Search Documents

By H. I. Aaronson, H. A. Domian

ELectvon-probe analgsis has been used to in7:estigatr the partition ot alloying- elements between aus-tenite and proeutectoid ferrite (or the Jerritic component of bainite) in high-purity Fe-C-X alloys, lsuully at tzco levels of carbon content fca 0.1 and 0.4 pct in ntost steels) at temperatures between the M, and the Ae3 in Si, mn, Ni, mo, Co, Al, Cr, Cu, and PI steels. No partition ous found during the early stages of transformation at any temperature studied in the Si, ,mo. Co, Al, Cr, and Cu steels. Partition did take place, Jrowel'er, in Ihe Mn, ATi, and Pt steels, occurring in lewtperature. regions below the Ae3 of ca 130°, 65", UNDERSTANDING the mechanisms through which alloying elements influence the kinetics of austenite decomposition reactions which proceed by nucleation and 35c respectively. A break was discovered in the TTT curve for the initiation oj the proeutectoid ferrite reaction in the latter steels at the temperature at which partition began. The alloy content in ferrite at the a:y bondavy remained at constart lecels, shown experimentally to be significantly above those corresponding to eqiilib+iu??l, e'en at the longest reaction times investigated (ca 1o6sec). The partition and the TTT curve observations foere rationalized on the basis of the thermodynamic treatment developed in an accompany ing paper. and diffusional growth has been a major research objective of physical metallurgy since the latter part of the 19th century. The measurements made on the dif-fusivities of carbon and of substitutional alloying elements in austenite during the 1930's and 1940's seemed to provide a useful clue as to the nature of these mechanisms. These measurements showed that the diffu-sivity of carbon is several orders of magnitude higher than that of the alloying elements at a given tempera-

Jan 1, 1967

By George A. Packard

WHEN, in April, 1892, the writer began experimenting with the cyanide-process, it had already proved a success in the treatment of tailings, but had not become an important factor as a primary method of ore-treatment. The Livingston, Colorado, mill was running a few small agitators; the Mercur mill, in Utah, was said to be a success, but was " closed down to increase capacity; " and Mr. A. B. Paul, in Shasta county, California, was running ore'through a stamp-mill into leachingvats, using a weak cyanide solution in the battery. Mills had been, or were being, erected in Arizona; on the Comstock lode; and in South Dakota. Some of these never started, and several were shut down or remodelled for other processes. Altogether, the outlook was anything but favorable. Many of these mills were planned to make use of agits tion, and a cyanide solution containing at least 1 per cent. of potassium cyanide was employed. Since then the improvement of the process, both chemically and mechanically, has placed it among the recognized successful methods of oretreatment. Within the past year I have visited a large number of cyanide-mills, and have collected considerable data, of which I publish enough herewith to give an idea of the development of the process and of the methods followed in the principal mills. I would say, however, that nearly all of these plants are experimenting, most of them employing experienced chemists,

Jan 1, 1897

By A. S. Hewitt

After an interval of fourteen years, saddened for all of us by the death of David Thomas, the father of the anthracite iron-trade, first president of the Institute, and by the untimely loss of his successor, Alexander L. Holley, whose memory we are about to honor by loving services, the members of the American Institute of Mining Engineers have conferred upon me for the second time the office of president, under circumstances similar to those which led to the choice in 1876. Then the whole world was represented at the great exposition of industry which was held in Philadelphia to celebrate the one hundredth anniversary of our declaration of political independence. In 1890 it is our privilege to receive as guests the members of the British Iron and Steel Institute, who, with singular and graceful felicity, have appointed a meeting in the United States in the year when we pass from the second to the first place in the international column of the production of iron, and thus celebrate our industrial independence. For the honor of being chosen to extend to our distinguished guests the right hand of fellowship and a hearty welcome I return to my associates the grateful acknowledgment of one whose chief claim to your favor is to be found in his love for the professional occupation in which we are all engaged, and in his efforts, public and private, to promote its advancement into new fields of usefulness. In order to indicate the full significance of the visit of our foreign guests at this time, it will be proper to explain briefly the origin, aims and work of the Iron and Steel Institute. It unquestionably owes its birth to the International Expositions held in London in 1851 and 1862, and in Paris in 1867. These expositions served to break down the jealousies of nationality and to diffuse a better knowledge of industrial processes. Trade-secrets, which had been carefully guarded, became common property; manufacturers who had previously regarded themselves as rivals formed bonds of union and ties of friendship, as the results of an intercourse which

Jan 1, 1891

By T. B. Counselman

AN iron blast furnace of 1000 tons daily capacity will produce about 100,000 cu; ft. per minute of blast-furnace gas. This contains about 25 per cent of carbon monoxide, and has a B.t.u. value of about 95. This gas-is used primarily for heating the stoves of the blast furnace, and secondarily, under boilers, for steam production. Occasionally it is also used in gas engines. The raw gas coming out of the furnace carries about 10 grains of flue dust per cubic foot of gas, under best operating conditions. With the furnace "rolling" or slipping, this quantity may temporarily be greatly increased. This dust would, of course, deposit on the checkers of the stoves, or plug the burners under the boilers; therefore the gas must be cleaned.

Jan 1, 1936

About 1300 members and guests attended the Seventh Annual Mid-winter Convention of the American Institute of Electrical Engineers, which was held in the Engineering Societies' Building, New York, on Feb. 19 to 21. The opening session was a joint session with the American Institute of Mining Engineers, when welding was discussed. The various phases of standardization in engineering work were discussed by President Comfort A. Adams at the Thursday morning session. Thursday afternoon was spent in visiting. Some of the guests visited the Brooklyn Navy Yards, where they inspected the power plant, shops, dry, docks, etc. ; others visited the Bell System Laboratories of the Western Electric Co. The papers at the various technical sessions provoked considerable

Jan 4, 1919

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935

By Heinrich Oscar Hofman

IN THE death of Professor Hofman who was born on Aug. 13, 1852 and died on April 28, 1924, the world has lost a great metallurgist and a great author of metallurgical literature. Measured in time his life was not quite seventy-two years, but measured in work accomplished it was much longer than this. It is not surprising that Dr. Hofman became a great scholar for his father, Karl Hofman, was on the faculty of Heidelberg University, and his early days were spent in these surroundings. He studied in the University under such men as Kirchoff and Bunsen and often spoke of the intimate relations he had with them. Following his course at Heidelberg, he studied at the Clausthal Mining Academy where he graduated with honors, receiving the degrees of Mining Engineer and Metallurgical Engineer in 1877.

Jan 1, 1924

By AIME

A GEOLOGIST --one versed in geology, the science which treats of the history of the earth and its life, especially as recorded in the rocks; that is Webster's definition. William Embry Wrather-one of the country's foremost geologists who heads the U. S. Geological Survey; this is the 1948 President of the Institute. He has studied the geology of areas on the face of the earth as far-flung as Texas and the Balkans, and now heads the world's largest staff of geologists. Vital statistics on Dr. Wrather would show his place of birth as Brandenburg, Ky., the year 1883. He will celebrate his threescore and five years of full living the twentieth of this month. As is usual in biographical sketches of this nature, the formative years of youth, and in many ways the most important years of one's life (since professional tendencies as well as many important personal decisions are evidenced before the teens are left behind) are passed over with the mere fact noted that a degree was earned at such and such educational institution. And so we note that Dr. Wrather received his Ph.B. degree at the University of Chicago in 1907, and followed up that degree with two years of graduate study.

Jan 1, 1948

By E. W. Lithgow, E. G. Williams, R. R. Holbrook, B. R. Wilson

The mineralogy and geochemistry of Pennsylvanian shales and underclays were studied to determine their suitability for lightweight aggregate and refractory ladle brick. Eighty percent of the variation in bloating of shales and clays was explained by the variation of Si02, A1203, and fluxes (Fe203, MgO, CaO, Na20, and K20); 60% by variation in quartz, kaolinite, illite, and chlorite. The best bloating was exhibited by marine shales, whereas freshwater shales and underclays experienced little or no expansion. Regional paleogeographic maps o f Pottsville and Allegheny shales permit bloating to be geographically predicted. It was found that clays meeting the specifications for refractory ladle bricks were obtained from underclays having over 34.5% mica, over 40% kaolinite and less than 15% quartz. Underclays of this composition are confined to the lower Allegheney outcropping along the near-margins of the coal basin. The best clay is that underlying the Lower Kittanning coal. Porosity of the first fired brick was found to be inversely correlated with reheat expansion.

Jan 1, 1975

By Thomas Leonard Watson

SULPHIDE ore-bodies of more or less lenticular shape occurring in metamorphic crystalline schists, gneisses, and. slates, and conforming closely in strike and usually in dip to the inclosing rock, have been recognized and described along the, Atlantic seaboard from Quebec to Alabama. The ore-bodies do not entirely conform, in all cases, to the structure of the inclosing schists, but they sometimes cut across the foliation in dip, though conforming more closely with the direction of strike. In composition the principal sulphide mineral is usually pyrite or pyrrhotite; or both, accompanied by copper, frequently gold, and almost always some sphalerite and galenite. Other. metallic ores are, so far as these sulphide bodies have been investigated, less common; silver is not uncommon, and in some of the pyrrhotite masses nickel is present in quantity sufficient to be commercially valuable. Cobalt frequently accompanies .the nickel, usually in smaller amount, and the two vary much in relative proportion. Quartz and calcite are probably the most common of the, non-metallic minerals. A number of silicate minerals are frequent representatives in one place or another; garnet, amphibole, biotite, pyroxene, zoisite and others. The sulphide bodies of Virginia, comprising both pyrite and pyrrhotite, are among the most extensive along the Atlantic seaboard. Among the pyrite bodies may be mentioned the well-known and extensively worked mines of Louisa and Prince William, counties, located on' the main pyrite belt (A, Fig. 1) of the middle and northern, eastern Piedmont region in Virginia, and among the pyrrhotite bodies is the famous " Great Gossan Lead "(B, Fig. 1) of the Floyd-Carroll-Graysou coun-

Sep 1, 1907

By Allan J. Clark

It is nearly three years since the metallurgy of the Homestake ore was discussed with considerable thoroughness, in a paper1 read before the Institution of .Mining and Metallurgy. Certain changes have been made in this period which are perhaps of sufficient interest to justify a brief description, and it is chiefly with such details and miscellanies that this paper will deal. In the circumstances, a certain amount of repetition is inevitable, but matter treated of in the former paper will be referred to here only when it is necessary for the sake of coherency. For full descriptions of equipment and technique, the former paper should be consulted. The mineralized slates and schists which constitute the ore vary considerably in composition, but the unoxidized ore, perhaps constituting the major part of the reserves, contains either chlorite or hornblende (cummingtonite), with quartz, carbonates of lime, magnesia and iron, and arsenopyrite, pyrite, and pyrrhotite. Ferrous minerals predominate, and this fact has been an important factor in determining the metallurgical treatment. With one or two exceptions the minerals noted are of relatively high specific gravity, and the ore as a whole is exceptionally heavy, many determinations giving an average specific gravity of 3.00. This high specific gravity presents one decided advantage, when the cost of treatment is compared with operations elsewhere, in that the ton, almost universally the basic unit, represents a volume probably less by 10 per cent. than that of many gold ores. On the other hand, this high gravity renders more difficult the discharge of pulp from mortars, its distribution on amalgam tables, and its transportation in launders. In the same way, as attesting the usual balance of such variations of different ores, it may be noted that the needle-like fibers of hornblende (cummingtonite), interlacing throughout the mass, render the ore more difficult to crush than would be anticipated, but on the other hand assist

Jan 1, 1916

J. H. HEGINBOTHAM, a, metallurgist of the General Engineering Co., talked on "Current Milling Practice at Kirkland Lake," at the December meeting of the Utah Section. The ore is enough alike through the whole district so that some generalizations and comparisons may be made. The question as to whether or not the flotation process should be used in the flowsheet for extracting gold by cyanide solutions is still being vigorously debated, and it will seemingly need some years for a definite answer to be given. Most of the gold is either free, though much of it is finely dispersed in quartz, or occurs with pyrite. At times there may be 2 per cent of telluride compounds in the ore, but the amount of gold telluride present is small and has not been definitely established. It has been shown by Dr. Haultain and others that though gold tellurides may be so finely disseminated that it is necessary to grind the ore exceedingly fine, the compounds themselves are not difficultly soluble. (An increase in temperature helps to dissolve tellurides, and also to settle pulps.) It is likely that if the ore were ground through 400 mesh, practically all of the gold would be soluble. As it is, with 96 to 98 per cent of the ore ground to minus 200 mesh, and some 70 per cent minus 325, the cost of

Jan 1, 1934

DAVID WHITE,* Washington, D. C.-This paper is very timely since the Philippine Islands are presumably open to the enterprise of the American driller, whereas much of the territory in that part of the world is closed to us. The United States has ambitious plans for the operation of a great merchant marine, which is to be oil burning in the main, and it takes but a glance at the world map to see the strategic advantage of oil supplies in the Philippines for such marine operations. It is a little difficult to understand why more attention has not been given to the Philippines, in spite of the difficulties attending development in these islands. A number of American oil companies are, I believe, at the present moment taking an interest in the possibilities of the Philippines. Important factors in the formulation of opinion regarding the importance of the oil deposits of the Philippines, as brought out by Mr. Pratt,1 are the point of view and the breadth of experience of the examining geologist. The average oil geologist, whose experience has been mainly in the Appalachian region, the Mid-continent, or Louisiana, or possibly even in California, on seeing the narrowness of the basins, the closeness of the folding, and the presence of igneous rocks here and there, would be likely to draw unfavorable conclusions as to the possibilities of the Philippine Islands. Geologists visiting that region should be familiar with the geological conditions of oil occurrence in Japan, Formosa, the East Indies, or in the Baku district, and their conclusions should be formulated with the knowledge and understanding of the occurrence of oil in those regions rather than in the United States.

Jan 8, 1920

By R. Dawson Hall

LONG regarded as nearly worked out, the anthracite region still shows promise of a hundred years of life, for means are being found to get bottom, top, pillar, and other coal that earlier generations disregarded as too expensive to mine. Rock drivages and, still more, machinery are making it possible to get such coal. Mechanical methods enable the owner of thin beds to mine these with profit, and the miner recognizes that he must permit the use of machinery or the inexorable laws of economics will deny him opportunity to work. E. L. Dana, Jr., well outlines this situation, which in the past year became definitely established. Stripping also is recovering, safely and inexpensively, coal that past generations regarded as too hazardous and costly for mining.

Jan 1, 1935

By Joseph A. Holmes

I. INTRODUCTORY. THE plans for the investigation of fuels and structural materials now being conducted by the Technologic Branch of the United States Geological Survey were, before being decided upon by the Director of the Survey, submitted for consideration to the National Advisory Board, upon which there are nine representatives from the membership of the American Institute of Mining Engineers, viz.: Messrs. John Hays Hammond, Robert W. Hunt, B. F. Bush, and E. V. d'Invilliers (representing the Institute); Messrs. Julian Kennedy and C. S. Robinson (representing the Iron and Steel Institute); Dr. Charles B. Dudley (representing the American Society for Testing Materials); Mr. F. H. Newell (representing the U. S. Reclamation Service); and Dr. Richard Moldenke (representing the American Foundrymen's Association). It seems fitting, therefore, that a report of these investigations of the past three years should be submitted to the Institute for publication in its Transactions. The above, together with other representatives of the national engineering societies and allied organizations, were invited by President Roosevelt to serve, along with the Chiefs of the several Government Bureaus who have charge of public works and large. fuel purchases, on the National Advisory Board to give advice concerning these investigations. The appointment of this National Board grew out of a wish on the part of the President, the Secretary of the Interior, and the Director of the Geological Survey not only that the appropriations for these investigations be expended in a manner most beneficial to the several branches of the government

Jan 7, 1908

By Archer E. Wheeler, Milo W. Krejci

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until June 1, 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston & Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operation of and appliances for the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detaild accounts of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General. Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation. of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres. 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag, General Chronological Review. Ground was broken for the general concentrating and smelting plant in the spring of 1,891. The first departments to start operations were the concentrator in March, 1892, and the Brückner roasting and reverbera-tory smelting departments in April, 1892. The converter department

Jan 1, 1914

By James Kitson, Abram S. Hewitt

I HAVE now the duty—the very pleasant duty—to perform, of presenting to the Hon. Abram S. Hewitt the Bessemer gold medal for distinguished services to the iron and steel trade. When this matter was brought under consideration in London it was well known that, as Mr. Hewitt would be the first to acknowledge, there is more than one man in America upon whom we would gladly have cm ferred this distinction, and to whom this merit might be justly at tributed ; but Mr. Hewitt has been long known to our distinguished members on the other side of the Atlantic as one of the most active minds in the investigation of new methods of manufacture, and one of the most enterprising metallurgists on this side of the Atlantic. Well, gentlemen, we proposed to Mr. Hewitt that he should receive this gold medal, but I think it is quite right, and is his due, that I should state that he at once declined to receive it; and he declined in a manner which rendered it impossible to any one but very per sistent friends and very obstinate Englishmen to refuse. When we heard that our American friends had conferred once more upon Mr. Hewitt the distinction of President of the American Institute of Mining Engineers, and particularly with reference to our contem plated visit, and when we heard that he had been elected unani mously to that position, we felt that we had received the stamp of approval from this side. Gentlemen, as I said before, Mr. Hewitt has long been known to many of us in England as an advocate of scientific education. A report which he made of the metallurgical products at the Paris Exposition in 1867 was one of the matters which drew very clearly and distinctly the attention of the English iron and steel trade to the necessity of further improvement in our technical education as to iron and steel; and it was one of those beginnings which led ultimately to the foundation of the Iron and Steel Institute. The development of the ideas which 'he there investigated undoubtedly led

Jan 1, 1891

By A. G. Metcalfe, A. Siede

The hardening of annealed copper during fatigue testing appears to be independent of the applied stress and to occur largely within the first 4000 cycles. Copper hardened by fatigue is more resistant to annealing than copper hardened by static means, and softens by a multistage process. Creep studies at 300°C show that copper hardened by fatigue also has greater resistance to creep than statically hardened copper. Some theoretical explanations are discussed. RECENT interest in the behavior of metals subjected to fatigue stems from observations of phenomena which could not be explained by current theories of the structure of metals. In 1953 Bullen et al.l showed that the hardening caused by fatigue at low stresses did not cause severe bending of the lattice as did hardening by static methods. This was later confirmed by Wood, 'and Broom and Ham.3 Clarebrough et al4 showed that as the stress level used in fatigue hardening was increased, bending of the lattice was introduced, eventually approaching that of metals deformed by conventional cold-working methods. The type of hardening introduced by fatigue has other interesting characteristics. Kemsley5 showed that copper fractured by fatigue at low stresses resisted annealing as compared to copper hardened an equal amount by static means. The work of Clarebrough etal, shows that the manner of energy release during annealing differs for fatigue-hardened and statically hardened metal in both magnitude and temperature range of release. In addition to hardening of the lattice, fatigue has been shown to cause softening in materials previously hardened by static methods,5 and also in age-hardened alloys.7 The superposition of a small fatigue stress on the static loading of high-temperature alloys has been shown to increase their resistance to creep.' The present work was an attempt to determine the relationship between fatigue hardening, resistance to annealing, and the creep properties of pure copper. EXPERIMENTAL PROGRAM The program described here was designed to answer three questions: 1) Can stress-cycle combinations well below the failure values give significant increases in hardness? 2) Does hardening, under different stress-cycle combinations, give increase resistance to annealing? And if so— 3) Does superior resistance to annealing confer superior creep properties over statically hardened material? Three-quarter hard OFHC copper was annealed in vacuo at 550°C for 1 hr to produce a strain-free material having a fine grain size and uniform hardness. (The standard deviation of the mean hardness of the annealed samples was less than + 1.9 Dpn). Annealing was performed after machining the fatigue specimens so as to avoid work-hardened surfaces. Jigs were used to avoid distortion. The fatigue properties of the annealed copper were determined using an accurately aligned Baldwin-Sonntag SF1-U machine operating at 1800 cycles per min. This limited the minimum number of cycles which could be examined to about 4000 stress reversals. Since failure resulted in specimen damage, hardness increase with number of cycles was measured by testing specimens fatigued to different fractions of the failure values. The results are shown in Fig. 1, and are superimposed on the S-N curve of the copper in Fig. 2. The resistance to annealing of fatigue-hardened material was compared to that of material hardened by uniaxial tensile straining. Specimens hardened to equal values by both methods were progressively annealed for 1 hr at temperature in vacuo. After each annealing treatment the hardness was measured using a Leitz Durimet hardness tester with a 500-g load. At least five tests were made for each hardness determination. The standard deviation for individual specimens varied from 0.26 to 1.48 hardness points. The results are shown in Figs. 3 to 5. The discontinuous nature of the annealing process has been brought out by drawing idealized curves through the data points. This can be justified by the consistency of the results as well as by general agreement with results of Kemsley.5 The creep resistance of fatigue-hardened and

Jan 1, 1960

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down-cast shafts; however, the variation between winter and summer causes a difference of only 2° to 3° in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of tile mine are as follows: LEVEL DEGREES LEVEL DEGREES 2000 109 3200 127 2250 112.5 3400 130 2550 116 3600 134 2800 120 3800 137 3000 124 4000 140 There appears to be no difference in rock temperature for any particu-lar horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock tem-peratures given above is 1 1/2 ° per 100 feet.

Jan 1, 1938