Search Documents

By Fernando Henrique Gomes de Souza

Techniques which use a spring to supply the bias force to actuator are well adopted since they are inexpensive and simple to construct. In this work it was design an actuator concept using bias-type device technique, which comprises two coils that mutually push against each other to supply the stroke. For the coils springs, it was used a wire of NiTi shape memory alloys (SMA) and a wire of 400 grade maraging steel as construction materials.

Aug 8, 2018

By José Divo Bressan

Present work examines material surface damage by cavitation erosion of metals or the wear phenomenon from water bubbles collapse near the metallic surface. Material surface damage by cavitation erosion is due to wear mechanisms of liquid micro-jets impingement and shock waves. Experimental cavitation in tap water was investigated, using the proposed new design of compact rotating disk equipment. In this device, a rotating disk with cavitation inducers and specimens fixed on it ran in tap water to provide cavitating flow at constant high speed of 47.9 m/s similar to service conditions in pumps and propellers. Two types of cavitation inducers in the rotating disk were investigated: through-holes and pins. Carburized cast iron, aluminum, brass and bronze specimens were tested in this device. The cavitation damage mechanisms were observed by scanning electron microscope. Surface damage in the specimens was measured by mass loss and plotted in graphs of mass loss versus running time. After 25 hours testing, the specimens surface showed pitting formation and mass loss. All specimens presented surface damage: pit diameter size was about 100 or 150 to 300 micron. In aluminum specimen, damages by burned pit formation and plastic deformation could be seen, however, the mass loss was lower than the expected, possibly due to alumina film formation. Present equipment had quite good test reproducibility when compared with results from literature.

Jul 31, 2018

By Uwe König

Traditionally quality control of iron ore sinter, its raw materials and raw mixtures has relied on time-consuming wet chemistry. The mineralogical composition that defines the properties is often not monitored. XRD analysis in combination with Rietveld quantification and statistical data evaluation using Partial Least-Square Regression (PLSR) has been successfully established to determine the mineralogical composition and process parameters such as the FeO (Fe2+) content and basicity of iron sinter within an analysis time of less than 8 minutes per sample. Both methods take the full XRD pattern into account and can be simultaneously applied on the same measurement. In addition the Rietveld method was used to quantify the phase content of raw mixtures to monitor the composition of blending beds.

Aug 16, 2017

By Hui-bin Wu, Rui Yuan, Yang Gu, Peng-cheng Zhang, Zheng-zhi Zhao

The corrosion behavior of three kinds of medium-Cr rolled steel pipeline steels in carbon dioxide collecting and transporting environment at different temperatures was studied. The results shew that the 5Cr sample was most affected by temperature. When the temperature rised from 30 °C to 90 °C, the corrosion rate increased from 0.12 mm/a to 1.87 mm/a, which was increased 15.6 times. The corrosion rate of 7Cr steel at 30 °C was similar to that of 5Cr steel. However, as the temperature increased, the corrosion rate rised slowly, increasing by 2.4 times at 90 °C. The corrosion rate of 9Cr steel was not obvious with temperature, and it was always below 0.06 mm/a. The thickness of the corrosion product film of the three samples gradually increased below 70 °C, and suddenly increased above 70 °C. This was related to the negative temperature coefficient of the solubility of FeCO3, and the thickening of the product film also affected the ion exchange of the cathodic reaction. An increase in the Cr content contributed to grain refinement and increased the proportion of the small-angle grain boundaries. More fine grains mean an increase in the total length of the grain boundaries, which could provide a diffusion channel for the free Cr element; on the other hand, the low-angle grain boundary structure was more orderly, with a lower free volume and lower interface energy. Under the combined effect of both, 9Cr steel and 7Cr steel had high volta potential and better corrosion

Oct 1, 2019

By Valdicleide Silva Mello

Nowadays the biodiesel use is obligate in Brazil, in order to reduce the emissions of fuel burn. However, it is important to analyze which percentage of biodiesel is necessary to keep or improve the lubricant action of fuel for diesel engine, as well which kind of biodiesel give better performance. Therefore, this work aims to analyze the parameters that keep the lubricant action of biofuels, by using the Box-Behnken design type to optimize them. In this design was evaluated the input parameters: the type of the biodiesel (soybean, sunflower and palm), the concentration (5%, 20% and 100%) and the temperature of contact (25°C, 40°C and 60°C). The analyzed output parameters were the percentage of film formation, coefficient of friction, wear scar diameter (WSD) of ball, these output parameters were obtained by HFRR tribometer and they were analyzed applying response surface methodology. With this methodology was possible to determine the simultaneous influence and the interactions between two or more independent variables investigated. The response surfaces generated for the coefficients of friction, WSD, film formation showed a higher lubricant action for higher levels of concentration of biodiesel. An increase in lubricant action was found to high and intermediate temperature.

Jul 31, 2018

By Benito Barbabela Silva, Michel Garant, Mathieu Dubé

Pellets market challenging scenario has stimulated pelletizing experts to pursue innovative alternatives to process development in order to increase pellets competitiveness vis-à-vis sinter. When it comes to indurating process, pelletizing productivity is still limited and its OPEX inflated by the lower input of carbon into mixes due to quality impairment caused by magnetite formation in pellets core. This obstacle led to the rethinking of carbon distribution strategy within the green balls. To achieve such purposes, COREM through its precompetitive research program dedicated to its members, has proposed the layered pellets®, a two-stage balling technology. Balling in disc and pot-grate tests in COREM’s pilot plant were carried out to proof the concept, support the arising technology and evaluate its potential. According to first results, while CCS strongly improved, tumble and abrasion indexes as well dynamic LTD must be further investigated. Tests on four classes of equivalent carbon content pellets to evaluate layering strategy gave very good perspectives concerning the increase of productivity, and the reduction of fuel consumption and GHG emissions.

Oct 1, 2019

By Daniel Suarez

Over the last few years the mining industry has continuously been facing increases in capital and operating costs for new projects; plant expansions and also significant increases in the operating costs of existing plants. To counteract such trend the industry is seeking technologies such as the Vertimill as an option to lower the operating costs of grinding circuits. The benefits the Vertimill offers in terms of lower energy consumption and lower media consumption are well established and documented; such benefits can significantly improve the viability of a new project, plant expansions or upgrading grinding mills that need to be replaced. The paper briefly describes the operation of the Vertimill, recent regrind applications in processing Iron ores where the impact of lower energy and grinding media consumption is very significant because of the large tonnages involved, and also applications as a tertiary and secondary grinding stages of grinding circuits. The paper also highlight the expected role the Vertimill can play in secondary applications and the expected impact on the overall economics of the project.

Aug 1, 2018

By John Malcolm Gray

Interest in X-80 linepipe steels emerged in the early 1980’s and it was first used in 1985 by Ruhr Gas [1]. The early steels were extensions of conventional Nb-V or Nb-Mo microalloyed X-70 steels but other alloying concepts emerged based on Nb-Mo-B alloying (NKSTAF [2] and ULCB [3]). The latter had acicular ferrite/bainitic microstructures and carbon contents below 0.05 percent. In parallel renewed interest developed in ultra low carbon (0.02 percent) higher niobium steels which had first been studied in 1962 [4]. Such steels exhibited excellent notch toughness when processed with high finish rolling temperatures (>950°C) which made them suitable for processing on weak, older rolling mills. With time such steels, designated “High Temperature Processed”, or HTP steels, were further optimized and produced in modern, very strong rolling mills due to their superior economy compared with traditional vanadium and molybdenum containing steels. The chronology of the HTP development is presented in the present paper. Full scale demonstration heats of a 0.06 percent carbon 0.10 percent niobium steel were produced by Bofors Steel Plant in 1972 and were converted from slabs to plates by nine different steel mills [5-7]. Commercial application in API Grade X-70 first occurred in Canada in 1974 [8,9] but the concept was only used sporadically after that until 1998 when it was applied for the API Grade X-70 Sour Service Cantarell Project [10] in Mexico. Soon thereafter, the El Paso Cheyenne Plains Project used a 0.05%C 0.095%Nb 0.27%Cr variant of the HTP steel [10-12]. Nowadays the HTP concept is being utilized for construction of approximately 6000 km of 48” OD x 18.4 mm X-80 per year in China. The metallurgical principles and history of the development are presented in details in this paper.

Aug 7, 2018

By Johan Richaud

Achieving high surface quality steel in the continuous casting process requires optimal mould level control. The design of the casting channel from the tundish to the mould is crucial to prevent formation of undesired instabilities or biased flows that can cause level fluctuation. With the aid of CFD and with physical water models, the geometry of the stopper nose and the nozzle seat have been studied and optimized to improve the overall mould flow stability. A special stopper nose; Ripple Stopper (RST), has been developed that reduces the formation of large and unwanted eddies in the liquid steel that destabilize the port exiting jets. Instead, the RST produces a fast release of turbulence in the form of a large number of small eddies. The large sudden fluctuations in the mould level are reduced, which in turn reduces the occurrence of surface defects. An additional benefit is derived from the local pressure around the stopper nose region being greater which reduces the refractory erosion. For a tundish gate type flow regulation, a new design encompasses an offset in the Tundish Well Nozzle (TWN) that realigns the flow and reduces the bias flow that is common to tundish gate regulation. The steel recirculation regions below the throttling gate are decreased reducing the risk of oxide depositions. The RST and the Offset bore casting channel have been applied successfully leading to a superior flow control performance between the tundish and the mould.

Jul 30, 2018

By Gilmar Ferreira Bataglia

The possibility of parameterization of hot tensile data together with creep data is investigated, for Aluminium Alloy 7475-T7351. This study represents part of a broader research program aiming at the validation of a methodology recently proposed for analyzing both kinds of data together, considering different metallic materials. The results presented in Part 1 of this work, were analyzed according to 4 traditional methods of the literature for parameterization of creep data, namely: Larson-Miller, Orr-Sherby-Dorn, Manson-Succop and Manson-Hafferd. The compatibility of the hot tensile test results with those of creep is remarkably good, indicating the possibility of using both kind of data together also in extrapolation schemes. The criterion proposed for equivalence between hot tensile and creep data is verified to work well also for this kind of material, under the present experimental conditions.

Aug 8, 2018

By Sander Mul, Michael Brandner, Armin Paar

Graphitic HSS roll grades such as ESW’s brand VANIMO can be considered as the latest developments for the last finishing stands in hot strip mills. These roll grades are developed on the basis of the alloying concept of (Carbide Enhanced) Indefinite Chill work roll materials. During the development of VANIMO, the amounts and types of carbide forming elements were increased and adjusted into the direction of cast HSS roll grades. The microstructure of graphitic HSS roll grades therefore consists of tempered martensite, cementite and several different carbide types as well as a well-defined amount of free graphite. The main purpose of graphitic HSS roll grades is to combine the high surface quality of Indefinite Chill alloys as well as the high wear resistance of HSS roll grades. Several systematic steps were taken to increase the wear performance from Carbide-Enhanced Indefinite Chill grades to the more advanced VANIC grade and further on to the highest alloyed roll grade VANIMO. In every development step, the surface quality of the roll grades was carefully monitored. The decision to invest in new testing equipment at ESW’s plant was driven by the wish to see microstructural effects of different alloys in a macroscopic dimension. Usually samples are taken from cast rolls and investigation is done in comparably small areas compared to the total surface of a roll. Rolling of strip is done with the entire barrel, so effects of alloy and microstructure can appear anywhere on the barrel surface. To ensure better understanding and deeper knowledge about influences of alloying trials we decided to install the last version of LRI (Lismar Roll Inspection). LRI includes the latest technology of Eddy Current with an enormous resolution. Depending on the formation of carbide precipitations, carbide network as well as matrix and free graphite, the EC test can detect smallest differences. The possibility to analyze the different results of EC and UT surface wave inspection will be discussed. A few examples of surface effects in the mill application will be discussed and improvement strategies explained.

Oct 1, 2019

By Stefan Wahlund, Tom Adams, Mats Söder, Zhi Zhang

By applying high-end rolls with utmost performance and superior surface quality, hot strip mills can be further optimized. Operations in the mill have been also waiting for improved roll solutions that can minimize required roll changes which impact production efficiency. Limitations are usually due to the low performance and surface degradation of the rolls in the late finishing stands (F5 – F7). VICTURATM is the most recent developed grade for rolls utilized in the late finishing stand at Union Electric Åkers (UEÅ). These rolls have been tested and applied in mills all over the world. A significant improvement over the enhanced ICDP rolls has been observed. Hot strip mills are realizing improved operating efficiency and Total Cost of Ownership (TCO) through the transition of their entire roll inventories to these break-through products.

Oct 1, 2019

By Werner Klein

The utilization of production facilities in an optimum way, with reliable due date fulfillment, reducing raw material and energy consumption, are challenges iron and steel companies are facing in their business every day. By using an APS system such goals can be achieved to increase the competiveness of iron and steel producers. A sophisticated APS supports the overall planning process by applying complex rules based on product and order mix, its production routings with corresponding processing and transport times and resource availability. Specific technological as well as steel grade and energy related constraints are also considered to meet company specific KPIs. A core feature of APS solution is to react online on deviations to plan during the production process. Deviations such as nonconformance of intermediate material attached to an order, sudden production delays, unavailability of important production resources, makes it necessary to update the production plan. In general the task of APS is to support the preferred work-to-order concept, by assigning work-orders to available production facilities along the product specific process route and generate optimized material sequences for critical work centers.

Aug 17, 2017

By Alberto Lainati

The Bar Reducing and Sizing Technology has a core function in the value-chain for the production of rolled SBQ (Special Bar Quality) products. The EVO 2+4-roll is based on the compact combination of a 2-roll high-reduction module followed by a 4- roll low-reduction module for precise sizing. The EVO 2+4-roll mill, allows to gain significant technical and economical advantages in the hot- and post-rolling process routes: dimensional and surface accuracy, quick adaptability to processing variances and to small lots requirements, superior technological features of as-rolled product, competitive capex and opex. The EVO 2+4 unit has a very compact design, which makes it suitable both for new mills and upgrade applications.

Aug 17, 2017

By Douglas Glenn Stalheim

Hot strip structural steel coil used in construction, engineering, transport, structural applications and other applications are widely used in yield strengths from 300 – 700 MPa. However, structural design engineers are now not only requiring various strength levels but also other mechanical properties, primarily good formability, toughness and weldability. To produce a balanced approach to a cost effective structural steel, hot strip coil requires an understanding of utilization of an optimized alloy composition designed for the layout/equipment capabilities of a given hot strip mill to produce the desired metallurgy for optimum mechanical property performance. The term “cost effective” does not just focus on alloy design, but also ease of overall processing from steelmaking, casting, rolling and cooling, stable mechanical properties with a statistically normal distribution, no downgrades/rejections and a product that the end user recognizes as being superior to others. The desired metallurgy is simply understanding what will be the optimum microstructure and cross sectional grain size/distribution needed to meet the mechanical property requirements. This paper is a follow up paper that previously described optimum base alloy designs along with steelmaking/casting processing considerations and will focus on proper reheating, rolling and cooling metallurgy/processing strategies to produce quality cost effective hot strip structural steel coil.

Aug 17, 2017

By Ernst Lindemann

Steel suppliers are required to deliver sheets with particular qualities and with lightweight-potential to the automotive industry. New types of steel call for new production processes. SMS group has developed a new micro-mill-concept, the core of which is the belt caster. This was first built on an industrial scale and has been put into operation and developed together with Salzgitter Flachstahl GmbH. The robustness in industrial-scale operation could be verified. The full use of the belt casting technology, mainly related to energy efficiency and CO2 reduction, is realized with the micro-mill-concept. This is an in-line-process, casting and rolling in one line.

Aug 17, 2017

By Luke A. Balzan

Access to information is a key component for making improvements to any process. This is particularly true for all aspects of the iron mining and steelmaking process. The ability to make rapid control decisions can significantly influence process outcomes, including ensuring product specification, mining quality, transportation limits, upgrade factors, waste bypass and direct shipping, among many others. While traditional laboratory methods provide feedback for such processes, having access to analysis results in real-time can lead to positive reactive and predictive control decisions to be made rapidly, leading to significant improvements throughout the process. Scantech has been designing, manufacturing and supplying technological products to the minerals industry since 2002 to enable the availability of such realtime information to a mine or plant, with the benefits being enjoyed by a wide range of operators. This paper provides a summary of the available technologies used in the iron ore and steel industries, as well as providing a case study of their use at an Australian site, and a description of the potential benefits of a range of analysis equipment.

Aug 17, 2017

By Tobias Krull

The characterisation of iron ore from a materials handling point of view is paramount in order to provide the best possible design for the desired application and maximise equipment uptime at the lowest possible capital and operational expenditure. Problematic issues in materials handling applications often arise in the iron ore industry due to the high density of the ore as well as the abrasive nature of the product. One of the key issues encountered during the handling of iron ore is excessive wear due to either impact or sliding abrasion. The applications and equipment typically affected by accelerated wear issues are mass flow hoppers, transfer chutes and conveyor belts. These wear issues often result in unplanned down times and loss in production which can lead to a considerable loss in revenue. This paper provides an overview of the best practises in the materials handling characterisation of iron ore and discusses available techniques for the modelling of iron ore in applications where accelerated wear is experienced. The application is illustrated through a number of industry relevant case studies for which engineering design work was undertaken to successfully reduce the wear rates of different materials handling equipment.

Aug 1, 2018

By Daniel Antonio Kapper Fabricio

A avaliação das propriedades de mecânica da fratura dos materiais é uma necessidade crescente, sobretudo no setor de óleo e gás. Esse cenário exige a garantia da qualidade na execução de ensaios de tenacidade à fratura. Esse trabalho tem como objetivo realizar uma comparação intralaboratorial para o ensaio de tenacidade à fratura KIC variando o executante do ensaio, visando atender ao requisito de garantia da qualidade da norma NBR ISO/IEC 17025. Os resultados foram comparados através de análise de variância. As diferenças entre os operadores não foram significativas frente ao erro residual a um nível de confiança de 95%, sendo tal resultado considerado satisfatório.

Aug 16, 2017

By Ernst Lindemann

The SMS group has developed the ultrasound technology “HD scan” for inspection of the internal quality of as-cast products. This method of sample analysis requires less preparation work and is safer than the current, most common technique of etching and/or sulphur printing. Furthermore, this technology offers a three-dimensional view into the sample of the cast product and thus more representative information for a better quality evaluation. The internal quality evaluation can be performed automatically and objectively by software based on clear statistical methods. A quantitative centerline segregation rating can be assigned to each sample, based on the size and distribution of segregates detected by the unit. Internal crack statistic (length, position, orientation, etc.) and narrow side profile can also be measured. Grain macrostructure can also be visualized which allows for a potential optimization of casting parameters like strand cooling, soft reduction or electromagnetic stirring. The accuracy of the new method was proven by parallel metallographic investigations of more than 100 samples of different steel grades and sample shapes. Automatic defect evaluation and classification was compared against macroetching results. It was found that HD scan identified more defects and the visualization of the macro structure could be performed in more cases than with macro etching. All tests, comparisons, further developments and analyses for various steel producers and steel treatment companies have been conducted at the HD scan unit, located at the SMS group headquarters in Düsseldorf, Germany (Figure 1). Based on the results, SMS group has designed a unit which can be used in industrial scale.

Aug 17, 2017