Search Documents

By J. W. Baker

"The Kerr-Addison mine is on the northeast shore of Larder Lake in the township of McGarry, District of Timiskaming, Ontario. It lies just south of the highway leading to the town of Kirkland Lake, 25 miles to the west.The property was first staked in the summer of 1906, by a party of prospectors led by a Dr. Reddick of Ottawa. Subsequent assessment work resulted in the erection of a 20-stamp mill in 1908. Gold from this mill was used in the first gold coins to be minted in Canada. The operation did not prove successful, however, and mining was suspended. In 1914 a consider-able amount of underground development was undertaken by the Associated Goldfields Co., without success.In 1936 Kerr-Addison Gold Mines Co. carried out large-scale sampling from four adits driven into the hillside at the mine. Results were not satisfactory, but it was decided to drill one last deep diamond drill hole from surface. The hole cut a wide section of gold ore. With this encouragement, further development outlined a large tonnage of ore, and a 500-ton mill was put into production in May, 1938. In 1939, its first full year, the mine produced 54,480 ounces of gold and 2,732 ounces of silver. By 1955 the mill had been expanded to a rate of 4,549 tons daily, and in this year 427,193 ounces of gold and 23,490 ounces of silver were produced.From 1938 to the end of 1955 the total production, from 17,473,797 tons milled, has been 3,607,462.74 ounces of gold (0.2064 ounces per ton), and 182,278.56 ounces of silver, with a total value of $131,073,037."

Jan 1, 1949

By Patrick J. Hannigan

The pile foundation designer typically performs a subsurface exploration program and static pile capacity calculations before selecting a pile foundation type, length, and capacity. During construction, a pile installation criterion must be established to meet these design requirements. This installation criterion usually consists of a minimum penetration resistance or blow count to confirm pile capacity and may also include a minimum embedment requirement. This text will focus on use of wave equation analysis and dynamic measurements to meet design requirements. BEFORE THE WAVE EQUATION Since the mid-1800s, over 450 dynamic formulas for pile driving control have proliferated. In their simplest form, these formulas relate hammer energy to the work of soil resistance, or simply: W ? h = R ? s (1) Where W = ram weight h = ram drop height or stroke R = pile capacity s = pile penetration per blow

Jan 1, 1990

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1893 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management ` 188, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Haward-Canfleld Bldg. Santa Barbara, Calif.]

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcade Bids. Santa Barbara, Calif.]

Jan 1, 1952

By Walter E. Lewis

The Fort Randall Reservoir project, on the Missouri River at Pickstown, S. Dak., was designed by the Corps of Engineers and is part of the Missouri River Basin Development Program. The location of the project with respect to adjacent features is shown' in figure 1. When the project is finished, it will include a large earthwork dam and 12 circular tunnels, 8 of which will be equipped for power and 4 for flood control. Various phases of the construction have been contracted to independent companies, and at present four companies are working on different phases of the project under a rigid time schedule. Western Contracting Corp. is the contractor on stage II, earthwork; Johnson-Winston Construction Co. is the contractor for construction of the intake towers at the upstream side of the dam; McCarthy Improvement Co. has the contract for the power house and the outlet works on the downstream side; and Silas Mason Co. has the contract for driving the power and flood-control tunnels. The latter two companies use the same roads for ingress and egress to their respective work areas and the same general waste dump area. Under such circumstances, it is necessary that each company stay on a time schedule in regular sequence to avoid interference with the other.

Jan 1, 1951

By R. R. Sayers

The hazards connected with work under abnormal air conditions are becoming of increasing importance from a financial as well as a physiological stand- point, due to the extension of compensation laws to include diseases caused by dusts, toxic gases, and abnormal temperatures and humidities. The United States, with the excention of California, North Dakota, Wiscon- sin, Massachusetts, and Connecticut, is the only English-speaking country to-day where silicosis is not compensated.3 Cases of permenent total disability or death due to silicosis mar aprear in common-law courts, particularly in the States that have not recognized silicosis as an occupational disease for which compensation should be provided. Such cases have recently been tried in one State, according to a magazine editorial, not providing scheduled commensation for employees affected by silicosis, with results favorable to the claimant. Clearly established cases definitely linked with occupation as the cause may be expected to be recognized as deserving by juries and courts, and awards will be made. In one Atlantic Coast State, according to this editorial, 108 claims for silicosis, including 21 deaths therefrom, are said to have been filed against two small plants engaged in finely pulverizing quartz sand.

Sep 1, 1932

By Joint Micropiles Committee

"The three types of specifications which are used for micropile work are: • Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. • Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. • Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications.Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.The owner, designer and contractor will together be responsible for the tasks associated with the design, installation, acceptance, and performance of the micropiles. The installation of micropiles requires specialized equipment, techniques, and appropriate workmanship. Not every detail of the work can be specified, and not every potential problem can be anticipated. Therefore, a contractor who has demonstrated experience in micropiles must be selected to execute the work required."

Jan 1, 2004

By Donelson A. Robertson

Includes a review of the state-of-the-art of explosives loading in the crushed stone and cement industries of South Florida and the development of a field test program for alternatives. Emphasis is on the loading of small diameter (2 1/4" or less) explosives. Test results ire evaluated for operational and economic feasibility. Details are described of an explosives loading method which involves placing cardboard tubes with external couplings through the hollow drill steel and then Loading explosives into the tube casings after the drill rig has moved off. This method eliminates the hazards peculiar to loading explosives Through the kelly bar. The alternative method can be performed by existing drill rigs with or without minor modification. With modification, improvement in yield per blasthole and/or primary crushing rate provides opportunity so offset some or all of the additional cost.

Jan 1, 1978

By Robert A. Cummings

A rock mass classification system has been developed for recommending drift support requirements in block caving mines. This development follows a two-year program incorporating field observations of support practice and performance in rocks of different classes, at several U. S. block caving mines. Popular rock mass classification systems presently in use for tunneling were applied at the various field sites; and were evaluated for conformance with caving mine support requirements and for general utility to caving mine operations. The developed system (MBR System) accepts readily-obtainable engineering and geologic data to yield a rational estimate of support requirements. The background and development of the MBR system is described in this report (Volume I). The use of the system is given in the Manual, a separate volume (Volume II).

Jan 1, 1984

By A. J. Farstad

Electromagnetic location tests were conducted by Westinghouse Georesearch Laboratory under the sponsorship of the U. S. Bureau of Mines at the Galena Mine in Northwest Idaho. The objectives of these tests were to evaluate the performance in deep hardrock mines of an electromagnetic location system previously developed for the U. S. Bureau of Mines for use in coal mines. Tests were performed using long wire transmitting antennas as well as horizontal and vertical transmitting loops at depths from 3000 feet to 4300 feet (995 metres to 1311 metres). Surface measurements were made of magnetic field strengths, field strength patterns, and background noise, These measurements were compared with theoretical predictions for a homogeneous ground conductivity consistent with this particular geologic region. The results of the Galena Mine tests show conclusively that light-weight portable electromagnetic transmitters can be effectively utilized to provide uplink communications and location information in deep hardrock mines. Typical metal mines such as Galena utilize deep vertical shafts for mine access and haulage and these shafts produce signal enhancement at the surface from underground electromagnetic transmitters by as much as 30 dB. The results also show that horizontal wire configuration can serve as an effective alternative to the magnetic dipole antenna as a rescue transmitting antennaa and can be used when the required area is not available for deployment of a loop antenna. In spite of the electromagnetic coupling effects observed in the vicinity of the shafts, the location accuracy obtained still provided useful information on the general location of the transmitting sources involved. The horizontal wire location accuracy was within 46 metres, while the vertical magnetic dipole and the horizontal magnetic dipole accuracies were within 152 metres and 110 metres respectively at a 915 metre depth.

Jan 1, 1973

By R. S. Rosso

A program to investigate the effects of hardened washers on the uniformity of roof bolt tension and the resulting ground control in an underground mine was carried out. The complete roof bolt installation and roof bolt loads, mine convergence, and bed separation were monitored for a period of five months. The results show no evidence to support or refute the theory that mechanical roof bolts offer better support when they are installed with a high uniformity of tension. Also shown is the fact that if the bolts are installed with a maximum deviation from the mean torque of ±15% the addition of hardened washers significantly improved the uniformity of the installed tensions in the roof bolts.

Jan 1, 1977

By G. B. Shea

"In 1928, there were 47 fatal accidents in the California petroleum industry, 14.6 per cent more than occurred in 1927 when 41 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. This increase in the number of fatal accidents for 1928 has caused the first upward trend in the fatality curve of the California petroleum industry since 1923. In no other year during the 6-year period have the fatalities in any one year been greater than those for the preceding year. This fact should be given serious consideration and study by the petroleum industry, and an endeavor should be made to cause the number of fatalities again to decrease and conform to the previous gradual declining trend of the fatality curve.The following chart shows the trend of fatal accidents during the past six years:Of the 47 fatalities in 1928, 30 occurred in the drilling and producing division, 1 in the pipe line and transportation division, 14 in the refining division, and 2 in the sales and marketing division. A comparison of the number of fatalities in each division for 1927, and 1928, is given in the following table:3"

Sep 1, 1929

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004

By R. S. Dean

"Applied Mineral Physics, by R. S. Dean.- This is an introduction to the seven papers that follow. It discusses the practical aspects of mineral physics and outlines the theo¬retical viewpoint underlying the investigations reported herein.Explosive Shattering as a Possible Economical Method of Ore Presentation By John Gross and C. E. Wood. - It is shown that explosion shattering by impact is favored by large charges and by low ratio of water to charge. For 400-gram charges of dolomite crushed through 48 mesh the steam costs are less than 5 cents per ton of dolomite obtained. This is within the range of present steam costs for ball-milling dolomite.Electrical Properties of Minersl Aggergates I. Natural and Artificial Aggregates Crystallized Lead Sulphide By R.S. Dean and John Koster - This paper deals with the electrical properties of natural and synthetic galena. It is shown that massive crystalline galena has a normal positive temperature coefficient of resistance, whereas fine-grained steel galena has a negative temperature coefficient, the curve R v. T being exponential in form. That steel galena behaves somewhat like a leaky condenser is indicated by ballistic and alternating-current bridge measurements. In determining the cause of the erratic results of alternating-current resistance measurements it was observed that the measured re¬sistance was a function of the current through the specimen. The direct-current resistance was found to be proportional to the square of a superimposed radio-frequency current and independent of the frequency.The influence of grain size or the amount of metallic interface on the voltage-current characteristics at various temperatures on synthetic galena pastilles was studied. It is proved that the volts v. amperes curves are linear for all sizes and temperatures, that they have an intercept which is apparently a linear function of the temperature, and that their slopes are exponential functions of the temperature and give rise to a negative temperature coefficient of resistance.Apparatus for determing the Magnetic Constants of Mineral Powders by V,H, Gottschalk,and C. W. Davis.- A modified isthmus permeameter having a spark-suppressed primary and a multiplier in the secondary circuit to regulate the effect of capsules functioning as a twin isthmus is used to obtain quantitative data and normal induction and hystersis curves from small amounts of powdered material at fields surpassing 3.000 oersteds. Data and curves are given to demonstrate the calibration of the apparatus and the reproducibility of its results. Applications and limitations of the apparatus are noted.Magnetization Curves for Magnetite Poeders by V. H. Gottschalk and F. S. Wartman.- This paper gives measurements on four lots of purified and analyzed magnetites in mixed fractions with especial reference to the variation of permeability with grain size and with dilution by an inert material."

Feb 1, 1935

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

By J. Bickson, C. DeGennaro, J. Homer, M. Girman

Powered haulage and haul truck-related fatal accidents are among the most frequent at surface mines. Industry organizations developed guidance on accident scenarios to address haul truck and mobile equipment collision-related accidents. However, there is a need to investigate accident data to prioritize these scenarios and identify factors relevant to developing validation methods for collision warning/avoidance technologies and determining their capabilities and limitations. Standards and effective validation methods are necessary for improving system efficacy within mining operations and promoting industry adoption. To address these needs, researchers from the National Institute for Occupational Safety and Health (NIOSH) investigated available powered-haulage and machinery-related fatal accident reports documented by the Mine Safety and Health Administration (MSHA). Their objective was to gain a perspective for informing the development of test protocols and validation methods through determining the most prevalent accident scenarios and related factors. Our findings afford insight for addressing the most prevalent haul truck scenarios and relevant factors within U.S. surface mining environments.

Mar 2, 2022

By H. C. Fuller, E. L. Anderson, F. S. Wartman, M. A. Cook

"This paper gives an account of the production of ductile-grade titanium powder in 100-pound batches by reduction of purified titanic chloride with magnesium, followed by grinding, leaching, and magnetic separation of the reaction product. Apparatus, technique, and methods of controlling product quality are described, and some data on operating costs are given.Although man has been aware of the existence of the element titanium for over 150 years, only recently has the metal itself been available in a form pure enough, particularly with reference to absorbed gases, to allow an estimate of its physical properties. In comparison with mild steel, the tensile strength of titanium is about the same, the resistance to atmospheric corrosion greater, and the specific gravity much less.These properties suggest the usefulness of titanium as a structural material for applications requiring resistance to atmospheric attack and a good strength-weight ratio. Although known reserves of titanium, high-grade enough to be useful at present are not sufficiently extensive to predicate that titanium might supplant iron, aluminum, and magnesium for structural purposes, the reserves are large enough to make its use as a structural material quite feasible in certain fields in which its unique properties are required.As a result of these considerations, the Bureau of Mines station at Tucson initiated an, investigation into the technology of titanium in 1938. First, a critical survey and small-scale trial of virtually all suggested methods7/ for producing the metal was made. The method devised by Kroll8/ seemed best adapted as a source of metallic titanium for, although the purity of the product was not as high as that of products from some other processes, it seemed that modifications in technique necessary for larger-scale production could be made more easily.Essentially, in applying the Kroll process, titanium tetrachloride was reduced to metallic titanium by adding the chloride slowly to molten magnesium contained in a molybdenum-lined iron reaction chamber filled with a protective atmosphere of argon. After reduction to the state of completion desired, the reduction mass and chamber were allowed to cool. Then the chamber was opened, and the reaction mass, consisting of titanium, magnesium chloride, and some unused magnesium, was removed by suitable means. Most of the magnesium chloride and metallic magnesium were removed by leaching in dilute hydrochloric acid. The leached sponge was then ground wet in a ball mill, releached in strong acid, and dried Removal of free iron by magnetic separation completed the production process.Development of the Kroll process by the Bureau was undertaken first at the station at Salt Lake City, in 1942 and the amount formed per run was increased in several steps from a few grams to pounds.9/ In addition to increasing the size of batch over that used by Kroll, the technique was simplified somewhat by the use of unlined reaction vessels."

Aug 1, 1949

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By J. R. Campbell

The need for standardizing methods of arriving at definite conclusions regarding the cleanability of a given coal, and for measuring the performance of coal-cleaning equipment, is constantly increasing. Earlier notes by the author on this subject are amplified in this paper, because he believes that better preparation of bituminous coal is a partial solution of the coal operators' troubles. Washability Studies The term "washability" of coal was coined when washing was the universal method of separating coal from its impurities by utilizing their difference in specific gravity. This and analogous terms are still used in their broad sense although pneumatic or air separation is now used to clean coal. These terms are so used in this paper. Too much time or money can hardly be spent on "feed surveys') to get a "picture" of the coal that is to be cleaned. There have been too many "rule of thumb" methods used. Screen analyses and "sink-and-float" tests on the raw coal enable the coal operator and washery man to predict within reasonable limits the results that may be expected from any efficient cleaning apparatus. The sizes to be examined to get the picture are optional to the investigator. In modern wet washing, the range is from 4 to 0 in. Hand-picking on properly constructed belts is perhaps the standard for cleaning above these sizes. A good picture of the coal may be obtained by the following screen analysis: 3½ to 1¼ in. 1¼ to 3½ in. ½ to 5/16 in. 5/16 in. to 14 mesh 14 to 28 mesh 28 to 48 mesh and for very complete data on the fines: 48 to 100 mesh 100 to 200 mesh and through 200 mesh

Jan 1, 1930