Search Documents

By Louis V. Bender

AfteR investigating the work of coal-dust fired reverberatories of the Canadian Copper Co., at Copper Cliff, Ontario, the management of the Washoe Reduction Works decided to experiment with and ascertain the advantages of using coal dust as a fuel in their reverberatories. Consequently, during the month of June, 1914, reverberatory furnace No. 8 was changed in order to use powdered coal as a fuel. The results obtained by this method of firing are gratifying and show a decided saving in cost of smelting as compared to grate firing with lump coal. The furnace, as remodeled, is 124 ft. long by 21 ft. wide, and varies in height from 8 ft. 6 in. at the back end to 5 ft. 7 in. at the skimming end. The general construction of the furnace is similar to that of the other furnaces at this plant. There are no side doors to this furnace, as it was thought that with the present arrangement for feeding no "fettling" or "claying" would be required. The interior of the furnace can be inspected through the burner port holes, after shutting off the burners and giving a few seconds' time for the gases inside the furnace to clear away. The charging is done on either side of the furnace from longitudinal hoppers, extending a distance of 74 ft. from the back end of the furnace. Leading from the hoppers into the furnace are 6-in. pipes, spaced 191/4 in. apart, through which the charge is intermittently dropped. The charge is kept well above the slag line at all times; in this way the side walls are protected and no fettling is needed on this portion of the furnace. The remainder of the furnace requires fettling. After operating for three months, we found that the bricks were eaten into along each side wall from the skimming door back to the point where the charge had been dropped. The depth of this cutting away was 8 in. close to the front end and gradually tapered to zero at a distance of 50 ft., and was greatest on the side of the furnace having the larger flue connection. Hoppers will be put in for the entire length of furnace, from which fettling material will be dropped, to prevent this cutting. After the run of three months, the roof was in excellent condition. At the back of the furnace the bricks were not cut into at all; at 30 ft.

Jan 1, 1915

The following additional notes about prices of coal in the early days were collected from the sources shown. Several data about canal tolls and labor conditions are also included. 1796, November: "The inhabitants lay it (coal) in at about 3;d. (83¢) sterling per bushel." (Ref. 73: p. 147.) 1804, March: "In March, 1804, I sent a person accustomed to mining to open the vein of coal, and to load the ark, which was accomplished, and early in the month of April the ark, with the first cargo of bituminous coal passed safely the Conewago falls, and landed her coal at Columbia, Lancaster County. The coal was sold at 31¢ per bushel at Columbia." ($7.75 per ton). This was the first coal from Clearfield County near the town of that name. (Letter from William Boyd: Pa. Senate Jour., 1833-1834, vol. 2, p. 561.) 1807: The following notice appeared in the Bedford Gazette: "Huntingdon, June 4. "Stone Coal.-Such of the farmers as wish to make experiment with stone coal as a substitute for plaster, in manuring their Indian corn, may be supplied with coal gratis upon application to Peter Hughes, at Mr. Riddle's mines, on the Raystown Branch. The proprietor of the mines offers not only to refund the carriage, but to pay the expenses of applying the coal, if upon a fair experiment it is found to be inferior to plaster, which now sells at two dollars per bushel." (Ref. 735: p. 708.) 1809: Coal was delivered in Pittsburgh at 5¢ per bushel or $1.25 per net ton. (Ref. 444: p. 50.) Coal was delivered in Connellsville at 4¢ per bushel or $1.00 per net ton. (Ibid.: p. 185.) 1810: Pittsburgh.-"Coal may be obtained of a good quality, ready delivered at 5¢ a bushel." ($1.25 per net ton.) (Ref. 315: vol. 2.) 1811: "It (coal) costs 6¢ a bushel at your door." ($1.50 per net ton.) (In Pittsburgh.) (Ref. 277: 1811, p. 68.) 1814: At Columbia, now part of Donors, Washington County, Pa., an original sale of lots in 1814 gave the purchaser of each lot the right to mine stone coal gratis from a bank on the property. (Ref. 410: vol. 1, p. 547.) "A laborer is able to dig upwards of 100 bushels per day." (4 tons.) (Ref. 277: 1814, p. 109.) A paper about the early newspapers in West Virginia says: "Collier Wanting. From 10 to 20 steady and industrious men, who understand digging coal, may obtain high wages in Kenhawa for that business, if immediate application is

Jan 1, 1942

By N. Albon, J. F. Miller, R. W. Coutant

The deposition of nickel from nickel carbonyl onto amorphous substrates has been studied, with attention being paid to the specific effects of the physical and chemical nature of the substrate and to the effect of oxygen on the crystal morphology. With substrates having microscratches or etch lines, nu-cleation was observed to occur preferentially at these surface features. Flame polishing of the substrate surfaces was found to remove any regularity in preferred nucleation sites. Nucleation was observed to occur less readily on substrates having relatively low surface energies, e.g., Teflon and carbon, than on materials having relatively high surface energies such as fused silica. At low oxygen concentrations [Ni(CO)4/O2 > 54 x 1031, apparently pure and well-formed nickel crystals were observed to nucleate and grow irrespective of the presence of oxygen. At higher concentrations of oxygen, a secondary growth process, dependent upon oxygen concentration and resulting in a gradual change in crystal morphology, was observed. It is concluded that the influence of oxygen on the nucleation and growth of nickel is determined by the relative kinetics of the various possible reactions, and that under the experimental conditions employed the 0-Ni interaction occurs at some nucleation or prenuclea-tion stage. THE purpose of the research on crystal nucleation in chemical vapor deposition as described in this paper has been twofold: 1) to examine some effects arising from the use of amorphous substrates, and 2) to study the specific effects of oxygen on the nucleation and growth of nickel in a nickel carbonyl-carbon monoxide system. The nickel-nickel carbonyl system was chosen for study for several reasons: 1) nickel films are of potential interest in electronic technology, and 2) the deposition can be carried out at moderate temperatures, thus making possible detailed study of the processes occurring and the use of a variety of substrate materials (including some which melt at relatively low temperatures). Fairly well-characterized chemical kinetics and a broad background of information are available on the py-rolysis reactions and on the mechanisms of Ni-O interactions. NUCLEATION AND GROWTH THEORY The theoretical background for the analysis of nucleation and growth by vapor deposition for a one-component system (physical vapor deposition) and the problems encountered therein have been reviewed by Hirth and pound.' More recently Mande12 has indicated the difficulties of applying such theory to chemical systems. One of the major problems involved is the possible multiplicity of chemical reactions and deposition routes. For example, those reactions which are probably of significance in a discussion of the pyrolytic deposition of nickel from nickel carbonyl under the conditions of the present experimental work are illustrated in Fig. 1. As is true with most cases of chemical deposition, many of the quantitative data necessary for a complete analysis of the system are either not available or not directly measurable. However, with the present system, sufficient data are available for a discussion of nucleation and growth on a qualitative basis. Classically, the rate of nucleation of a monatomic species being deposited from a vapor phase is given by

Jan 1, 1965

By F. H. Wilson, R. M. Brick

WITH the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45° to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections. The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the earing behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass. EARING BEHAVIOR OF BRASS Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (113)[112]. This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;* Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photograms for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By R. T. Hukki, A. M. Gaudin

Previous work on the principles of comminution has shown: (I) that the surface produced is proportional to work input (Rittinger law,1a-3); (2) that there is regularity to the weight distribution of the fragments according to size.4-10 In this paper it is brought out that the surface on the fragments is distributed in definite and simple relation to size. The experimental work has involved: I. Construction of an apparatus capable of measuring the surface of mineral fragments independently of the chemical composition of the fragments and independently of the site of the surface; 2. Refining the methods available for measurement of particle size; 3. Designing and building a crusher capable of operating on very small quantities of mineral, if necessary on single crystals, and in such fashion as to minimize handling losses of material. Complete experiments have been carried out with massive quartz and individual quartz crystals. partial experiments, lacking surface measurements, have been made with glass spheres, galena, sphalerite, fluo-rite, salt and coal. Introduction The existence of regularity in weight distribution with size was noted many years ago, especially by A. 0. Gates;' the subject was also studied in detail by one of us.6 In the latter paper it was shown that rocks can be divided into two classes: homogeneous rocks, which show no preferential breaking, and heterogeneous rocks, which show preferential breaking at the grain size of the rock. It was shown, furthermore, that the fragments obtained by rupturing a homogeneous rock occur (in the fine range) in such abundance as to permit the writing of a relatively simple equation to relate the weight retained on a screen to the screen opening. With screens of which the openings are in constant ratio, the weight retained, w, is related to the screen size x by the equation w = Cxm [I] In this equation C and m are experimental constants. A plot of weight retained against particle size is a straight line of slope m if the scales for x and w are both logarithmic. In the fine range, the slopes of the size-distribution graphs plotted according to the method described above vary within a limited range. An inspection of a number of size-distribution data by various experimenters indicates that the slope very seldom exceeds 1.0, but is usually greater than 0.7. More recently, schuhmann8 proposed a method of charting that has so many advantages of its own that it has been used primarily in this work. For fine particles Schuhmann has found that the data are represented by the equation (x)m k [2]

Jan 1, 1947

By A. M. Gaudin, R. T. Hukki

Previous work on the principles of comminution has shown: (I) that the surface produced is proportional to work input (Rittinger law,1a-3); (2) that there is regularity to the weight distribution of the fragments according to size.4-10 In this paper it is brought out that the surface on the fragments is distributed in definite and simple relation to size. The experimental work has involved: I. Construction of an apparatus capable of measuring the surface of mineral fragments independently of the chemical composition of the fragments and independently of the site of the surface; 2. Refining the methods available for measurement of particle size; 3. Designing and building a crusher capable of operating on very small quantities of mineral, if necessary on single crystals, and in such fashion as to minimize handling losses of material. Complete experiments have been carried out with massive quartz and individual quartz crystals. partial experiments, lacking surface measurements, have been made with glass spheres, galena, sphalerite, fluo-rite, salt and coal. Introduction The existence of regularity in weight distribution with size was noted many years ago, especially by A. 0. Gates;' the subject was also studied in detail by one of us.6 In the latter paper it was shown that rocks can be divided into two classes: homogeneous rocks, which show no preferential breaking, and heterogeneous rocks, which show preferential breaking at the grain size of the rock. It was shown, furthermore, that the fragments obtained by rupturing a homogeneous rock occur (in the fine range) in such abundance as to permit the writing of a relatively simple equation to relate the weight retained on a screen to the screen opening. With screens of which the openings are in constant ratio, the weight retained, w, is related to the screen size x by the equation w = Cxm [I] In this equation C and m are experimental constants. A plot of weight retained against particle size is a straight line of slope m if the scales for x and w are both logarithmic. In the fine range, the slopes of the size-distribution graphs plotted according to the method described above vary within a limited range. An inspection of a number of size-distribution data by various experimenters indicates that the slope very seldom exceeds 1.0, but is usually greater than 0.7. More recently, schuhmann8 proposed a method of charting that has so many advantages of its own that it has been used primarily in this work. For fine particles Schuhmann has found that the data are represented by the equation (x)m k [2]

Jan 1, 1947

By Michel T. Halbouty

South Texas, one of the world's important oil and gas-producing areas, continued to hold interest during 1939 as another scries of new fields and new producing levels was developed within its boundaries at a fairly continuous rate throughout the year. There were 1801 wells drilled in this area in 1939, compared to 1678 in 1938; of these, 1515 were drilled in established fields, or as extensions to proven areas (semi-wildcat), and 286 were drilled as rank wildcats, in search of new production. Among these rank wildcats, 22 produced oil, 7 produced distillate and gas and 257 were abandoned as dry holes (see Table 5). Of the 1515 field and cxtension wells, 1213 produced oil, or distillate and gas, 50 produced only gas and 252 were dry; 38 found new productive sand levels in proven ficlds. Jim Wells County led this district in discoveries, having had 9 new fields arid 9 new productive sands found within its border during 1939. Most activc of the 1939 discoveries were Reynold?; and Ben Bolt fields in Jim Wells County and Minnie Bock field in Nueccs County; among producing fields the most activc were: East White Point and Aransas Pass (McCampbell). Production from South Texas in 1939 totaled 55,105,506 bbl. against a total of 56,152,122 bbl. produced in 1938. South Texas should continue its present rate of developrnent and exploration and this should result in the discovery of many fields in its numerous oil-bearing zones, and should also lead to more knowledge of the possibilities of its deeper horizons, such as the Mt. Selman and Wilcox formations; with the latter holding particular interest at the present time. Tide Water Associated Oil Company's A. M. Bruni No. I, Cole-Bruni field, Webb County, the deepest well drilled along the Mirando trend, was carried to 8959 ft., where it started to blow out from a Wilcox sand topped at 8954 ft., making gas, distillate and mud under heavy pressure. After the well was killed, drill stem beeame stuck and was cemented in place in order to test a Queen City (Mt. Selman) sand logged from 5620 to 5675 ft. This and other shows found in other wells along this trend, but out of this district, have served to increase the importance of this but little explored Sparta-Wilcox trend of South Texas during the year, and more activity along it is to be expected in the near future.

Jan 1, 1940

By Michel T. Halbouty

South Texas, one of the world's important oil and gas-producing areas, continued to hold interest during 1939 as another scries of new fields and new producing levels was developed within its boundaries at a fairly continuous rate throughout the year. There were 1801 wells drilled in this area in 1939, compared to 1678 in 1938; of these, 1515 were drilled in established fields, or as extensions to proven areas (semi-wildcat), and 286 were drilled as rank wildcats, in search of new production. Among these rank wildcats, 22 produced oil, 7 produced distillate and gas and 257 were abandoned as dry holes (see Table 5). Of the 1515 field and cxtension wells, 1213 produced oil, or distillate and gas, 50 produced only gas and 252 were dry; 38 found new productive sand levels in proven ficlds. Jim Wells County led this district in discoveries, having had 9 new fields arid 9 new productive sands found within its border during 1939. Most activc of the 1939 discoveries were Reynold?; and Ben Bolt fields in Jim Wells County and Minnie Bock field in Nueccs County; among producing fields the most activc were: East White Point and Aransas Pass (McCampbell). Production from South Texas in 1939 totaled 55,105,506 bbl. against a total of 56,152,122 bbl. produced in 1938. South Texas should continue its present rate of developrnent and exploration and this should result in the discovery of many fields in its numerous oil-bearing zones, and should also lead to more knowledge of the possibilities of its deeper horizons, such as the Mt. Selman and Wilcox formations; with the latter holding particular interest at the present time. Tide Water Associated Oil Company's A. M. Bruni No. I, Cole-Bruni field, Webb County, the deepest well drilled along the Mirando trend, was carried to 8959 ft., where it started to blow out from a Wilcox sand topped at 8954 ft., making gas, distillate and mud under heavy pressure. After the well was killed, drill stem beeame stuck and was cemented in place in order to test a Queen City (Mt. Selman) sand logged from 5620 to 5675 ft. This and other shows found in other wells along this trend, but out of this district, have served to increase the importance of this but little explored Sparta-Wilcox trend of South Texas during the year, and more activity along it is to be expected in the near future.

Jan 1, 1940

By Gerald Edmunds

In a paper1 before this Institute in 1940, the writer reported that the surface orientation texture of zinc and cadmium differed from the texture existing within the casting, in that basal planes were parallel to the surface. He was unable to rationalize the , origin of this surface texture. It is conceivable that the surface orientation texture is influenced by the atomic force fields, which are different at the surface and within the body of metal. It was considered that a radical changc in the surface against which the metal is cast might alter the surface texture. In trial of this, zinc has been cast against a surface of molten lead, but the same result has been obtained—i.e., (001) parallel, ± 2oo, to the surface—as was obtained when it was cast against air, Transite or iron.' Into the bottom of an open cast-iron tray, 7 by 14 in. by 2 in. deep, preheated to about 275°C., about 1/4 in. of lead, then 1/2 in. of zinc was poured, and the whole was covered with an electric heater to enforce freezing from the bottom upward. After a lapse of time sufficient for the zinc but not the lead to solidify, the zinc slab was raised free of the molten lead. The bottom surface of the zinc casting was coated with a thin layer of lead. A specimen of the slab 136 in. square was metallographically polished to flatten it and remove the slight film of lead, and the orientation was determined by the method used before,' with the result stated above. Some determinations have also been made on other metals, as follows: Surface orientation determinations were made on the 3/8-in. diameter grip section of two 1/4-in. diameter aluminum-alloy die-cast tensile bars and on a 1/8 by 1/2-in. flat aluminum-alloy die-cast tensile bar. None of these three aluminum die castings exhibited any preferred orientation at the surface. A brass die casting (nominal composition: 60 Cu, 37.75 Zn, 1.00 Sn, 1.00 Pb, 0.10 Al, 0.15 Si) furnished by C. S. Smith was also examined. The surface showed a random orientation of alpha and beta. Summary A zinc casting solidified against a molten lead surface was found to have the same surface orientation texture, (001) parallel to the surface, as other zinc and cadmium castings. Aluminum and alpha-beta brass die castings were found to have random grain orientation textures at the surface. Acknowledgment The X-ray determinations were conducted by M. L. Fuller.

Jan 1, 1945

By D. Turnbull, J. H. Hollomon, J. C. Fisher

UNDERSTANDING of the diffusion problem has recently been furthered by the analysis of Birchenall and Mehl.1 They pursued the problem of the variation of the diffusion coefficient with composition for non-ideal solid solutions. Their analysis follows the tradition of Wagner,2 Jost,3 Dehlinger,4 and Darken,' who assumed the net flux of dif¬fusing material to be proportional to the gradient of a quantity related to free energy. The basic assumption in Birchenall and Mehl's formulation of the problem is that the net flux of diffusing material is proportional to a thermodynamic activity gradient. To estimate the applicability of the derived relations, they corrected the diffusion coefficients of carbon in austenite by utilizing Smith's' activity data for carbon, and the diffusion coefficients for zinc in copper with activity data computed from the vapor pressure measurements of Hargreaves.7 The corrected coefficients for carbon were virtually independent of carbon concentration. For the diffusion of zinc in copper a moderate variation of diffusion coefficient with concentration remained after the correction. The problem of diffusion can be formulated in another way than that used by Birchenall and Mehl. The method is that of chemical rate theory and has been used by Eyring and his coworkers8,9 as well as by Eyring and Zwolinski10 in a discussion to Birchenall and Mehl's paper. As yet the method has not been applied to substitutional solid solutions. On the basis of their assumptions, Eyring and Zwolinski derived a relation between the diffusion coefficient and activity that is identical with that of Dehlinger and Darken but which does not correct for the variation of the diffusion coefficient with concentration as well as does the relation derived by Birchenall and Mehl. It was thought that the theory of diffusion would be more complete if the inconsistency between the two analyses could be rationalized and if diffusion in substitutional alloys were analyzed on the basis of the concepts of the chemical rate theory. CHEMICAL RATE THEORY According to the theory of absolute reaction rates8 the reaction [A,+A2+ ... +.A;->X,+X2 +...+X; EqI] is viewed as taking place in two steps. First the reactants A1, A2, . . . A[i] combine to form an activated complex M with which they are in equilibrium; [A, + A2 + .. . + Ai = M. Eq 2] Second the activated complex decomposes to give the products X1, X2. . .. X[j]; [M->X1+X2+ ... +.X;. Eq3] It has been shown8 that the number of activated complexes decomposing per unit volume per unit time is given by the expression† [kT]

Jan 1, 1948

By G. H. Ruggles

POPULAR opinion, as it might be termed, has always been of the trend that a flotation reagent added to the ball mill during grinding would be more thoroughly mixed with the pulp and for that reason more effective in the production of low tailing. That there are other effects, inimical to good flotation, when using so-called chemical reagents, is brought out by the series of tests outlined in Table 2. It was defi-nitely proved that if either the T. T. mixture (20 per cent thiocarbanalid-80 per cent orthotoluidin) or po-tassium xanthate were added to the ball mill the result-ing flotation concentrate would be lower in copper and higher in insoluble than the concentrate produced by adding these same reagents without the ball mill cir-cuit. With the T. T. mixture four sets of tests were made. The screen analyses of the flotation feed show that there was very little difference in the original grind-ing. When the T. T. mixture was added to the head of the flotation machine the flotation concentrate had a little over 61 per cent solids -200 mesh. If the mix-ture was put into the ball mill the flotation concentrate had but 40.7 per cent of the solids -200 mesh for one set of tests, and 49.0 per cent for the other set. With the mixture at the head of flotation the total concen-trate was high in copper (34.715 and 36.525 per cent) and low in insoluble (13.20 and 11.61 per cent). The assay of the concentrate when the T. T. mixture was introduced into the ball mill was what might be termed low in copper (29.389 and 30.833 per cent). In one of these 'sets of tests (periods 8 to 11, third column) the insoluble was high, 16.81 per cent. The other run (peri-ods 12 to 15, fourth column) for some unknown reason shows a low insoluble, 12.72 per cent. With similar grinding the addition of potassium xan-thate to flotation produced a concentrate having 62.8 per cent -200 mesh, whereas with the potassium xanthate added to the ball mill the flotation concentrate was very coarse, only 36.4 per cent passing 200 mesh. The difference in the total assay of the concentrate is remarkable ; 35.847 per cent copper when the xanthate went to flotation and 30.44 per cent copper when the xanthate was added to the ball mill; insoluble, 10.94 per cent in the former instance, as 22.15 per cent in the latter.

Jan 8, 1927

By J. W. Spretnak, G. W. Cunningham

Grain growth across the bond region in Pressure bonded copper was found to be mainly dependent upon the presence or absence of microvoids, but it was also found that prior history, bonding pressure, bonding time, and bonding temperature are important variables. An increase in pressure, time, or temperature tends to promote grain growth in the interfacial region. Polygonization is observed after pressure bonding except for specimens previously annealed at temperatures on the order of 1800°F or higher. The dislocation density in bonded specimens was found to be greater in the bond region. THE bonding of metals by the application of gas pressure at elevated temperatures is a relatively new process, having been developed over the past 10 years. The technique, as described by Paprocki, Hodge, and Boyer,l is unique in that assemblies of many parts and complex shapes can be bonded with a negligible amount of deformation. The process thus differs metallurgically from pressure welding, cold welding, and recrystallization welding in that deformation occurs only in a microscopic region whereas, in general, the welding requires severe deformation and may extend the contact surface by a factor of 3 to 10 during the welding. From a practical standpoint, pressure welding is not amenable for bonding large surfaces. During the time in which Paprocki and coworkers were deve1oping the process, West2 established aproc-ess,for bonding aluminum to uranium, and Barnes and Maze? developed a gas-pressure-bonding technique for nickel and copper. Recently, Fugardi and Zambro4 have used equipment similar to that developed by Paprocki and coworkers to establish parameters for bonding stainless steel, aluminum, and zirconium. Most of the investigations on pressure bonding have been empirical in nature and, although methods have been developed for bonding such metals as molybdenum, columbium, titanium, zirconium, and stainless steel, the information concerning the mechanism of bonding is limited. Several workers5"7 have studied the pressure bonding of dissimilar metals in order to gain information on diffusion and formation of inter-metallic phases under application of pressure. Clapson and Robbins8 have shown by a series of annealing studies that voids in the interfacial boundary of roll-bonded copper can prevent movement of the boundary until the voids are spaced far enough apart to prevent pinning. They also indicated that recrystallization and grain growth can eliminate the voids. In this paper it is shown that voids are the major detriment to grain growth across pressure-bonded interfaces, but it is also shown that prior history, bonding pressure, bonding time, and bonding temperature are

Jan 1, 1962

By K. L. Clark, Nicholas Kowall

MAXIMUM furnace efficiency and close control of final steel composition demand that the steel melter be able to follow closely the variations in the carbon content of the bath. For many years, the fracture test has been used by melters for estimating carbon, because it requires only a very short time to pour a sample into a chill mold, cool it in water, break it with a sledge hammer, and observe the fracture. After long experience gained from the observation of such fractures, most melters are able to estimate the carbon content of steel with amazing accuracy, particularly in the lower carbon ranges. Notwithstanding the utility of the fracture test, there has been widespread interest in other methods for rapid carbon determination to supplement it and to ensure against possible errors in human judgment. Several methods, based upon measurement of magnetic properties as functions of carbon content, have been described in the literature1-6 and have been found to give reasonably reliable results in plant practice when scrap composition is known and controlled. A difficulty encountered in the use of analyzers of the magnetic type is that alloying elements do change the relationship between carbon content and magnetic properties and it becomes necessary to establish calibration curves for all the expected combinations of alloy residuals that are not oxidized in the bath. The work reported here is of an investigation of a method that is independent of alloying elements normally present in constructional steels, being based upon the relatively well-known fact that in plain carbon and low-alloy steels martensitic hardness is a function of carbon content alone. WORK OF OTHER INVESTIGATORS In 1938, Burns, Moore and Archer published a curve7 that showed that the hardness of martensite is a function of carbon from 0.10 to 0.50 per cent and is independent of grain size or alloy content, at least within the range found in constructional S.A.E. compositions. Some of the deeper hardening types investigated, however, contained carbon to a maximum of only 0.20 per cent. Using this principle, Kern8 developed a method of rapid carbon determination for S.A.E. 43xx steels. His procedure consisted of chill-casting a test bar that was large enough to give a surface that could be prepared for Brinell indentations. The test piece was quenched immediately after solidification was complete and hardness readings were taken, so that the carbon content could be read from an experimentally determined curve giving the relationship between as-quenched hardness and carbon. EXPERIMENTAL WORK Although Kern's work had been done with a relatively deep-hardening steel, it

Jan 1, 1944

The ability of activated charcoal or carbon to adsorb complex metal ions has been recognized for many years, but it wasn't until the late 1940s and early 1950s that attempts were made to employ carbon-In-Pulp or C. I. P. processing to the recovery of gold. Early plants using the process were those at the Golden Cycle in Cripple Creek, Colorado, the Getchell Mine near Golconda, Nevada, and at the Idria Mine in Honduras. Recovery of the carbon from the pulp was done by screening or flotation, and recovery of gold from the carbon was done by burning the carbon (a very difficult task) or by sending it to a smelter. Unfortunately at the time, the price of gold was still fixed at $3-5 per ounce and labor costs were rising to the point where these mines were no longer able to operate. Consequently, C. I. P. treatment was temporarily forgotten. In the early 1970s, however, Homestake Mining Company at Lead, South Dakota, were being forced by environmental regulations to discontinue the use of mercury for amalgamation in their 7,500 ton per day plant, and at the same time were encountering high labor costs in the slime circuit of the plant, where over 2,000 tons of slimes were filtered each day in Merrill plate and frame filter presses. Shortly before that, researchers of the United States Bureau of Mines had developed the caustic -cyanide method of stripping gold from activated carbon and an electrolytic cell (now known as the Zadra cell) to recover gold from the carbon strip liquor. Homestake and the United States Bureau of Mines then jointly operated a C. I. P. pilot plant at Lead. Results were immediately favorable and a 2,400 ton per day C. I. P. plant was then built to treat the slime fraction of the Homestake ore. (See Au and Ag Cyanidation Plant Practice, Volume I, SME of AIME, 1975. Later, Homestake built a second plant at Creede, Colorado, to treat the slime fraction of the tailings from a silver-lead flotation plant. Next was Duval Corporation's 3,000 ton per day C. I. P. plant at Battle Mountain, Nevada. Both of these latter plants are described in this volume. C. I. P. operations under construction at the time of this writing are as follows: Pinson Mining Co. , Nevada Gold Freeport Gold Company, Nevada Gold Compania Minera El Indio, Chile. Silver and Gold

Jan 1, 1981

By B. J. Harlan

The trying times experienced by the steel industry during the past four years have emphasized the necessity of producing pig iron at the lowest possible cost. The trend in both design and operation of blast furnaces has been toward this end rather than toward securing maximum production from a unit or group of units. In the following discussion the trend in design of stacks and auxiliary equipment will be taken up before operation is considered. Although few furnaces have been constructed in the past few years, the trend is definitely toward larger furnaces with a hearth diameter of 24 or 25 ft. Such a furnace is very flexible, being able to produce efficiently any desired daily tonnage between 500 and-1000 or more. The detail of the design of furnace stacks, with the exception of the top, has changed little in recent years. To decrease the velocity of gas through the throat of the furnaces, thereby reducing flue-dust losses, the stock-line areas are constantly being made larger. The top dimensions of the larger furnaces are usually as follows: Stock-line diameter, 19 to 20 ft.; large bell diameter, 14 to 15 ft.; straight section of throat, 5 to 10 ft. high; inwall batter, 1 to 11/4 in. Pe ft. The ratio between the area of the stock line and the area of the large. bell is usually about 1.85 to 1. The stock-line diameter of some smaller furnaces has been increased to that of the hearth diameter of the stack at the expense of the stack batter. Remarkable decreases in flue-dust production are claimed for the so-called " Venturi top," which is achieved by flaring the stock line, in the form of an inverted cone, from a diameter of 17 ft. at 10 ft. below the large bell closed to a diameter of 19 ft. 6 in. at 3 ft. below the large bell closed. Time alone will tell which of the two designs is the better. Because of differences in raw materials, one top may be better for some plants and the other top for other plants. In the search for lower costs and higher efficiencies all operators are, adopting stoves that will maintain maximum hot-blast temperatures with a minimum gas consumption. To meet these requirements, stove capacity of approximately 7 sq. ft. of heating surface and 1.8 cu. ft. of brick volume is required per cubic foot of wind blown per minute.

Jan 1, 1934

By Willard Jillson

WITHIN the last ten years Kentucky has become celebrated for its low-sulfur bituminous coals. Prior to this time, many investigators had discovered the abundance of this coal but the fact was unknown to the general public until the last extension of Kentucky's mountain railroads was completed. The coals of Kentucky are, broadly, separated into two geographic units-the eastern and the western coal fields. On a basis of their sulfur content these coal fields fall into three units, which are indicated on the accompanying map, by numbers, 1, 2, and 3. The area marked 1, the very southeastern part of the State, shows the lowest sulfur, all coals being averaged. In this field the maximum is 1.04 per cent. and the minimum as low as 0.68 per cent.-both averages and not individual analyses, which would of course show much greater variation. Included in this group are the following counties: Lawrence, 0.87 per cent.; Martin, 0.75 per cent.; Johnson, 0.73 per cent.; Magoffin, 0.S7 per cent.; Floyd, 0.88 per cent.; Pike, 0.68 per cent.; Knott, 1.04 per cent.; Perry, 0.77 per cent.; Letcher, 0.80 per cent.; Leslie, 0.70 per cent.; Harlan, 0.79 per cent.; Knox, 0.86 per cent.; and Bell, 0.92 per cent. The total average sulfur content for these thirteen counties is 0.82 per cent. Bordering the restricted low-sulfur field of eastern Kentucky is the No. 2 belt (slightly darker), which is commonly known as the western border of the eastern coal field. Here the maximum sulfur is 2.91 per cent. and the minimum 1.05 per cent. Again these are averages and not individual analyses. The counties in this group are: Greenup, 2.60 per cent.; Boyd, 1.67 per cent.; Carter, 1.07 per cent.; Morgan, 1.40 per cent.; Wolfe, 1.83 per cent.; Lee, 2.93 per cent.; Breathitt, 1.85. per cent.; Owsley, 1.09 per cent.; Jackson, 1.06 per cent.; Rockcastle, 2.30 per cent.; Clay, 1.09 per cent.; Laurel, 1.08 per cent.; Pulaski, 2.24 per cent.; Whitley, 1.05 per cent.; McCreary, 1.50 per cent.; and Wayne. The sulfur percentage average for this area including fifteen important counties is 1.65 per cent.

Jan 9, 1919

By R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-C and Fe-Ni solid-solution alloys has been investigated at 25°C. It is found that the rate of solid-solution strengthening is dependent upon the strain at which the yield stress is measured, the macroyield stress being much more concentration-dependent than the microyield stress. In fact the addition of nickel does not lead to any increase in the microyield stress of iron. The primary effect of increasing the carbon or nickel content is to increase the slope of the stress-strain curve in the microyield region; this effect has been correlated, by means of transmission electron microscopy, with a decreased ability of the dislocations to cross-slip. It is concluded that the Mott-Nabarro theory is a good description of true solid-solution hardening in these and other iron-base alloys. A.LL theories of the solid-solution strengthening1-4 indicate that the flow stress of an alloy increases both with solute concentration and "misfit" between the solvent and solute atoms. The functional relationship between strength, solute concentration, C, and misfit depends upon the particular theory. Mott and Nabarro1,2 and Schoeck and Seeger3 both predict a linear increase in strength with concentration, while Fleischer4 indicates that the strength should be proportional to C1/2; there are in the literature experimental observations to support both these compositional dependencies.1'8 The experimental evidence used to support the theories is the change in macroscopic yield stress (strain, e, = 10-3) with composition. However, recent investigations have revealed that solid-solution strengthening in a Cu-Al single crystals7 and in Fe-V polycrystal-line" alloys depends upon the strain at which the flow stress is measured; a flow stress in the microplastic range (e = 10-6 to 10-5) is much less concentration-dependent than the macroyield stress. Since the theories of solid-solution strengthening are concerned in particular with the stress to move a dislocation in a dislocation-free matrix, they should only be compared with microyield-stress data; it will be shown that in a material deforming homogeneously the microyield stress (e = 10-6) is approximately the stress to move through the matrix those dislocations which have been nucleated by stress concentrations such as particles or grain boundary ledges.9-11 In contrast, the macro-yield stress is more complex in that it is affected by several phenomena: dislocation multiplication, dislocation interactions, and the ease of propagating slip across grain boundaries. For example, it is experimentally observed that when long-range order12'13 or solute effects10 restrict cross alip the grain boundary

Jan 1, 1967

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947

By G. A. Crowe, W. T. Bishop

WHILE the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,2 by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,3 cadmium,3.4 cobalt,4 copper,3-9 gold,10 iron,3,11 lead, 3,12,13 molybdenum," nickel,4.8,9 tin,15 and zinc3,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. PRINCIPLE OF THE METHOD The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1946