Search Documents

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By J. Gibson

"INTRODUCTION As one of the most pressing and important political debates of this century, climate change has captured global attention and is forcing governments to take action towards decreasing GHG and carbon emission levels below what was previously thought to be necessary. With the ever-increasing price of diesel fuel accompanied by the popular topic of carbon taxes and greenhouse gas emissions, the mining industry is looking to industry specialists for assistance. The benefits of a no-idle policy reach far beyond carbon reduction and fuel savings, ranging from decreased maintenance to increased engine life. With products like battery powered A/C systems and diesel-fired heaters, going no-idle is easier today than ever before. With both systems being manufactured to withstand the harsh environments of the mining industry, the end user will see a seamless change from conventional, inefficient belt-driven systems to future, stand-alone mobile equipment HVAC. THE HISTORY OF GHGS AND CLIMATE CHANGE In 1896 Svante Arrhenius first claimed that the combustion of fossil fuels may eventually result in enhanced global warming, but not until 1955 did Gilbert Plass draw global attention to global warming by summarizing that adding carbon dioxide to the atmosphere would intercept infrared radiation and thus warm the earth. Then in the early 1960’s Charles Keeling developed modern technology to produce concentration curves for atmospheric CO2 (Figure 1). In 1988 the Intergovernmental Panel on Climate Change (IPCC) was founded by the United Nations after acknowledgement of a rising global annual temperature. The IPCC consists of over 2500 scientific and technical experts from more than 60 countries, and because climate change could not be solved by a single country, the Kyoto Protocol was negotiated in 1998 requiring all participating countries to reduce their GHG emissions by at least 5% from the 1990 levels. The Protocol was signed by 186 countries in 2001 (since then several countries have retreated from the agreement, including the United States)."

Jan 1, 2015

By L. F. Willmott

The Bureau of Mines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipeline for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By K. Takahashi

Generally speaking, wastewater coming from the metallurgical process for recovering precious metal contains precious metals such as gold (Au), platinum (Pt), palladium (Pd), Silver (Ag), etc., which concentration is about 10 mg/L. In addition, there are other metals such as copper (Cu), iron (Fe), which concentration varies from several mg/L to more than 10,000 mg/L. It should be noted that the concentration of metals in wastewater is relatively high, considering the fact that these metals of similar concentration can be found in ores. However, most of these valuable metals are not treated, due to the high processing cost and technical problems. Within this frame, the authors put forward a new process that includes neutralization/reduction, precipitation and fusion. The idea is to recover and recycle Au, Ag, and Pd metals as well as protecting the environment by saving the resources. It was found that this new process was able to recover more than 90% of Au, Ag and Pd.

Jan 1, 2014

By Christian Hoyme, Jochen Maurer

Most of the current foundation projects are suffering from disconnected information silos. In the first silo there is the planning of the project with corresponding data, presented by paper or digital drawings. Here will Building Information Modeling (BIM) be one of the trends for the future. We will see more and more projects leaving the “old way” of 2D drawings and moving into 3D planning including metadata of the foundations. But even with a perfect BIM model of a jobsite, we are not at final end of digitalization. While execution of the project at the jobsite, a second data silo is evolving. Data collected directly from construction equipment and manual measurements is currently undervalued in most projects. Paper is passed to the equipment operator and major data from measurements on site are noted on paper and digitized afterwards. Automatically collected data is not be used to create site progress reports or similar report. So, the real “data” just flows around without connection to any other data already existing in projects. And then the third silo arises: The documentation of the project. Data collected on paper es reentered to create some basic documentation of the work handed over to the client. Spreadsheet software is still the “tool-to-be-used” to create at least some documentation. Finally, the documentation is not connected to the data created while planning and not connected to the automatically collected data from the jobsite. A connected jobsite in the foundation industry must link these information silos and have to create a full data-workflow from the design through the execution to the as-built documentation. INTRODUCTION Building information modelling (BIM) is currently the most popular term of construction business in Germany and probably all over the world. But as often there are many different definitions out there and everyone has his own definition or at least understanding what BIM is about. But for sure it is the most relevant for the construction industry in the near future. Most popular is the digital twin for the upper structure of a building. In most cases the BIM models just shows the building itself, but there is more to be implemented. For example: projects where a special foundation is needed, BIM should include also the foundation elements with meta data. There are several advantages. Not only the clash detection of anchors, but also the possibilities to check the interaction with neighbor constructions, power lines and so on are a use case. For sure most of the special foundation elements are not relevant for the whole lifecycle of a building. But during construction and later the demolition the information about the hidden elements is important and gives a benefit to all stakeholders. In the future there will be not the question: “What is already in the ground?”. The risk for following construction projects on the same ground will be minimized.

Jan 1, 2019

By Henry P. Cole

A series of studies are described that identify critical health and safety skills needed by underground coal miners for coping with mine emergencies. First aid and self-rescue and escape were selected as two broad performance domains that include many subordinate skills needed for preventing, recognizing, and coping with mine emergencies. The performance domains and their objectives were used to direct the development of simulation exercises that permit miners to experience mine emergencies in the safety of a training room. The exercises are based upon research with similar simulations for the training of flight crews and medical personnel in information gathering, judgment, and decision making skills. Exercise content is drawn from actual mine accident and disaster case studies. The exercises incorporate recent principles of cognitive psychology and instructional design. Initial studies in annual refresher training classes suggest the exercises are stimulating for miners and their instructors, easy to use and read, sufficiently complex and authentic to challenge experienced miners, and useful devices for both teaching and testing critical problem solving skills required for preventing and minimizing emergencies.

Jan 1, 1988

By Greenwood J. N

This is the fourth paper in the series on Australian w,ar materials and the work was undertaken as part of the programme for producing hard carbides. It had been intended to determine the influence of tantalum and columbium' carbides in mixtures with tungsten carbide. Owing to other, urgent developments, it has not been possible to proceed with that programme.1. THE PROCESSING OF A TANTALITE ORE(a) The OreThe minerals in which tantalum and columbium most commonly occur are tantalite and columbite. These two minerals are the end members of an isomorphous series of tantalates and columbates of iron and manganese, but in nature the series grade into each other.Some of the best deposits of tantalum and columbium ores in the world occur in the north-west of Australia. Until recently tantalite low in columbium was the only mine~al in demand but discoveries of extended uses for columbium, e.g., addition of ferro-columbium to high chromium I steels inhibits intergranular corrosion (weld decay), have created a demand for columbite low in tantalum as weB. Both of these types of' ore occur in the Pilbara district in Western Australia and most of the ore mined is exported to America after a preliminary grinding and concentration by gravity.A sample from the Bynoe Harbour locality, west of Darwin, was used in this investigation. It consisted of coarse lumps of tantalite with quartz in minor amounts. Cassiterite w.as also present. A recent investigation!l) gave the analysis as:

Jan 1, 1943

By C. Dauber

Implementing new technologies in industrial operations entails the challenge of measuring the improvements gained by the applied technology. Nevertheless, it is absolutely essential to assess the technical and economic benefits in objective and comprehensible numbers to create a platform for further management decisions. Underground coal mines are characterized by numerous, quite complex procedures which make it difficult to determine the specific economic benefit of a new machine, technique, or method. In the OPTI-MINE Project funded by the European Union?s RFCS programme, five underground coal mines applied the latest information and communication technologies (ICTs) to improve efficiency, mine safety, occupational health, and environmental im-pacts. An integral part of the project is the assessment of these technologies by using key performance indicators (KPIs). The paper will describe some examples of the selected KPIs and the preliminary findings.

Jan 1, 2014

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. When enough circulars have boon completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed b., bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual nines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); Ventilation; wage, contract and bonus systems, etc.

Jan 1, 1931

By S. R. Dindarloo

Although blasting is one of the most widely used methods for rock fragmentation, it has a major disadvantage in that it causes adjacent ground vibrations. Excessive ground vibrations can cause a wide range of problems, from nearby residents complaining to ecological damage. Prediction of blast-induced ground vibration is essential for evaluating and controlling the many adverse consequences of surface blasting. Since there are several effective variables with highly nonlinear interactions, no comprehensive model of blast-induced vibrations is available. In this study, the support vector machine (SMV) algorithm was employed for prediction of the peak particle velocity (PPV) induced by blasting at a surface mine. Twelve input variables in three categories of rock mass, blast pattern, and explosives were used for prediction of the PPV at different distances from the blast face. The results of 100 experiments were used for model-building, and 20 for testing. A high coefficient of determination with low mean absolute percentage error (MAPE) was achieved, which demonstrates the suitability of the algorithm in this case. The very high accuracy of prediction and fast computation are the two major advantages of the method. Although the case study was for a large surface mining operation, the methodology is applicable to all other surface blasting projects that involve a similar procedure.

Jan 1, 2015

By W. J. Birch, A. Wetherelt

The scaled-distance model for blast vibration analysis is the standard method employed throughout the surface mining and quarrying industries to model Peak Particle Velocity (PPV) data. Although empirical, the method is widely accepted and through the simplicity of its application and ease of graphical verification is set to remain a popular option. The validity of the technique relies principally on the fundamental parametric assumption that blasting data is normally distributed. Throughout the evolution of scaled-distance modelling, this is an issue that has most often been presumed rather than proven (most likely due to the tediousness of the calculations involved). In the few cases when normality has been given some degree of consideration, the result has been the product of a simple visual inspection of frequency distributions: clearly unsatisfactory. However recently the soundness of this assumption has been brought into question, with obvious connotations for blast modelling in general. This paper considers this fundamental issue and seeks to investigate the normality hypothesis within the blasting context through an in-depth statistical analysis of what possibly can be described as an ‘ideal’ blasting dataset. This being a rare case study concerning an opencast coal site in England, where for the entire life of the site every single blast was monitored and recorded through the use of permanent monitoring stations. This has provided a unique ‘total population’ dataset of considerable size from which the assumptions of normality are put to the test.

Jan 1, 2005

By Rick Collins

Presentation Agenda 1.Sudbury Basin 2.Diamond Drilling 3.Planned Production 4.Safety 5.Timeline 6.Sustainable Development 7.Scope Elements 8.Progress 9.Delivery Approach 10.Owners and EPCM Roles 11.Contract Styles 12.Mine Systems & Technologies 13.Q & A

May 1, 2009

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

By E. G. Baglin

As part of an effort to decrease U.S. dependence on imports of critical and strategic metals, the Bureau of Mines investigated three leaching methods for extracting the base metals and recovering platinum-group metals (PGM) from matte prepared from Stillwater Complex flotation concentrates. Because of a limited supply of natural material, synthetic matte of composition similar to matte prepared from natural concentrates was used to devise the extraction sequences. The validity of the sequences was verified with matte prepared from Stillwater concentrates. In two-stage matte leaching, first-stage H2S04 leaching extracted 99 pct of the nickel and iron from the matte but negligible amounts of copper and PGM. Second-stage oxidative leaching with Fe2(S04)3 or FeC13 solubilized more than 98 pct of the copper and no precious metals. Sequential leaching, in which acid and oxidizing lixiviants were added sequentially to the matte without an intervening filtration step, extracted 99 pct of the Fe, Ni, and Cu. A roasting-leaching technique, in which the residue from first-stage leaching was roasted between 360° and 500° C before a second leaching with H2S04, solubilized 98 pct of the copper. The three leaching methods yielded high-grade PGM residues containing more than 98 pct of the PGM in the matte.

Jan 1, 1982

By Donghai Li, Cheng Pan, Xuewei Lv, Mei Liu, Enguang Guo

"Phosphorite is the main raw material for the production of phosphorus in chemical industry. More attentions have been drawn to the phosphorite concentrate beneficiated from low-grade phosphorite due to the decrease of high-grade phosphorite. For another, the agglomeration process is necessary for the phosphorite concentrate after beneficiation process. The mineralogy and sintering process of the phosphorite from Leshan, China were studied in this work. The result shows that the main phases in the phosphorite are fluorapatite (Ca3(P04)3F), hydroxylapatite (Cas(P04)3(0H)), quartz (Si02) and dolomite (CaMg(C03)2). The yield of the sinter increases with increasing the carbon dosage to 7%, and then decreases when it continuously increases. Similar regularities were found for the strength and the content of P20s of the sinter. The best strength of the sinter as well as its P205 content were discovered when the carbon dosage is 7%. Fluorapatite ((Ca5(P04)3)F) is the main phase in the sinter while fuggerite (Ca2MgSiz01) is the main binder phase.IntroductionPhosphorus is an important foundation industrial raw material of national defense industry, food industry and chemical industry, where it is used to produce red phosphorus, phosphonium hydroxide, phosphorus pentasulfide and phosphoric anhydride[l-2]."

Jan 1, 2013

By E Corpuz, J Weissman, S Winter, R Evans

The surface-to-inseam (SIS) directional drilling technique has been utilised at Oaky Creek Coal for more than a decade to predrain both the Oaky No 1 and Oaky North mining areas. The cumulative drilling program constitutes a total of 140 lateral and 200 vertical holes, and 405 km of lateral drilling.The use of SIS gas drainage has been successful with the following site-specific benefits being recognised:ability to drain German Creek seam gas contents to residual gas levels of new mining areas within an 18-month period from commencement of well productionstructural geological verification of the mine design well in advance of development mining occurring in an areaability to conduct successful predrainage of the overlying Aquila seam to reduce subsequent goaf emissions.Appropriate and up-to-date geological knowledge during the design and drilling process is a significant influence to achieving success. Vertical production wells need to be located in a position that is most effective to remove water from hole. The lateral hole should not include intersections with significant geological structure.SIS drilling provides continuous seam roof/floor data to help define seam geometry and locate geological hazards with high accuracy. In faulted ground and with variable seam gradients, SIS data can resolve geological ambiguities from seismic sections and enhance seam correlation that would otherwise be available only from discrete and closely-spaced infill vertical exploration drilling.Here, we review some examples of SIS configurations and practice to highlight key learnings in drilling long inseam holes (up to 1900 m per arm) ahead of development and mining. Aspects on prerequisites, evolution of network design, tolerances and drainage outcomes in a variety of geological situations are discussed as technical basis towards a viable and effective SIS drilling program.CITATION:Corpuz, E, Evans, R, Weissman, J and Winter, S, 2015. Surface-to-inseam (SIS) drilling at Oaky Creek coal mine – SIS design aspects and drilling environment, in Proceedings The Australian Mine Ventilation Conference, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Christopher J. Bambridge, Lee Seng Hoor

The Stormwater Management and Road Tunnel (SMART) Tunnel is a world first in the use of tunnel space transmitting both road and water through the same spatial envelope. The unique aspect of the SMART project is that the highway decks are used periodically for the conveyance of water. This aspect of the project has posed its own technical challenges that have been overcome in the design stage of the work allowing the project to be taken forward to construction with confidence in the systems to be Installed in the tunnel.

Jan 1, 2005

By David Harrison

Exxon Minerals Company uses geostatistical techniques for ore resource evaluation of its mineral projects. These techniques provide the most reliable estimates of recoverable tonnage and grade and uniform and realistic confidence limits. A schema has been developed which categorizes the company's successive evaluation phases. Clear separation is intended between geostatistical estimates and other factors in project evaluation such as mining, metallurgy, and economics. Company management seeks consistent and reliable estimates for investment decision-making and to meet growing demands for disclosure of mineral assets.

Jan 1, 1983