pure metals iron,1 vanadium,2,3 columbium,4,5 tantalum,6 Chromium,7 molybdenum,8 and tungsten.9 Binary alloys in which mechanical twins have been observed include: iron with silicon,10 phosphorous," or aluminum;12 and chromium, molybdenum, or tungsten with rhenium.13-17 The increase in low-temperature ductility obtained by alloying the Group VI-A elements with rhenium is very important with regard to fabricability, and there has been considerable effort to understand the so-called '(rhenium effect". Factors suggested to explain this effect include:'' 1) increase in solubility of interstitial impurities with alloying (electronic effect): 2) changes in the nature of grain boundary phases; 3) changes in interfacial energies of grain boundaries and stacking faults: and 4) promotion of twinning. Although an outstanding characteristic of these alloys is the profuse twinning that accompanies low-temperature deformation, most studies of the rhenium effect have been concerned with the other factors. During recent studies of refractory-metal alloys, it was noted that solid solutions of columbium and vanadium exhibited high hardness and strength at room temperature and elevated temperature and, surprisingly, also showed considerable ductility at room temperature and below. These alloys deformed by twinning at room temperature when subjected to slow loading rates. It appeared that the low-temperature ductility resulted at least in part from the relaxation of stresses by twinning in a system where slip is difficult. The reason for enhanced twinning behavior in some bee solid-solution alloys is unknown. There have been suggestions18,19 that, as in fee alloys, the

Jan 1, 1965

By Charles E. Glass

A steadily growing body of evidence indicates that earthquake ground motions can cause failure of rock slopes that are otherwise stable under static loading conditions. As a result, the economic optimum working slope angle is reduced when earthquake shaking is considered in surface mine design, especially in regions of high seismicity. When designing surface mine slopes to withstand seismic motion it is as important to consider the probability of experiencing various levels of ground shaking as it is to consider the characteristics of the ground motion. For most slope designs, simple probabilistic techniques such as extreme value or maximum likelihood techniques are appropriate. These techniques, however, should be applied in such a way that a probability value is assigned to characteristic ground motion parameters at the mine rather than to nearby earthquake magnitudes. Several techniques have been developed to analyze rock slopes subjected to dynamic loads. Most of these techniques do not adequately account for the ground motion parameters of concern. The best technique appears to be one that utilizes actual earthquake time histories. A simple technique that calculates block displacement for any input accelerogram, using a linear acceleration approximation between time steps, has been developed that accurately accounts for rock block response. Results using this technique indicate that the following factors are important for assessing rock slope stability in earthquake regions:

Jan 1, 1983

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948